Providing Street Light from Maharana Pratap Chowk to Ram Garh Bye Pass Road at Kalayat in District Kaithal.

Amount

23.5 Coppper Wiring in existing PVC / MS Conduit Pipe Surface / Recessed

23.5.6 Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated copper conductor cable 1100 volts grade in existing MS / PVC conduit etc. as required

23.5.6.1 1 Run of Size 1.50 Sqmm (1/1.40 mm)

23.22 MCCB, Distribution Boards, MCB's, RCCB's, Change Over etc.

23.22.1 Supply and erection of moulded case circuit breakers single pole / 4 pole on existing wall /pedestal/Panel including bonding to earth and making necessary connections required to complete the job in all respect upto the entire satisfation of the Engineer-in-Charge of the work.

23.22.1.3 Triple Pole MCCB 16 Amp. to 100 Amp., 25 Ka

23.22.4 Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge of the work

23.22.4.5 TPN DB Horizontal Type Double Door 4 Way (8 Incoming and 3 Phase * 4 Outgoing)

23.22.5 Supply and erection of miniature circuit breaker 240/415 V in the existing distribution board including making necessary connections.

23.22.5.1 6 Amp. to 32 Amp. Single Pole

23.27 Supply and Erection of Godrej Almirah type M.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. Sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars. The top covering should have downward overhang of 75 mm on all sides of pedestal, having two sets of water proof ventilation holes of suitable size on the sides, at top and bottom, each set containing four Nos. holes to discharge the heat produced by the current. The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof. The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block, projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:-

23.27.2 M.S. Pedestal of size 750 mm wide, 900 mm high, 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 1050 mm x 600 mm x 250 mm below ground level .

24.1 Earthing and Lightening Arrestor

24.1.1 Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. (but without charcoal or coke and salt) as required.

24.1.2 Extra for using salt and charcoal / coke for pipe earth electrode as required.

24.1.11 Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required.

24.4.8 Supply and erection of Hot Dip Galvanized octagonal pole of 3 mm thickness with base plate including cost of nut and bolts, earthing studs integral cable termination arrangement 5 mm thick bakelite base plate on suitable welded MS/GI bracket 32 amp 4 way connector 2 nos. 10 Amp SP MCB, end cover and all accessories as supplied by the manufacturer including providing RCC foundation of M25 grade (1 Cement: 1 Stone Aggregate: 2 Coarse sand) i/c exacavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respect and nas per direction of Engineer-in-Charge. Make: GE/PHILIPS/VIPIN ST/ SKIPPER

24.4.8.5 7 metre long pole with top dia 75 mm and bottom dia 150 mm with base plate os size 300 x 300 x 20 mm.

24.5.2 S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2, laid 0.75 metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.

24.5.2.3 DWC /HDPE pipe 63/50 mm outer dia / inner dia.

24.4.15 B. S. E. N. 10025 High Masts

24.4.15.3 Supply, Installation, Testing and Commissioning of 20 Mtr. Long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in 2 (Two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 Nos. luminaire loading fully motorized (Power Tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 Nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto the entire satisfaction of Engineer-in-Charge. Thickness of Top and Bottom Section = 3 mm & 4 mm (Minimum) Top Dia = 150 mm and Bottom Dia = 460 mm Thickness of Galvanization - Top = 65 Micron (Minimum) and Bottom = 85 Micron (Minimum)

24.9 RCC Foundation for High Mast Octagonal Poles

Providing RCC Foundation of M 25 Grade (1 Cement: 1 Stone: 2 Coarse Sand) i/c excavation, steel reinforcement (Fe 500) @ 75 Kg/Cum of concrete contents, concrete cover 50 mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for high mast octagonal poles of various heights as per following specifications complete in all respect and as per directions of Enigineer - in - Charge

24.9.3 20 M high Mast Pole

M.R. items

N.S - 1 Supply & Erection of Single Arm Bracket made of 40mm dia G l pipe B class lSl 1.25mtr. Long with coller pipe (Gl) 75mm dia 60 cm Long top covered with ornamental cap duly welded painted 2 coats of aluminum paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.

N.S - 2 Supply and Erection of LED Street Light Lumanaries of Havells make Endura PLEARL NEOSL 60W LED or its equivalent model and specifications of Wipro/Phillips/Crompton/SURYA make with die cast housing, toughened glass IP66 with all accessories as supplied by the manufacturer with all labour and material required to complete the job in all respect upto the Entire Satisfaction of the Engineer-in-Charge of the work.

N.S - 3 Supply & Erection of 65 Amp. 3 Phase automatic / digital time switch of Indo Asian make HSN code 8537 along with contactor of required capacity of Indo Asian make movement controlled by preciosity quartz oscillation operation on main supply of continue to run on built in rechargeable nickle cadium call for 150 hours in the event of power failure including cost of all petty items complete in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

N.S - 4 Supply & erection of outdoor duly factory manufactured feeder panel to operate S/L system made out of C.R.C.A. sheet 2 mm thick of App. Size (1100 L x 1400 H x 300 D) mm with hot type canopy ventilation slots (box type) angle iron / channel iron frame of 40 mm x 40 mm x 6 mm on both sides. The panel should have double door godrej Almirah type weather proof with locking arrangement. The panel as such be made in two compartments one for space of energy meter with glass & solid wire mesh and sealing arrangements. The second compartment to accommodate the complete control system. Both the compartment is to accommodate system of set of timer, Copper Bus bar of size 400 mm x 20 mm x 3 mm duly tinned & insulated. The panel duly painted in powder coated gray shade. The main pannel door fixed with rubber gasket of superior quality to make it water proof. The panel should be fixed on 1:2:4 C.C. Block size 1300 mm x 500 mm x 250 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster having a C.C. base of size 1500 mm x 750 mm x 250 mm below ground level.

N.S - 5 Supply and erection of 40 Amp. 3 Phase AC Energy Meter in built C. T. 40/5 ( Approved by H.V.P.N on existing pole with clamps of required size including making necessary connections with petty material required to Complete the Job in all respect up to entire satisfaction of Engineer -in-Charge of the work.

N.S - 6 Supply and Erection of LED flood light Luminaire 250W of Makes: Havells make JETAVALOUR FL 240 W LED 757 MODWBLTG or its equivalent model of Philips /Wipro /Crompton/Bajaj/Surya with lense with high power LED flood light in aluminium PDC housing, toughened glass cover with IP 66 protection and accessories required to complete the job in all respect including erection an making connection with other petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

N.S - 7 Supply & Erection of Underground cable loose in existing pipe or trenches complete in all respect up to the entire satisfaction of Engineer-in-Charge of the work.

i) 16 Sqmm. 4 Core cable (Armoured)

ii) 25 Sqmm. 4 Core cable (Armoured)

M/S PANJETA ELECTRICALS