WBPW(R)D/NIT- 26 of SE/WHC-I/2025-2026/6

PART-A: ROAD WORKS

Picking up and removing old bituminous layer or sand sealing coat from old black topped surface and cleaning the exposed surface by scraping and stacking the material as directed. By mechanical means (Without milling machine): From 50 mm to 100 mm thick.

Box cutting or filling in Road embankment in all sorts of soil including spreading the spoils properly over the flank as necessary or on berm to approximate grade & camber and rolling the sub-grade with power roller to proper camber and grade as per direction and satisfaction of Engineer-in-charge including uprooting and removing plants and jungles when and where necessary. Depth upto 900 mm.

Supplying, spreading and compacting Medium Sand to required thickness, in layers not exceeding 150 mm to proper gradient and camber, inundating each layer by water and packing and ramming layer by layer to achieve desired compaction, including lighting, guarding, barricading and making adequate earthen bundh where necessary, curing with water as per direction, mending cracks and depressions by ramming wherever necessary. The compaction factor for dry, clean sand may be taken as 0.835. (The payment is to be made on the basis of the finished compacted volume.)

Construction of granular sub-base by providing graded material, mixing in Wet Mix Plant at OMC, carriage of mixed material to work site, spreading in uniform layers with Motor graderon prepared surface in proper grade and camber, compacting with vibratory power roller to achieve the desired density, including lighting, guarding, barricading, including cost of all materials, machinery, tools and plants and cost of quality control complete as per Clause 401 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). Grading – II Tentative materials required per m³ of compacted volume: 37.5 mm aggregates @ 0.1920 m³/m³, 22.4 mm aggregates @ 0.1280 m³/m³, 11.2 mm aggregates @ 0.1280 m³/m³, 5.6 mm aggregates @ 0.1536 m³/m³ & sand @ 0.6784 m³/m³.

Construction of granular sub-base by providing graded material, mixing in Wet Mix Plant at OMC, carriage of mixed material to work site, spreading in uniform layers with Motor graderon prepared surface in proper grade and camber, compacting with vibratory power roller to achieve the desired density, including lighting, guarding, barricading, including cost of all materials, machinery, tools and plants and cost of quality control complete as per Clause 401 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). Grading – III Tentative materials required per m³ of compacted volume: 26.5 mm. aggregates @ 0.4480 m³/m³, 5.6 mm aggregates @ 0.5760 m³/m³ & sand @ 0.2560 m³/m³.

Wet Mix Macadam Base Course Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including screening of aggregates and granular materials, premixing the material with water at OMC in Wet Mix Plant, carriage of mixed material by tipper to site, laying in uniform layers with Paver in Sub- base / Base course on well prepared surface and compacting with Vibratory Roller to achieve the desired density, including supply of all materials, machinery, fuel and lubricants, including incidental costs for lighting, guarding, barricading, making earthen bundh to protect the edges including cost of quality control complete as per Clause 406 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). Tentative materials required per m³ of compacted volume: 26.5 mm aggregates @ 0.3960 m³/m³, 13.2 mm aggregates @ 0.2640 m³/m³, 5.6 mm aggregates @ 0.3564 m³/m³ & Stone dust @ 0.3036 m³/m³.

Providing and applying primer coat with Cationic Bitumen Emulsion of approved grade conforming to IS: 8887-1978 and requisite quantity on prepared surface of granular base including cleaning of road surface and spraying primer using Mechanical means including cost and carriage of bitumen emulsion and all other incidental costs of work complete as per Clause 502 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). For WBM / WMM Surface: Using Cationic Bitumen Emulsion (S.S.-I grade bulk) @ 0.85 Kg./m²

Supplying & providing and applying tack coat with Cationic Bitumen Emulsion of approved grade conforming to IS: 8887-1978 on the prepared surface cleaned with Hydraulic broom, moistening the surface including cost and carriage of emulsion, hire charges of machinery and labour, cost of fuel and lubricants all complete as per Clause 503 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). On Granular surfaces treated with primer Using Cationic Bitumen Emulsion (R.S.-I grade bulk) @ 0.275 Kg./m²

Supplying & providing and applying tack coat with Cationic Bitumen Emulsion of approved grade conforming to IS: 8887-1978 on the prepared surface cleaned with Hydraulic broom, moistening the surface including cost and carriage of emulsion, hire charges of machinery and labour, cost of fuel and lubricants all complete as per Clause 503 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). On Bituminous Surface. Using Cationic Bitumen Emulsion (R.S.-I grade bulk) @ 0.250 Kg./m²

Providing and laying dense bituminous macadam with Hot Mix Plant using crushed aggregate of specified grading, filler (Cement/Hydrated lime/Rock dust) premixed with bituminous binder of approved grade @ 4.0% (min) for Grading-1 and 4.5% (min) for Grading-2 by weight of total mix as per table 500-10 and mix design done as per table 500-11 and Job Mix Formula as per clause 505.3.3 of MORT&H (5th Revision), including screening, cleaning of chips, transporting the hot mix to work site, laying the mixed materials at specified laying temperature, as specified in Table 500-2 with a hydrostatic paver finisher with sensor control to the required grade, level and alignment over prepaired surface coated with tack coat, rolling with smooth wheeled and vibratory or tandem rollers or with a pneumatic tyre roller of 12 to 15 tonne weight with a tyre pressure of at least 0.56mpa, to achieve the desired density as per clause 505.3.5, all including cost and carriage of bitumen, crushed aggregates, filler materials and hire charges of machinery and equipment for construction and quality control complete as per Clause 505 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). Excluding cost of applying tack coat using cationic bitumen emulsion. For Grading 2 (26.5 mm nominal size, 50-75 mm thick. Using Batch Type HMP of minimum capacity 100-120 TPH. Tentative stone materials required per m³ of compacted volume: 26.5 mm size chips @ 0.2197 m³/m³, 22.4mm size chips @ 0.2197 m³/m³, 11.2mm size chips @ 0.3662 m³/m³, 5.6mm size chips @ 0.2197 m³/m³, stone dust with grit @ 0.4394m³/m³, Hydrated Lime @ 44.00 Kg/m³& Bulk bitumen (VG-40 bulk) @ 111.00 Kg./m³

Providing and laying bituminous concrete with Hot Mix Plant using crushed aggregates, filler materials (Cement/Hydrated lime/Rock dust) and premixed with bituminous binder of specified grading @ 5.2% (min) for Grading-1 and @ 5.4% (min) for Grading-2 as per table 500-17 and mix design done as per table 500-10 and Job Mix Formula as per clause 505.3.3, including screening, cleaning of chips and preparing a uniform and quality mix, transporting the hot mix to work site, laying the mixed materials at specified laying temperature, as specified in Table 500-2 with a hydrostatic paver finisher with sensor control to the required grade, level and alignment over prepaired surface coated with tack coat, rolling with smooth wheeled and vibratory or tandem rollers or with a pneumatic tyre roller of 12 to 15 tonne weight with a tyre pressure of at least 0.56mpa, to achieve the desired density as per clause 505.3.5, including cost and carriage of bitumen, crushed aggregates, filler materials and hire charges of machinery and equipment for construction and quality control complete as per Clause 507 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). Excluding cost of applying tack coat using cationic bitumen emulsion. For Grading 2. (13.2 mm nominal size, 30-40 mm thick.) Using Batch Type HMP of minimum capacity 100-120 TPH. Tentative stone materials required per m³ of compacted volume: 13.2 mm size chips @ 0.2959 m³/m³, 11.2mm size chips @ 0.2959 m³/m³, 5.6 mm size chips @ 0.2959 m³/m³, stone dust with grit @ 0.5919 m³/m³, Hydrated Lime @ 45.00 Kg/m³ & Bulk bitumen (VG-40) @ 137.00 Kg./m³

Supplying and laying in the specified pattern if interlocking concrete Block pavement (ICBP) with concrete blocks (with concrete grade as specified as per Tablel as IS 15658:2006) manufactured in steel mould clamed to a vibrating table by hydraulic pressure (as per cl. no. 6.30 of IRC:SP:63 (2018), from BIS licensee manufactured, with spacer nib (small protruding profiles on the vertical face of apaver block used as a device for keeping minimum joint gap in between the paving blockes , as per cl. no. 3.26 of IS: 15658) and of specied size and shape with aspect ration(the ratio of length to thickness of a paver block, as per cl. no. 3.3 of IS:15658) as per Table 2 of IS:15658 with flexural strength/breaking load as per Annexure G of IS:15658, on the prepared base course of specified CBR as table 1 of IRC SP 63 (2018) or else as mentioned in design and drawing with a caushin of compacted bedding sand of 25-35 mm thick (grading of the bedding sand as per clause 6.5.1 of IRC SP-63) and filling up the gaps in between paver blocks with joint filling sand (the grading of the edge with cut blocks as per cl. no. 8.7 of IRC SP-63 (2018) with compaction, levelling and filling up of the edge gap. 120mm thick. Grey.

Plain Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement complete as per drawing and technical specifications. PCC Grade M30. Using Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Construction of Embankment with Material Deposited from Roadway Cutting. Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 for Rural Roads of MORD including carriage of material for a distance of 1 km.

Construction of Sub Base using Local Materials, spreading in uniform layers with Motor grader on prepared surface, including screening the metal as necessary, mixing by mix in place method with Rotavator at OMC, and compacting with vibratory roller to achieve the desired density, lighting, guarding and barricading including cost and carriage of all materials and making necessary earthen bundh of one metre wide on each side to protect the edges complete as per Clause 401 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). For Construction of Sub Base by compacting stone chips and sand (in proportion of 40:60). Using Salvage Material.

Water Bound Macadam Sub Base by consolidating Jhama Metals of specific size in hard crust to requisite thickness (measured after compaction) in layers including screening of metals etc. as necessary, hand packing, sweeping, watering and rolling in stages with power roller to proper line, grade and camber, lighting, guarding & barricading and making necessary earthen bundh of one metre width on each side where necessary to protect edges and preparing the bed by necessary cutting or filling and rolling all complete including the cost of all materials and hire and labour charges of all men and machineries and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). (i) For Construction of Sub Base by consolidating Jhama metal (63 mm to 45 mm) with moorum screening : For Hard Shoulder with fresh Jhama Materials. Using 0.26 m³ moorum /1.09 m³ of Jhama metal. (Payment is to be made on the basis of finished compacted volume of work.)

PART-B: ROAD FURNITURE

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete as per Clause 803 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc. Ordinary kilometer stone

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc. 5th kilometre stone

Supplying fitting and fixing R.C. guard post 1.37m long with C.C. 1:2:4 with graded stone chips of 13.2mm down casting , curing complete including cost of providing 4nos.of 12mm dia. rod of length 1.54m as main reinforcement and 6 nos. of round shaped 8mm dia rods used as binders; the placing of the first binder should be at 75mm below the top finished surface and the other 5 nos of binders should be placed at 245mm c/c ; the guard post is of octagonal section with inscribed circle of dia 24cm at the base tapering to corresponding dimensions of 16cm at the top including two coats of painting with best quality synthetic enamel paint of approved make and grade to form 6 nos. horizontal alternate bands in white/tannery yellow and black to 90 cm length standing up above ground after mending good damages if any during striking off shuttering, making hole in ground of 47cm depth and 30cm. minimum dia, fixing the guard posts in the same holes and repacking the earth properly so as to keep the guard posts standing properly erect in correct position true to line and length including carriage of R. C. Guard Post with due care to the site including loading into the truck and unloading at site complete in all respect. With Pakur variety stone chips.

Type - A, "W" : Metal Beam Crash Barrier Supplying & providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanized by hot dip process, all fittings to conform to IS:1367 andIS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per Clause 811.3 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).

Supplying & fixing of Raised pavement Markers/Road Studs/Cats eye made of polycarbonate moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face which shall support a load of 13635 kg tested in accordance to ASTM D 4280 Type H and complying to clause no 804 of MoRT& H’s specification for Road & Bridge works (Fifth Rev.). Marker height shall not be less than 10mm and shall not exceed 20mm, width shall not exceed 130 mm and with minimum reflective area of 13 sq.cm on each side and slope to the base shall be 35 ± 5 degre. Fixing will be without nails but by using epoxy resin based adhesive as per manufacturer’s recommendation including site clearance etc. and complete as directed by the Engineer in Charge. The contractor will have to provide a test certificate from a reputable national/ international laboratory conforming the above specifications.

Supplying & providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing and Clause 801 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).

Direction and Place Identification Signs with size more than 0.9 sqm size Board. Supplying & providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing and Clause 801 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing and Clause 801 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). 90 cm equilateral triangle

60 cm circular

80 cm x 60 cm rectangular

90 cm High Octagon

PART-C: CROSS DRAINAGE WORKS (05 NOS-BOX CULVERT 2X2)

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202 for Rural Roads of MORD. Above 600 mm to 900 mm

Dismantling of existing structures like culverts, bridges, retaining walls and other structures comprising of brick masonry, including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 m as per Technical Specifications Clause 202 for Rural Roads of MORD. Brick work with Cement mortar.

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specifications Clause 202 for Rural Roads of MORD. By Mechanical Means Reinforced Cement Concrete

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, removing, spreading or stacking of spoils within a lead of 150 m. as directed and including trimming the sides of the trenches, leveling, dressing and ramming the bottom, and backfilling with approved material complete as per direction of the Engineer-in-Charge . In Marshy soil for depth upto 3 m depth B By Mechanical Means using excavator of suitable capacity and tipper trucks. (i) With pumping out water including shoring as required.

Fine Sand filling in foundation trenches and at the back of abutments, wing-walls etc. with good local sand free from earth in layers not exceeding 15 cm. including inundating each layer by profuse water and poking and ramming layer by layer complete including supply of sand. Quality of sand is to be approved by the Engineer-in-charge. The compaction factor for dry, clean sand may be taken as 0.835. (The payment is to be made on the basis of the finished compacted volume.)

Brick soling with picked jhama bricks including preparation of bed as necessary with brick joints properly filled in and packed with local sand and including necessary cushion of similar material below the soling (and in between layers when more than one layer is used) completes as per direction.Single brick flat soling (thickness 75 mm.)

Supplying, Providing and laying Design Mix concrete for plain /reinforced concrete work in any part of bridge (excluding bottom plugging) with coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete but excluding cost of labour and materials for formwork & reinforcement works. M-15 Grade Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Curtain wall complete as per drawing and Technical specification Cement concrete Grade M15

Plain / Reinforced Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement complete as per drawing and technical specifications. RCC Grade M25 Using Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Plain / Reinforced Cement Concrete in Substructure with coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality, cement and water reducing admixtures, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete as per drawing and technical specification including the cost of necessary form work and staging complete as per drawing and technical specifications. RCC Grade M25 Height upto 5m Using Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Plain Cement Concrete in Substructure with coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality, cement and water reducing admixtures, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete as per drawing and technical specification including the cost of necessary form work and staging complete as per drawing and technical specifications. PCC Grade M20. Height upto 5m Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Hire and labour charges for Shuttering with or without staging upto 4.0 m height using approved stout props with wooden planks/ply wood/steel sheet plate with required bracing for any kind of plain or reinforced concrete works in all sorts of minor structure including culvert, box culvert, crossdrain etc. The rate is inclusive of fitting, fixing and striking out after completion of work as per specification and direction. Where staging is not required.

Supplying, fitting and placing un-coated HYSD bar reinforcement in Bridge Foundation including initial straightening, straightening of coils bars, removal of loose rust (if any), cutting to requisite length bending, binding with annealed wire not less than 1 mm in size and conforming to IS 280 at every intersection hooked and bent to correct shape and placed on forms etc. including cost of black annealed wire and cost of loading, unloading, carriage of all steel materials complete as per drawing and technical specifications and direction of Engineer-in-charge. Tor Steel rods / HYSD bars / TMT (Sail/Tata/ Rinl) (Fe 415 /Fe 500 /Fe 500D, conforms to IS: 1786 latest revision)

Supplying, fitting and placing HYSD bar reinforcement in Sub-structure including initial straightening, straightening of coils bars, removal of loose rust (if any), cutting to requisite length bending, binding with annealed wire not less than 1 mm in size and conforming to IS 280 at every intersection hooked and bent to correct shape and placed on forms etc. including cost of black annealed wire and cost of loading, unloading, carriage of all steel materials complete as per drawing and technical specifications and direction of Engineer-in-charge. Tor Steel rods / HYSD bars / TMT (Sail/Tata/ Rinl) (Fe 415 /Fe 500 /Fe 500D, conforms to IS: 1786 latest revision)

Flexible Apron Construction of flexible apron 1 m thick comprising of loose stone boulders weighing not less than 40 kg beyond curtain wall.

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (a) One Coat Water based interior grade Acrylic Primer

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. Including using of approved putty etc. on the surface, if necessary : On timber or plastered surface : With super gloss (hi-gloss) -Two coats (white in shade)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. Including using of approved putty etc. on the surface, if necessary : On timber or plastered surface : With super gloss (hi-gloss) -Two coats (with any shade except white)

Construction of precast RCC railing of M30 Grade, aggregate size not exceeding 12mm, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertical post for expansion, complete as per MoRT&H standard drawing no SD/202 and technical specifications.

Providing weep holes in Brick masonry / Plain / Reinforced concrete abutment, wing wall / return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical specifications.

Drainage Spouts in Superstructure including providing drip mouldings and also including supplying, fitting and fixing approved type of materials complete as per drawing and Technical specification vide clause no. 2705 of MoRT&H’s Specification for Road & Bridge Works.

Supplying, Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification. Usingf 0.72 m³ of brick aggregates and 0.48 m³ of coarse sand (loose volume) per m³

Supplying, Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications. Cement Concrete Blocks of size 0.3x0.3 x0.3 m cast in cement concrete of Grade M15

PART-D: DIVERSION WORK

Construction of embankment with approved material obtained from borrow pits land owned/arranged by the agency at his own cost with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 for Rural Roads of MORD. (Mode of measurement: pre works and post works) Carriage up to total lead of 3.0 km. (Royalty charge on earth @ Rs. 29.00 /m³ and cesses charges @ 5.30 /m³ will be deducted from the bill amount if the contractor not able to produce necessary documents in support of payment made towards the royalties).

Brick soling with picked jhama bricks including preparation of bed as necessary with brick joints properly filled in and packed with local sand and including necessary cushion of similar material below the soling (and in between layers when more than one layer is used) completes as per direction.Single brick flat soling (thickness 75 mm.)

Construction of Sub Base using Local Materials, spreading in uniform layers with Motor grader on prepared surface, including screening the metal as necessary, mixing by mix in place method with Rotavator at OMC, and compacting with vibratory roller to achieve the desired density, lighting, guarding and barricading including cost and carriage of all materials and making necessary earthen bundh of one metre wide on each side to protect the edges complete as per Clause 401 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). For Construction of Sub Base by compacting brick aggregates (40 mm down) and sand (in proportion of 60:40). Using brick aggregates (40 mm down) @ 0.90m³/m³ and medium sand @ 0.48 m³/m³.

Water Bound Macadam Sub Base by consolidating Jhama Metals of specific size in hard crust to requisite thickness (measured after compaction) in layers including screening of metals etc. as necessary, hand packing, sweeping, watering and rolling in stages with power roller to proper line, grade and camber, lighting, guarding & barricading and making necessary earthen bundh of one metre width on each side where necessary to protect edges and preparing the bed by necessary cutting or filling and rolling all complete including the cost of all materials and hire and labour charges of all men and machineries and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). (i) For Construction of Sub Base by consolidating Jhama metal (63 mm to 45 mm) with moorum screening : For Hard Shoulder with fresh Jhama Materials. Using 0.26 m³ moorum /1.09 m³ of Jhama metal. (Payment is to be made on the basis of finished compacted volume of work.)

PART-D: PROTECTIVE WORKS

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, removing, spreading or stacking of spoils within a lead of 150 m. as directed and including trimming the sides of the trenches, leveling, dressing and ramming the bottom, and backfilling with approved material complete as per direction of the Engineer-in-Charge . In all sorts of soil excluding marshy soil & rocks (soft or hard) by manual means. a) upto 3 m depth Without pumping out water including shoring as required.

Filling properly the empty sausage crates with boulders of any size & shape with hand packing after preparation of bed of placement, placing the crate in position, carriage of boulders from road stacks with a lead upto 150m etc. complete in all respect including stitching the rest of the crate with wire (passage for filling boulders) after filling up the crate with boulders and launching the crate in position if necessary and as directed by the Engineer-in charge. Using 30/45 kg Stone Boulder.

Weaving wire mattress as directed with wire of 4mm dia. and making sausage crate of required shape after tying all intersections including joining longitudinal ends, closing ends of sausage, carriage of wire to site of work complete in all respect as per direction of the Engineer-in-charge including cost of supply of G.I. wire. (With 100mm x 100mm mesh.)

Plain Cement Concrete in Substructure with coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality, cement and water reducing admixtures, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete as per drawing and technical specification including the cost of necessary form work and staging complete as per drawing and technical specifications. PCC Grade M20. Height upto 5m Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, removing, spreading or stacking of spoils within a lead of 150 m. as directed and including trimming the sides of the trenches, leveling, dressing and ramming the bottom, and backfilling with approved material complete as per direction of the Engineer-in-Charge . I. In all sorts of soil excluding marshy soil & rocks (soft or hard) by manual means. a) upto 3 m depth (i) With pumping out water including shoring as required.

Brick soling with picked jhama bricks including preparation of bed as necessary with brick joints properly filled in and packed with local sand and including necessary cushion of similar material below the soling (and in between layers when more than one layer is used) completes as per direction.Single brick flat soling (thickness 75 mm.)

Plain Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement complete as per drawing and technical specifications. PCC Grade M20. Using Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Providing weep holes in Brick masonry / Plain / Reinforced concrete abutment, wing wall / return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical specifications.

Supplying, Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications. Cement Concrete Blocks of size 0.3x0.3 x0.3 m cast in cement concrete of Grade M15

Supplying, Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification. Usingf 0.72 m³ of brick aggregates and 0.48 m³ of coarse sand (loose volume) per m³

Protection of embankment by closely driven 150 mm diameter eucalyptus Bullah each of 4500 mm total length, driven 2700 mm into the ground or bed of pond/ water body in standing water condition 3.50 m away from nearest edge of black top @350 mm center to center with 1800 mm exposed height of each bullah including fittings of three numbers 100 mm diameter half spited eucalyptus bullah Runner fitted & fixed two on top of each face of closed bullah walling and one on middle height of it, along full length of the wall including 100 mm diameter, 1350 mm long eucalyptus bullah Tie fitted @ 2000mm center to center with Tie-post anchoring by driving 100 mm diameter, 1350mm long eucalyptus bullah Tie-Post driven 1150 mm into ground on the road side @ 2000mm center to center , 2(Two) coat coal tarring on Eucalyptus bullah used and walling by earth filled gunny bag (@ 62 nos. bag per running meter length of protection line) by the side of the bullah walling after just after proper ‘benh-cutting’ of the existing embankment profile for proper placement of earth and to achieve finished earth filled slope as per directions including supplying eucalyptus bullah, coal-tar, nails, bolts, etc and labour charges for cutting, splitting bullah, coal tarring to each bullah driving charges for driving bullah into ground/ bed of pond in standing water condition, in between embankment and walling all complete in all respect as per drawing and direction of Engineer-in-Charge (Payment will be made on finished length of work in all respect complete as per specification & direction of Engineer –in-Charge as per approved methodology).

Supplying empty Cement bags in good condition. Filling empty Cement bags with dry earth stitching the bag (cost of thread included) and carrying and placing them in position and all incidental charges complete but excluding cost of sand and gunny bags.

PART-E: SURFACE DRAIN WORKS

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 for Rural Roads of MORD including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.

Fine Sand filling in foundation trenches and at the back of abutments, wing-walls etc. with good local sand free from earth in layers not exceeding 15 cm. including inundating each layer by profuse water and poking and ramming layer by layer complete including supply of sand. Quality of sand is to be approved by the Engineer-in-charge. The compaction factor for dry, clean sand may be taken as 0.835. (The payment is to be made on the basis of the finished compacted volume.)

Plain Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement complete as per drawing and technical specifications. PCC Grade M20. Using Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Plain / Reinforced Cement Concrete in Substructure with coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality, cement and water reducing admixtures, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete as per drawing and technical specification including the cost of necessary form work and staging complete as per drawing and technical specifications. RCC Grade M25 Height upto 5m Using Concrete Batching Plant (Minimum 15m3/hr.) with Automatic Control

Supplying, fitting and placing HYSD bar reinforcement in Sub-structure including initial straightening, straightening of coils bars, removal of loose rust (if any), cutting to requisite length bending, binding with annealed wire not less than 1 mm in size and conforming to IS 280 at every intersection hooked and bent to correct shape and placed on forms etc. including cost of black annealed wire and cost of loading, unloading, carriage of all steel materials complete as per drawing and technical specifications and direction of Engineer-in-charge. Tor Steel rods / HYSD bars / TMT (JSW JSPL / Shyam / SRMB//SSL/ BMASL / Electrosteel) (Fe 415 /Fe 500 /Fe 500D, conforms to IS: 1786 latest revision)

GST @ 18% on Item no 1 to 6

Labour Welfare Cess @ 1% on Item no 1 to 7