SPECIAL REPAIR TO BLDG NO P - 106 AT SUB AREA OFFICERS MESS IN ZONE-III AREA UNDER GE (SOUTH) AT JAIPUR MIL STATION

Amount

Demolition of PCC in roof covering. Kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing tratment of any type etc complete all as directed by Engineer - in charge.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0,( 1.2.4) using 12.5 mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement etc complete all as specified and directed.

Supplying & applying fiber reinforced UV resistant elastomeric liquid water proofing &and heat reflective coating with acrilic polymers and polyester /glass fibre after scraping and properly cleaning the surface to remove loose particles with wire brushes complete all over a coat of primer as per manufacturure instructions etc complete all as specified and directed. (Make:- Asian Paint, STP LTD-Shalicry MHI, M/S Sika Cool Coat

S&F UPVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, Type 'B', ISI marked of 110mm bore including taking down of existing pipe etc complete all as specified and directed.

S&F UPVC (SWR) bend of any radius of 110mm bore including taking down of existing pipe etc complete all as specified and directed.

M&L for preparing of old decorated surfaces of (Plastered or unplastered) including cornices pillasters and other wall features and applying two coats of weather based paint of approved shade over wall care putty including scaffolding arrangement, trestles, ladders etc and cleaning of furniture and floors , doors/ windows upto two or three stories etc complete all as specified and directed. Note :- 1.The paint shall be applied by rollers and other finishing tools to ensure smooth surface and consultaion with authorized applicator whereever necessary. 2. Painting shall be done by experts or authorised applicator only.

Taking down door chowkhat or frames with shutters (Without taking off shutters from frame) area n.exc 1.50 Sqm each etc complete all as specified and directed.

Taking down shutters of any description exc 1.00 sqm but n exc 2.00 sqm each etc complete all as specified and directed.

M&L for Cutting holes in stone / brick walls built in CM for inserting hold fast & making good dismantled portion in CM (1:3) depth of embaded portion of holdfast n. exc half brick etc complete all as specified and directed.

M&L 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides face is covered with decorative face veneer with lipping/frame to match etc complete all as specified and directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding etc complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts 200mm long of extruded section etc complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & sliding bolts of extruded sections complete all as specified and as directed

S&F Aluminium handles 150 mm size, cast type, anodised complete all as specified and as directed

S&F aluminium anodised floor door stopper overall length 140 mm double legged with rubber shoe, fixed to bottom rail of door as directed. complete all as specified and as directed .

M&L for Hacking out old broken glass pane (any thickness, size, quality/ description) from metal/wood frame including punching or drilling out old glass panes, pins, springs, clips & providing & fixing new Figured glass 4.0mm thick, pin head type ordinary quality in square not exceeding 1.00 Sqm in each pane. glazed with oil putty etc complete all as specified and directed.

Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and directed.

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing etc complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. etc complete all as specified and directed.

M&L rendering 10 mm thick in CM(1:6) on brick walls or concrdte surface, surface finished even and fair without using extra cement with wpc etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on Brick Walls surfaces or surface other than fair face of brick work of walls, finished even & fair without using extra cement etc complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:4 on concrete surfaces including finished fair & even on ceiling(in small patches and different location also) etc complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade on walls etc complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint of approved shade on walls etc complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade on Ceilling etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed.

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6, finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , on dado vertical surfaces such as in skirting , set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick of cement plaster 1:6, finished even and smooth without using extra etc complete all as specified and directed.

M&L Non skid ceramic coloured tiles 400x400x7 to 8mm thick area of each tile exceeing 0.06 sqm but n.exc 0.18sqm in floors etc set and including 15mm thick layer of screed bed in cm 1:6 on floor surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match the shad of tile complete all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 450x 300 mm both 7mm thick set and jointed in neat cement slurry over and incl 10mm thick rendering in CM 1:4 and pointed in white or coloured cement to match etc complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in cement mortar 1:6 etc complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm , on vertical surfaces such as in skirting & dado set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 etc complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in flooring 100mm thick finished even and fair without using extra cement etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar etc complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished) 20mm thick in flooring over & including 15mm thick screed bed (bedding layer) in CM 1:6, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of Granite including cutting and polishing (half mirror polish i.e. half granite polish as per local trade practice) etc complete all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick, in flooring machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including 15 mm thick screed bed (bedding layer) in CM 1:6 cutting and polishing etc complete all as specified and directed.

M&L for Granite (of any type) tiles 12-18mm thick, in skirting /dado machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including 10mm thich rendering in cement mortar 1:4 cutting and polishing etc complete all as specified and directed.

M & L for RCC 1:2:4 type B1 using 20mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and etc complete all as specified and directed.

Dismantling of loose reinforced cement concrete any description by chieseling , wedging etc. cutting the unserviceable reinforcement as in roofs, floors (including ground floors), beams, staircases, landing, chajjas, slab, similar suspended and columns work complete all as specified and directed incl removal all rubbish material where directed.

Chipping the RCC surface and cleaning the rusted reinforcement and exposed surface by wire brush, mechanical device or any other established method and applying the rust removing solution of approved make and quality with cotton swab to reinforcement and allowing to dry the same for 24 hrs ,brushing of loose particles and applying 1st coat of rust preventive coating of polymer and cement slurry in 1:1.5 proportion with soft brush without adding water including applying another coat of rust preventing after 4 hrs allowing air curing for 48 hrs etc complete all as specified and directed.

S&F false ceiling aluminium snap grid type with hot dipped pre-coated sections & 12mm thick perforated panels mineral finish of grid size 60cmx60cm with following aluminium sections for frame work Including dismantking old False ceilling boards. (a) Wall side angle 19x19mm (cat par No. BPT1945HI) (b) Main tee 32x15mm (cat par No. BP7030102A) (c) Cross tee 32mmx15mm (cat par No. BP7030102A) having integral splices at both ends for interlocking complete with hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

M&L Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 Sq. mm (nominal area), single core, FRLS insulated, PVC insulated and unsheathed stranded cable 1100 volts grade, ISI marked ( IS-694) in and including PVC casing caping, medium grade, ISI marked, with mild steel/PVC modular sunken boxes with earth dolly zink coated and including mounting frame and over cover plate, including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly for followings:- (Note: Cost of hole cutting in wall for bell point, bulk head, building security light and any other site requirement during work execution shall be inclusive in above quoted price. Wiring on stone wall is included in above quoted price.)

(a) One light / fan / bell controlled by one, one way switch.

(b) One 3 pin 5 Amp socket out let on the same board with other switches

(c) One 5 Amp socket independent controlled by one, one way switch.

Description all as per item No 43 here in befor but with 1100 volts grade copper standard conductor cable of size 2.5Sqmm for 3 pin switch socket outlet 15Amp independent board complete all as specified and directed by Engineer in charge .

All as per Item No 43 above but with 4 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 4.0 Sqmm copper cable continuous earth wire and connecting to common earth dolly.

S&F switch modular type single pole one way 15/16 Amp 230 volts etc. complete all as specified and directed.

S&F switch modular type Two Pole, two ways 6 amp rating 230 volts etc. complete all as specified and directed.

S&F switch modular type Two Pole, two ways 6 amp rating 230 volts etc. complete all as specified and directed.

S & F Socket outlet multipurpose modular type 230/250 Volts 2 in 1, 3 pin 5/6 Amp ratings etc. complete all as specified and directed.

S & F Socket Piano type 230/250 Volts 2 in 1, 3 pin 15/16 Amp etc. complete all as specified and directed.

S&F modular Bell push, one way 5 Amp rating etc. complete all as specified and directed.

S&F S&F Electric bell Ding dong type AC 230 volts single pole etc. complete all as specified and directed.

S & F in repair stepped type electronics fan regulator flush type AC 230 volts single pole (ISI marked) for AC 230V, 50 Hz on laminated sheet etc. complete all as specified and directed.

S&F in repair Ceiling rose surface bakelite 65x50mm, 3 Phase/ PVC/ Polycarbonate isolated body (ISI marked) etc. complete all as specified and directed.

S&F lamp holder, angle type, polycarbonate type with back plate suitable for batten fittings etc complete all as specified & directed.

Supply and fix Batten LED light fittings 20/22 Watt, 240 Volt 4 feet size long life surface/wall mounting IP 20 Luminaire per watt maximum extruded aluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre wired twin core twisted flexible copper conductor cable with suitable size. Make: LUMILINMILINEPLUSBS20WLED865SPCSS or equivelent model in Bajaj/Crompton/ Philips as approved by GE

All as per item No 13 here in before, but LED light fitting 1 x 8/10 W ,240 volt( size-2 feet) Make - Siska CAT part No SSK-RA-0801-N or equivelent model in Bajaj/Wipro/ Philips /CG /Surya roshni

Supply & fixing surface mounted LED picture light fitting 7 W LED white, flexible neck for adjusting beam Bronze finish for superior feel long life LED light source, energy saving ,lower power consumption suitable for bathroom, bedroom pre-wired twin core twisted flexible copper conductor cable with suitable size etc complete all as specified and directed. Make : Philips Cat No 31402 or equvalent in Wipro, Syska, CG

Supply & fixing 10 W LED IP -65 Bulkhead environmental friendly, ultra modern, energy saving, surface mounted decorative Hexagon bulk head back lit LED luminaire comprising of high brightness LEDs wall mounted complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size etc complete all as specified and directed. Make - Havells cat No HEXAFT10WLED857SSYMBOPC or equivelent model in Wipro/ Philips/C G

Supply & fix asthetically designed wall mounted synthetic non rechargeable comet wall light (white) with B-22 lamp holder complete including 10 W LED bulb and with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size etc complete all as specified and directed. Make - Philips cat Pt No- 30575 or equvalent in Wipro, Syska, CG

M&L for Sub main wiring with two runs of 6 Sqmm single core FRLS PVC insulated but in unsheathed multi stranded copper conductor cable 1100 volts grade drawn through and including of 25mm dia PVC rigid conduit medium with conduit accessories and fixed to the surface of wall/ceiling as per ISI including 6.0 Sqmm PVC insulated copper conductor earth continuity wire including taking down old etc complete all as specified and directed.

M&L for Sub main wiring with 4 runs of 6 Sqmm single core FRLS PVC insulated but in unsheathed multi stranded copper conductor cable 1100 volts grade drawn through and including of 25mm dia PVC rigid conduit medium with conduit accessories and fixed to the surface of wall/ceiling as per ISI including 6.0 Sqmm PVC insulated copper conductor earth continuity wire including taking down old etc complete all as specified and directed.

S&F Factory made, sheet distribution boards, double door protection class IP-42 suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 r of the under mention rating including taking down old etc complete all as specified and directed. :

TP&N 4 Way

SP&N 8 ways

S&F in repair MCB 10 KA confirming to IS-8828 : 1996, IEC-898 : 1995 rupturing capacity of the under mentioned type and rating :-

(a) SP 5 to 32 amps

(b) TPN 63 Amp

(c) SPN 32 to 63 amps.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.3 mm burried directly in ground (earth pit not less than 2.25 meters deep below normal ground level ), with top edge of the plate not less than 1.5 mtrs below normal ground level , connected to and including galvanised earth strip 25X 4 mm by means of galvanised iron bolts , nut and washers and connected to other end to main panel board duly protected by galvanised iron pipe 25 mm dia " light grage " earth plate surrounded by packed layer of coat dust and common salt 15 cm thick all around bottom and top watering pipe 20 mm bore of galvanised iron " medium grade " with funnel all as shown on electrical plate No 5 of SSR part -I and connecting to earthing testing on completion including cast iron cover frane and PCC 1:3:6 type C-2 using 20 mm grade stone aggregate as in earthing pit with cast iron cover and frame including necessary earth work etc complete all as per specified and directed by Engr-in-Charge . ( Note : PCC Chammer shall be constructed atleast 1.5 mtrs away form the earth electrode of the earth pit and pipe for watering shall be provided in slanting manner).

Supply and fix in repair sheet metal enclosure complete with metallic plug and socket heavy duty moduler type 3 pin (2P + Earth), 32 amp rating single phase 240 volts complete with MCB SP 32 amp “C” series etc complete all as per specified and directed

M & L for Supplying, laying, connecting and testing in trenches, under floors/ roads or on walls Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armored, electric power cables (heavy duty) ISI marked with stranded aluminium conductor, 1100 volts grade, of size 25 sqmm, 4 core including taking out old cable etc complete all as specified and directed

Excavation in trenches n.exc 1.5 metre wide and n.exc 1.5 metre in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes, laying cables errection of poles / struts/stays etc n.exe 10 Sqm on plan not exceeding 1.5 metre in depth and getting out in any type of soil etc complete all as per specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in any type of soil etc complete all as per specified and directed

Removing of excavated material (soil) to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.50metre above the starting point etc complete all as per specified and directed

M & L Sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover etc complete all as per specified and directed

M&L bricks for protection cover to under ground cable (with old size sub class `B` bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm etc complete all as per specified and directed

Schedule of Credit

Deep Construction Company

JAGDAMBA CONSTRUCTION COMPANY

MSR INFRATECH