SPECIAL REPAIR TO BLDG NO T-71 ( COOK HOUSE) T-72( BARRACK) ANDSP-138 AND SP-107 AT SUKNA MIL STN UNDER GE SUKNA

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of cement concrete (un-reinforced ) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate), as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of (3:1), complete all as specified and directed.

M&L for 75mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub-base of flooring, etc, finished concrete surfaces even and rough to receive cement screed, complete all as specified and as directed.

M&L for providing 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded crushed stone aggregate) , as in sub base of floor/path etc. complete all as specified and directed.

M&L for cement concrete (1:2:4) type C-1 (using 12.5mm graded crushed stone aggregate) as in coping, bed block for filling hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones bed plates,water troughs and the like including weathering, slightly rounded or chamfered angles & throating as including form work as requried complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter complete all as specified and as directed.

M & L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork with fly as Bricks(old size), straight or curved on plan exc 6m mean radius built in Cement morter (1:6), complete all as specified and directed

M&L for Brickwork with fly as Bricks(old size), straight or curved on plan to any radius in half brick walls built in Cement morter (1:4), complete all as specified and directed

M & L in repair Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and as directed.

M&L for brick work with fly ash Bricks(old size), straight or curved on plan to any radius built in CM (1:4) as in half brick thick walls, complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

Supply only integral water proofing compound, complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for RCC 1:2:4 (using 20mm grededstone aggregate) Type B1(Nominal mix) beams and colums as in landings cover slabs(for man holes et) chullah hoods, chajjas,water trughs, mangers,shelves and similar articles with plain faces and set in CM (1:4) complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizonal or slopping) for rough finished flat surfaces of concrete, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsite the premises, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F Factory made 30mm thick flush shutter solid core construction, with MDF and plywood face panels, commercial type on both sides, complete all as specified and as directed.

S & F Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, partitions with extruded built up standerd tubular sectiond/appropriate Z sections and other sectionsapproved make conformunf to IS:1285 fixing with dash fastners of required dia and size includig necessary filling up the gaps at junctions i.e at top, bottom and sides requried EPDM rubber/neoprene filling up the gaps at junction with one or more rebates including joining cleat for fixing etc. aluminium sections shell be smooth, rust free ,straight, mitred and jointed mechanically wherver required including beading gor glazing/paneling complete all as specified complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered. (iii) Cost of all the items, accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, wire cloth shall be measured and paid separately under respective items

S&F 4mm thick frosted/pin headed glass of ordinary quality and glazing for Aluminium Joinery, in squares n.exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F in 4.8 mm thick tinted/dark film sheet glass of ordinary quality nd fixed with aluminium framwork in square in exc 0.5 sqm in each pane completed all as specified and as directed.

S&F in 4.8 mm thick tinted/dark film sheet glass of ordinary quality nd fixed with aluminium framwork in square in n.exc 0.5 sqm in each pane completed all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 150 mm long of extruded section, complete all as specified and as directed.

S&F in repair floor door stopper 150mm (overall length of cover plate) of aluminium alloy body and tongue, anodised, with hard rawn steel spring, fixed in floor, complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

S & F Steel rolling shutters, with out ball bearing, with thickness of laths 1.25mm including top cover, anchoring rod,hasp and staple and one shop coat of primer; erected in position in existing opening gear operated type with bevel gear box and crank handleas indicated, complete: push pull or manual type complete all as specified and as directed.

S & F Ball bearing of suitable sizes complete for rolling shutters complete all as specified and as directed.

S & F Safety lever locks mild steel mild steel with 4 levers including locking plate for rolling shutter shutters complete all as specified and as directed.

S & F as in repair 25mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. with 2 nos socket end caps and brakets(decorative type) complete all as specified and as directed.

Dismantling Dismantling wrought iron or mild steel work of any description not otherwise provided for. complete all as specified and as directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - B] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F mild steel rolled in plates [Fe 410-W (Gde E-250) (plain or chequred] Gusset plate and base plates, square cut or notched (ordinary and counter sunk) forming holes with riveted ,bolted or welded attachemnt,includng welding or riveting etc, complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings), complete all as specified and directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F 15mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, fixed partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, including taking down ,complete all as specified and as directed.

S&F 20mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, including taking down complete all as specified and as directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing, etc., and making good, cutting not exc 10 cm girth, complete all as specified and as directed.

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S&F in repair stop valve fancy type, cast copper alloy, chromium plated, with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repairs Pillar taps with Aerator, fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed.

S&F in repair angale/stop cock, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repair vitreous china Oval shape counter wash basin, 1st quality, white, flat back, approx size 560x410mm excluding taps but including 32 mm bore brass chromium plated including waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed.

S&F in repair brass CP central hole basin mixer for mixing hot & cold water with 450 mm long braided hoses,screwed down for 15mm bore pipe complete all as specified and as directed.

S&F soap dish, any type ,fixed to wall with plugs with chromium plated brass screws, and wooden/plastic cleats complete all as specified and as directed

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide fixed with chromium plated bracket guard and railing 60Cm long fixing, complete all as specified and as directed.

S&F in repairs corner glass self fixed with 5.5 mm thick sheet glass shelf and side not less than 225mm with chromium plated bracket guard for fixing, complete all as specified and as directed.

S&F in repair rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete inclding dismantling of existingall as specified and as directed.

S&F gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and directed.

Taking dowm eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes bends,swan-necks, etc including cleaning or refixing or removal to store (measured overall) as fixed along the centre line over fittings complete all as specified and directed.

S & F repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, fixed in wall with access door complete all as specified and as directed.

S & F repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends (any radius) with and including rubber ring with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) Junction, single (single T) equal or unequal with and including rubber ring joints, complete all as specified and directed.

S&F PVC (SWR) vent cowl, 75 mm bore, complete all as specified and directed.

S & F for 75mm bore of pipe stack clampout of 50mm x 5mm flat iron 16mm dia round iron stay including bolts and nuts and secring ends of stays to wall or roof complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed.

S & F in repair 100mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F in repairs PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of wall care Putty (minimum thickness of two layers shall be 1.50mm) and thereafter applying two or more coats of 100% Premium acrylic emulsion weather coat paint @ 1.43 ltr/10 sqm (for two coats) paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm, complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new Plasterd surfaces of walls duly applied 2mm wall care Putty and there after applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over red oxide complete all as specified and as directed.

M & L for coloured light shade virified Ceramic tiles 10 mm thick (square/ rectangular) of approved size, area of each tile exc 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 20mm thick screed bed in CM (1:6), complete all as specified and as directed.

M & L for coloured light shade virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) of approved size, area of each tile exc 0.18 sqm but not exceeding 0.36 sqm, in skirting/vertical surfaces etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 10mm thick screed bed in CM (1:3), complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:4), complete all as specified and and as directed.

M&L for granite (of any type) 20mm thick (Table rubbled and mirror polished ) in steps, jambs, pillars, window-cills, cooking platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 20mm thick screed bed in CM (1:4), including necessary dismantling of floor tiles complete all as specified and directed.

S & f of 10mm thickness PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling/wall linngincluding Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.including dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S & f of 10mm thickness PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling/wall linngincluding Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. .including dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M & L decorative tupe plaster of paris work of size not less than 50mm x50mm as in cornice or junction of wall and ceiling complete all as specified and directed.

S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteneners 12.5mm dia and 40mm long, including dismantling of wall and ceiling boardscomplete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, including dismantling of wall and ceiling boards complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.(ii) Aluminium frame work shall be measured and paid for separately.

M&L for 20 to 25mm thick Machine cut kota stone slabs as in flooring,treads over & including 20mm thick screed in cm (1:6), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed.

M&L for 20 to 25mm thick Machine cut kota stone slabs as in riser of step, skirting, dado etc. laid over and including 20mm thick backing layer in cm (1:4), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed .

M & L 20mm thick Makrana white marble tiles machine cut in strips, floor laid over 15mm thick cement screed (1:6) and jointed with grey cement slurry including cutting and polishing of type complete all as specified and as directed .

M&L for Plain cement concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregates as in surface channel and drain, complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate), as in sub base of floor/path/ etc. complete all as specified and directed.

M&L for factory fabricated Hydraulically machine pressed cement concrete chequered tiles of size 300x300X25mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM (1:4), tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in separate process in CM (1:3) mixed with pigments to match the colour of the Tiles, complete all as specified and directed.

Taking down Wooden/PVC/Flush shutters exc. 1.00Sqm but n exc2.00 Sqm each, and refing shutter in same opening after easinge etc , complete all as specified and as directed.

M&L for 2nd class hard wood for Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specifiied and directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 30 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and shown on drawing for SI No. 08095 on Srl Page No. 180 of SSR (Part-II) and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,, complete all as specified and shown on drawing for SI No. 08080on Srl Page No. 176 of SSR (Part-II) and as directed.

S&F Galvanised stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.180mm and fixed with tinned tacks, or galvanised wire staples Complete all as specified and as directed.

S&F in repairs Galvanised stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.180mm and fixed with tinned tacks, or galvanised wire staples Complete all as specified and as directed.

S & F Mild steel flat as in hold fast, wall ties plain angle cleat for securing purline to wood trusses and wiremesh confirming to Fe 290 Gde E-165 Complete all as specified and as directed.

M&L for cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

M&L for prelaminated particle board 18/19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete including of dismantling of existing boarding all as specified and as directed.

S & F Hasp and staple, aluminium anodised 100mm safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F 75mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S&F 75 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S & F ball catches with 8mm dia steel ball and brass body and striking plate including letting and fixed complete all as specified and as directed.

S&F in repair sink with drainage board made of 1mm thick sheet of stainless steel (Bronze range super steel 204 : Matt) for kitchen or laboratory with and including plugs, washers, 32mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, also including bedding in cement mortar (1:3) on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mmx 330mm x 160mm complete all as specified and as directed.

S&F in repairs Vitreous China squatting pan orissa pattern size 580x440mm 1st quality, white (excluding flushing cistern & flush pipe) , making connections, complete all as specified and as directed.

S&F in repair vitreous china wash basin, 1st quality, white, flat back, approx size 550x400mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

M & L for Cast iron 100 mm dia for soil, waste and vent pipes in any length with or without ears, jointed with and including cement joints, fixed to walls including necesssary clamps etc complete all as specified and directed.

Except for Cast iron 100 mm dia for soil, waste and vent pipes in any length with or without ears, jointed with and including cement joints, fixed to walls including necesssary clamps etc complete all as specified and directed.

M & L for Cast iron 75 mm dia for soil, waste and vent pipes in any length with or without ears, jointed with and including cement joints, fixed to walls including necesssary clamps etc complete all as specified and directed.

Except for Cast iron 750 mm dia for soil, waste and vent pipes in any length with or without ears, jointed with and including cement joints, fixed to walls including necesssary clamps etc complete all as specified and directed.

S & F CI Branch pieces 100mm bore, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches and fitted with ovel access door complete all as specified and directed.

S & F CI Branch pieces 75mm bore, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches and fitted with ovel access door complete all as specified and directed.

S & F CI bands 75mm bore, fitted with ovel access door complete all as specified and directed.

S & F CI bands 100mm bore, fitted with ovel access door complete all as specified and directed.

S & F CI cowls 75mm bore, fitted with ovel access door complete all as specified and directed.

S & F CI cowls 100mm bore, fitted with ovel access door complete all as specified and directed.

S & F for 100mm bore of pipe Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F for 75mm bore of pipe Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F for 75mm dia cast iron floor/nahani trap with grating including jointing to watse pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F for 100mm dia cast iron floor/nahani trap with grating including jointing to watse pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 40mm bore High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc.complete all as specified and directed.

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints (including Shower Arms) to 15mm bore steel pipe or union, complete all as specified and as directed.

S&F in repair 25mm bore harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

M&L for complete removal of existing treatment from the internal surfaces of wall etc, applying two coats of wall care Putty (minimum thickness of two layers shall be 2mm) and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for complete removal of existing treatment from the old decorated of wall etc, applying two coats of wall care Putty (minimum thickness of two layers shall be 2mm) and thereafter applying two coats of white wash, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparing new plastered surfaces of walls, applying two coats of wall care Putty (minimum thickness of two layers shall be 1.5mm) and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying three coat of white washing, complete all as specified and directed .

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer, complete all as specified and directed.

M&L for preparation of old decorated wall surfaces and applying two coats of cement based paint including brooming down or steel wire brushing down smoke spot,moulds, moss and efforescent and trading oil and greasy spots etc, complete all as specified and directed.

M&L for preparation of old decorated wall surfaces and applying one coats of weather coat acrylic exterior emulsion paint including brooming down or steel wire brushing down smoke spot,moulds, moss and efforescent and trading oil and greasy spots etc, complete all as specified and directed.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

M&L for preparing old wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying one coats of synthetic enamel paint , complete all as specified and directed .

M&L preparation of old painted surfaces of steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed.

S&F hard drawn steel wire fabric (weight not exc.4kg/Sqm) fixed in tank caging, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, complete all as specified and directed.

S & F in 3.15mm dia wire plain steel wire galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and or to straining bolts, including securing with and provision of galvanised iron type wire galvanised iron steples or steel pins, etc , directed (each line wire to be measured separately ), complete all as specified and as directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, depth for manhole etc and getting out in soft/loose soil, complete all as specified and directed.

Excavation over areas, not exceeding 1.5 metre deep in soft/loose soil and getting out, complete all as specified and as directed..

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed.

Removing excavated material to a distance not exc 50.00 mtr and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

M&L for cement concrete (1:4:8) type D-2, using 40mm graded crushed stone aggregates for foundation , filling mass concrete, complete all as specified and as directed

S&F in repair 150 mm bore SGSW pipe, grade 'A', laid in trenches including jointing with cement mortar, complete all as specified and directed. Note:- Excavation & Earth Work, PCC bed & haunching shall be measured & paid for separately.

M&L for cement concrete( 1:4:8) type D-2 using 40mm graded crushed stone aggregates for 150 mm bore pipes as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed.

Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

M&L for point wiring for one light point/ one fan point/ one exhaust fan controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made anodized pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes suitable size and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to for One light /Fan point controlled by one, one way switch match with the adjoining surfaces , complete all as specified and as directed.

All as per item No 150 here-in-before but for one 3pin 5 Amp switch socket outlet, independent board , complete all as specified and as directed.

All as per item No 150 here-in-before but for one 3pin 5 Amp switch socket outlet,same board complete all as specified and as directed.

All as per item No 150 here-in-before but for one 5/15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

S&F Modular switch 1 way 6A, 1 module, complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module, complete all as specified and directed.

S&F Modular socket 6A , 2/3 pin combined, 2 module, complete all as specified and directed.

S&F Modular socket 6A/16A , 2/3 pin combined, 2 module, complete all as specified and directed.

S&F ceiling rose, 3 phase, PVC/ polycarbonate, isolated body, including taking down old unsv ones complete all as specified and directed.

S & F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S & F of surface and wall mounted LED batten 20 watt 4 ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90 total system lumens 1050 Lumens 6500k CRI> 80 Operating Voltage range 140 v-270V incl taking down old unsv complete all as specified and directed.

S & F of surface and wall mounted LED batten 10 watt 2 ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90 total system lumens 2200 Lumens 6500k CRI> 80 Operating Voltage range 140 v-270V incl taking down old unsv complete all as specified and directed.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F TPN, DB, MCB incomer, 4 ways, double door, Metal door , IP-43 IK 09 in 200A rated copper bus bars, earth bar, neutral links, complete including blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and as directed. Make: Cat No 507759 of Legrend/L&T or of equivalent make as mentioned in the Particular Specification Appx 'B' as approved by the GE. Note: Payment of MCCBs & MCBs shall be measured and paid for separately.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN 40/63 Amps current carrying capacity in the DB complete with connection testing and commissioning.complete all as specified as directed.

S&F MCB, TPN, DB, 4 ways, double door, Metal door, IP-43 IK 09 in 100A protection, isolated neutral bar, insulated busbar assembly complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F MCB, SPN, DB, 8 ways, double door, Metal door, IP-43 IK 09 in 100A protection, isolated neutral bar, insulated busbar assembly complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F MCB, SPN, DB, 12 ways, double door, Metal door, IP-43 IK 09 in 100A protection, isolated neutral bar, insulated busbar assembly complete including provision of blanking plates as required & fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repair MCB, SPN 32 amps C series 10ka 240 volts fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repair MCB, SPN 40 amps C series 10ka 240 volts fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repair MCB, TPN 63 amps C series 10ka 415 volts fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repair MCB, SP 6-32 amps C series 10ka 240 volts fixed flush to wall and making good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S & F round shape 15 watt 220 volts AC(white/warm white on requried basis) recessed type with high effciency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as directed and specified.

S & F I repair of Ac short circurit protection motor starter 25 Amps capacity ,230 volt with MCB Dp 25 Amps, plug top & socket complete including taking down old UNSV complete all as directed and specified.

Supply and fix exhaust fan of 250 mm sweep made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaut fan for connection and making suitable size of hole to esiting brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaut fan is deemed to be included in overall rate quoted). complete all as directed and specified.

S & F for energy Exhaust fan of 300 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaut fan for connection and making suitable size of hole to esiting brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaut fan is deemed to be included in overall rate quoted). complete all as directed and specified.

S & F for energy Exhaust fan of 450 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaut fan for connection and making suitable size of hole to esiting brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaut fan is deemed to be included in overall rate quoted). complete all as directed and specified.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as directed and specified.

Material and labour for sub main wiring with 1 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 4 sqmm and 2 single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 4 sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, including taking out the old sub main wiring for connection to DBs /dolly shall be deemed to be includid in this item and shall be measured as one run complete all as specified and as directed. Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 6sqmm and 2 single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 6sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed. Note:- For payment purposes, 3 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

S & F replacement light fitting, 1 X10W LED bulk head luminaries IP65, Min- 50,000 burning Hrs. Diffuser made of high grade polycarbonate. High pressure die cast aluminium housing. CCT-5700K, 240 Volt complete with all accessories and including connection up with twin core twisted flexible copper conductor cabe with suiable size of 230V, 50HZ,complete all as specified and directed.

Supply and fix in repair of ON load manual change over switch 100 Amps 4 pole , I-O-II operational supplied with bridging bars extended shaft and IP65 pistol type handle to be fixed in existing slot of the panel complete all as specified and as directed

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanized steel strip, heavy duty, wire armoured electric LT power cable with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm x 4 core in trenches /along poles/on wall etc and including taking down old one, complete all as specified and as directed

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (Medium grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, including dismantling old unsv ones complete all as specified . Note: GI earth wire 4sqmm dia and 15mm bore protection pipe upto 7.5m from earth plate is deemed to be included in the rate quoted be contrator.

MS ORIENT ENGINEERING WORKS (BID ID -3288333)

M/S B D ENTERPRISE (BID ID -3288701)

M/S JAGRITI ENTERPRISES (BID ID -3288700)

M/S JANATA CONSTRUCTION (BID ID -3288776)

KAMALA INDUSTRIES (BID ID -3289104)

NEO BUILDERS (BID ID -3288865)

M/S TARAN INFRACON (BID ID -3288582)