BMSICL/Infra/09/2026 GR-07, Construction of Additional Primary Health Center (APHC) With Staff Quarter at-Nauma, Block-Halsi, Dist.-Lakhisarai

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead

Supplying and filling in plinth with local sand under floors including, watering, ramming consolidating and dressing complete.

Providing desination 100 A one brick flat soling joints filled with local sand including cost of watering texes, roualty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutering-all work upto plinth level.

1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregate 40mm nominal size)

1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 40 mm nominal size)

1:4:8 ( 1 cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size)

Brick work with bricks of class designation 100A in foundation and plinth in:

Extra for Brick work in superstructure above plinth level upto floor V cum.

Half brick masonry with brick of class designation 100A in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level upto V floor level.

Extra for providing and placing in position 2Nos. 6mm dia. MS bars at every third third course of half brick masonry (with F.P.S. brick)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mmnominal size, well rammed and consolidated and grouted withfine sand, including finishing the top smooth

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg. per square metre on damp oroof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying in position specified mix of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement -all work upto plinth level..

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns etc.for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces.

Edges of slabs and breaks in floors and walls

Providing,precast cement concrete Jali 1:2:4(1 cement:2 coarse sand:4 stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:3 fine sand) etc.complete excluding plastering of the jambs, sills and soffits.

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets.

Thermo-Mechanically Treated bars TMTC-500-8mm dia

Thermo-Mechanically Treated bars TMTC-500-10mm dia

Thermo-Mechanically Treated bars TMTC-500-12mm dia

Thermo-Mechanically Treated bars TMT Fe-500- 16,20,25mm dia

Providing average 150mm thick dry rammed khoa beaten to 112 mm (compacted with water) made of well burnt or jhama bricks including ramming property till compacted thickness is achieved, curing and carriage of water with all leaads, making proper slope and blinding the with cement mortar(1:10)all complete as per building specification and direction of E/l.

Brick Aggregate (Single size) 50 mm nominal size

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

30 mm thick including Stainless Steel butt hinges with necessary screws.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 TypeS, including cost of adhesive of approved quality. 1.0 mm thick

Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and fixing M.S. sliding door bolts bright finished or/and black enamelled,with nuts and screws etc.compelled:

each sb

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass hangging type floor door stoper with necessary screws etc. compelte.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding tower bolt (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with nuts screws etc. necessary screws etc. complete.

Providing and fixing anodised aluminium work for doors, windows, ventilators and partitions with extuded built up standard tubular and other sections of approved make conforming to IS: 733 and IS: 1285, anodised trasparent or dyed to required shade according to IS: 1868. (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust fre straight, mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/paneling, C,P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately.)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing 18 mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels.

Area of each slab over 0.2sqm but upto 0.5 sqm Granite of any colour and shade

Extra for providing edge moulding to 19 mm thick marble stone counters, Vanities etc. over item no. 8.2 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. Granite work

Extra for fixing marble / granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture) of approved make in all colours, shades except begundy, bottle green,black of any size as approved by Engineer-in-chage in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 (1 Cement:3 Coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300 x 300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20mm thick Cement Mortar 1:4 (1 Cement: 4 Coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

20 to 25mm thick

Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm

12mm cement plaster of mix:

20mm cement plaster of mix :

6mm cement plaster to ceiling of mix:

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

Providing and fixing circular cast iron box for ceiling fan clamp 140mminternal dia, 73 mm height,.5 mm thick rim bottom and top lids, 1.5mm thick M.S sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron box by means of 3.3mm dia. round headed screws, one pcl at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing pressed steel door confirming IS code 351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if requird angle threshold of mild steel angle of section 50x25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. all comlete.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm ( ± 0.2 mm) , corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer’s specification and direction of Engineer-in-charge.

Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x 20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer’s specification and direction of engineer-incharge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Demolishing 1:3:6 or richer mix cement concrete including disposal of material within 50 metre lead:

Demolishing brick work In cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead:

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Making 25 cm (10") dia bore up to 4 mtr depth below ground with hand auger of approved quality in ordinary soi! (vide classification of soil item A ) true to plumb and without eccentri city in any stage of operation and disposal of the excavated earth up to 50 mtr , Lead in eluding all lifts , all complete as per approved disign and direction of E/l Details of cost for 4 piles of 4 m= 16 mtrs depth )

63 CM (25) UNDER -REAM Making 63 cm (25) dia under ream at required with hand auger of approved quality in ordinary soil (vide classification of soil ifem - A) true to plumb and without eccentri city in my stage of opration and disposal of the excavated earth up to 50 mts lead in eluding all lifts , all complete as per approved design and direction of (E/l)

Stone chips [Koderma By Road1 1K +132P KM]

Bricks

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing C.P. brass toilet paper holder :

Providing and fixing wash basin with C.I. rackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, ncludingpainting of fittings and brackets, cutting and making good the walls wherever require :

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers. (In O.T.)

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the all wherever required :

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing G.I pipes complete with G.I fittings including trenching and refilling etc.

Metre

Metre

Metre

Metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15 mm nominal outer dia Pipes

20 mm nominal outer dia pipes

Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15mm nominal bore

25mm nominal bore

32mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 100A.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

per litre

Providing and fixing C.P. brass , bib cock of approved quality conforming to IS : 8931

Providing and fixing C.P. brass long body, bib cock of approved quality conforming to IS standard and weight not less than 690 grams.

Providing and fixing C.P brass angle valve for basin mixer and gyser point of approved quality conforming to IS : 8931

metre

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage)

150 mm dia RCC pipe

250 mm dia RCC pipe

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge.

100 mm nominal size dia.

150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (RMS) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

metre

`Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate,suitable GI box and earthing the point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable etc. as required.

Point

Supplying and fixing suitable size GI box with modular plate and cover including providing and fixing 3 pin 5/6 Amp modular type socket on switch/separate board (in surface / recessed PVC conduit wiring system) and 5/6 Amp modular type switch Earthing the 3rd pin, painting etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover including providing and fixing 6 pin 20/16 Amp modular type socket on switch/separate board (in surface / recessed PVC conduit wiring system) and 20/16 Amp modular type switch ,connection, painting etc, painting etc. as required. For Power Plug.

Wiring for power plug with 2 x 4 Sq.Mm. FRLS PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 no 4 Sq.Mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor single core cable in surface/ recessed medium class PVC conduit as required

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Wiring for twin control light point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable in Surface/ recessed medium class PVC conduit, 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/power plug with 4 x 4 Sq.Mm. FRLS PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 2 nos. 4 Sq.Mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying & fixing 4 way (4 +12) three pole and neutral, sheet steel MCB distribution board 415 volts on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, hinged front acrylic cover for the MCB knobs, detachable gland plate, interconnections, phosphatised and powder painted earthing etc. as required.(without MCB's)

Providing and fixing 6 way(4+18), TP & N prewired, sheet steel, MCB DB,415 volts, on surface/ recess double door complete with loose wire box, terminal blocks, duly prewired with suitable size PVC insulated copper wire up to terminal blocks, tinned cooper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc.as required. (But without MCB / RCCB Isolator) .

Providing and fixing 8 way(4+24), TP & N prewired, sheet steel, MCB DB,415 volts, on surface/ recess double door complete with loose wire box, terminal blocks, duly prewired with suitable size PVC insulated copper wire up to terminal blocks, tinned cooper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc.as required. (But without MCB / RCCB Isolator) .

6/32 A SPN MCB 'C' series

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface / recess, complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate bus bar, interconnections, powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator)

Supply and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required :(for all Elec & LV services)

Earthing with copper earth plate 600mmX600mmX3mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. as required.

Earthing with GI earth plate 600mmX600mmX6mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/cable as required

Providing and fixing 25mm x 5 mm G.I strip on surface or in recess for connections etc. as required.

Supplying and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connecion with copper thimble excavation and refilling etc. as required.

75 mm.X 75 mm.X 50 mm. deep ( 4"X4")

Telephone socket outlet

T.V. antenna socket outlet

Providing and fixing M.V. danger notice plate of 200mmx150mm made of mild steel, atleast 2mm thick and vitreous enamelled white on both sides and with inscription single red colour on FRLSont side as required.

Supplying and fixing call bell/buzzer suitable for single phase, 230 volts, complete as required.

supply and installations of regular/standard model AC cieling fan of 1200 mm sweep including wiring the down rods of standard length upto 30 cm with 1.5 sqmm FR PVC insulated copper conductor etc as required.

Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

supply and Installation of 300 mm 230 V AC exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required

Supply, fixing of following types lamp inthe existing electrical fitting/fixtures etc as required. 18 watt CFL lamp.

Supply, and fixing single wall mounted 20/22 watt LED type baten fitting complete with electronic driver and LED tube etc directly on wall/cieling including connections with 1.5 sqmm FR PVC insulated copper conductor and earthing the body etc as required.

Supply and installation of 40 mm, 23V AC 230/250 volts, 50 HZ Wall/Cabin fan including fixing the bracket, making connections testing commissioning etc as required

Specification

Providing and filling (Back filling) profile "B" pressed steel door frame back hallow portion with cement concrete mix of 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 10mm nominal size)

Providing and fixing, uPVC pipes 6 Kg/Cm2 (IS: 4985) including all fittings (plain or door) e.g. bends, junction, offsets, access pieces, jointing with rubber ring/solvent cement joints including required suports,cutting chase or holes in walls and floors and making good where required.

Providing & fixing in position uPVC P"or S" trap/elbow of self cleaning design of following sizes for the embedded areas. Making proper connection with drip-seal joints, cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors where required.

Providing and fixing multi-floor trap fitting with maximum 3 inlets 32,40 or 50 mm size fabricated from 100/150 mm dia upvc pipes and sockets,fixed to C.I. trap with lead caulked joint and set in cement concrete as per standard drawing complete.

Providing and fixing END CAP or cleanout plug( Ceiling or Floor) with suitable inset keys for opening, male threaded joint with socket fixed to pipe complete in all respects.

Supplying & Installation of suitable 2Hp submersible pump B.S or K.S.B or equivalent make with finolex cable 1x3x2.5 squmm(upto 75mtr) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as MCB of 0-25Amp (Havell or Indocopp or MDS make), Volt & Ampere meter (AE make), single phase preventer (Minilac or VSP -1 make) starter (L&T or BCH make) etc of approved make, 40mm HDPE Pipe (25 mtr) and all accessories complete as per requirement of site.

Fabrication, supply, installation, testing and commissioning of cubicle type wall mounted L.T. panel made out of 16mm thick CRCA sheet including connection, inter-connection along with 4 strip aluminium bus bar as per CP WD specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel mounting switchgears etc. as required.,

High Back Revolving Chair having Seat and Back made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. HIGH BACK SIZE: 47.5 cm (W) x 69.5 cm (H) SEAT SIZE: 47.0 cm (W) x 48.0 cm (D) POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: 360° revolving type, Upright position locking, Tilt tension adjustment & Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt) PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5nos. twin wheel castors. The pedestal is 66.0cm pitch-center dia. (76.0 cm with castors.) TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

Office Table of Size : 1365mm (W) x 680mm (D) x 735mm (H) with 18mm thk. Pre-Laminated Board (PLB). Under-Structure : Square shape MS Section duly powder coated. Modesty Panel - Metal Modesty Storage : Drawer Unit (2D+1F) made up of 18mm thick Prelaminated particle board with PVC edge banding on exposed edges.

S/F/F Chair (Make IKEA / HERMAN MILLER/ GODREJ / HAWORTH) Size : Depth (D) - 57.0 cm Width (W) - 58.0 cm Height (H) - 88.0 cm Seat Height (SH) - 45.0 cm SEAT/BACK ASSEMBLY : The seat and back are made from chemically treated and seasoned wood, caned and finished with synthetic paint (Colour: Black with matt finish). *BACK SIZE: 45.1CM(W) X 39.0CM(H). *SEAT SIZE: 45.1cm(W) x 42.4cm(D). CANE FOR SEAT/BACK: Cane is made from mix of LDPE + HDPE Mix Material. The caning used for seat/back has high tensile strength as per IS: 5378 Part II, 1990. Cane breaking strength = 3000 Kg/cm 2 (min.) % Elongation at break =25%. ARMREST TUBE : The armrest tube is made of M.S. E.R.W. tube dia. 2.54cm. (1”) x 16BG thick and welded to the understructure assy. ARMREST : The armrest is gas-assisted injection moulded from black Polypropylene. UNDERSTRUCTURE ASSEMBLY : The understructure assembly is a cantilever type frame made of dia. 2.54cm. (1”) x 14BG. thick M.S. E.R.W. tube and powder coated.

Table Size: 1199 x 590 x 735 mm having top made of 18 mm thick superior quality pre-laminated particle board of Grade II Type II conforming to IS:12823 of approved quality and shade. The edges of the table shall be banded with PVC strip 2 mm thick using hot melt glue under heat and pressure. The table top shall be supported by 1 mm thick M.S. ‘C’ frame stiffener of size 24.2 mm (W) x 38 mm (H). The table shall have 4 legs made of Electric Resistant Welded prime quality CRCA steel round tubular frame of Dia. 25.4 mm size and of 1.2 mm thickness. The base of legs of the tables shall be covered with plastic caps. The table shall have one no. drawer units i.e. right side drawer unit shall have three box drawers. And overall size of drawer 355 mm (W) x 560 mm (D) x 430 mm (H). The drawer unit shall be made of 0.8 mm thick CRCA sheet and drawer trays shall be made of 0.6 mm thick CRCA sheet. The drawers shall glide on frictionless slides of 1.2 mm thick CRCA sheet and shall have a multi purpose steel lock with handles built in place. The drawer units to have a mechanism to ensure only one drawer opens at a time. Both the drawers are fitted to ‘C’ frame by machine screws. Joints shall be interlocked and welded to render a flawless appearance. All steel parts shall be pretreated for seven stage anti-corrosion treatment followed by powder coating of thickness 50–55 microns.

Overall Sizes (L)2065 mm x (W)850 mm x (H) 850 mm Material Specifications 1 Leg Frame - Made from E.R.W Tube of section 30 x 30mm and thickness 1.6 mm 2 Intermediate Frame - Made from E.R.W Tube of section 30 x 30mm and thickness 1.6 mm 3 Leg Shoe - Made from NYLON 6 (To avoid wear and sound) 4 Lying surface - Made from CRCA Sheet of thickness 1.2mm 5 Rachet - Made from M.S of thickness 5mm (Provides the back rest tilt 0°, 15°, 30° adjustment positions. 6 Bowl Stand - Made from S.S. 304 of section Ø15.9 7 S.S. Bowl - Made from S.S. 304 (To collect the fluids during the procedure) 8 Head Rest - Made from CRCA Sheet of thickness 1.2mm 9 Calf Rest - Made from Leathrite (Leatherite wth PU Foam and MS backing Sheet) 10 Lithotomy Rod - Made from SS 304 (To provide variable height & swivel position as per desired position) Finish Specification 1 Powder Coating - Epoxy polyester powder coating 2 Colour - Ral white, plastic parts in Gray Performance Specification Maximum Patient load - 135Kg

Overall Sizes: (L)2268 mm X ( W)922 mm X (H) 610 mm Description: Sheet Bed should be a plain bed used in the recovery ward. Material Specifications: Under Structure has a Higher diameter tube which should provide a sturdy understructure. Lying surface area of CRCA Finish Specifications: Head Board/Leg Board should be made of frame MS ERW RoundTube of sections Ø19, Ø25.4& Ø31.75mm, of thickness1.6 mm Provision for mounting of IV Pole and Mosquito Net pole should be present Finish Specifications: Powder coating should be Bacteriostatic and thermosetting epoxy Polyester, formulated to fulfill the requirements for bacterial protection. All powder coated parts in RAL white Performance Specifications: Maximum patient load should be 135 kg

Thickness-Mattress: 3"+ SANDWITCH CONSTRUCTION: Round corners - YES Hitlon thickness ( MM): 60 Hitlon density (Gm/dcm3): 23 Coir(Both side) Thickness MM: 20 Density (Gm/dcm3): 70, DRC (%): 22 QUILTING - COMBINATION / LAYERS: Pilled Foam – Quilting (One Side) Thickness MM - 14 Pilled Foam Density Gm/dcm3 - 18 PU foam / EPE sheet side walling Thickness MM - 3 TOTAL MATTRESS THICKNESS-MM - 87 REXINE (GSM): 150 Note: * Finish product thickness should be measure from outer to outer surface. Tolerance +5 mm

Dimension: Top Size - 760 (L) x 360 (W) x 850 (H) mm Featured with Laminated board top extending over the width of the bed, Tubular Frame work with 50mm Dia. Non-rusting Castors, and Pre-treated and Powder Coated.

Overall Sizes in mm: 1500 (L) x 850 (W) x 1210 (H) Flat single section bed with grille frame on 4 sides. Suitable for children up to 12 years. Drop down grill frame on both sides for protection of the patient. Material Specifications: Under Structure has a Higher diameter tube which should provide a sturdy understructure. Lying surface area of CRCA Finish Specifications: Head Board/Leg Board should be made of frame MS ERW RoundTube of sections Ø19, Ø25.4& Ø31.75mm, of thickness1.6 mm Provision for mounting of IV Pole and Mosquito Net pole should be present Finish Specifications: Powder coating should be Bacteriostatic and thermosetting epoxy Polyester, formulated to fulfill the requirements for bacterial protection. All powder coated parts in RAL white

Bonded Foam Mattress of Thickness 3" Size: 1415 x 785 x 75 MM

Three fold screen is a portable screen on castors having three screens which can be folded to provide privacy in recovery ward. Overall Sizes (L)2637 mm X ( W)640 mm X (H) 1720 mm Material Specifications 1 Fix Frame - Made from E.R.W Tube of Section Ø25.4 having Thickness 1.2 mm (To provide hinging to movable frame) 2 Movable Frame - Made from E.R.W Tube of Section Ø19.05 having Thickness 1.2 mm (Flexible frame has plastic hinge. It can be adjusted in provided space) 3 Leg Frame - Made from E.R.W Tube of Section SQ. 30 having Thickness 1.6mm 4 Caster Wheel - Of Section Ø50 (For Ease of movement) 5 Bush For Holding Pipe - Made from Nylon 6 (Plastic bush) 6 Screen - Casement fabric for screen which is opaque for providing modesty. Finish Specifications 1 Powder coating - Epoxy polyester. 2 Color - Powder coated parts in RAL white, Plastic parts in Gray (Pantone cool gray 8C), Casement fabric in green (RAL 6026)

Providing and installation at site ,Drip Stand with 4 hooks,height adjustable up to 130 cm to 230 cm, made of SS Steel Verticle tubes,fitted to SS five prolonged base,mounted on 5 cm swival twin castors.

Description - 4 legged basin stand mounted on castors. Overall Sizes- Base circle dia 425 X (H) 850mm. Material Specification: Stand - SS 304 tube of section 12.7mm & 25.4 mm thickness 1.2mm, Bowl - SS 202 sheet, spin section, thickness 0.8mm. Castors - High endurance Plastic injection moulded castors, 50mm in dia. Finish Specification - SS (Buffed) glossy mirror finish. Performance Specification - Maximum safe working load 20 Kg.

Description - Oxygen Cylinder Trolly is mounted on castors. Size - L-410mm X W-375mm X H-1112mm. Material Specification : Main Frame - MS ERW Tube, Section 25.4mm Thickness 1.6mm for holding the cylinder. Locking Rod -MS Rod, section 10mm, keeps the cylinder in position during transit. Base Frame -MS ERW Tube, section 25.4 X 25.4, thickness - 1.6mm, sturdy base for resting the cylinder. Castor Wheel -PU wheel, section 100mm, thickness 25mm, for ease of movement. Leg Cap -LDPE, to cap the open ends at the bottom. Finish Specification-RAL White, epoxy polyster powder coating, plastic parts in pantone cool grey 8c. Performance Specification -Maximum safe working load 50 Kg.

Material Specification - Top Shelf - SS 304 Sheet, thickness 1mm, Supporting Legs -SS 304 tube, section 31.8mm pipe, thickness 1.2mm, Horizontal Bar - SS 304 Tube, section 12.7mm, thickness 1.2mm, welded with the legs. Bottom shelf - SS 304 Sheet, thickness 1mm. Castors - High endurance, Plastic injection moulded castors, section 125mm. Finish Specification - SS buffed to Glossy mirror finish. Performance Specification - Maximum safe working load 20 Kg.

Description - Stretcher on trolley is a removable stretcher mounted on a sturdy trolley having castors for ease of movement.Overall Size - (L)2005 mm x (W) 620 mm x (H)790 mm. Material Specification - Trolly - ERW Tube, Section 31.75 & 25.4mm, Thickness - 1.6mm, Provides the base to rest the stretcher on its four resting pads. Holder for Stretcher - MS with rubber pad, Used to hold the stretcher in position on to the trolly. Castor Wheel - 200mm dia Wheel with diagonal lockable castor. Stretcher - ERW Tube, Section 25.4mm, Thickness 1.6mm, Removable from Trolly to provide flexibility of reach. Stretcher Top Sheet - CRCA Sheet, Thickness - 1.2mm, Contoured stretcher top provides safety to patient during handling. Powder Coating - Epoxy Polyster. Colour - MS Part in RAL White Powder Coating, Plastic parts in Pantone cool grey 8C. Performance Specification - Maximum Patient Load 135 Kg.

Seat and back easily removable and replaceable. Fine and durable upholstery for seat and back. Nylone Handgrips and Padded arm rest. Polished SS constrct. Solid tire wheels with Rear wheel lock. Aluminium leg rest-swing away type. All the stainless steel should be seamless conforming to 304 grade/16 gauge and polished finished.

3 Seater Chair with following specification: Seat Shell - Seat shell is welded assembly of seat, Back & side frame. Seat & back are made of 0.12±0.013cm thk CR steel sheet with oblong perforations. They are welded to side frame of size 3.2±0.05cm X 0.5±0.05cm thk HR steel. Welded assembly is powder coated (DFT 40-60 microns). Seat has a front warefall edge for comfortable seating and also has a buttock support curve. Understructure Assembly - Consists of connecting beam & leg assembly made of MS ERW oblong tube size 7.5±0.03cm X 5.0±0.03cm X 0.02±0.016cm thk and is powder coated (DFT 40-60 microns). Leg assembly is fitted with shoes and levellers in Nylon. Leg assembly is designed with minimal area of contact close to ground providing easy access for cleaning purposes. Connecting beam is fitted with snap locking end capfor side by side understructure alignment. Arm Rest Assembly - Consists of arNSIest frame & arNSIest pad.ArNSIest frame is made up of size 3.175±0.05cm X 0.47±0.027 cm thk HR steel and is powder coated (DFT 40-60 microns). ArNSIest pad is injection moulded in nylon and is fitted onto the arNSIest frame.

Size - 1980mm (H) X 916mm (W) X 486mm (D), Construction & Material - Welded Construction, 0.7mm thick (±0.07mm) CRCA (D Grade as per IS:513) for shelf, 0.8mm thick (±0.08mm) High yield strength (D Grade High yield Strength as per IS:513) CRCA for Doors & Back, 0.9mm thick (±0.08mm) CRCA (D Grade as per IS:513) for all other components. Locking & Handle - Mazak Handle, Three way locking mechanism with shooting bolt. Shelving - Height wise adjustable shelf mounting, Uniformly distributed load capacity per each full shelf is 40 Kg maximum, 4 Nos. adjustable full shelf, Leveler - M10 Screw type leveler with hex plastic base.Finish - Epoxy powder coated to the thickness of 50 microns ( ±10)

Load bearing members of the system should be made out of High strength HR steel having properties equivalent to grades specified by IS 5986:2002 / IS 2062:2006 In addition to high strength, the raw material used for structural load bearing members also should possesses adequate ductility to ensure toughness. The material should also have the necessary impact strength for cold room applications upto -30° C Surface finish: All components must have thorough anti-rust treatment to prevent corrosion, thereby increasing the life of the component. Steel components must be powder coated for obtaining a smooth, scratch resistant and a lasting attractive, finish. The Dry Film Thickness (DFT) of 35 microns is required on an average after Powder coating. All components are to be an elaborate 4 step, six zone anti corrosion treatment, viz. De-greasing as per IS 6005:1970, Rinsing, Phospating as per IS 3618:1966 and De-mineralized water rinsing. Angle: Vertical load carrying member that transfers load to the ground via base plates, its Material Specifications should be as per IS: 5986 (ST 42). Angles should be of rolled formed construction to ensure minimal residual stresses and accuracy throughout the length of the angles, and should take the designated load. Slots at every 19.05 mm for height optimisation or adapt to ever changing SKU sizes and Grouted through base plates. Surface Finish: Epoxy-Polyester Powder Coated – Lead Free BS Grey/Oxford Blue in colour. Panel: Should conform to IS:513 D, and minimum yield strength 210 MPa. No. of bends : 6 Manufacturing : Press forming. Panels are to be provided with lipped flanges. Width of the flange being 31 mm and depth of lip 17 mm. Panels are provided with 9 mm holes on the flange for corner plates, cladding sheets. Design Criteria : Deflection to be under SEMA guidelines. Surface Finish : Epoxy-Polyester Powder Coated – Lead Free BS Grey/Oxford Blue in Colour. SIZE: Width : 3 ft Depth: 18” Height: 6’ Load Capacity : 90 kg / loading level UDL (Uniformly Distributed Load)

Providing and installation at site of Revolving Stool with stainless steel top, with pneumatic height adjustment and moulded five pronged mobile base with 5cms swivel twin castors as required.. • Height Adjustable: 48 to 60 cms.

Overall size 402 mm(L)x404 mm(W)x835 mm(H)-Locker with one cabinet with stainless steel,rest structureis in MS powder coated ,cabinet provided with cam lock.It has ERQ sq tube structure of 25.4 mm Sq section of 1.6 mm thickness.Shoe is made up of PVC+nitrrile and top is SS 304 sheet with 0.8 mm thcikness and cabinet of CRCA of 1 mm thcikness.Handles are ABS.Powder coated epoxy olyster,rubber and plastics parts in grey,SS top buffered mirror finish.The manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products

Description The examination table made of sturdy structure. The backrest has a ratchet mechanism for tilting the backrest. Overall Sizes L - 1830 mm x W. - 600 mm x H. - 850 mm Material Specifications 1. LegFrame - MSE.R.WTube 30x30 Thickness 1.6mm 2. Intermediate Frame - MS E.R.W Tube 30 x 30 Thickness 1.6mm 3. Leg Shoe Nylon 6 (To avoid wear and tear) 4. Lying surface - MSS. Sheet Thickness 1.2mm 5. Ratchet - M.S plate Thickness 5mm (Provides the bask rest tilt 0°, 15°, 30° adjustment positions. Finish Specifications: 1. Powder coating Epoxy polyester. 2. Color RAL white, Plastic parts in Gray (Pantone cool gray 8C) Performance Specifications Maximum safe patient Load - 135 Kg.

Thickness-Mattress: 3"+ SANDWITCH CONSTRUCTION: Round corners - YES Hitlon thickness ( MM): 60 Hitlon density (Gm/dcm3): 23 Coir(Both side) Thickness MM: 20 Density (Gm/dcm3): 70, DRC (%): 22 QUILTING - COMBINATION / LAYERS: Pilled Foam – Quilting (One Side) Thickness MM - 14 Pilled Foam Density Gm/dcm3 - 18 PU foam / EPE sheet side walling Thickness MM - 3 TOTAL MATTRESS THICKNESS-MM - 87 REXINE (GSM): 150 Note: * Finish product thickness should be measure from outer to outer surface. Tolerance +5 mm

Medicine Trolley Overall Sizes L - 532 mm x W. - 902 mm x H. - 915 mm Material Specifications Mild Steel Epoxy Powder Coated Framework Stainless Steel Shelves Two Drawers under the each shelf On costars.

Providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. Duly anodised all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints of appropriate size all complete as per diirection of Engineer in Charge.

Wall Mounted, 450x100mm

Door Mounted, 300x80mm

Illuminating Direction retroreflective 450mm Dia signage with MS suppurt

6 KG ABC Fire Extinguisher

Period of Bid Validity

Cost of Bid Document (in Rs)

Pratap Kumar

D- 619, Jyotipuram Apartment, Jagdeopath Chouraha, Bailey Road, P.O.- B.V.College, P.S.- Shastri Nagar, Patna-800014

Amount (Rs)

Group A Tedered Rate comparison to B.O.Q.Amount in Figure

Twenty One Point Five Nine Percent Below

Below

Rupees One Crore Forty Five Lakh Seventy Eight Thousand Two Hundred Ninety Eight and Forty Eight Paise Only

Group B (Item rate) total amount in Figure

Rupees Twelve Lakh Fourteen Thousand Two Hundred Seventy Only

Rupees One Crore Fifty Seven Lakh Ninety Two Thousand Five Hundred Sixty Eight and Forty Eight Paise Only

DESCRIPTION OF ITEMS

B. Wall

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead

Supplying and filling in plinth with local sand under floors including, watering, ramming consolidating and dressing complete.

Providing desination 100 A one brick flat soling joints filled with local sand including cost of watering texes, roualty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutering-all work upto plinth level.

1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregate 40mm nominal size)

1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 40 mm nominal size)

1:4:8 ( 1 cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size)

Brick work with bricks of class designation 100A in foundation and plinth in:

Extra for Brick work in superstructure above plinth level upto floor V cum.

Half brick masonry with brick of class designation 100A in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level upto V floor level.

Extra for providing and placing in position 2Nos. 6mm dia. MS bars at every third third course of half brick masonry (with F.P.S. brick)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mmnominal size, well rammed and consolidated and grouted withfine sand, including finishing the top smooth

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg. per square metre on damp oroof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying in position specified mix of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement -all work upto plinth level..

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns etc.for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces.

Edges of slabs and breaks in floors and walls

Providing,precast cement concrete Jali 1:2:4(1 cement:2 coarse sand:4 stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:3 fine sand) etc.complete excluding plastering of the jambs, sills and soffits.

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets.

Thermo-Mechanically Treated bars TMTC-500-8mm dia

Thermo-Mechanically Treated bars TMTC-500-10mm dia

Thermo-Mechanically Treated bars TMTC-500-12mm dia

Thermo-Mechanically Treated bars TMT Fe-500- 16,20,25mm dia

Providing average 150mm thick dry rammed khoa beaten to 112 mm (compacted with water) made of well burnt or jhama bricks including ramming property till compacted thickness is achieved, curing and carriage of water with all leaads, making proper slope and blinding the with cement mortar(1:10)all complete as per building specification and direction of E/l.

Brick Aggregate (Single size) 50 mm nominal size

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

30 mm thick including Stainless Steel butt hinges with necessary screws.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 TypeS, including cost of adhesive of approved quality. 1.0 mm thick

Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and fixing M.S. sliding door bolts bright finished or/and black enamelled,with nuts and screws etc.compelled:

each sb

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass hangging type floor door stoper with necessary screws etc. compelte.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding tower bolt (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with nuts screws etc. necessary screws etc. complete.

Providing and fixing anodised aluminium work for doors, windows, ventilators and partitions with extuded built up standard tubular and other sections of approved make conforming to IS: 733 and IS: 1285, anodised trasparent or dyed to required shade according to IS: 1868. (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust fre straight, mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/paneling, C,P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately.)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing 18 mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels.

Area of each slab over 0.2sqm but upto 0.5 sqm Granite of any colour and shade

Extra for providing edge moulding to 19 mm thick marble stone counters, Vanities etc. over item no. 8.2 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. Granite work

Extra for fixing marble / granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture) of approved make in all colours, shades except begundy, bottle green,black of any size as approved by Engineer-in-chage in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 (1 Cement:3 Coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300 x 300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20mm thick Cement Mortar 1:4 (1 Cement: 4 Coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

20 to 25mm thick

Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm

12mm cement plaster of mix:

20mm cement plaster of mix :

6mm cement plaster to ceiling of mix:

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

Providing and fixing circular cast iron box for ceiling fan clamp 140mminternal dia, 73 mm height,.5 mm thick rim bottom and top lids, 1.5mm thick M.S sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron box by means of 3.3mm dia. round headed screws, one pcl at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing pressed steel door confirming IS code 351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if requird angle threshold of mild steel angle of section 50x25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. all comlete.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm ( ± 0.2 mm) , corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer’s specification and direction of Engineer-in-charge.

Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x 20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer’s specification and direction of engineer-incharge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Demolishing 1:3:6 or richer mix cement concrete including disposal of material within 50 metre lead:

Demolishing brick work In cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead:

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Making 25 cm (10") dia bore up to 4 mtr depth below ground with hand auger of approved quality in ordinary soi! (vide classification of soil item A ) true to plumb and without eccentri city in any stage of operation and disposal of the excavated earth up to 50 mtr , Lead in eluding all lifts , all complete as per approved disign and direction of E/l Details of cost for 4 piles of 4 m= 16 mtrs depth )

63 CM (25) UNDER -REAM Making 63 cm (25) dia under ream at required with hand auger of approved quality in ordinary soil (vide classification of soil ifem - A) true to plumb and without eccentri city in my stage of opration and disposal of the excavated earth up to 50 mts lead in eluding all lifts , all complete as per approved design and direction of (E/l)

Stone chips [Koderma By Road1 1K +132P KM]

Bricks

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing C.P. brass toilet paper holder :

Providing and fixing wash basin with C.I. rackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, ncludingpainting of fittings and brackets, cutting and making good the walls wherever require :

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers. (In O.T.)

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the all wherever required :

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing G.I pipes complete with G.I fittings including trenching and refilling etc.

Metre

Metre

Metre

Metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15 mm nominal outer dia Pipes

20 mm nominal outer dia pipes

Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15mm nominal bore

25mm nominal bore

32mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 100A.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

per litre

Providing and fixing C.P. brass , bib cock of approved quality conforming to IS : 8931

Providing and fixing C.P. brass long body, bib cock of approved quality conforming to IS standard and weight not less than 690 grams.

Providing and fixing C.P brass angle valve for basin mixer and gyser point of approved quality conforming to IS : 8931

metre

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage)

150 mm dia RCC pipe

250 mm dia RCC pipe

450 mm dia. R.C.C. pipe

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge.

100 mm nominal size dia.

150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (RMS) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

metre

`Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate,suitable GI box and earthing the point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable etc. as required.

Point

Supplying and fixing suitable size GI box with modular plate and cover including providing and fixing 3 pin 5/6 Amp modular type socket on switch/separate board (in surface / recessed PVC conduit wiring system) and 5/6 Amp modular type switch Earthing the 3rd pin, painting etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover including providing and fixing 6 pin 20/16 Amp modular type socket on switch/separate board (in surface / recessed PVC conduit wiring system) and 20/16 Amp modular type switch ,connection, painting etc, painting etc. as required. For Power Plug.

Wiring for power plug with 2 x 4 Sq.Mm. FRLS PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 no 4 Sq.Mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor single core cable in surface/ recessed medium class PVC conduit as required

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Wiring for twin control light point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable in Surface/ recessed medium class PVC conduit, 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5 Sq.Mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/power plug with 4 x 4 Sq.Mm. FRLS PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 2 nos. 4 Sq.Mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying & fixing 4 way (4 +12) three pole and neutral, sheet steel MCB distribution board 415 volts on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, hinged front acrylic cover for the MCB knobs, detachable gland plate, interconnections, phosphatised and powder painted earthing etc. as required.(without MCB's)

Providing and fixing 6 way(4+18), TP & N prewired, sheet steel, MCB DB,415 volts, on surface/ recess double door complete with loose wire box, terminal blocks, duly prewired with suitable size PVC insulated copper wire up to terminal blocks, tinned cooper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc.as required. (But without MCB / RCCB Isolator) .

Providing and fixing 8 way(4+24), TP & N prewired, sheet steel, MCB DB,415 volts, on surface/ recess double door complete with loose wire box, terminal blocks, duly prewired with suitable size PVC insulated copper wire up to terminal blocks, tinned cooper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc.as required. (But without MCB / RCCB Isolator) .

6/32 A SPN MCB 'C' series

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface / recess, complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate bus bar, interconnections, powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator)

Supply and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required :(for all Elec & LV services)

Earthing with copper earth plate 600mmX600mmX3mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. as required.

Earthing with GI earth plate 600mmX600mmX6mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/cable as required

Providing and fixing 25mm x 5 mm G.I strip on surface or in recess for connections etc. as required.

Supplying and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connecion with copper thimble excavation and refilling etc. as required.

75 mm.X 75 mm.X 50 mm. deep ( 4"X4")

Telephone socket outlet

T.V. antenna socket outlet

Providing and fixing M.V. danger notice plate of 200mmx150mm made of mild steel, atleast 2mm thick and vitreous enamelled white on both sides and with inscription single red colour on FRLSont side as required.

Supplying and fixing call bell/buzzer suitable for single phase, 230 volts, complete as required.

supply and installations of regular/standard model AC cieling fan of 1200 mm sweep including wiring the down rods of standard length upto 30 cm with 1.5 sqmm FR PVC insulated copper conductor etc as required.

Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

supply and Installation of 300 mm 230 V AC exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required

Supply, fixing of following types lamp inthe existing electrical fitting/fixtures etc as required. 18 watt CFL lamp.

Supply, and fixing single wall mounted 20/22 watt LED type baten fitting complete with electronic driver and LED tube etc directly on wall/cieling including connections with 1.5 sqmm FR PVC insulated copper conductor and earthing the body etc as required.

Supply and installation of 40 mm, 23V AC 230/250 volts, 50 HZ Wall/Cabin fan including fixing the bracket, making connections testing commissioning etc as required

DESCRIPTION OF ITEMS

B. Wall

Providing and filling (Back filling) profile "B" pressed steel door frame back hallow portion with cement concrete mix of 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 10mm nominal size)

Providing and fixing, uPVC pipes 6 Kg/Cm2 (IS: 4985) including all fittings (plain or door) e.g. bends, junction, offsets, access pieces, jointing with rubber ring/solvent cement joints including required suports,cutting chase or holes in walls and floors and making good where required.

Providing & fixing in position uPVC P"or S" trap/elbow of self cleaning design of following sizes for the embedded areas. Making proper connection with drip-seal joints, cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors where required.

Providing and fixing multi-floor trap fitting with maximum 3 inlets 32,40 or 50 mm size fabricated from 100/150 mm dia upvc pipes and sockets,fixed to C.I. trap with lead caulked joint and set in cement concrete as per standard drawing complete.

Providing and fixing END CAP or cleanout plug( Ceiling or Floor) with suitable inset keys for opening, male threaded joint with socket fixed to pipe complete in all respects.

Supplying & Installation of suitable 2Hp submersible pump B.S or K.S.B or equivalent make with finolex cable 1x3x2.5 squmm(upto 75mtr) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as MCB of 0-25Amp (Havell or Indocopp or MDS make), Volt & Ampere meter (AE make), single phase preventer (Minilac or VSP -1 make) starter (L&T or BCH make) etc of approved make, 40mm HDPE Pipe (25 mtr) and all accessories complete as per requirement of site.

Fabrication, supply, installation, testing and commissioning of cubicle type wall mounted L.T. panel made out of 16mm thick CRCA sheet including connection, inter-connection along with 4 strip aluminium bus bar as per CP WD specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel mounting switchgears etc. as required.,

High Back Revolving Chair having Seat and Back made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. HIGH BACK SIZE: 47.5 cm (W) x 69.5 cm (H) SEAT SIZE: 47.0 cm (W) x 48.0 cm (D) POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: 360° revolving type, Upright position locking, Tilt tension adjustment & Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt) PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5nos. twin wheel castors. The pedestal is 66.0cm pitch-center dia. (76.0 cm with castors.) TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

Office Table of Size : 1365mm (W) x 680mm (D) x 735mm (H) with 18mm thk. Pre-Laminated Board (PLB). Under-Structure : Square shape MS Section duly powder coated. Modesty Panel - Metal Modesty Storage : Drawer Unit (2D+1F) made up of 18mm thick Prelaminated particle board with PVC edge banding on exposed edges.

S/F/F Chair (Make IKEA / HERMAN MILLER/ GODREJ / HAWORTH) Size : Depth (D) - 57.0 cm Width (W) - 58.0 cm Height (H) - 88.0 cm Seat Height (SH) - 45.0 cm SEAT/BACK ASSEMBLY : The seat and back are made from chemically treated and seasoned wood, caned and finished with synthetic paint (Colour: Black with matt finish). *BACK SIZE: 45.1CM(W) X 39.0CM(H). *SEAT SIZE: 45.1cm(W) x 42.4cm(D). CANE FOR SEAT/BACK: Cane is made from mix of LDPE + HDPE Mix Material. The caning used for seat/back has high tensile strength as per IS: 5378 Part II, 1990. Cane breaking strength = 3000 Kg/cm 2 (min.) % Elongation at break =25%. ARMREST TUBE : The armrest tube is made of M.S. E.R.W. tube dia. 2.54cm. (1”) x 16BG thick and welded to the understructure assy. ARMREST : The armrest is gas-assisted injection moulded from black Polypropylene. UNDERSTRUCTURE ASSEMBLY : The understructure assembly is a cantilever type frame made of dia. 2.54cm. (1”) x 14BG. thick M.S. E.R.W. tube and powder coated.

Table Size: 1199 x 590 x 735 mm having top made of 18 mm thick superior quality pre-laminated particle board of Grade II Type II conforming to IS:12823 of approved quality and shade. The edges of the table shall be banded with PVC strip 2 mm thick using hot melt glue under heat and pressure. The table top shall be supported by 1 mm thick M.S. ‘C’ frame stiffener of size 24.2 mm (W) x 38 mm (H). The table shall have 4 legs made of Electric Resistant Welded prime quality CRCA steel round tubular frame of Dia. 25.4 mm size and of 1.2 mm thickness. The base of legs of the tables shall be covered with plastic caps. The table shall have one no. drawer units i.e. right side drawer unit shall have three box drawers. And overall size of drawer 355 mm (W) x 560 mm (D) x 430 mm (H). The drawer unit shall be made of 0.8 mm thick CRCA sheet and drawer trays shall be made of 0.6 mm thick CRCA sheet. The drawers shall glide on frictionless slides of 1.2 mm thick CRCA sheet and shall have a multi purpose steel lock with handles built in place. The drawer units to have a mechanism to ensure only one drawer opens at a time. Both the drawers are fitted to ‘C’ frame by machine screws. Joints shall be interlocked and welded to render a flawless appearance. All steel parts shall be pretreated for seven stage anti-corrosion treatment followed by powder coating of thickness 50–55 microns.

Overall Sizes (L)2065 mm x (W)850 mm x (H) 850 mm Material Specifications 1 Leg Frame - Made from E.R.W Tube of section 30 x 30mm and thickness 1.6 mm 2 Intermediate Frame - Made from E.R.W Tube of section 30 x 30mm and thickness 1.6 mm 3 Leg Shoe - Made from NYLON 6 (To avoid wear and sound) 4 Lying surface - Made from CRCA Sheet of thickness 1.2mm 5 Rachet - Made from M.S of thickness 5mm (Provides the back rest tilt 0°, 15°, 30° adjustment positions. 6 Bowl Stand - Made from S.S. 304 of section Ø15.9 7 S.S. Bowl - Made from S.S. 304 (To collect the fluids during the procedure) 8 Head Rest - Made from CRCA Sheet of thickness 1.2mm 9 Calf Rest - Made from Leathrite (Leatherite wth PU Foam and MS backing Sheet) 10 Lithotomy Rod - Made from SS 304 (To provide variable height & swivel position as per desired position) Finish Specification 1 Powder Coating - Epoxy polyester powder coating 2 Colour - Ral white, plastic parts in Gray Performance Specification Maximum Patient load - 135Kg

Overall Sizes: (L)2268 mm X ( W)922 mm X (H) 610 mm Description: Sheet Bed should be a plain bed used in the recovery ward. Material Specifications: Under Structure has a Higher diameter tube which should provide a sturdy understructure. Lying surface area of CRCA Finish Specifications: Head Board/Leg Board should be made of frame MS ERW RoundTube of sections Ø19, Ø25.4& Ø31.75mm, of thickness1.6 mm Provision for mounting of IV Pole and Mosquito Net pole should be present Finish Specifications: Powder coating should be Bacteriostatic and thermosetting epoxy Polyester, formulated to fulfill the requirements for bacterial protection. All powder coated parts in RAL white Performance Specifications: Maximum patient load should be 135 kg

Thickness-Mattress: 3"+ SANDWITCH CONSTRUCTION: Round corners - YES Hitlon thickness ( MM): 60 Hitlon density (Gm/dcm3): 23 Coir(Both side) Thickness MM: 20 Density (Gm/dcm3): 70, DRC (%): 22 QUILTING - COMBINATION / LAYERS: Pilled Foam – Quilting (One Side) Thickness MM - 14 Pilled Foam Density Gm/dcm3 - 18 PU foam / EPE sheet side walling Thickness MM - 3 TOTAL MATTRESS THICKNESS-MM - 87 REXINE (GSM): 150 Note: * Finish product thickness should be measure from outer to outer surface. Tolerance +5 mm

Dimension: Top Size - 760 (L) x 360 (W) x 850 (H) mm Featured with Laminated board top extending over the width of the bed, Tubular Frame work with 50mm Dia. Non-rusting Castors, and Pre-treated and Powder Coated.

Overall Sizes in mm: 1500 (L) x 850 (W) x 1210 (H) Flat single section bed with grille frame on 4 sides. Suitable for children up to 12 years. Drop down grill frame on both sides for protection of the patient. Material Specifications: Under Structure has a Higher diameter tube which should provide a sturdy understructure. Lying surface area of CRCA Finish Specifications: Head Board/Leg Board should be made of frame MS ERW RoundTube of sections Ø19, Ø25.4& Ø31.75mm, of thickness1.6 mm Provision for mounting of IV Pole and Mosquito Net pole should be present Finish Specifications: Powder coating should be Bacteriostatic and thermosetting epoxy Polyester, formulated to fulfill the requirements for bacterial protection. All powder coated parts in RAL white

Bonded Foam Mattress of Thickness 3" Size: 1415 x 785 x 75 MM

Three fold screen is a portable screen on castors having three screens which can be folded to provide privacy in recovery ward. Overall Sizes (L)2637 mm X ( W)640 mm X (H) 1720 mm Material Specifications 1 Fix Frame - Made from E.R.W Tube of Section Ø25.4 having Thickness 1.2 mm (To provide hinging to movable frame) 2 Movable Frame - Made from E.R.W Tube of Section Ø19.05 having Thickness 1.2 mm (Flexible frame has plastic hinge. It can be adjusted in provided space) 3 Leg Frame - Made from E.R.W Tube of Section SQ. 30 having Thickness 1.6mm 4 Caster Wheel - Of Section Ø50 (For Ease of movement) 5 Bush For Holding Pipe - Made from Nylon 6 (Plastic bush) 6 Screen - Casement fabric for screen which is opaque for providing modesty. Finish Specifications 1 Powder coating - Epoxy polyester. 2 Color - Powder coated parts in RAL white, Plastic parts in Gray (Pantone cool gray 8C), Casement fabric in green (RAL 6026)

Providing and installation at site ,Drip Stand with 4 hooks,height adjustable up to 130 cm to 230 cm, made of SS Steel Verticle tubes,fitted to SS five prolonged base,mounted on 5 cm swival twin castors.

Description - 4 legged basin stand mounted on castors. Overall Sizes- Base circle dia 425 X (H) 850mm. Material Specification: Stand - SS 304 tube of section 12.7mm & 25.4 mm thickness 1.2mm, Bowl - SS 202 sheet, spin section, thickness 0.8mm. Castors - High endurance Plastic injection moulded castors, 50mm in dia. Finish Specification - SS (Buffed) glossy mirror finish. Performance Specification - Maximum safe working load 20 Kg.

Description - Oxygen Cylinder Trolly is mounted on castors. Size - L-410mm X W-375mm X H-1112mm. Material Specification : Main Frame - MS ERW Tube, Section 25.4mm Thickness 1.6mm for holding the cylinder. Locking Rod -MS Rod, section 10mm, keeps the cylinder in position during transit. Base Frame -MS ERW Tube, section 25.4 X 25.4, thickness - 1.6mm, sturdy base for resting the cylinder. Castor Wheel -PU wheel, section 100mm, thickness 25mm, for ease of movement. Leg Cap -LDPE, to cap the open ends at the bottom. Finish Specification-RAL White, epoxy polyster powder coating, plastic parts in pantone cool grey 8c. Performance Specification -Maximum safe working load 50 Kg.

Material Specification - Top Shelf - SS 304 Sheet, thickness 1mm, Supporting Legs -SS 304 tube, section 31.8mm pipe, thickness 1.2mm, Horizontal Bar - SS 304 Tube, section 12.7mm, thickness 1.2mm, welded with the legs. Bottom shelf - SS 304 Sheet, thickness 1mm. Castors - High endurance, Plastic injection moulded castors, section 125mm. Finish Specification - SS buffed to Glossy mirror finish. Performance Specification - Maximum safe working load 20 Kg.

Description - Stretcher on trolley is a removable stretcher mounted on a sturdy trolley having castors for ease of movement.Overall Size - (L)2005 mm x (W) 620 mm x (H)790 mm. Material Specification - Trolly - ERW Tube, Section 31.75 & 25.4mm, Thickness - 1.6mm, Provides the base to rest the stretcher on its four resting pads. Holder for Stretcher - MS with rubber pad, Used to hold the stretcher in position on to the trolly. Castor Wheel - 200mm dia Wheel with diagonal lockable castor. Stretcher - ERW Tube, Section 25.4mm, Thickness 1.6mm, Removable from Trolly to provide flexibility of reach. Stretcher Top Sheet - CRCA Sheet, Thickness - 1.2mm, Contoured stretcher top provides safety to patient during handling. Powder Coating - Epoxy Polyster. Colour - MS Part in RAL White Powder Coating, Plastic parts in Pantone cool grey 8C. Performance Specification - Maximum Patient Load 135 Kg.

Seat and back easily removable and replaceable. Fine and durable upholstery for seat and back. Nylone Handgrips and Padded arm rest. Polished SS constrct. Solid tire wheels with Rear wheel lock. Aluminium leg rest-swing away type. All the stainless steel should be seamless conforming to 304 grade/16 gauge and polished finished.

3 Seater Chair with following specification: Seat Shell - Seat shell is welded assembly of seat, Back & side frame. Seat & back are made of 0.12±0.013cm thk CR steel sheet with oblong perforations. They are welded to side frame of size 3.2±0.05cm X 0.5±0.05cm thk HR steel. Welded assembly is powder coated (DFT 40-60 microns). Seat has a front warefall edge for comfortable seating and also has a buttock support curve. Understructure Assembly - Consists of connecting beam & leg assembly made of MS ERW oblong tube size 7.5±0.03cm X 5.0±0.03cm X 0.02±0.016cm thk and is powder coated (DFT 40-60 microns). Leg assembly is fitted with shoes and levellers in Nylon. Leg assembly is designed with minimal area of contact close to ground providing easy access for cleaning purposes. Connecting beam is fitted with snap locking end capfor side by side understructure alignment. Arm Rest Assembly - Consists of arNSIest frame & arNSIest pad.ArNSIest frame is made up of size 3.175±0.05cm X 0.47±0.027 cm thk HR steel and is powder coated (DFT 40-60 microns). ArNSIest pad is injection moulded in nylon and is fitted onto the arNSIest frame.

Size - 1980mm (H) X 916mm (W) X 486mm (D), Construction & Material - Welded Construction, 0.7mm thick (±0.07mm) CRCA (D Grade as per IS:513) for shelf, 0.8mm thick (±0.08mm) High yield strength (D Grade High yield Strength as per IS:513) CRCA for Doors & Back, 0.9mm thick (±0.08mm) CRCA (D Grade as per IS:513) for all other components. Locking & Handle - Mazak Handle, Three way locking mechanism with shooting bolt. Shelving - Height wise adjustable shelf mounting, Uniformly distributed load capacity per each full shelf is 40 Kg maximum, 4 Nos. adjustable full shelf, Leveler - M10 Screw type leveler with hex plastic base.Finish - Epoxy powder coated to the thickness of 50 microns ( ±10)

Load bearing members of the system should be made out of High strength HR steel having properties equivalent to grades specified by IS 5986:2002 / IS 2062:2006 In addition to high strength, the raw material used for structural load bearing members also should possesses adequate ductility to ensure toughness. The material should also have the necessary impact strength for cold room applications upto -30° C Surface finish: All components must have thorough anti-rust treatment to prevent corrosion, thereby increasing the life of the component. Steel components must be powder coated for obtaining a smooth, scratch resistant and a lasting attractive, finish. The Dry Film Thickness (DFT) of 35 microns is required on an average after Powder coating. All components are to be an elaborate 4 step, six zone anti corrosion treatment, viz. De-greasing as per IS 6005:1970, Rinsing, Phospating as per IS 3618:1966 and De-mineralized water rinsing. Angle: Vertical load carrying member that transfers load to the ground via base plates, its Material Specifications should be as per IS: 5986 (ST 42). Angles should be of rolled formed construction to ensure minimal residual stresses and accuracy throughout the length of the angles, and should take the designated load. Slots at every 19.05 mm for height optimisation or adapt to ever changing SKU sizes and Grouted through base plates. Surface Finish: Epoxy-Polyester Powder Coated – Lead Free BS Grey/Oxford Blue in colour. Panel: Should conform to IS:513 D, and minimum yield strength 210 MPa. No. of bends : 6 Manufacturing : Press forming. Panels are to be provided with lipped flanges. Width of the flange being 31 mm and depth of lip 17 mm. Panels are provided with 9 mm holes on the flange for corner plates, cladding sheets. Design Criteria : Deflection to be under SEMA guidelines. Surface Finish : Epoxy-Polyester Powder Coated – Lead Free BS Grey/Oxford Blue in Colour. SIZE: Width : 3 ft Depth: 18” Height: 6’ Load Capacity : 90 kg / loading level UDL (Uniformly Distributed Load)

Providing and installation at site of Revolving Stool with stainless steel top, with pneumatic height adjustment and moulded five pronged mobile base with 5cms swivel twin castors as required.. • Height Adjustable: 48 to 60 cms.

Overall size 402 mm(L)x404 mm(W)x835 mm(H)-Locker with one cabinet with stainless steel,rest structureis in MS powder coated ,cabinet provided with cam lock.It has ERQ sq tube structure of 25.4 mm Sq section of 1.6 mm thickness.Shoe is made up of PVC+nitrrile and top is SS 304 sheet with 0.8 mm thcikness and cabinet of CRCA of 1 mm thcikness.Handles are ABS.Powder coated epoxy olyster,rubber and plastics parts in grey,SS top buffered mirror finish.The manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products

Description The examination table made of sturdy structure. The backrest has a ratchet mechanism for tilting the backrest. Overall Sizes L - 1830 mm x W. - 600 mm x H. - 850 mm Material Specifications 1. LegFrame - MSE.R.WTube 30x30 Thickness 1.6mm 2. Intermediate Frame - MS E.R.W Tube 30 x 30 Thickness 1.6mm 3. Leg Shoe Nylon 6 (To avoid wear and tear) 4. Lying surface - MSS. Sheet Thickness 1.2mm 5. Ratchet - M.S plate Thickness 5mm (Provides the bask rest tilt 0°, 15°, 30° adjustment positions. Finish Specifications: 1. Powder coating Epoxy polyester. 2. Color RAL white, Plastic parts in Gray (Pantone cool gray 8C) Performance Specifications Maximum safe patient Load - 135 Kg.

Thickness-Mattress: 3"+ SANDWITCH CONSTRUCTION: Round corners - YES Hitlon thickness ( MM): 60 Hitlon density (Gm/dcm3): 23 Coir(Both side) Thickness MM: 20 Density (Gm/dcm3): 70, DRC (%): 22 QUILTING - COMBINATION / LAYERS: Pilled Foam – Quilting (One Side) Thickness MM - 14 Pilled Foam Density Gm/dcm3 - 18 PU foam / EPE sheet side walling Thickness MM - 3 TOTAL MATTRESS THICKNESS-MM - 87 REXINE (GSM): 150 Note: * Finish product thickness should be measure from outer to outer surface. Tolerance +5 mm

Medicine Trolley Overall Sizes L - 532 mm x W. - 902 mm x H. - 915 mm Material Specifications Mild Steel Epoxy Powder Coated Framework Stainless Steel Shelves Two Drawers under the each shelf On costars.

Providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. Duly anodised all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints of appropriate size all complete as per diirection of Engineer in Charge.

Wall Mounted, 450x100mm

Door Mounted, 300x80mm

Illuminating Direction retroreflective 450mm Dia signage with MS suppurt

6 KG ABC Fire Extinguisher

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70mm and bottom dia A/F 130mm, made of 3mm thick sheet along with base plate of size 220X220X12mm, small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Supplying and fixing 40/45 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying & drawing 3x2.5sq.mm size FR PVC insulated copper conductor single core cable in the existing pipe as rqd.

Period of Bid Validity

Cost of Bid Document (in Rs)

Group A Tendered Rate comparison to B.O.Q.Amount in percentage (in Figure)

Group B (Item rate) total amount in Figure

As Per Agreement

Boundary Wall