Up gradation of Echo room at SNM Hospital Leh ( Under Capex)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Demolishingcementconcretemanually/bymechanicalmeansincludingdisposalof material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dry stone pitching (any thickness) excluding cost of stones. On Horizontal

Providing & fixing Factory manufactured counter cabinets (Overall depth=375mm-400mm, Overall height=upto2300mm) with All vertical and horizontal surfaces of box made in 18mm thk prelaminated particle board, All visible edges of covered with hot pressed and glued 2mm thk pvc edge binding tape of matching colour, Shutters made of 18mm thk prelaminated particle board, laminated with 1mm thk high gloss/textured laminate on front face and 1mm thk laminate matching with box on inside, All visible edges of shutter covered with hot pressed and glued 2mm thk pvc edge binding tape of matching. The shutters shall be fixed to frame with appropriate auto closing hinges of approved make and shall have 300mm high stainless steel handles. (Only front face of cabinets shall be measured for payment purpose)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Removingdryoroilbounddistemper,waterproofingcementpaintandthelike by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wallpaintingwithplasticemulsionpaintofapprovedbrandandmanufactureto give an even shade One or more coats on old work

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coat

ProvidingandfixingISImarkedflushdoorshuttersconformingtoIS:2202(PartI) non-decorativetype, coreof blockboardconstructionwithframeof 1st class hardwoodandwellmatchedcommercial3plyveneeringwithverticalgrainsor cross bands and face veneers on both faces of shutters: 35mmthick including ISImarkedStainless Steel butt hingeswithnecessary screws

Paintingwith syntheticenamel paint of approvedbrandandmanufactureof required colour to give an even shade : One or more coats on old work

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

ProvidingandlayingrectifiedGlazedCeramicfloor tilesofsize300x300mmor more(thicknesstobespecifiedbythemanufacturer),of1stqualityconformingto IS :15622,ofapprovedmake,inall colours, shades,exceptWhite, Ivory,Grey, FumeRedBrown, laidon20mmthickCementMortar1:4(1Cement :4Coarse sand),[email protected]/sqmincludingpointingthejoints with white cement and matching pigments etc., complete.

DismantlingG.I.pipes(externalwork) includingexcavationandrefillingtrenches aftertakingoutthepipes,manually/bymechanicalmeansincludingstacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore

Supplying and fixing of following electrical items suitable for Exhaust Fan 225 mm PVC shutter type.

Steelwork inbuiltuptubular (round, squareor rectangularhollowtubesetc.) trusses etc., including Hot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mmofall T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

FinishingwithEpoxypaint (twoormorecoats) at all locations preparedand applied as permanufacturer'sspecifications includingappropriate primingcoat, preparation of surface, etc. complete. On steel work

10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar with bhusha @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 2 cow-dung) and covered with machine moulded tile bricks, grouted with cement mortar 1:3 ( 1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat.%0 mm thick cement concrate M10 with Fibre Mash Complete Job.

Providing and fixing of material for the insulation of water storage tank of with nitrile sheet taping with cello tape, rockwool 6 inch per side, wire mesh, polythene, alluminium sheet 26 gage cladding with dia of, complete job 19mm thick nitrile sheet.

Providingandplacingonterrace(atall floor levels)polyethylenewaterstorage tank ISI :12701markedwithcoverandsuitablelockingarrangementandmaking necessary holesfor inlet,outletandoverflowpipesbutwithout fittingsandthe base support for tank

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire