CWE/FZR-21/2023-24 Special repair to certain Md and OTM Accn Bldg No NP 09,NP 10,NP 11, DD 13,DD 14, P 11 and P 2A under GE (West) Ferozepur Cantt

Amount

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15 cm thickness below or above ground level complete all as specified & as directed by Engineer-in-Charge.

Material and labour PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in levelling course to receive floor finishes, filling of eaves gap, sides of interlocking tiles, filling of pressed steel chowkhats, etc complete all as specified & as directed by Engineer-in-Charge.

Material and labour Cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection, 75mm thick, surfaces finished even and smooth without using extra cement complete all as specified & as directed by Engineer-in-Charge.

Material and labour Cement concrete type B-1, 1:2:4 (20mm graded aggregate)using 40mm graded stone aggregate as in floor 40mm thick, surfaces finished even and smooth without using extra cement complete all as specified & as directed by Engineer-in-Charge.

Material and labour 25mm tick PCC(1:2:4)type B1 using 20 mm graded aggrigate as in floor finished even and rough to receive top layer complete all as specified & as directed by Engineer-in-Charge.

Material and labour for 38mm Glass dividing strips, 3 mm thick and inserted in position, conform to design complete all as specified & as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified & as directed by Engineer-in-Charge.

Material and labour Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour over a screed layer of 15 mm thick in CM 1:6 complete all as specified & as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18Sq m as in skerting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match and backing with 10 mm thick in CM 1:4 complete all as specified & as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.06 sq m but not exceeding 0.11Sq m in floors set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match the colour over a screed layer of 15 mm thick in CM 1:6 complete all as specified & as directed by Engineer-in-Charge.

Material and labour for 450X 350X 7mm thick glazed coloured (Digital colour) ceramic tiles on vertical surface of such as skirting, dados and risers to steps etc., including 10mm thick rendering in CM 1:4 on brick or concrete surface finished rough to received dado/ skirting, set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade with cement mortar bedding and removing off the premises complete all as specified & as directed by Engineer-in-Charge.

Material and labour for dark shade/ double charge/ ultracharge Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar(1:6) for laying floor finishes complete all as specified & as directed by Engineer-in-Charge.

Material and labour for dark shade/ double charge/ ultrachargeVitrified tile 10mm thick polished, area of tile n exc.0.36 sqm as in Skirting set and jointed in cement slurry over and including 10mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified & as directed by Engineer-in-Charge.

Material and labour for machine cut kota stone slab flooring 20-25 mm thick over 15 mm thick cement screed (1:6) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish complete all as specified & as directed by Engineer-in-Charge.

Material and labour for Kota stone slab 20-25 mm thick in skirting, etc over 15 mm thick cement screed (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish, complete all as specified & as directed by Engineer-in-Charge.

Material and labour for grinding and polishing on terrazzo topping treating the surface with beeswax polish complete all as specified & as directed by Engineer-in-Charge.

Taking down chowkhat with shutter exe 1.50 Sqm and n exe 4 Sqm( without taking off shutter) each complete all as specified & as directed by Engineer-in-Charge.

Taking down chowkat with shutter n.exe 1.50 sqm (without taking off shutters) each complete all as specified & as directed by Engineer-in-Charge. .

Taking down shutter n.exe 1 Sqm each of any description complete all as specified & as directed by Engineer-in-Charge.

Taking down shutter exe 1 Sqm but n exc 2 Sqm each of any description.

Supply and fixing Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified & as directed by Engineer-in-Charge.

Material and labour framed work such as grills etc with ends of bars shouldered and or riveted or forged into spike; framed guard bars and similar work conforming to Fe 410-0 0r Fe 310-0 complete all as specified & as directed by Engineer-in-Charge..

Supply and fixing Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010) complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified complete all as specified & as directed by Engineer-in-Charge..

All as per item no 26 above here-in-before but size 125x60mm with double rebate complete all as specified & as directed by Engineer-in-Charge..

Material and labour Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats,bed blocks, coping etc including necessary form work complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing factory made second class hard wood 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 35mm thick second class hard wood glazed and skelton shutters,open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat. complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified

Supply and fixing 20mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair 20mm clean sawn boarding with butt joints, chamfered one side fixed in repairs to replace and or decayed boarding to patches including cutting out old, piecing, heading joins etc in cupboard shelve complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide zink primer on steel surfaces complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of old wooden or wood based surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PTMT tower bolts, 200 mm long and fixed with steel screws complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PTMT handle 125mm long fixed with steel screws complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing powder coated anodised aluminium door window , ventilator etc fixed / sliding or pull and push type in shutter frames or shutters with two/three track sliding aluminium frame of Jindal /Hindalco (or) Equivalent make of approved size, including necessary joining cleats, glazing clips,powder coated aluminium snap beading, screws, roller including necessary anodised aluminium fittings like handles etc complete all as specified & as directed by Engineer-in-Charge.. Note: EPDM Rubber beading/gasket measured and paid seperatley.

Supply and fixing solar control film 25 micron reflective sticked to glass panes as per manufacturers instruction complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing EPDM Rubber beading around glass in aluminium windows /ventilator shutters complete all as specified & as directed by Engineer-in-Charge..

Supply and fixing 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified & as directed by Engineer-in-Charge.

Material and labour for 4mm thick aluminium panel 4 layer polimer resin coating of approved colour and shade fixed at aluminium door/ window complete all as specified & as directed by Engineer-in-Charge.

Dismantling of wall and ceiling boards (Fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover filletscomplete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair to Hollow PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain colour sheet inclusive of solvent cement and fixing on PVC frame as per specified in MES schedule part-I & II complete all as specified and directed by Engineer in Charge .

Supply and fixing in rep of Gypsum Board 6 to 7 mm thick in ceiling fixed with screw 60x60cm placed in ceiling (Angle 25mm X 25mm , Main tee 38mmX23mm ,Sub tee 23mmX23mm) incl aluminium anodised/powder coated snap grid frame 605X605 mm for false ceiling incl hanging arrangement complete all as specified & as directed by Engineer-in-Charge. Note:-The hanging stay wire shall not be less than 4.00mm thick all are included in the above mentioned item only.

Supply and fixing 200mm long aluminium, anodised barrel tower bolts of extruded section,complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 150mm Extruded aluminium alloy handle complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Aluminium alloy, anodised, sliding door bolt 300mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 30mm continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each pane complete with oil putty complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair to 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm incl. incl hacking out old broken glass and putty/beading complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staple etc complete all as specified..

Supply and fixing in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing granite( of any type) stone slab of 20mm thick laid over 15mm thick cement screed bed in CM1:6 machine cut,size and jointed over grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs brass chromium plated bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs brass chromium plated long body bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressurecomplete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs chromium plated cast copper alloy 1-way angle cock with flange suitable for 15mm bore pipe, complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing wall mixer with 'L' bend (Provision for OH shower) 15mm for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs CP brass shower rose 150mm size shower with 300mm arm suitable for 15mm bore pipe complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Cabinet Mirror (400mm x 500mm) complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing CP soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified and as directed by Engr -in- charge

Supply and fixing in repair PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair Vitreous china white squatting pan orrissa pattern of size 630mm x 450 mm with integral foot rests including necessary cement concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair, complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repairs, Vitreous china wash hand basin, white flat back size 550x400mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PVC waste pipe of standard pattern, not less than 75cm long , 32/40mm dia for steel sink waste coupling or urinal of suitable size complete all as specified & as directed by Engineer-in-Charge..

Supply and fixing galvanised steel tubing, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 15 mm dia including taking up or down old steel tubing complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing galvanised steel tubing, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 20 mm dia including taking up or down old steel tubing complete all as specified & as directed by Engineer-in-Charge.

Dismantling brick work built in cement mortar of any specification and in any position complete all as specified & as directed by Engineer-in-Charge.

Material and labour Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified & as directed by Engineer-in-Charge.

All as per item above but using old bricks retrieved from item no 78 demolition including cleaning and removal of mortar from old bricks complete all as specified & as directed by Engineer-in-Charge.

Material and labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as specified & as directed by Engineer-in-Charge.

Demolition of reinforced cement roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified & as directed by Engineer-in-Charge

Material and labour for RCC 1:1½ :3 (20mm graded aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span and similar work complete all as specified & as directed by Engineer-in-Charge.

Use and waste of formwork to sides and soffits of floor or roof beams, beam similar work to rough finish surface of concrete flat complete all as specified & as directed by Engineer-in-Charge..

Supply and fixing Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & as directed by Engineer-in-Charge.

Material and labour TMT mild steel bars 5 to 10mm dia,as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips

Taking down cement plaster any description on brick or stone walls, /RCC walls surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified & as directed by Engineer-in-Charge.

Material and labour 10 mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth with out using extra cement complete all as specified & as directed by Engineer-in-Charge.

Material and labour Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or conrete surfaces, surfaces finished even and fair complete all as specified & as directed by Engineer-in-Charge.

Material and labour for internal rendering 12mm thick on any faces of brickwork or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified & as directed by Engineer-in-Charge.

Material and labour Rendering 5mm thick in cement mortar (1:3) on in ceiling, soffits of chajja or similar location any face of brick walls or conrete surfaces, surfaces finished even and smooth without using extra cement,etccomplete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over a coat of primer and applying a coat of 1mm thick wall care putty complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified & as directed by Engineer-in-Charge.

Material and labour Preparation of new plastered surfaces and applying three coats white washing on ceiling surfaces complete all as specified & as directed by Engineer-in-Charge.

Material and labour for white washing one coats on ceiling incl preparation of old plastered surfaces.complete all as specified & as directed by Engineer-in-Charge.

Material and labour for complete removal of old existing treatment on walls, cornices etc by brooming down or steel wire brushing scrapping down smoke soot moulds, moss and efflorescence salt and trading oil decorated surface of walls and applying a coat of wall care putty of approved make as on wall surface and two coats of oil based distemper (white or tinted) complete all as specified & as directed by Engineer-in-Charge.

Material and labour for complete removal of old existing surface and applying two coats cement based paint over one coat of alkali resistant priming paint complete all as specified & as directed by Engineer-in-Charge.

Surface excavation nexc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified & as directed by Engineer-in-Charge.

Material and labour Cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in subbase of interlocking 100mm thick, complete all as specified complete all as specified & as directed by Engineer-in-Charge.

Material and labour for precast machine pressed cement concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade, glossy type with grey cement and pigment laid dry over a layer of 25 mm thick sand cushioning complete all as specified & as directed by Engineer-in-Charge.

Material and labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified & as directed by Engineer-in-Charge.

Material and labour PCC 1:2:4 type B-1 using 20m graded stone aggregates as in kerbs, rounded or chamfered on edges complete all as specified & as directed by Engineer-in-Charge.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified & as directed by Engineer-in-Charge.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified & as directed by Engineer-in-Charge.

Material and labour 10 mm thick screed bed or bedding layer of mortar in CM (1:4) with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane. Note: WPC shall be measured and paid separately complete all as specified & as directed by Engineer-in-Charge.

Supply only water proofing compound.

Material and labour for applying a layer of blown grade of industrial bitumen 85/25 @ 1.20 Kilogram per square metre including preparation of roof surfaces complete all as specified & as directed by Engineer-in-Charge.

Material and labour For APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) Laid on primed surface by forced application including bitumen primer ccomplete all as specified & as directed by Engineer-in-Charge.

Material and labour for 80mm thick average consolidated thickness mud phuska on flat roof ncluding 25mm thick mud plaster complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 40 mm thick brick tiles laid on mud mortar and joints grouted flus in cement mortar(1:3) mixed with 5% of crude oil by wt of cement on mud phuska complete all as specified & as directed by Engineer-in-Charge.

All as item No 110 here in before but except tiles complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410 -W (Gde- E- 250) quality- A complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified & as directed by Engineer-in-Charge.

Material and labour for raking out joints / pointing incl Flush pointing in CM (1:3) to brick work or brick tiles, laid flat, in floors, surface channels, roofs, etc in cement mortar complete all as specified & as directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work window, door of any description not otherwise provided for complete all as specified & as directed by Engineer-in-Charge.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in sectioncomplete all as specified & as directed by Engineer-in-Charge.

Supply and fixing for rolled sections Fe 410 -W (Gde- E- 250) quality- as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 1.00 mm thick stainless steel plate rack of size 750x600x250 mm complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified & as directed by Engineer-in-Charge.

Demolition of cement concrete in sunken portion any description and in any position not otherwise specifically provided complete all as specified & as directed by Engineer-in-Charge.

Material and labour 15mm thick CM(1:3) with WPC on walls as well as on sunken floor portion finished even and smooth using extra cement. Note:- WPC shall be measured and paid separately.

Material and labour PCC (1:5:10) type E-2 (using 40 mm graded aggrigate ) as in filling under sunken portion

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Supply and fixing 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 75mm dia PVC (SWR) bends any radius complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 110 mm dia PVC (SWR) bends any radius complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 75 mm dia PVC (SWR) bends any radius with access door complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 110 mm dia PVC (SWR) bends any radius with access door complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 75 mm dia PVC (SWR) vent cowl complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing 110 mm dia PVC (SWR) vent cowl complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) multi floor trap with grating including jointing with solvent cement 75 mm dia outlet complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing ball valves of 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair ball valves of 20 mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed 20 mm dia complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed 15 mm dia complete all as specified & as directed by Engineer-in-Charge.

Material and labour for white color rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I capacity of the tank 500 ltrs including GI tank nipple of size 20/15 mm dia including dismantling of old water tank ccomplete all as specified & as directed by Engineer-in-Charge.

Material and labour for disconnecting existing 500 ltr capacity tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position incl nesesary fittings complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing mild steel curtain rod powder coated with fixing side brackets, end cup, rings @10 Nos per running metre and fixed with PVC rawl plugs & steel screws complete all as specified & as directed by Engineer-in-Charge..

Removing excavated soil material to a distance n exc 50 m and deposited where directed at a level n exc 1.5 m above the starting point complete all as specified & as directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for cesspit, manhole etc,and getting out in soft/loose soil even in foul position complete all as specified & as directed by Engineer-in-Charge.

Demolition and breaking up of existing drain pipe (SGSW/PVC/RCC etc) set in cement mortar of internal dia of pipe 150 mm complete all as specified & as directed by Engineer-in-Charge.

Returning, filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified & as directed by Engineer-in-Charge.

Material and labour for 150 mm bore PVC (SWR) pipe laid in trenches and jointed with cement mortar complete all as specified & as directed by Engineer-in-Charge.

Material and labour PCC 1:3:6 type C2 (using 40 mm graded aggregate) as in concrete bed to 150 mm bore drain pipe incl packing under hunching against the sides of pipes after pipe laid and tested complete all as specified & as directed by Engineer-in-Charge.

Material and labour for RCC 1:2:4, type B1 (using 20mm graded aggregate) Precast cement concrete as in cover slab for man hole and similar article with plain face. Set in cement mortar 1:4 complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing deformed or twisted TMT bar 8 mm dia cut to length, bent to shape required, incl cranking bending and binding with MS wire (annealed) not less than 0.9mm or securing with clips complete all as specified & as directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out Material and labour existing benching for and forming branch channel (1/2 round or 3/4 section) for 150 mm dia pipe in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified & as directed by Engineer-in-Charge.

Material and labour for brick work with subclass 'B' bricks straight or curved on plan exe 6mm mean radius built in cm 1:4 complete all as specified & as directed by Engineer-in-Charge.

Material and labour for rendering 12 mm thick on wall in cement mortar 1:3 on fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement complete all as specified & as directed by Engineer-in-Charge.

Material and labour for rendering 12 mm thick on wall in cement mortar 1:4 on fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement complete all as specified & as directed by Engineer-in-Charge.

Taking down carefully copper /aluminium point wiring (light, fan, socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified & as directed by Engineer-in-Charge.

M &L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified & as directed by Engineer-in-Charge for One light/fan/Bell Point controlled by one single pole one way switch.

ditto all as per item No 154 above but one socket outlet on the same board controlled by one single pole one way switch complete all as specified & as directed by Engineer-in-Charge

ditto all as per item No 154 above but one 5 amps socket outlet independent controlled by one single pole 5 Amp switch complete all as specified & as directed by Engineer-in-Charge

ditto all as per item No 154 above but One light point controlled by two way switches, with cables 1.5 sq.mm size complete all as specified & as directed by Engineer-in-Charge

All as per Item No 154 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked complete all as specified & as directed by Engineer-in-Charge.

Supply & Fixing Switch piano, flush type single pole, 2 way 6 Amp complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing Socket outlet 2 in one, 5/6 Amps flush type ISI marked complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing bell push flush type 5 Amps duly ISI marked complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing bell ding dong type AC 230 Volt single pole.

Supply & Fixing ceiling rose, PVC/Polycarbonate,isolated three terminals complete all as specified & as directed by Engineer-in-Charge.

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulb complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing bell ding dong type AC 230 Volt single pole complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulb complete all as specified & as directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified & as directed by Engineer-in-Charge

Supply and fixing in repair stepped type electronic fan regulater flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified & as directed by Engineer-in-Charge

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louverscomplete all as specified & as directed by Engineer-in-Charge

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified & as directed by Engineer-in-Charge

Supply and fixing LED tube light fitting 1 X 20 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified & as directed by Engineer-in-Charge

Supply & Fix in repair LED tube light fitting 9 watts batten type fixed on wall/ ceiling etc. including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified & as directed by Engineer-in-Charge

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with highefficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified & as directed by Engineer-in-Charge

Supply and fixing LED street/security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified & as directed by Engineer-in-Charge

Sheet Metal Enclosures with Socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amp complete complete all as specified & as directed by Engineer-in-Charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified & as directed by Engineer-in-Charge.

Supply & Fixing MCCB 100 Amps, 415 volts, 16 KA, 4 Pole ccomplete all as specified & as directed by Engineer-in-Charge

Supply & Fixing MCB, Single pole 240 V, 6 - 32 Amps 10 KA 'B' Series complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing in repair MCB single pole (SP) 240 volts, 40 Amps, 10 KA 'B' Series complete all as specified & as directed by Engineer-in-Charge

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series complete all as specified & as directed by Engineer-in-Charge.

Material and labour for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run) complete all as specified & as directed by Engineer-in-Charge

All as per item No 186 but 4 Sqmm Sub main wiring

Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50 sqmm 3.5 core complete all as specified & as directed by Engineer-in-Charge

Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm 4 core complete all as specified & as directed by Engineer-in-Charge

Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm 4 core complete all as specified & as directed by Engineer-in-Charge

Material and labour for sand cushioning with a layer of fine sand 8 cm thick begore laying of cable and 5 cm thick after laying of cable in trenches complete all as specified and as directed by Engineer-in-Charge. Notes : (i) Excavation and earth work to be measured and paid separately). (ii) Thickness of 18 cms after punning shall be considered for payment.

Material and labour for Bricks (Size 23x11.5x7.5 cm) common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry width wise acrose the line of cable in trenches for protection of UG cable complete all as specified & as directed by Engineer-in-Charge

Material and labour for Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required complete all as specified & as directed by Engineer-in-Charge

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm complete all as specified & as directed by Engineer-in-Charge and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Dee Kay EnterPrises

HARBHAJAN SINGH KHARBANDA

M/s Surjit Singh and bros