DEMOLITION AND RE CONSTRUCTION OF BLDG NO 24 NEAR TRANSIT ACCN AT DANAPUR CANTT

Amount

Surface Dressing n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out Soft /loose Soil complete all as specified and directed

M &L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured complete all as specified and directed

M & L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed

M & L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed

Boring holes 3m deep in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50m (dia of pile 300mm)complete all as specified and directed

Excavation in trenches in soft/ loose soil not exc 1.5m wide and not exc 1.5m deep for foundation, pier holes etc n. exc 10sqm on plan and getting out complete.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundation, filling and mass concrete complete.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in foundation, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete all as specified and directed

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in columns, pillars, posts, struts etc complete.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in beams, cantilevers, bressummers, Lintels over 1.5m span etc complete.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete.

Use and waste form work to sides of concrete foundations, footings, bases of columns raft, beam sides and soffits (if any) of foundations & plinth beams and similar wk etc rough finished surface of concrete complete.

Use and wasteform work to sides of pillars, posts, struts, piers, columns stachions flat with rough finished surface of concrete complete.

Use and waste form work to sides of concrete floor or roof beams, beam haunchings, bressummers, lintels, cantilevers, shelves including supports overhangs etc also sprays between floor beams, etc on flat with rough finished surfaces of concrete complete.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cracking, bending, spirally for hopping for columns hookings ends and binding with and incl mild steel wire (annealed) not less the 0.9mm dia or securing with clips complete.

All as per item No 16 but 5 mm dia to 8 mm dia in stirrups, spacers and binders complete.

M&L for old size Brick work with sub- class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 all as spd.

M&L for old size Brick work ( except brick)with sub- class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 all as spd. Note : brick retrived from demolition will be used

M&L 15mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extra cement) complete.

M&L 15mm thick cement plaster on other than fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth (without using extra cement) complete.

M&L rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete.

Supply only water proofing compound (liquid), ISI marked.

M&L hard core of broken bricks of gauge n exc 63mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface all as specified and directed.

M&L100 mm thick cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base including finishing the surface rough & even for receiving kota stone/tiles complete.

M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded stone aggregate as in floors including finishing the surface rough & even for receiving kota stone/tiles complete.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but not exceeding 0.18 sqm in floors etc with and including over 15mm thick screed bed in CM 1:6 set & jointed in neat cement slurry and pointed with white or coloured cement to match complete.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42sqm, in floors and including over 15mm thick screed bed in CM 1:6 set & jointed in neat cement slurry and pointed with white or coloured cement to match complete.

M&L for glazed ceramics coloured tiles of size 450x300x7mm thick as in vertical surfaces such as skirting/dados/wall, etc with and including over 10mm thick rendering in cmeent mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces.

Returning filling in inclunding spreading levelling watering well raming in layers not exceeding 25 cm thick complete all as specified and as directed.

Removing excavated material(soil) exc 50m but n exc 150m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats etc complete all as specified and directed.

S & F 30 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats.

S & F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC frame with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) fixing in opening as per specified & drawing.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawingat site as per specification & drawing all as spd.

S&F factory made uPVC white white colour sliding window area n exc 2 Sqm each. Three track made of extruded profiles with wall thickness of 2.3mm (+/- 0.2 mm). Window profile with hollow section with multi chamber, Frame (88 mm x 52 mm), sliding sash (42 mm x 67 mm), sliding mesh sash (42 mm x 57 mm), sliding interlock (One vertical length in each shutters) (45.5 mm x 28 mm), Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing of hardware and drainage of water etc, making arrangement for fixing of hardware, EPDM gasket, 1.2 +/- 0.2 mm thick galvanised steel Frame (30 mm x 18 mm) 2 nos, sliding sash (30 mm x 18 mm), sliding mesh sash (26 mm x 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners. Hardware: (Touch Lock of Zinc alloyed (white powder coated), steel roller system, Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories.) (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)

S&F factory made uPVC white white colour sliding window area exc 2 Sqm each. Three track made of extruded profiles with wall thickness of 2.3mm (+/- 0.2 mm). Window profile with hollow section with multi chamber, Frame (88 mm x 52 mm), sliding sash (42 mm x 67 mm), sliding mesh sash (42 mm x 57 mm), sliding interlock (One vertical length in each shutters) (45.5 mm x 28 mm), Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing of hardware and drainage of water etc, making arrangement for fixing of hardware, EPDM gasket, 1.2 +/- 0.2 mm thick galvanised steel Frame (30 mm x 18 mm) 2 nos, sliding sash (30 mm x 18 mm), sliding mesh sash (26 mm x 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners. Hardware: (Touch Lock of Zinc alloyed (white powder coated), steel roller system, Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories.) (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)

S&F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165.

S & F pressed steel frame of size 105 X 60 mm and 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc., complete.

S & F pressed steel frame of size 125 X 60 mm and 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc., complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-0 (using 12.50 mm graded stone aggregate), as in back filling of pressed steel frames and similar workd including necessary form work as required complete all as specified and directed.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed.

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long complete all as specified and directed.

S&F mild steel, 150 mm long ordinary helical door spring incl roller and roller plate complete

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F floor door stopper 140 mm overall length of cover plate of aluminium alloy body and tongue, anodised. With hard drawn spring, fixed in floor. complete as directed by Engr-in-charge

S&F small fitings of 2nd class hard wood door, window stops and the like not exc 200 cucm each including MS butt hinges, medium weight, cold rolled 50mm long all as spd.

S&F GI wire cloth 0.56 mm nominal dia of wire andbrick average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified.

S&F in repair 18/19 mm thick Block baords, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, including teak wood lipping, 6 mm thick on sides complete for cupboard shutter and incl shelves all as specified and directed

S&F 100 mm long hasp & staple aluminium anodised wire type, incl bolt to hinge plate and fixed with screw complete.

S&F for mild steel conduit curtain rod with PVC coating fancy type curtain rod 25 mm dia of any colour as approved complete.

S&F mild steel Bracket with PVC coating fancy type for curten rod 25 mm dia of any colour as approved complete.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete.

Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete.

Note for item No 55 to 56 (i) CPVC fittings with brass threading will be measured and paid separately under items No (ii) Cost of normal plain SDR CPVC fittings Like Bend, Tee, Elbow, Union etc shall inclusive under the quoted rate of pipe including.

S&F of CPVC 20 mm Outer dia Brass Elbow complete.

S&F of CPVC 20 mm Outer dia Brass Elbow (3/4 x 1/2) complete.

S&F of CPVC 20 mm Outer dia Brass Tee complete.

S&F of CPVC 20 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

S&F of CPVC 25 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/FBTA) complete.

S&F of CPVC 20 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/FBTA) complete.

S&F of CPVC 25 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

S&F of CPVC 20 mm Outer dia Brass Tank Adoptor complete.

S&F of CPVC 25 mm Outer dia Brass Tank Adoptor complete.

S&F of CPVC 20 mm Outer dia Brass Union complete.

S&F of CPVC 25 mm Outer dia Brass Union complete.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete.

S&F in chromium plated central hole basin mixer single lever without popup waste system with 450 mm long braided hoses complete.

S&F for chromium plated single lever wall mixer 3-in-1 system with provision of both hand shower complete with 115mm long bend pipe, connecting legs and wall flange complete.

S&F for vitreous china wash basin counter shank oval type including PTMT bottle trap but excluding piller tap, etc complete.

S & F for Vitreous china wash down water closet pan ( pedestal pattern ) cascade type of size 365 X 635 X 770 mm coloured with cistern (with twin flush fittings) complete including seat cover and fixing of flushing cistern, brackets, flushing pipe etc, fixed in , complete all as specified and directed (Make : Jaquar cat part no CNS WHT 353N, CNS WHT 203 or equivalent make in Prayag)

S&F for white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F for 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia PVC fixed to wall complete.

S&F for chromium plated health foucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete.

S&F in PVC connection 15mm dia size and 600 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

S&F cabinet mirror, box type of size 19" x 21" of colour as approved fixed to wall complete.

S&F for bib tap 15 mm bore,cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F for CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

S&F for angle cock 15 mm bore cast copper alloy fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F for CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F Corner glass shelf 300mm 3-in 1 (with brass brackets) including fixing arrangements complete. Make-Prayag or equivalent

S&F for stainless steel soap dish, of standard size and shape complete.

S&F in sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers, & waste pipe incl bedding in cement mortar to dwarf wall or incl fixing suitable sizes of cantilever MS brackets and connecting union to pipe overall size 915 x 460 mm, bowl size 410 x 330 x 160 mm complete.

S&F in sinks without drainge board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; & pvc waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete.

S&F for 0.63 mm thick kitchen plate rack made of stainless steel 900 x 750 x 220 mm size fixing with wooden plug with suitable size of screws complete all as specified.

S&F for brass chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed

S&F PVC (SWR) 'P' trap for 110 mm dia etc complete.

S&F for chromium plated toilet paper holder with flap complete. Make- Prayag or equivalent (Cat No BA-08)

M&L for RCC as in kitchen platform, shelves & chajjas etc type B1 1:2:4 (20 mm graded stone aggregate) including necessary form work complete.

M&L for 20 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete.

M&L Machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine including rubbing and polishing incl 10mm thick screed bed in CM 1:4.complete

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

S&F PVC (SWR) pipes 50mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

S&F clamp made out of 50x5 mm Mild steel flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110mm PVC pipe complete.

M&L PVC(SWR) bend of 110mm dia of any radius etc complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia

M&L PVC(SWR) Tee of 110mm dia etc complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 75 mm dia

S&F PVC (SWR) vent cowl 75mm bore

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 1000 Ltr capacity all as spd.

S&F Ball valves 25mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete.

S&F for Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete.

M/L PVC(SWR) bend of 75mm dia of any radius etc complete all as specified and directed

M&L 50 mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete.

M&L for applying two coats of oil bound distemper on plaster surface of wall & concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M & L for preparation of newly plastered surfaces of ceiling and applying 1 mm thick wall care putty including preparation of new surface complete.

M&L for applying two coats of oil bound distemper on plaster surface of ceiling over a coat of primer including, rubbing with sand paper complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete.

M & L for preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete.

M&L for PCC 1:2:4 type B0 (Using 12.50 mm graded stone aggregate) in roof padding/kerbs/sunken slab etc complete all as spd and directed,

M&L 10 mm thick rendering on roof surfaces/concrete surface in CM 1:4 complete.

M&L Water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete

(i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm

(ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces.

(iii) Laying unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

(iv) Applying two coats of bituminous aluminium paint including preparation complete

M&L for vitrified heavy duty (dura stone) tiles 300x300x9 to 10 mm thick in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Construction of Spetic tank for 10 users as shown on Drawing No.CE/TD/2022 /16 dated 16.10.211 complete all as specified and directed.

Construction of Soakage wells 1.2 m dia and 3.0 m effective depth complete as shown on Drawing No.CEJZ/Td?58 sheet 1/1dated 05.05.2000

M & L for concrete bed in P.C.C. 1:4:8 type D2 (using 40mm graded stone aggregated) to drain pipes including packing under and haunching against the sides of the pipes after laying and testing for the following dia of pipes.

(a) 100 mm dia.

(b) 150 mm dia.

M & L for salt glazed stoneware (SGSW) drain pipes grade 'A' laid in trenches and jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed for the following internal dia of pipes.

(a) 100 mm dia.

(b) 150 mm dia.

M & L for plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates as in foundation for manholes, Septic tanks and drains complete all as specified and directed

M & L for plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate), as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L for plain Cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching and surface channel of Manholes complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thicknesses, below or above ground level, complete all as specified.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed

Removing building materials debris (other than excavated material)to distance of 1 km including loading and dumping and leveling at the destination

Dismantling timber scantlings 40 sq. cm and over in section, in any positio, etc complete all as specified.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour dia of PVC conduit pipe 20mm bore including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep for switch, socket with white laminated 3mm thick sheet cover ISI marked with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed for the following :-

(a) One light/ exhaust fan point controlled by one, one way switch 5 Amps

(b) One fan point point controlled by one, one way switch 5 Amps and regulator

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One bell point controlled by one, bell switch 5 Amps

Description all as per item No 142 here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC insulated as earth continuity conductor along with wiring and connecting to the common eath dolly.

Description all as per item No. 142 here in before but using 4.0 sq mm single core copper conductor FRLS cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLS cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular Switch Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for for Bell push modular 6 Amps single module complete all as specified.

S & F for lamp holder , PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed.

S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C complete all as specified and as directed

S & F for Modular type TV Socket out let complete all as specified and as directed.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with multi stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit size 25mm bore of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

S & F for Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of make Bajaj, Havells, HPL complete all as specified and directed

S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 10 watts complete all as specified and as directed. Make Havells /Philips/ Bajaj.

S & F for LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj /Wipro/ Philips/ Bentec.

S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make :- Bajaj, Philips/ Wipro/Havells/ Bentec.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Bajaj/Philips/Havells/CG/Bentec.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make :- Bajaj, Philips, Wipro,Havells, CG.

S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Supply, installation, testing and commissioning of ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, 5 star, BEE 50Hz including electronic fan regulator ISI marked etc and connecting upto ceiling rose/connector with flexible wire as per directed by Engr-in-Charge. Make- Havells /Usha/Crompton Greaves/Bajaj.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper wire upto ceiling rose complete all as specified and directed . Make: Crompton/ Bajaj/Havells/Usha.

Supply and fix electronic energy meters temper proof LCD display with polycarbonate cover three phase, 415 Volts, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time,current reading, load, PF, voltage and KWH complete including necessary accessories as per required.

Supply and fix electric water heater( Geyser) , storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

Supply and fixing of Earthing to panel with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 40 mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete

Supply , laying & testing for XLPE underground cable insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete of size 16 Sqmm nominal cross section x 4.0 core.Make: Havell's/Polycab/Mescab/Gloster

M & L for Excavating in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete. Note: This excavation shall be used for laying of cable.

M & L dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable and gentally hand ramming and consolidation of thickness of sand 18 cm all as specified and directed by Engr - in - Charge. Note :- Sand thickness shall be measured 18 cm only .

M&L for bricks cover of old size bricks sub class 'B' with width equal to the length of the brick laid dry & flet abutted with with each other with gap between adjacent bricks n.exc 10 mm over UG cable for protection compete.

M & L for Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete.

Supply and fixing of GI tubing, light grade, 40 mm bore with all fitting lais in trenches / pole / wall for protection of cables in repairs complete.

M & L for Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

PAPPU ROY CONSTRUCTION

RC GUPTA AND SONS

M/s KUMAR ENTERPRISES

Jai Ambay Construction

M/S NANDA CONSTRUCTION

M/S MODERN CONSTRUCTION

M/S SHEO KUMAR SINGH AND SONS