LOT1

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after . as per directions and approval of Engineer-in-charge . including all cost of material, labour and T&P etc. after cost deduction of old material

Dismantaling of ACP sheet & Cutting of damaged M.S hollow pipes by a grinder and preparation of surface including cost of all material ,labour ,tool and t&p etc. after cost deduction of old material.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc.

Supply & fixing of 16 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 360 mm base plate 32 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect.

Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 Watt. Confirming to IP 66 protection complete in all respect.

Supply, Installation, Testing and Commissioning of LED RGB/ RGBW Linear Wall Washer luminaire for Facade lighting with aluminium extruded housing, of following wattage. Luminaire shall be capable of producing dynamic color changing light with 16 million colors by DMX/ Ethernet based control. The beam angle of the fitting shall be narrow, medium, wide or a symmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100 to 270 VAC, 50Hz, power factor> 0.9. Fixture shall be suitable to operate at ambient temperature range of -10°C to +50° C and shall be IP 65 and IK 06 rated. Life time should be at least L 70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, waterproof connectors etc. as required. 130 Watt

Supplying and laying of aluminum conductor PVC insulated armored sheathed cable 1100 volts grout with M.S. clamps of suitable size as directed by Engineer-in-charge, complete in all respect. Armoring shall be properly connected by clamps (Four underground laying cable shall be placed at a depth of 750 mm below ground level over a cushion of 75 m thick and all around and protected with bricks on sides and top). S.No. Name of Work Unit Labour Comp 10 sq. mm 5/4 Core Cable

Supplying and drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing Surface/recessed steel/PVC conduit as required. 3 X 2.5 sq. mm

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes