Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.5 CrAccepted-Finance PLAT NO 943 54TH STREET T V S COLONY ANNANAGAR WEST EXTENSION CHENNAI PIN 600 101 | CHENNAI | CHENNAI | TAMIL NADU | 600101 | ₹1.5 Cr | L1 | Accepted-Finance L1 |
| 2 | L2₹1.6 Cr+₹4.4 L (2.87%)Rejected-Finance | ₹1.6 Cr+₹4.4 L (2.87%) | L2 | Rejected-Finance L2 |
| Sl No | Description | Qty | Unit | Eco Protection Engineers Pvt Ltd L1 | Global Tech Services L2 |
|---|---|---|---|---|---|
| 1.00 | Monthly O&M charges for Water Supply and Distribution System | 12 | Months | 7,37,000 ₹1,04,35,920 Lowest | 7,55,500 ₹1,06,97,880 |
| 2.00 | Monthly Sample test of drinking water for following parameters. Color, odour, Turbidity (NTU), pH value, Total Hardness as CaCO3, Calcium as Ca, Magnesium as Mg, Chloride as Cl, Total Dissolved Solids, Sulphate as SO4, Nitrate as NO3, Fluoride as F, Iron as Fe, Chromium as Cr 6+, Zinc as Zn, Copper as Cu, Manganese as Mn, Aluminium as Al, Boron as B, Total Alkalinity as CaCO3, Total Coliform MPN/100 ml, E Coli MPN/100 ml. From NABL accredited Lab-MR | 144 | No | 2,950 ₹5,01,264 | 2,800 ₹4,75,776 Lowest |
| 3.00 | Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m | 100 | Cum | 950 ₹1,12,100 Lowest | 1,050 ₹1,23,900 |
| 4.00 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | 200 | Cum | 275 ₹64,900 | 240 ₹56,640 Lowest |
| 5.00 | Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils Depth upto 3 m | 100 | Cum | 350 ₹41,300 Lowest | 560 ₹66,080 |
| 6.00 | Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m. With Dewatering | 100 | Cum | 1,150 ₹1,35,700 | 1,050 ₹1,23,900 Lowest |
| 7.00 | Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils Depth upto 3 m . With Dewatering | 100 | Cum | 450 ₹53,100 Lowest | 560 ₹66,080 |
| 8.00 | Demolishing cement concrete manually/ by mechanical means including disposal of material to the appropriate disposal area as per direction of Engineer-in-charge. | 5 | Cum | 1,550 ₹9,145 Lowest | 1,550 ₹9,145 Lowest |
| 9.00 | Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates | 10 | Cum | 7,900 ₹93,220 | 7,550 ₹89,090 Lowest |
| 10.00 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90L/10 m² over an under coat of primer applied @ 0.80 L/10 m² of approved brand and manufacture including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. | 25 | Sq.M | 210 ₹6,195 Lowest | 250 ₹7,375 |
Tender Value
₹1.4 Cr
EMD Value
₹2.1 L
Closing Date
6 Aug 2025, 3:30 pmClosed
Registrar
IISc, Bangalore
Annual Operation and Maintenance of Water Supply and distribution system 2025- 2026 at IISc Bangalore
2025_IISC_869417_1
IISc/Tender-AMC-1/2025-26
Open Tender
Civil Works
Works
365 days
IISc, Bangalore
As Per Tender Documents
2 documents required · 2 mandatory
₹0
₹2.1 L
MS Teams Online
19 Jan 2026
17 Jul 2025
7 Aug 2025
18 Jul 2025
6 Aug 2025
31 Jul 2025
28 Jul 2025
Amount
Monthly O&M charges for Water Supply and Distribution System
Monthly Sample test of drinking water for following parameters. Color, odour, Turbidity (NTU), pH value, Total Hardness as CaCO3, Calcium as Ca, Magnesium as Mg, Chloride as Cl, Total Dissolved Solids, Sulphate as SO4, Nitrate as NO3, Fluoride as F, Iron as Fe, Chromium as Cr 6+, Zinc as Zn, Copper as Cu, Manganese as Mn, Aluminium as Al, Boron as B, Total Alkalinity as CaCO3, Total Coliform MPN/100 ml, E Coli MPN/100 ml. From NABL accredited Lab-MR
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
Demolishing cement concrete manually/ by mechanical means including disposal of material to the appropriate disposal area as per direction of Engineer-in-charge.
Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates
Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90L/10 m² over an under coat of primer applied @ 0.80 L/10 m² of approved brand and manufacture including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.
Providing Brick work with Non Modular fly ash bricks conforming to IS:12894, class designation 5.0 average compressive strength in super structure above plinth level up to floor I level in Cement mortar 1:4 (1 cement : 4 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work.
Half brick masonry with Non Modular fly ash bricks of class designation 5.0, conforming to IS :12894, in super structure above plinth and upto floor I level cement mortar 1 : 3 (1 cement : 3 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work.
Cement (OPC/PPC/PSC)
Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material to the appropriate disposal area as per direction of Engineer-in-charge Bituminous road
Supplying, Placing & Compacting Ready Made Plant mixed Cold Bituminous Pothole patching mix in accordance with IRC 116-2014 in 50kgs plastic sturdy bags. The mix shall contain at least 5.6% MC 800 Cutback Bitumen conforming to IS 217 Specification and suitable anti-stripping agent @ 0.3% by weight. The mix shall be workable for at least 6 months. The material shall be intended for patching potholes up to 40mm thick layers and for deeper potholes, the mix shall be placed and compacted in 40mm thick layers complete as per technical specifications. Cold Bituminous Pothole Patching Mix
Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge
Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. heavy duty cobble stones 60mm thick interlock pavers
Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge with available Stone
Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand)
Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste including cost of all materials, labour, scaffolding and usage charges of machineries & other incidental charges complete as per the direction of engineer incharge of work.
Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing pipe and repairing the hole after insertion of pipe. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.
CPVC Pipe Standard Dimension Ratio-SDR 11 Elbow 50mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Elbow 40mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Elbow 32 mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Elbow 25 mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Elbow 20mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Bend 25mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Bend 20mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Bend , 32mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 -Bend , 40mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Bend , 50mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Nipple 50mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Nipple 40mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Nipple 32mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Nipple 25mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Nipple 20mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Tee 50mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Tee 40mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Tee 32mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Tee 25mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Tee 20mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Coupling 50mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Coupling 40mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Coupling 32mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Coupling 25mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Coupling 20mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Union 50mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Union 40mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Union 32mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Union 25mm dia
CPVC Pipe Standard Dimension Ratio-SDR 11 Union 20mm dia
Supply and delivery at site GM (copper alloy) gate valves confirming to Class-I as per IS 778 with latest amendments, 1 No. screwed in bonnet inside screw, rising spring spindle integral seat screwed females ends confirming to IS 554/ 1990 body hydraulically tested 1.5HP seat standard tested 1 HP with IS mark. 20 mm Dia
Supply and delivery at site GM (copper alloy) gate valves confirming to Class-I as per IS 778 with latest amendments, 1 No. screwed in bonnet inside screw, rising spring spindle integral seat screwed females ends confirming to IS 554/ 1990 body hydraulically tested 1.5HP seat standard tested 1 HP with IS mark. 25 mm dia
Supply and delivery at site GM (copper alloy) gate valves confirming to Class-I as per IS 778 with latest amendments, 1 No. screwed in bonnet inside screw, rising spring spindle integral seat screwed females ends confirming to IS 554/ 1990 body hydraulically tested 1.5HP seat standard tested 1 HP with IS mark. 50 mm dia
Gunmetal non-return valve-horizontal (screwed end) 25 mm dia
Gunmetal non-return valve-horizontal (screwed end) 32mm dia
Gunmetal non-return valve-horizontal (screwed end) 40 mm dia
Gunmetal non-return valve-horizontal (screwed end) 50 mm dia
Gunmetal non-return valve-horizontal (screwed end) 65 mm dia
Gunmetal non-return valve-horizontal (screwed end) 80 mm dia
Gunmetal non-return valve-vertical (screwed end) 25 mm dia
Gunmetal non-return valve-vertical (screwed end) 32 mm dia
Gunmetal non-return valve-vertical (screwed end) 40 mm dia
Gunmetal non-return valve-vertical (screwed end) 50 mm dia
Gunmetal non-return valve-vertical (screwed end) 65 mm dia
Gunmetal non-return valve-vertical (screwed end) 80 mm dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work SDR -11 20 mm Dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work SDR -11 25 mm Dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work SDR -11 32 mm Dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work SDR -11 40 mm Dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work SDR -11 50 mm Dia ,
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work SDR -11 65 mm Dia ,
Supply and delivery at site wrought middle steel (galvanized) GI plugs confirming to IS 1239-II, 1991 with latest amendments Plugs For 25 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI plugs confirming to IS 1239-II, 1991 with latest amendments Plugs For 32 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI plugs confirming to IS 1239-II, 1991 with latest amendments Plugs For 40 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI plugs confirming to IS 1239-II, 1991 with latest amendments Plugs For 50 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI plugs confirming to IS 1239-II, 1991 with latest amendments Plugs For 65 mm dia
Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 25 mm dia
Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 32 mm dia
Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 40 mm dia
Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 50 mm dia ,
Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 65 mm dia
Providing wrought mild steel (galvanized) GI collar confirming to IS 1239-II, 1991 with latest amendments if any. For 80 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for: For 25 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for: 32 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for: 40 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for:50 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for: 65 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI elbow confirming to IS 1239-II, 1991 with latest amendments if any for: 80 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI hexagonal nipple confirming to IS 1239-II, 1991 with latest amendments if any.25 mm dia ,
Supply and delivery at site wrought middle steel (galvanized) GI hexagonal nipple confirming to IS 1239-II, 1991 with latest amendments if any.32 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI hexagonal nipple confirming to IS 1239-II, 1991 with latest amendments if any.40 mm dia ,
Supply and delivery at site wrought middle steel (galvanized) GI hexagonal nipple confirming to IS 1239-II, 1991 with latest amendments if any.For 50 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI hexagonal nipple confirming to IS 1239-II, 1991 with latest amendments if any.For 65 mm dia
Supply and delivery at site wrought middle steel (galvanized) GI hexagonal nipple confirming to IS 1239-II, 1991 with latest amendments if any.For 80 mm dia
3 “M.S. FLANGE
Supplying of special moulded variety PVC couplers as per IS 7834/ 1987 and fabricated as per IG124/ 1984 with ISI mark and with its latest amendments to work site etc. complete 32mm dia
Supplying of special moulded variety PVC couplers as per IS 7834/ 1987 and fabricated as per IG124/ 1984 with ISI mark and with its latest amendments to work site etc. complete 40mm dia ,
Supplying of special moulded variety PVC couplers as per IS 7834/ 1987 and fabricated as per IG124/ 1984 with ISI mark and with its latest amendments to work site etc. complete 50mm dia ,
Supplying of special moulded variety PVC couplers as per IS 7834/ 1987 and fabricated as per IG124/ 1984 with ISI mark and with its latest amendments to work site etc. complete 63mm dia ,
Welding Rod Rate
Insulation Tape
Cutting Wheel 4" dia
Araldite 100GMS
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Female Threaded Adapter , 20mm dia
CPVC Specials SDR -11, Female Threaded Adapter , 25mm dia
CPVC Standard Dimension Ratio-11 CPVC Specials, Female Threaded Adapter , 32mm dia
CPVC Standard Dimension Ratio-11 CPVC Specials Female Threaded Adapter , 40mm dia
CPVC Pipe Standard Dimension Ratio-11 Specials 50mm dia Female Threaded Adapter ,
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Threaded Adapter , 20mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Threaded Adapter , 25mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Threaded Adapter , 32mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Threaded Adapter , 40mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Threaded Adapter , 50mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Female Brass Threaded Adapter 20mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Female Brass Threaded Adapter 25mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Female Brass Threaded Adapter 32mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Female Brass Threaded Adapter 40mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Brass Threaded Adapter 20mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Brass Threaded Adapter 25mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Brass Threaded Adapter 32mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Male Brass Threaded Adapter 40mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials End Cap , 20mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials End Cap , 25mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials End Cap , 32mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials End Cap , 40mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials End Cap , 50mm dia
CPVC Pipe Standard Dimension Ratio- 11 PVC Specials Gate Valve , 20mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Gate Valve , 25 mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Gate Valve , 32 mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Gate Valve , 40 mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Gate Valve , 50 mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,20x15mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,25x20mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,25x15mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,32x25mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,40x25mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,40x32mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,50x32mm dia
CPVC Pipe Standard Dimension Ratio-11 CPVC Specials Reducer ,50x40mm dia
CPVC Solvent 237ml
Rewinding of submersible pumpset with copper winding wires of appropriate guage, as per specifications and / or directions of the departmental officials, including all materials, labour, equipment and testing. for all types of submersible pumpsets etc.(with guarantee period not less than 6 months) For all types of submersible pumpsets upto 3.0 H.P.
For all types of submersible pumpsets above 3 HP and upto 5.0 H.P
For all types of submersible pumpsets above 6.5 HP and upto 7.0H.P.
For all types of submersible pumpsets above 10 HP and upto 11 H.P.
For all types of submersible pumpsets above 14 HP and upto 15 H.P.
For all types of submersible pumpsets above 15HP and upto 20 HP
MP Grease
c. LABOUR: (Welder)
20mm Brass Float Valve
25mm Brass Float Valve
32mm Brass Float Valve
40mm Brass Float Valve
50mm Brass Float Valve
32mm PVC FTA
40mm PVC FTA
50mm PVC FTA
63mm PVC FTA
32mm PVC MTA
40mm PVC MTA
50mm PVC MTA
63mm PVC MTA
Tefflon Tape
Hexa Blade
Thread Ball
Shellac
M.seal 100 Gms
Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest mendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete 100mm Dia
Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest amendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete 150mm Dia
Providing and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of Ductile Iron (DI) conforming ti IS-1865 with the latest amendments and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 with the latest amendments only. The stem sealing should be with toroidal sealing rings (minimum 2 " O " rings). Body and bonnet should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. For PN-10: (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) etc. complete 200mm Dia
Spares Supply and Installationof KSB Make Vertical Inline Pump - Model: Movitec VCF 60B%- B/30Kw Stage Casing with Bearing 40HP
Spares Supply and Installationof KSB Make Vertical Inline Pump - Model: Movitec VCF 60B%- B/30Kw Bearing Sleeve 40HP
Spares Supply and Installationof KSB Make Vertical Inline Pump - Model: Movitec VCF 60B%- B/30Kw Impeller reducer Head 40HP
Spares Supply and Installationof KSB Make Vertical Inline Pump - Model: Movitec VCF 60B%- B/30Kw Pump Shaft 40HP
Spares Supply and Installationof KSB Make Vertical Inline Pump - Model: Movitec VCF 60B%- B/30Kw Shroud O ring Kit 40HP
Spares Supply and Installationof KSB Make Vertical Inline Pump - Model: Movitec VCF 60B%- B/30Kw Service charges for pump Dismantling, checking, replacement of spares , assembling and realignent 40HP
Fishing out power pump from the borewell including the cost of labour, materials, with all lead and lifts etc. complete
Lifting of struck up submersible pump set. Upto 300 ft
Rewinding of monoblock motor with copper insulaton wire suitable gauge as per ISI specification with all necessary materials and labour,tools and equipments with guarantee period of not less than 12 months upto 7.5 HP monobloc motor rewinding
Rewinding of monoblock motor with copper insulaton wire suitable gauge as per ISI specification with all necessary materials and labour,tools and equipments with guarantee period of not less than 12 months 10 HP monobloc motor rewinding
Rewinding of monoblock motor with copper insulaton wire suitable gauge as per ISI specification with all necessary materials and labour,tools and equipments with guarantee period of not less than 12 months 15 HP monobloc motor rewinding
Rewinding of monoblock motor with copper insulaton wire suitable gauge as per ISI specification with all necessary materials and labour,tools and equipments with guarantee period of not less than 12 months 20 HP monobloc motor rewinding
Supplying and fixing of DI Saddle Clamp (Screwed Type ) SIze 100mmx50mm
Supplying and fixing of DI Saddle Clamp (Screwed Type ) SIze 100mmx40mm
Supplying and fixing of DI Saddle Clamp (Screwed Type ) SIze 100mmx25mm
Installation of Product pipe by Guided Auger Boring Method including making entry and exit pits, including all related civil works like excavation, shoring / strutting, de-watering, shielded excavation through Auger Boring Process, lowering of pipe segments in the jacking pit, laying and jointing of Product pipeline through jacking process from Jacking pit including the cost of RCC NP3 S&S or as required pipes including dewatering and other works required for commissioning of the works in all types of soil including Rock complete with all lead and lift as per specifications and as directed complete for the following diameter of pipes. upto 300mm
Providing Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000;3Phase, SS Bowl & Impeller with Low volt Motor as per specifications, to work site as per necessary ammendments and instructions of engineer incharge of work. 3.00 HP - 90 LPM @ 66 m = 10 STG Outlet dia 2"
Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-inCharge.
Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For: Heavy Duty GI pipe of 20mm dia
Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For: Heavy Duty GI pipe of 25mm dia
Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI pipe of 32mm dia
Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI pipe of 40mm dia
Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI pipe of 50mm dia
Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI pipe of 80mm dia
Providing, Laying and Fixing of GI pipes conforming to IS 1239:1990 with latest amendments complete with GI fittings (excluding the cost of fittings) with cuts and threads wherever necessary, including testing for water tightness, with all lead and commissioning. (contractor will make his own arrangements for procuring water for testing) For:Heavy Duty GI pipe of 100mm dia
Providing & fixing Mechanical joints to cast iron pipes or Ductile iron pipes including cost of rubber gaskets and testing of joints. mechanical joints items will be supplied by the department. (contractor will make his own arrangements for procuring water for testing) for etc. complete 100mm dia pipes.
Providing & fixing Mechanical joints to cast iron pipes or Ductile iron pipes including cost of rubber gaskets and testing of joints. mechanical joints items will be supplied by the department. (contractor will make his own arrangements for procuring water for testing) for etc. complete 150mm dia pipes.
Providing & fixing Mechanical joints to cast iron pipes or Ductile iron pipes including cost of rubber gaskets and testing of joints. mechanical joints items will be supplied by the department. (contractor will make his own arrangements for procuring water for testing) for etc. complete 200mm dia pipes.
Providing & fixing Mechanical joints to cast iron pipes or Ductile iron pipes including cost of rubber gaskets and testing of joints. mechanical joints items will be supplied by the department. (contractor will make his own arrangements for procuring water for testing) for etc. complete 300mm dia pipes.
Providing, fabricaing and fixing at site various diameters of MS Flanges as per IS standards to fix sluice valves as per sketch. The rate to include cost of all materials, labour, consumables, hire charges for tools and tackles, weldiing equipments etc. complete as per instructions of the Engineer in charge for: Flanges of 100mm dia and 10mm thick.
Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two "O" rings and a coupler of suitable size, including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour, all lead and lift including encasing the Specials around to a depth of not less than 15cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing etc. Complte 75 MM ELECTRO FUSION COUPLER
Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two "O" rings and a coupler of suitable size, including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour, all lead and lift including encasing the Specials around to a depth of not less than 15cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing etc. Complte 90 MM ELECTRO FUSION COUPLER
Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two "O" rings and a coupler of suitable size, including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour, all lead and lift including encasing the Specials around to a depth of not less than 15cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing etc. Complte 75 MM ELECTRO FUSION Elbow
Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two "O" rings and a coupler of suitable size, including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour, all lead and lift including encasing the Specials around to a depth of not less than 15cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing etc. Complte 90 MM ELECTRO FUSION Elbow
Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two "O" rings and a coupler of suitable size, including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour, all lead and lift including encasing the Specials around to a depth of not less than 15cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing etc. Complte 90 X75 MM ELECTRO Fusion Reducer
Providing and installation of Class SN8 Double Wall Corrugated HDPE Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two "O" rings and a coupler of suitable size, including loading and unloading at both destination and cutting of pipes where ever necessary including jointing with all labour, all lead and lift including encasing the Specials around to a depth of not less than 15cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done the contractor shall have to make his own arrangement for procuring water for testing etc. Complte 100 ID COUPLER - fitting for 100mm dia pipes
Providing Ductile Iron Push on special confirming to IS 9523:2000 -Socketed D.I. Equal Tees 100mm X 100mm X100mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 -Socketed D.I. Equal Tees 150mm X 150mm X 150mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - Double Socketed with flanged Branch D.I. Un-Equal Tees 150mm X 150mm X 100mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All Socketed D.I. Reducers / Tapers 100 X 80 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All Socketed D.I. Reducers / Tapers 150 X 100 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All Socketed D.I. Reducers / Tapers 200 X 100 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged MJ COLLAR 100.00 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged MJ COLLAR 150.00 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged MJ COLLAR 200.00 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged MJ COLLAR 300.00 mm
Supplying of FIRE HOSE AS PER IS14933 IN 50MM DIA With Both side SS Gunmetal Coupling. Type A (Normal fire hoses, rubber lined or rubberized fabric lined, woven jacketed with or without elastomeric coating/covering for application under normal fire conditions with ISI Marked).
Supply and delivery of Centrifugal pumpset at site brand new best make and with discharge duty confirming to ISI standards and its latest amendments.2 HP, Size 50x40 Head 22M, Discharge 186 LPM
Supply and delivery of Centrifugal pumpset at site brand new best make and with discharge duty confirming to ISI standards and its latest amendments. 3 HP, size 50x40 Head 30M, Discharge 198 LPM
Supply and delivery of Centrifugal pumpset at site brand new best make and with discharge duty confirming to ISI standards and its latest amendments. 5 HP, size 50x40 Head 46M, Discharge 174 LPM
Supply and delivery of De-watering (Sewage) Pump, ETERNA 1500 CW+, 2 HP, Three Phase, 415 Volts, Size 50mm, to work site as per necessary ammendments and instructions of engineer incharge of work.
Hiring of De-watering (Sewage) Pump, ETERNA 1500 CW+, upto 5 HP, Three Phase, 415 Volts, Size 50mm, to work site as per necessary ammendments and instructions of engineer incharge of work.
Supply of PPR Pipe Clamp confirming to IS 15801-2008 and DIN Standards 8077/8092 (PPR Pipe Clamp 25mm)
Supply of PPR Pipe Clamp confirming to IS 15801-2008 and DIN Standards 8077/8092 (PPR Pipe Clamp 32mm)
Supply of PPR Pipe Clamp confirming to IS 15801-2008 and DIN Standards 8077/8092 (PPR Pipe Clamp 40mm)
Supply of PPR Pipe Clamp confirming to IS 15801-2008 and DIN Standards 8077/8092 (PPR Pipe Clamp 50mm)
Supply of PPR Pipe Clamp confirming to IS 15801-2008 and DIN Standards 8077/8092 (PPR Pipe Clamp 63mm)
Providing and fixing bolts including nuts and washers complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge
Providing and fixing Rubber Gasket SBR Quality 100mm dia
Providing and fixing Rubber Gasket SBR Quality 150mm dia
Providing and fixing Rubber Gasket SBR Quality 200mm dia
Providing and fixing Rubber Gasket SBR Quality 300mm dia
Replace the components of submersible pump sets, requiring replacements decided by the departmental officials, with respective make of damaged ones, including all materials, labour, equipments and testing etc.(with gurantee of period not less than 1 year) for: The Oil Seal
Replace the components of submersible pump sets, requiring replacements decided by the departmental officials, with respective make of damaged ones, including all materials, labour, equipments and testing etc.(with gurantee of period not less than 1 year) for: The Oil Seal.and steel bush
Supply of new roller/ thrust bearing ( make SKF / FAG/NBC or equivalent with ISI /ISO specification ) after removing the old bearing
Replace the components of submersible pump sets, requiring replacements decided by the departmental officials, with respective make of damaged ones, including all materials, labour, equipments and testing etc.(with gurantee of period not less than 1 year) for: The Impeller (Shell moulded with aluminium and bronze.)
Providing terminal plate as per ISI specifiction with guarantee period of not less than 12 months (Terminal plate upto 7.5HP to 12.5 HP)
Providing terminal plate as per ISI specifiction with guarantee period of not less than 12 months (terminal plate 15HP to 30HP )
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged Socketed, D.I. Flanged Spigot, MS End Plates D.I. Flanged Socketed 100.00 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged Socketed, D.I. Flanged Spigot, MS End Plates D.I. Flanged Spigot 100.00 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged Socketed, D.I. Flanged Spigot, MS End Plates D.I. Flanged Spigot 150.00 mm
Providing Ductile Iron Push on special confirming to IS 9523:2000 - All D.I. Flanged Socketed, D.I. Flanged Spigot, MS End PlatesD.I. Flanged Spigot 200.00 mm
Supply and fixing of 4 pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947. 32 A
Supply and fixing of 4 pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947. 40 A
Wiring for lighting/power circuit using one of FRLSPV Cinsulated1100V grade,multistr and copper wire with low conductorres is tancesingle core in open or concealed system of wiring with specified IS-694:2010 4 mm2
Wiring for lighting/ power circuit using one of FRLSPV Cinsulated 1100V Grade,multistrand copper wire with low conductorresistan cesingle coreinopen or concealed system of wiring with specified IS-694:2010 6 mm2
Wiring for lighting/ power circuit using one of FRLSPV Cinsulated 1100V grade ,multi strand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS-694:2010 10 mm2
Wiring fo rlighting/ power circuit using one of FRLSPV Cinsulated1100V grade, multistrand copper wire with lowc onductorresistan cesingle coreinopenor concealed system of wiring with specified IS-694:2010 16 mm2
Supplying and fixing Micro processor based Electronic timer (withoutcontactor, Din Mounting using necessary bolts ,nuts and washersetc.,.) 3-120 sec setting.
Supplying and fixing Moulded Case Circuit Breaker (MCCB over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, hand leand wiring complete. Protection of Over loadand Short circuit with adjustable thermalmagnetic release, Microprocessorr elease shall have Earth Fault as per IS/IEC60947-2.(Icu=100lcs). In4PMCCB,all Poles should have protection for Shor tCicrcuit/OverLoad. For Microprocessor MCCBS Facility for segregating Priorityand Non-Priority loads must be available in the MCCB. MCCB shall be provided with double in sulation (insulation between front coverandinternal power circuit stoavoidany accidental contact with live current carrying path with the front coveropen). Multi-pole breakers shall be designed to break all the pole ssimultaneously and they shall have a single mechanism. 100 A 25 Ka FOUR Pole,
Supplying & fixing miniature circuit breakers on existing MCB distribution board susing necessary fixing material sand'C'Type curve ,indicatorON/OFF, energy cross-3 with Short circui breaking capacity of 10K and complete wiring as required confirming to IEC60898.
Supplying & fixing miniature circuit breakers on existing MCB distribution board susing necessary fixing material sand'C'Type curve ,indicatorON/OFF, energy cross-3 with Short circui breaking capacity of 10K and complete wiring as required confirming to IEC60898.6-32 A TPN
Supplying & fixing miniature circuit breakers on existing MCB distribution board susing necessary fixing material sand'C'Type curve ,indicatorON/OFF, energy cross-3 with Short circui breaking capacity of 10K and complete wiring as required confirming to IEC60898.6-32 A DP,
Supplying & fixing miniature circuit breakers on existing MCB distribution board susing necessary fixing material sand'C'Type curve ,indicatorON/OFF, energy cross-3 with Short circui breaking capacity of 10K and complete wiring as required confirming to IEC60898. 6-32 A SP
Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440VAC. 50 Hz 12/24V D.C.
Supplying ,erecting, testing & commissioning of ON-LINE UPS system suitable for operationon 230V,50Hz, A/C supply, with isolation transformer all accessories complete and Excluding batteries and wiring complete.
Supplying of multifunction digital meter with three line backlight LCD type display for voltage ,Current ,frequency, Power, power factor ,kVA, kWH, kVAR suitable for 3phase, 4wire LT network with IP54 degree of protection and completely wired as required with communication Port and Class 0.5s accuracy
Supplying push button operated direct online starter with an anti weld silver cadmiumoxide contactor with replaceable fixed and moving contacts and bimetallic thermal over load relay help in anticorrosion treated sheet steel or iron clad enclosure and fixing the same to suitable capacity wires for 230/440 V 1/3 phase motor upto 5 HP.
Supply and fixing of 4 pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS-13947. 22/25 A
Supplying of Contactors 3 Pole DC Low Consumption 9 Amp
Supplying of Contactors 3 Pole DC Low Consumption 18 Amp
Supplying of over Load relay 7 A to 10A
Supplying of over Load relay 9A to 13 A
Supplying of over Load relay 16A to 24A
Supplying of 2CO 8 pin relay Standar Cover lockable test button ( 230 V AC)
Supplying of ADD on Block additional instantaneos auxiliary contact block 1 No+ 1NC
Supplying of ADD on Block additional instantaneos auxiliary contact block 2 No+ 2NC
Supplying of illimnated push butons Flush integral LED 230V AC Green/Red/Yellow
Supplying fully automaticstar-delta starter unit push button type with suitable wires, 3contactors, one adjustable thermal timer mounted on acommon base plate heldin steel enclosure for use on400/440V3 phase and wired after fixing to the existing wooden board for motor. Above 25 HP upto 35 HP
Supplying of CONTACT 20/30 MFD Motor Running Capacitor 440 VAC
Supplying of CONTACT 36/50 MFD Motor Running Capacitor 440 VAC
Supplying fully automatic star-delta starter unit push button type with suitable wires, 3contactors, one adjustable thermal timer mounted on acommon base plate heldin steel enclosure for use on400/440V3 phase and wired after fixing to the existing wooden board for motor. upto 12.5 HP
Supplying fully automaticstar-delta starter unit push button type with suitable wires, 3contactors, one adjustable thermal timer mounted on acommon base plate heldin steel enclosure for use on400/440V3 phase and wired after fixing to the existing wooden board for motor. Above 12.5 HP upto 25 HP
Global Tech Services (BID ID -3261432)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .