SPECIAL REPAIRS TO BLDG NO AT-49 OF ARC HAPPY VALLEY AND CERTAIN LBW, REVENUE AND MINOR WORKS AT HAPPY VALEEY UNDER GE SHILLONG

Amount

Dismantling of plain or corrugated steel sheeting any guage thickness including Nainital or similar pattern roof covering complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section in any position (unframed work) complete all as specified and directed.

All as per item No 2.00 here in above but in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and directed.

Dismantling of boarding any description fixed in any position complete all as specified and directed.

Dismantling of wall/ceiling boards of any description (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Taking down Chowkhats or frames exc 1.5 Sqm but n.exc 4 Sqm each but with shutters (without taking off shutters from the frame) including builders hardware each complete all as specified and directed.

Taking down shutters of any description n. exc. 1 Sqm each and removing from site complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces in anyposition including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MD land all specified and directed by Engineer-in-Charge.

Excavation in trenches n exc 1.5 mtr wide and depth n exc 1.5 mtr deep for foundation, etc n exc 10 sqmtr on plan, in soft/loose soil and getting out complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr wide and depth n exc 1.5 mtr deep for foundation, etc n exc 10 sqmtr on plan, in hard/dense and getting out complete all as specified and directed.

Excavation over areas not exceeding 1.5m deep and getting out soft/loose soil complete all as specified and directed.

Excavation over areas not exceeding 1.5m deep and getting out hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in any type of soil complete all as specified and as directed.

Removing excavated materials (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep in soft / loose soil etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Hardcore of crushed stone, gauge n exc 63mm, deposited, spread and levelled well in layers n exc 15cm thick, watered and rammed to a true surface etc complete all as specified and as directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust complete all as specified and as directed by Engineer in Charge.

M&L for RCC 1;1.5:3 type-A1(nominal mix) ( using 20mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like, any thickness above top of footings, including attached pilaster and buttress complete all as specified and as directed by Engineer in Charge.

M&L for RCC type A-1, 1:11/2:3 as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, Canopies, deck slabs and in shelves etc complete all as specified and directed by Engineer-in-Charge.

M&L for Pre-cast RCC 1:2:4 type B1, ( using 20 mm graded stone aggregates) as in cover slab, shelves and similar articles with plain faces and set in cement sand mortar 1:6 including necessary formwork and mould including demolition of old unserviceable one etc complete all as specified and as directed by Engr-in-charge.

Formwork to faces of walls, retaining walls, abutment, parapets and stair case railings and similar work including attached pilasters, buttresses, etc of rough finished surfaces oc concrete vertical ot to batter complete all as specified and as directed by Engineer in Charge.

M & L for Formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landing and similar items(horizontal or sloping) rough finished flat surfaces complete all as specified and as directed by Engineer in Charge.

M&L for Formwork to edges of rough surfaces of concrete flats, treads, breaks in floors,window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed by Engineer in Charge.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed by Engineer in Charge.

S&F mild steel works such as Stairs (framed) including stringers, treades, landing,balusters, hand rails etc. including cleats, brackets, etc and similar work conforming to Fe 410 -W (Gde-E- 250) quality-A etc complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed by Engineer-in-Charge.

M&L for Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts,hooks (stay), heavy, for large gates; hook and pintle hinges:large hasps and staples; chains;hand made sliding bolts; clamps;hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor , foundation filling and mass concrete etc complete all as specified and directed by Engineer in Charge.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor , foundation filling and mass concrete etc complete all as specified and directed by Engineer in Charge.

M&L for PCC (1:2:4) type B2 using 40mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed by Engineer in Charge.

M&L for PCC ( 1:2:4 ) type B-0 ( using 12.5 mm graded crushed stone aggregate) as in coping works, kerbs, lintels up to 1.5m clear span, cills, steps etc including necessary formwork etc complete all as specified and as directed by Engineer-in-Charge.

M&L for 75 mm thick PCC type B-2 , (1:2:4 using 20 mm graded stone aggregates) as in sub base of floor , finishing the cement concrete surfaces even etc complete all as specified and directed by Engineer-in-Charge.

M&L 75mm thick PCC, type C2, (1:3:6, using 40 mm graded stone aggregates) as in floor, hardstanding and plinth protection and finishing the cement concrete surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for PCC( 1:3:6) type C2 (using 40 mm graded stone aggregate) as in surface channel and drains including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc all as specified and directed.

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete (1:3:6) type C1, using 20 mm graded stone aggregate, exc 10 Cm width and setting in cement sand mortar 1:6 complete all as specified and directed.

M&L for RR stone masonry uncoursed, well bonded bedded and solidly hearted setting in cement sand mortar 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints,as specified, of random rubble walling,uncoursed or brought upto courses,hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc 20mm complete all as specified and directed.

M & L for raised pointing in Cement Sand mortar 1:4 to random or polygonal rubble, uncoursed or brought upto courses complete all as specified and directed.

M&L for loose filling with aggregate 40 to 80mm to cover weep holes complete all as specified and directed.

M&L for 2nd class hard wood as in scantling, clean sawn, timber fixed complete all as specified and directed.

M&L 2nd class hard wood plain fillets square rectangular or triangular in section clean sawn secured with nails or brads sectional area exc 3 sqcm n exc 6 sqcm complete all as specified and directed.

S & F of 0.63 mm thick galvanized corrugated iron (CGI) sheeting with two corrugation side lap sheets having zinc coating @ 120 gram per sqm inclusive of both sides, fixed with coach screws/'J' type hook or L type hook and washers as in roof covering etc in any gauge, thickness, including Nainital or similar pattern roof cverings complete all as specified and directed.

Refixing of dismantled galvanized corrugated iron (CGI) sheets fixed with new coach screws/'J' type hook or L type hook and washers as in roof covering etc in any gauge, thickness, including Nainital or similar pattern roof cverings complete all as specified and directed.

S & F 0.63mm thick Plain, galvanised corrugated iron (PGI) sheets, having zinc coating @120gms/sqm as in ridges, hips, valley gutters, drip and straight flashings etc, fixed in any pattern with coach screws or self tapping screws etc complete in any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specifid and as directed.

M&L for Rendering 10 mm thick in cement sand mortar (1:6) on fair faces of concrete surfaces finished even and smooth without using extra cement etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 10 mm thick in cement sand mortar (1:4) on fair faces of concrete surfaces finished even and smooth without using extra cement etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Non Skid coloured Ceramic tiles, joint free, 7 to 8 mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour including screed bed or bedding layer of mortar 15mm thick in cement sand mortar (1:6) for laying floor tiles complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 Sqm nut not exc 1.00 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed

M&L Glazed ceramic colour tiles of size 300x450x7mm /300x600x7 thick in vertical surfaces etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete all as specified and directed.

S & F 2nd class hardwood boarding 40mm thick fixed with nails planed one side with butt joint complete all as specified and directed.

S & F 2nd class hardwood boarding 30mm thick fixed with nails planed one side with butt joint complete all as specified and directed.

S&F 4mm thick Non asbestos fibre cement Bldg Board fixed or laid / inserted to timber frame work with nails as in ceiling complete all as specified and as directed.

S&F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, supplying & fixing in openings as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) considering of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rails on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed togeather with solvent cement, fixing in the frame at site complete all as specified and directed.

M&L for 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood plain framed panelled shutter any number of panels with panels of timber of veneered particle board medium density wood particle board with commercial face veneers; supplied and fitted to chowkats. etc complete all as specified and as directed.

S&F 35 mm thick, 2nd class hard wood, glazed and skeleton shutter, open rebated and prepared to receive glass or gauge without sash bars , divided in to squares and edges of framing plain chamfered or rounded, fitted with cut or mitred beads for securing glass or gauge etc as specified in SSR Part-I section 8 clause 8.24 (a) complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beads etc complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality & glazing with oil putty or fitted with wooden beads in squares n.exc. 0.50 sqm in each pane inluding fixing with wooden beads/glazing pins or spring clips in wooden or metal frames complete all as specified and directed.

S&F 3 mm thick frosted on one side sheet glass ordinary quality & glazing with oil putty or fitted with beads in squares n.exc. 0.50 sqm in each pane inluding fixing with wooden beads/glazing pins or spring clips in wooden or metal frames complete all as specified and directed.

S&F Mild Steel Butt hinges, medium weight, cold rolled, 125 mm size ISI Marked complete all as specified and directed.

S&F Mild Steel Butt hinges, medium weight, cold rolled, 75mm size ISI Marked complete all as specified and directed.

S&F Extruded aluminium anodised bow handles of 150 mm length etc complete all as specified and as directed.

S&F Extruded aluminium anodised bow handles of 100 mm length etc complete all as specified and as directed.

S&F Aluminium anodised, barrel tower bolts of extruded section 100 mm length complete all as specified and as directed.

S&F 250 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and directed.

Taking up or down steel tubing with connections of 15 mm bore pipe including cleaning for refixing or removal from site with all fittings complete all as specified and directed.

Taking up or down steel tubing with connections of 20 mm bore pipe including cleaning for refixing or removal from site with all fittings complete all as specified and directed.

S&F GI tubing 15 mm dia medium grade with all necessary GI fittings, fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F GI tubing 20 mm dia medium grade with all necessary GI fittings, fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F in repairs Vitreous China wash down water closet pan white (pedestal pattern),excluding flushing cistern including plastic water closet seat and making good to disturbed surfaces of floor etc complete all as specfied and directed. Make:- Prayag Cat Part No. 4125 or equivalent make of Jaguar/ Parryware / Hindware/Cera.

S&F in repair PVC (Plastic polymer flushing Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as directed by Engineer-in-Charge .Make:- Prayag cat aprt no. 503 or equivalent make of Pearl/ Hindware.

S&F in repair Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat aprt no. 4645 IRIS or equivalent make of Pearl/ Hindware.

S&F in repair kitchen sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm ,bowl size 410 mm x 360 mm x 160 mm complete all as specified and directed.Make:- Prayag / Nirali / Hindware

S&F in repairs CP Bib tap 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.7606 or equivalent model from make:Cera/Jaguar/Parryware

S&F in repair Pillar tap,15 mm bore, brass chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge Make:- Prayag cat part no.7602 or equivalent make Hindware / Sona.

S&F in repairs CP Stop cock ( concealed type) ,15 mm bore, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.9218 or equivalent model from make Sona / Hindware.

S & F in repair CP grating doom 150 mm dia complete all as specified and as directed.

S&F in repair PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 as in Concrete bed to 150 mm drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and as directed.

Cutting into existing manholes for connecting new pipe, cutting out existing benching and forming branch channel (1/2 round or 3/4 section) in cement concrete type B1 ( 1:2:4, using 20mm graded crushed stone aggregates), finished and reforming benching as required for internal dia of pipe 160 mm etc complete all as specified and as directed by Engineer in charge.

S&F Low Density Ploythene Pipes (LDPE) dia 40mm of pressure rating 6kgf/Sqcm fixed to walls, ceilings or in floors etc complete all as specified and directed.

S&F110 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed.Make:- Prince / supreme.

S&F 110mm bore PVC (SWR) bends /door bend of any radius with cement solvent, cement joints, complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110mm dia complete all as specified and as directed.

S&F PVC gutter , Half round 180mm size fixed on support brackets at any height complete all as specified and as directed.

S&F Joint Bracket (with 2 clamps), 180mm for PVC pipes (Half round) complete all as specified and as directed.

S&F support Bracket 180mm for PVC pipes (Half round) complete all as specified and as directed.

S&F running outlet (with 2 clamps) 180mm for PVC pipes (Half round) complete all as specified and as directed.

S&F stop end outlet (with 1 clamp) 180mm for PVC pipes (Half round) complete all as specified and as directed.

S&F PVC reducer 180mmx110mm complete all as specified and as directed.

S&F 150mm salt glazed stone ware (SGSW) pipes grade 'A' laid in trenches and jointed as specified complete all as specified and directed by Engineer-in-Charge.

S&F 450mm bore reinforced concrete pipes, class NP2(ISI Marked) embosing with date of manufacturing, laid and jointed with CM (1:3) complete all as specified and directed by Engineer-in-Charge.

M&L for Sand filling under floor including watering and well ramming for laying of interlocking paver blocks and cushioning to UG cables complete all as specified and directed by Engineer-in-Charge.

M&L for Machine pressed pre-cast concrete polished rubber moulded coloured interlocking paver block of any shape and size conforming to IS : 15658-2006 , 80 mm thickness, M-40 grade of approved design jointed with grey cement and pigment etc complete all as specified and as directed.

M&L for Synthetic enamel paint one coat on old wooden surfaces over 10 Cm width or girth including necessary preparation of wooden surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old painted wooden surfaces of any description n.exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old surfaces of wall and applying two coats of acrylic distember over a coat of alkali resistant priming paint complete all as specified and as directed by Engineer-in-Charge.

M&L for Synthetic enamel paint two coats over a coat of red oxide primer on new or previously untreated steel surfaces exc.10 Cm width or girth including necessary preparation of steel surfaces etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces of steel of any description and girth, not otherwise described and treated with one coat synthetic enamel paints complete all as specified and directed.

M&L for complete removal of existing treatment of walls, preparing the surfaces and applying two coats of weather proof paint (Exterior grade) over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered external surfaces of walls, and applying two coats of weather proof paint (Exterior grade) over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of white or tinned cement base paint over a coat of wall primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered surfaces of ceiling including cornices, plasters etc and applying two coat of white wash complete all as specified and directed.

M&L for preparation of old painted steel roof surfaces of CGI sheet, over 10cm in width or girth and applying one coat of synthetic ename roof paint complete all as specified and directed.

M&L for French polishing on surface of any description, width or grit including cleaning and preparation the surface including a coat of wood filler with two or more coats all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, lamp holders, regulators, switch, socket outlets, bell push, ceiling rose etc , removing material to store for keeping in safe custody for reuse at site and making good to disturbed surfaces of walls with cement sand mortar (1:6) and white/colour wash to match with existing surfaces etc complete all as directed.

M&L Point wiring with single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked) as continuous earth wire terminated in and including sunken box for following type of point wiring including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge for one light point / one fan point etc on independent board controlled by one one way switch etc complete all as specified and as directed.

All as per item No 113.00 above but for one 2/3 pin socket outlet 5/6 Amps point on same board etc complete all as specified and directed.

All as per item No 113.00 above but for one 2/3 pin socket outlet 5/6 Amps point on independent board etc complete all as specified and directed.

All as per Item No. 113.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

S&F lamp holder, insulated body, with back plate for batten fitting complete all as specified and directed.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

Supply and fix Socket (ISI marked), 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed.

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed.

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 5/15 Amps, flush type, 240 volts complete all as specified and as directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5 Amps complete all as specified and directed.

Supply and fixing in repair LED batten fittings 1x18/20 Watt complete pre wired fixed to wall with 2 nos PVC block of suitable size etc complete all as specified and as directed. Make Bajaj Cat Part No BCLSB 18 WH or crompton cat part no LCTL- 20-CDL or equivalent make of Philips / Havells.

S & F in repair wall mounted LED batten fittings with all accessories 1X 9/10 Watt LED 6000K , extruded polycarbonate, integrated electronic driver and fixed to wall with 2 Nos PVC block suitable size complete all as specified and as directed .Make Bajaj Cat Part No BCLSB 10 NW or Cropmpton Greaves Cat Part No-LCTL-10-CDL equivalent make of Philips / Havells.

S & F in repairs Exhaust fan 230 volts , 250mm sweep ,plastic body including making all electric connection including cutting of hole on brick or block wall and making good disturbed to disturbed surface of wall with cement sand plaster (1:4) and painted / colour wash to match the existing to the true satisfaction of Engineer in charge, necessary and outer wooden box for fan fix on wall etc complete all as specified and as directed. Make :- Havells cat part no. ventil air DX White or equivalent make of Bajaj / Philips. Note : Old Unserviceable Exhaust fan obtained from taking down should be deposited in MES Store

Supply and fix in repair MCCB four pole , 415 Volt, 63 Amps,25 KA rupturing capacity , adjustable thermal & fixed magnetic setting complete all as specified and directed.Make: Havells Cat Part No-IHLGNF0063 or equivalent make of Schnieder / GE / C&S / Indoasian / L&T / Legrand.

S&F in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with necessary electrical connection complete all as specified and directed . Make: Havells Cat Part No-DHDPSHODRW08 or equivalent make of Legrand / Schneider /L&T

Supply and fix in repair MCCB Distribution board, TP&N , vertical , double door, 50 Hz with IP-43 protection,sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link,415 Volts 4 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Havells Cat Part No-DHLDVDRWGOFO04 or equivalent make of Schnieder/GE/C&S.

S&F in repair MCB SP, 240 Volt, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed .Make:- Havells cat part no.DHMGCSPF040 or equivalent model from make:- Hager/Schneider / Siemens / Legrand / Indo Asian .

S&F in repair MCB SPN, 240 Volt, 6-32 Amps 10kA rupturing capacity 'C' series AC fixed in DB's complete all as specified and directed .Make:- Havells Cat Part No-DHMGCSNF006 or equivalent make of Hager/Schneider / Siemens / Legrand / Indo Asian .

S&F in repair MCB SP, 240 Volt, 6-32 Amps fixed in DB's complete all as specified and directed .Make:- Havells Cat Part No - DHMGCSFPOO6 or Schneider cat part no.A9N4P32C or Indo asian Cat Part No-81195or Hager cat part No.NCN106N

Material and labour for sub main wiring with two single core 4.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 4.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed, including taking down unservicable one.(Note: two run of 4.0 sqmm cable , one run of earth wire of 4.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR kabel/Havells/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including taking down old underviceable and necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I complete all as specified and as directed.

S & F in repairs LED lamp 7 Watt B22 base colour Temp 6500K complete all as specified and directed. Make Havells/ Philips/Bajaj

S&F in repair bulk head luminaries with all accessories 10 W LED energy saving with opal diffuser including necessary connectioncomplete all as specified and directed. Make Havells Cat Part No-RUGBYNEONFT10WLED860SSYMOPC or Bajaj Cat Part No-BIBWP10WLED or equivalent make of Philips

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 16Sqmm 4.0 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed including taking down old unserviceable one etc complete all as specified and as directed.

Supply and laying Sub class 'B' well burnt fly ash brick, laid flat in trenches as protection to XLPE cable complete all as specified and as directed.

S&F in repair GI tubing 25 mm dia light grade with all necessary GI fittings, laid under road/floor, fixed on pole/wall with necessary clamp or hook for cable protection complete all as specified and as directed.

M/S UTTAM SAHA