Renewal of surveyed off furniture at AF Stn Bihta

Amount

Chair dinning PBOR MAP:- All wooden work shall be of Ist class teak wood, rear legs shall be of 910mm long x 35mm x 50mm. Front legs made out of 35mm x 50mm x 75mm thick 40 density foam cushion cover with good quaility tepestry cloth as approved on seat with 12mm thick commercial ply wood shall be fixed 75mm x 75mm x 25mm teak wood stopper fixed with main frame and legs side rail of chair shall be of 65mm x 65mm x 25mm. Stiffener shall be of 25mm x 20mm teak wood . All wooden work shall be of french polish.Rest all as per drg and directed.

Sofa set to seat five:- All as shown on drawing. The set consist of one long piece of three seat and two small pieces of one seat each. All wood shall be of first class hard wood teak (MP). Legs shall be oif 70 x 35mm in section made to shape as shown on drawing. Wooden arm shall be made to shape out of 35mm x70 mm in section teak wood. Front and side rails shall be of 35mm x 100 mm in section teak wood. 40 x 40 mm in section teak wood bearers shall be provided at the bottom of seat over which 50 x 20 mm wooden battens, twenty one numbes, shall be fixed equally spaced in the long piece meant to seat three. back shall be made of frame of rails and styles of 70 x 35mm in section teak wood. The filling in the frame, thus made, shall be done with 14 numbers teak wood battens of 50 mm x 20 mm in section fixed equally spaced in the loing piece meant to seat three. 30 x 50 mm teak wood rail shall be provided between back legs to support back frame. 100 mm thick cushion of cool foam of 32 density covered with best quality tapestry cloth shall be provided at seat as directed by Engineer-in-charge. 100 mm thick cushion of cool foam of 32 density 530 x 500 covered with best quality tapestry cloth shall be provvided at back. Seven numbers 50 x 20 mm in section teak wood battens shall be fixed equally spaced in single piece seat. back shall be made of frame of rails and styles of 60 mm x 35 mm in section teak wood. The filling in back frame of single piece shall be done with four numebrs 50 x 20 mm in section teak wood battens. the legs and the frame shall be made for single piece seat as provided for long piece to seat three. the seat and back shall be of 100 mm thick cushion of 32 density of size 530 x 500 mm. All wood surfaces exposed to view shall be french polished with lacquer finish.

Table dining for 6 per:- All as shown on drawing. Overall size shall be 1500mm long, 900mm wide and 760mm high. All wood shall be of first class hard wood teak (MP). Legs shall be of 60mm x 60mm in section at top and 40mm dia at bottom . The square section of 60mm x 60mm shall be up to 100mm from top of legs. The four legs shall be joined together at top of les with 25mm x 100mm insection top rails in short and long sides. A stiffener of 25mm x 100mm in section shall be provided in the center of long top rails, joining long top rails. Top of table shall be of 19mm thick block board commercial with 1.5mm thick plastic laminated sheet fixed over it with fevicol. 4mm thick teak wood edging shall be provided al -round the top of table. All wood surfaces exposed to view when placed in position shall be french polished with high gloss finish. The quantity of polish shall be 250ml . Hard rubber/ PVC shoes shall be provided to the bottom of legs.

Table centre:- All as shown on drawing. Overall size shall be 900mm long. 450mm wide and 400mm high . All wood shall be of first class hard wood teak (mp) legs shall be of 45mmx45mm in section at top and 25mm dia at bottom. The four legs shall be fixed together at top of legs with 25mmx50mm in section top rails in long and short sides. A stiffener 25mmx50mm in section shall be provided in the center of long top rail, joining the long top rails and shall be of teak wood. Top of table shall be of 19mm thick block board commercial, with 1.5mm thick plastic laminated sheet fixed over it with fevicol . 4mm thick teak wood edging shall be provided al-round the top of table . All wood surfaces exposed to view whin placed in position shall french polished with high gloss finish . The quantity of polish shall be200militre approx.

Chair easy:- All as shown on drawing Overall size shall be 640mm long, 720mm wide and 740mm high . All wood shall be of teak wood (mp) . Legs shall be out of 40mm dia. front legs shall be joined together with front front rail of 50mmx 25mm in section. Seat shall be trapezoial in shape with 510mm long front and 480mm long at rear. Back of seat frame shall be out 0f 70mm x40mm and front of seat frame shall be out of 55mmx25mm in section teak wood . side frames of back rest shall be out of 70mmx25mm in section teak wood . horizontal rails at top and bottom of back rest shall be of 55mmx19mm in section teak wood. arm rest shall be out of 65mmx25mm in section teak wood and two in numbers. 600mm long. shall be provided as shown on drawing caning shall be done with best quality shah/premier brand cane weighing ont less than 6gms per 10 running meter and shall be of 2mm wide and 0.04mm thick. The approx. weight of cane used in seat and back shall be 400gms. The caning. shall be done in godrej pattern as shown in drawing no . FD-3(M)Sheet1/1dt. 27.9.71. All wood surfaces exposed to wiew when placed in position shall be french polished with high gloss finish. Quantity of polish requred shall be 500 mili litre of polish approx.

Bed hard steel:- (a) Overall size of the Bed shall be 2050x900x500mm (b) The framework shall be made of CRCA box sections as under (i) Long Rails- 25x65mm box section of 16 guage (ii) Short Rails- 25mmx65mm box section of 16guage (iii) Frame work of Footboard and Headboard shall be -18x18mm box section of 16 guage (iv) Stiffeners -4Nos each of 25x25mm box section of 16 guage. (c) Headboard and footboard shall be made out of 18 mm thick Pre-laminated Particle Board both side Teak finish laminated, BWR, exterior grade, conforming to IS-12823 screwed to 18mm thick MS strip all as per details shown on drg. (d) Head rest and foot rest is to be supported by 65mmx25mm MS rectangular pipe of 18 guage all other MS square pipe shall be of 25mmx25mm of 18guage. (e) The Main frame work of Foot Board and Head board shall be alongwith legs shall be made out of CRCA box section of 38mmx38mm with 16 guage. (f) Top of the bed shall be provided with 12mm thick plywood BWR grade conforming to IS-303 (g) Hard rubber shoes to be provided to each legs (h) All CRCA/MS members shall be pre-treated with epoxy polyester powder coating (Black) 70 microns by 7 tank process and Oven Dried internally & externally with the following specifications (i) Dry Film thickness more than 45 microns (ii) Salt Spray test to with stand more than 1000Hours (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H (g) All other items, fittings and fixtures shall be as shown on drawings and as directed by GE. (h) Mattress as shown in the drg is outside the scope of this contract.

Almirah large with shelves steel:- All as shown on drawing. Overall size shall be 920 mm x 485mm x 1985mm. The base shall be made of two numbers mild steel sheet channel bases made in U-shaped with ends covered. Mild steel sheet shall be 1 mm thick. The base channel shall be welded at 50 mm from each end of the length of 920 mm and shall be up to full width of 485 mm and shall be 100 mm high. Top, sides, bottom and back of almirah shall be manufactured with using 1.00 mm thick mild steel sheet.Four shelves equaly spaced of 1mm thick mild steel sheet shall be provided to make five compartments. Front shutter shall have two leaves of equal size. One chromium plated steel handle with locking device shall be provided as shown on drawing. The locking device shall be three way locking device. Front shutter leaves shall have three butt hinges of 75mm fixed to each shutter and shll be side hung. All joints and welding and fixing shall be done in accordance with the standard work manship. All steel surfaces internally and externall, exposed to view wehn placed in position shall be given powder coated olive green enamel paint over a coat of primer after preparation of steel surfaces where ever working of painting shall be feasible. Locks shall be of Godrej pattern. Two keys shall be provided with each lock. Rest all as per drawing.

Table 3'x2' w/o drawer (900x600):- All as shown on drawing. Overall size shall be 900mm x600mm x760mm . Steel frame shall be of 800mm x 500mm x 742mm. Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm. Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm top rails on long and short sides. Two short stiffeners joining legs in short sides at 100mm from bottom shall be provided inthe middle of short stiffener joining short stiffeners with 25mm square mild stell tube of wall thickness 1.6mm at 100mm from bottom of legs. Top of table shall be of 18mm thick pre- laminated particle board with teak veneer shade and PVC edging al - round the top of table, irrespective of what is shown and specified on drawing. PVC / hard rubber toes shall be provided to the bottom of legs. All steel surfaces exposed to view when place in position shall be painted with two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces.

Chair CB steel with arm:- All as shown on drawing. Overall size shall be 535mm wide, 650mm deep and 900mm high, Seat shall be 455 high from floor. Conduit pipe used for frame shall be 20mm dia steel tubing having wall thickness 1.6mm welding of frame where directed by GE and in running, welding, grinded to give smooth surface. Wood for seat and back , where canning is to done shall be of first class hard wood teak wood for handles shall be teak wood . weaving of cane shall be done with primier of shah brand plastic cane in Godrej pattern as shown on drawing No- FD-3 (matric) sheet 1/1 Cane shall be 2mm wide and 0.4mm thick Gola type weighign not less than 6 gram per 10 running meter. Wood surfaces of seat back and handle shall be painted with high gloss paint black in tint before canning, painting shall be done with spray machine after preparation of wooden surfaces to achieve smooth finish . All iron surfaces exposed to direct view shall be painted with enamel paint two coats over a coat of primer after preparation of steel surfaces to achieve smooth finish. Bottom of legs shall have rubber shoes.20mm x3mm flat iron strips shall be provided at bottom and back to provide the supports to seat and back. Strips shall be two each to seat and back. Flat iron strips shall be welded to frame of chair as directed by GE.

Chair writing with cushion:- The overall size of the chair shall not be less than 475mm wide and deep and 580 mm high at seat from ground level. The seat and back are to be made up of 1.2cm thick hot-pressed plywood, uphoistered with fabric upholstery covers and moulded melamine foam. The back foam is to be designed with contoured lumbar support for extra comfort. The foam is to be molded with density 45 +/- 2 kg/m3 and, hardness 20 +/- 2 at 25% compression. Arn rest shall be one piece. All metal parts shall be dry powder coated in thickness more than 50 microns. All as shown on drawing.

Table dining 1200 x 900 x 760 mm:- All as shown on drawing. Overall size shall be 1200mm x900mm x760mm . The top shall be 18mm thick pre- laminated particle board of grade- I exterior quality as per IS-14587 shall be used. All joints & fixing shall be done by Computer numerical control in accordance with the standard work man ship/ specification. Dining table of 1200mm x 900mm size shall be provided with only one stiffener in the center of the table. All wood work and veneered surfaces shall be french polish as specified . Rest all as directed and shown on drg.

Rack shoe steel:- (a) The main side frame shall be made of 25 mm dia, 18G CRCA pipe and the main shelf frame with 19 mm dia, 18G pipe. (b) There shall be five shelves,each size 300 x 700mm and the space of each shelf shall be covered by3 mm dia MS road three in length-wise and nine width-wise. (C) Finish :- All CRAC/MS members shall be pre-treated with epoxy polyester internally & externally with the following specification. (i) Dry film thickness more than 45 microns. (ii) Salt Spray test to with stand more than 1000 hours. (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H (d) Welding process shall be of IMG (Metal inert Gas) type using Carbon dioxide and Argon blend. (e) Rest all as per drg or as specified.

RK STEEL FABRICATORs

Star Sofa House