Signage, Equipment, Solar and other Misc works for permanent campus of NID AP.

S. NO. DESCRIPTION NS AMOUNT TOTAL AMOUNT

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including

attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor five

level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal

Centering and shuttering including strutting, propping etc. and removal of

2.1 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 35 453.35 15867.25

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer using structural steel etc. as required.

3.1 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Kg 2000 90.1 180200.00

4 NS BORE PACKING ( ALL CI AND UPVC PIPES)

Preparing the inside surface of core and PVC by roughening using suitable file to get better

adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to

remove any laitance or loose flaky particles. Providing necessary formwork for packing the bore

using suitable arrangement (depending upon site conditions). Applying a coat of styrene-

butadiene based polymer coating using Nitobond SBR to enhance adhesion between the packing

material and other surfaces. Packing the gap using non-shrink cement polymer based grout using

conbextra GP2 upto the surface of the bore whilst the Nitobond SBR is in tacky state. The above

analysis is based on assumption for 150mm diameter core with 110mm diameter PVC for 5” thick

slab only. Typical Properties Compressive strength at 28day as per BS 1881 45N/mm2,

completely as per the manufacturer’s Instruction.

5 NS COVING TREATMENT AT JUNCTION OF RCC SLAB AND PARAPET WALL Mtr 365 177.28 64707.2

Coving treatment including Providing gola 50x50 mm in cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 stone aggregate 10 mm and down gauge),

Making coving of 50mm X 50mm at all the flat & vertical junction using 10 mm thick Fosroc

Renderoc S Single component, shrinkage compensated, fiber reinforced, thixotropic

cementitious mortar, to achieves a minimum compressive strength of 20 MPa in 1day and 55

MPa in 28days when tested as per EN 12190 and capable of applying 50mm thickness in single

layer of approved product finished flush with existing surface.

6 Waterproofing of roof slab

Signature of Contractor With Seal Page 1 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Supply and application of single-component, Pitch free seamless roller/spray applied Nitoproof 600PF

applied at average minimum DFT of 1.5 mm using a Graco King type pump with 60:1 ratio at pressure

5.5 bar (80 psi), hose diameter 13mm with a 10mm wip end. Tip size: 0.58mm - 0.84 (23-33 thou). It

shall possess the following properties: Solids by Volume : 85%, Tensile Strength ASTM D412 : >1.9

MPa, Tear resistance ASTM D624C : 15(N/mm), Elongation ASTM D-412 : >400%,Adhesion in-peel test

ASTM C836 (N) : > 50N

Providing a non-woven Geotextile fabric of 200GSM over the cured waterproofing membrane

6.2 NS before going for a protective layer.

Providing and laying min 50/75mm (as per the design thickness to provide proper slope at 1:100

or 150) thick polymer modified screed concrete of M20 grade and admixed with Integral

6.3 NS waterproofing compound confirming to IS 2645 of Fosroc Conplast WL at a dosage of 125 ml Sqm 1968 422.71 831893.28

/50Kg bag of cement. Subsequently, providing grove Cutting (size 5mm wide and 10mm deep)

mechanically in a panel size of 3m x 4m which shall be filled with two-component Polysulphide

flexible sealant of Fosroc Thioflex 600 with MAF of 25%, Tensile modulus of XX.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM

rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and

jointed mechanically wherever required including cleat angle, Aluminium snap beading for

glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings

and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for

7.1 21.1.1 For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to IS:

1868, Minimum anodic coating of grade AC 15)

B HORTICULTURE WORKS

8 23.2 Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth Cum 1650 308.35 508777.50

measured in stacks will be reduced by 20% for payment).

Signature of Contractor With Seal Page 2 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing

ground prepared with proper level and ramming with required tools wooden and than rolling the

9.1 2.34 surface with light roller make the surface smoothen and light watering the same and Per Sqm 24000 87.5 2100000.00

maintenance for 30 days or more till the grass establish properly, as per direction

of the officer in charge

Providing and fixing Neelgiri/Mexican grass turf with earthy 50mm to 60mm thickness of existing

ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than

9.2 2.33 rolling the surface with light roller make the surface smoothen and light, watering with sprinkler Per Sqm 6000 214.4 1286400.00

and maintenance for 30 days or more till the grass establish properly as per direction of officer

Supply & Planting best quality trees inclusive of cultivation of trees bead to required depth. All

trees / plants to be approved before planting including the cost of making hole, slude or

manure,Mixing earth and sludge or manure in the required proportion (Cost of good earth paid

10 NS shall be paid exta) and watering .

10.1 NS African Tulip Tree (Height of 150 -165 cm) Each 1 850 850

10.2 NS Gulmohar Tree (Height of 150 -165 cm) Each 7 850 5950

10.3 NS Orchid Tree (Height of 120 -150 cm) Each 2 850 1700

10.4 NS Copper Pod (Height of 150 -165 cm) Each 6 850 5100

10.5 NS Pink Trumphet (Height of 150 -165 cm) Each 23 850 19550

10.6 NS Golden Bell (Height of 150 -165 cm) Each 7 850 5950

10.7 NS Crepe Mrytle (Height of 150 -165 cm) Each 4 850 3400

10.8 NS Indian Rosewood (Height of 120 -135 cm) Each 8 850 6800

10.9 NS Peepal, Sacred Fig (Height of 150 -165 cm) Each 5 850 4250

10.10 NS Indian Cork Tree (Height of 150 -165 cm) Each 2 850 1700

10.11 NS Kadam Tree (Height of 150 -165 cm) Each 15 850 12750

10.12 NS Golden Shower, Amaltas (Height of 120 -135 cm) Each 13 850 11050

10.13 NS Button Wood (Height of 150 -165 cm) Each 2 850 1700

10.14 NS Banyan Tree (Height of 120 -135 cm) Each 1 850 850

10.15 NS Sampangi (Height of 90 -105 cm) Each 6 850 5100

10.16 NS Papaya Tree (Height of 120 -150 cm) Each 1 850 850

10.17 NS Terminala Mentalis (Green & White) (Height of 150 -165 cm) Each 20 850 17000

10.18 NS Frangipani White, Pink Red & Yellow (Height of 150 -165 cm) Each 9 1350 12150

10.19 NS Fern Leaf Tree (Height of 150 -165 cm) Each 9 1350 12150

10.20 NS Taruma Tree (Height of 150 -165 cm) Each 10 1350 13500

10.21 NS Jacaranda (Height of 150 -165 cm) Each 4 1350 5400

Signature of Contractor With Seal Page 3 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

10.22 NS Neem (Height of 120 -130 cm) Each 18 1350 24300

10.23 NS Jamun (Height of 150 -165 cm) Each 3 1350 4050

10.24 NS Mango (Badam & Rasalu) (Height of 60 -75 cm) Each 16 1350 21600

10.25 NS Jackfruit (Height of 150 -165 cm) Each 1 1350 1350

10.26 NS Chikkoo (Height of 150 -165 cm) Each 1 1350 1350

10.21 NS Guava (Height of 150 -165 cm) Each 4 1350 5400

10.28 NS Banana (Height of 150 -165 cm) Each 2 1350 2700

10.29 NS Star Fruit (Height of 150 -165 cm) Each 2 1350 2700

10.30 NS Love Apple (Height of 150 -165 cm) Each 3 1350 4050

10.31 NS Tamarind (Height of 120 -150 cm) Each 12 850 10200

10.32 NS Casia Siana/ Kassod Tree (Height of 150 -165 cm) Each 11 850 9350

10.33 NS Pongamia Gabra (Height of 120 -135 cm) Each 10 850 8500

10.34 NS Bamboo (Height of 150 -165 cm) Each 42 850 35700

10.35 NS Rain Tree (Height of 150 -165 cm) Each 8 850 6800

10.36 NS Curry Tree (Height of 150 -165 cm) Each 3 850 2550

10.37 NS Cannon Ball Tree (Height of 150 -165 cm) Each 4 850 3400

10.38 NS Lemon Tree (Height of 150 -165 cm) Each 7 1350 9450

10.39 NS Amla Tree (Height of 150 -165 cm) Each 2 1350 2700

10.40 NS Golden Cane Palm (Height of 120 -150 cm) Each 91 1350 122850

10.41 NS PLUMBEGO (Height of 30 -45 cm) Each 50 90 4500

10.42 NS CHANDANI (Height of 45 -60 cm) Each 23 90 2070

C Electrical Works

Supply,Instllation, Testing and commissioning of 1600A Aluminium Air Insulated Busduct for

Outdoor installation -3 Phase 4 Pole (R, Y, B, N) and external Earth strips, 50 c/s, 1000 volts , 50

kA for 1 sec including following accessories as mentioned below as per technical Specification

11 NS complete as required.

(Note:-Bidder to coordinate with the main electrical contractor to prepare the detail GA drawing

as per actual site layout for Client/Consultant approval. Qtys taken are for estimation purpose

11.1 NS Straight run of bus duct Indoor + Outdoor with canopy Metre 30 43150.16 1294504.8

11.2 NS Adaptor Box at Panel end Set 2 16558.63 33117.26

11.3 NS Adaptor Box at Transformer end Set 2 16558.63 33117.26

11.4 NS Copper Flexible at Transformer end Set 2 52325.28 104650.56

Signature of Contractor With Seal Page 4 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

11.5 NS Copper Flexible at Panel end Set 2 52325.28 104650.56

11.6 NS Wall Frame Assembly with Fire Barriers Set 2 31130.23 62260.46

11.7 NS Space heater + Thermostat + MCB Set 2 7285.8 14571.6

11.11 NS Silica gel breather Nos 2 5961.11 11922.22

11.9 NS Phase Crossover Set 4 25831.47 103325.88

11.12 NS Bi-metallic expansion joints Set 4 11259.87 45039.48

11.13 NS Hot dip Galvanised Bus duct Support Structure. Kg 1250 132.47 165587.5

Subtotal © - 2056203.08

D Solar Photovolatic Power Plant

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant

conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar

cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure

of suitable strength with following components complete as required:-

a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to

IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module

conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/

systems must be warranted for their output peak watt capacity, which should not be less than

90% at the end of 10 years and 80% at the end of 25 years.

b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three

phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not

less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from

0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage

c) Data Monitoring System complete with accessories.

d) Fixing of Array junction box & Main junction box with IP 65 protection and termination

arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc.

e) Lightning and surge voltage protection.

f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper

conductor 1.1 kV grade armoured power and control cables between solar modules, main power

cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and

other accessories etc. as required

Subtotal (D) - 5066900.00

E GYM EQUIPMENT

Signature of Contractor With Seal Page 5 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Providing and fixing of following gym equipment complete in all respect as required as per

13 specification.

13.1 Cardiovascular Equipments:

13.1.1 NS DISPLAY - 7" or more LCD / MOTOR - 4HP / SPEED - 0.5 ~14KM / INCLINE - 10% / Nos. 1 1,23,488 - 123488.12

MOTOR CONTROL - AC INVERTER / / USER WEIGHT - 150 KGS.

Elliptical Cross Trainer :

LED dot matrix console readouts: incline, time, distance, calories, pulse, speed / rpm,

level, watt, fan etc.,atleast 14 motivating programs or more for different workout

requirements,Level Control : 15 resistance levels,12 kgs flywheel, Both forward & reverse

motions offer various workout options, ,Maximum user weight : 150 kg. 165 x 84 x 62.5

13.2 Strength Equipments:

203 cm (L) x 152 cm (B) x 147 cm (H) or more

All frames structures electro statically powder coated to ensure maximum corrosion and

chip resistance. High density foam upholstery.

Olympic Flat Bench :

141cm (L) x 68cm (W) x 42cm (H) or more.

All frames structures electro statically powder coated to ensure maximum corrosion and

chip resistance. High density foam upholstery.

Multi Bench Adjustable :

138 cm (L) x 65 cm (B) x 69 cm (H) or more

All frames structures electro statically powder coated to ensure maximum corrosion and

chip resistance. High density foam upholstery.

Solid Dumbbells (in kg)

Made from high grade virgin rubber ( Cast Iron Inside) for long life,Tear proof, soundless

& bouncy effect.Required Sizes (in Kgs) 2.5, 5, 7.5, 10, 12.5, 15, 17.5, 20, 25 1 Pair

Dumbbell Rack :

2 tier dumbbell rack. Suitable for 9 pairs or more number of dumbells

Solid Olympic Plates (in kg) :

13.2.10 NS Made from high grade virgin rubber ( Cast Iron Inside) for long life,Tear proof, soundless kg 65 291 - 18943.08

& bouncy effect. Required Sizes (in Kgs) 2.5, 5, 10, 15 Each 1 Pair

Subtotal (E) - 5,18,989

F Kitchen Equipment

Signature of Contractor With Seal Page 6 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

14 NS WET GRINDER - 7 Liter Capacity

SS WET MASALA GRINDER - Floor Model Wet Masala Grinder, Structures complete S. S. ,

Motor 2 HP of Crompton make oe equivalent 220 V, AC with Coconut scraper and Heavy Duty Nos. 1 23844.43 - 23844.43

Grinding Stone.

SS GARBAGE BIN 60 LITER CAPACITY

SIZE : 15" DIA X 29" HEIGHT

SS 2 BURNER COOKING RANGE

COMPLETE 304 GRADE

Top ss sheet 16 swg 304 grade, side skriting ss sheet 20 swg 304 grade, ms angle frame

16 NS support, square grid, burner, copper pipe, nc valve, 38 mm dia ss vertical pipe legs 16 swg 304 Nos. 1 29143.2 - 29143.2

grade, adjustable white nylon bullets.

SIZE : 48"X24"X34"

17 NS POTATO PEELER 20 KG CAPACITY heavy duty gear assembly with 1 Hp motor Nos. 1 47026.52 - 47026.52

SS WORK TABLE WITH 2 UNDER SHELVE

COMPLETE 304 GRADE

Top ss sheet 16 swg 304 grade, Middle & bottom shelve ss sheet 20 swg 304 grade, ms angle

frame support, 38 mm dia ss vertical pipe legs 16 swg 304 grade, adjustable white nylon bullets.

SIZE : 60"X24"X33"

SS WORK TABLE WITH 2 UNDER SHELVE

COMPLETE 304 GRADE

Top ss sheet 16 swg 304 grade, Middle & bottom shelve ss sheet 20 swg 304 grade, ms angle

frame support, 38 mm dia ss vertical pipe legs 16 swg 304 grades, adjustable white nylon bullets.

SIZE : 30"X30"X33"

SS 4 DOOR VERTICAL FRIDGE

COMPLETE 304 GRADE

inner body ss sheet 304 grade, outer body ss sheet 20 swg 304 grade, kirlosker compressor /

20 NS emersion brand, imported copper pipes, 100% puff insulation, digital temperature reading, 38 mm Nos. 1 145715.98 - 145715.98

dia ss pipe legs 16 swg 304 grade, adjustable white nylon bullets.

SIZE : 48"X30"X80"

Signature of Contractor With Seal Page 7 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

SS CHAPATHI BHATTI WITH PUFFER

COMPLETE 304 GRADE

Top ms plate 16 mm thick, puffers plate, side skriting ss sheet 20 swg 304 grade, ms angle

21 NS frame support, rv burner, copper pipe, nc valve, 38 mm dia ss vertical pipe legs 16 swg 304 Nos. 2 55637.01 - 111274.02

grade, 25 mm dia ss supporting pipe 16 swg 304 grade, adjustable white nylon bullets.

SIZE : 72"X30"X34"

DOUGH KNEADER MACHINE 30 KG CAPACITY

Heavy duty special grated motor having cyclo gears,, SS kneading arms and SS bowl, with break

provision etc. Direct coupled drive 2HP motor.

WET PLATE HOLDING RACK 5 SHELVE

COMPLETE 304 GRADE

All shelve ss sheet 18 swg 304 grade, 38 mm dia ss vertical pipe legs 16 swg 304 grade,

adjustable white nylon bullets.

SIZE : 36"X18"X72"

SS BAIN MARIE WITH 5 GN PAN & FRONT PIPE RAILING

1/1X150 MM DEEP GN PAN - 5 NOS

COMPLETE 304 GRADE

Top ss sheet 16 swg 304 grade, side skriting ss sheet 20 swg 304 grade, Bottom shelve ss sheet

20 swg 304 grade, electric heater, indicator lamp, rotary switch, thermostats, 38 mm dia ss

vertical pipe legs 16 swg 304 grade, adjustable white nylon bullets.

MICRO OVEN 20 LITER CAPACITY

26 NS WEIGHING MACHINE 300 KG CAPACITY Nos. 2 11922.22 - 23844.44

weighing M/c with auto calibration facility , high precision load cell , auto zero tracking -

SS PLATFORM TROLLEY

COMPLETE 304 GRADE

Platform made with ss sheet 18 swg 304 grade, 38 mm dia ss pipe handle, ss supporting pipe,s

5" dia heavy duty wheels.

SIZE : 36"X24"X39"

Signature of Contractor With Seal Page 8 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

SS CROCKERY RACK 5 SHELVE

COMPLETE 304 GRADE

All shelve ss sheet 18 swg 304 grade, 38 mm dia ss vertical pipe legs 16 swg 304 grade,

adjustable white nylon bullets.

SIZE : 36"X18"X72"

29 NS Sandwich Griller - Double Plate (580x410x190) Nos. 2 12981.97 - 25963.94

COUNTER TOP SANDWICH GRILLER - Unit made of complete SS Sheet with Two Nos. Cast

Iron made Grilled Plate [ Top & Bottom ] with Individual Electrical Heating Element with

Thermoset for Temperature Controller and . Indicating Lamp. Each Top Plate have Pull & Press -

SS Spring loaded Handel for proper Grilling. Total Elec. Load: 3.6 KW, 220V, AC. individually

with Auto Power Cut Off.

JUICE MAKER 900 WATT

31 NS PULVERISER 1.5 HP MOTOR Nos. 2 18545.67 - 37091.34

32 NS VEGETABLE CUTTING MACHINE WITH 5 SAPERATE BLADES Nos. 2 32454.92 - 64909.84

SS SINGLE BURNER BULK COOKING RANGE

COMPLETE 304 GRADE

Top ss sheet 16 swg 304 grade, side skriting ss sheet 20 swg 304 grade, ms angle frame

33 NS support, burner, copper pipe, nc valve, 38 mm dia ss vertical pipe legs 16 swg 304 grade, Nos. 4 19208.02 - 76832.08

adjustable white nylon bullets.

SIZE : 30"X30"X20"

MIXI 1600 WATT WITH 2 JAR

MIXI 1200 WATT WITH 2 JAR

SS DISH LANDING TABLE

COMPLETE 304 GRADE

Top ss sheet 16 swg 304 grade, ms angle frame support, 38 mm dia ss vertical pipe legs 16 swg

304 grade, 25 mm dia ss supporting pipe 16 swg 304 grade, adjustable white nylon bullets.

SIZE : 60"X24"X34"

Signature of Contractor With Seal Page 9 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

SS UNDER COUNTER FRIDGE

Top ss sheet 16 swg 304 grade, inner body ss sheet 304 grade, outer body ss sheet 20 swg 304

grade, kirlosker compressor / emersion brand, imported copper pipes, 100% puff insulation,

37 NS digital temperature reading, 38 mm dia ss pipe legs 16 swg 304 grade, adjustable white nylon Nos. 1 95377.73 - 95377.73

CHEST FREEZER 550 LITER CAPACITY

BRAND : ROCKWELL

Supply and installation of DISH / GLASS WASHER - Completely made of SS 304 Gr. 20 swg

Sheet with CNC finishing. Unit have one Water tank OF 30 Ltrs capacity, Rolling Water Capacity

6 Ltrs, Programing time 102 Second, Power : 5.5 KW, 220V, AC with Hot Water generation and

spray in high speed System. All washing process have maintain by PCB with timer. Unit have

provision for Dosing pump separately ( Size 595 x 655 x 830).Basket size: 500 x 500, Capacity:

35 Buskets / Hr as per direction of EIC.

Supply and installation of Water Cooler of approved make of storage capacity of 40 Litre and

nominal cooling Capacity of 20 Litre/ Hr made of SS 304 as per direction of EIC.

Supply and installation of DHOSA HOT PLATE- Dosa Hot plate thickness will be 16mm. SS

Sheet Fabricated with MS underneath structure Perforated three-side panel made of 20 swg S.

41 NS S. , Non-perforated front panel and legs made out of 38 mm Sq. S. S. Pipe with four-side cross Nos 2 18545.67 37091.34

bracing with 25 mm Sq, S.S. , Pipe and hard nylon adjustable bullets. All Burners including Pilot

and Gas Control valves will be HPC make.(Size 975 x 650 x 850)

Subtotal (F) - 1949840.88

Signature of Contractor With Seal Page 10 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Supplying and fixing of Pylon Display sign. Providing MS box frame pylon structure of 38mm x

38mm MS square pipe with fabricating, grinding, zinc premier emulsion painting. Providing

approved colour ACP sheet of 4mm thick thickness with alloy grade 3105 H 14 PVDF coating for

anti fungal properties. Providing fabricating to the MS box for the ACP cladding with sub

structure fastening materials and hardware items complete in line and level, heights and depths

with 789 silicon sealant. Providing opaque acrylic 3D letters of approved colours for displaying

the Pylon artwork content with 6mm thick and 0.40 transparency high tech plastic material

particularly high transparency and impact resistance levels. Providing computerized laser cutting

to the existing artwork design on the opaque acrylic sheet along with pasting on ACP sheet

backdrop. Providing HP Jet eco solvent print of existing ornamental artwork on ACP Sheet with

weather proof lamination. All anchorage and fastening of miscellanies metal items shall be

structurally adequate and finish to match surface. Providing earth work excavation for

installation and displaying pylon sign board of pit size 2x2x3' with providing cement concrete

ratio 2:4. All curved areas are free from kinks anchor fastener bolts and fastening devices are non

corrosive materials. and with all required infrastructure and hardware items etc., complete. For

finished item of work. (Size 10' x 4')

Supplying and fixing of Welcome Display sign. Providing MS box frame pylon structure of 38mm x

38mm MS square pipe with fabricating, grinding, zinc premier emulsion painting. Providing

approved colour ACP sheet of 4mm thick thickness with alloy grade 3105 H 14 PVDF coating for

anti fungal properties. Providing fabricating to the MS box for the ACP cladding with sub

structure fastening materials and hardware. items complete in line and level, heights and depths

with 789 silicon sealant. Providing opaque acrylic 3D letters of approved colours for displaying

the Pylon artwork content with 6mm thick and 0.40 transparency high tech plastic material

particularly high transparency and impact resistance levels. Providing computerized laser cutting

to the existing artwork design on the opaque acrylic sheet along with pasting on ACP sheet

backdrop. Providing HP Jet eco solvent print of existing ornamental artwork on ACP Sheet with

weather proof lamination. All anchorage and fastening of miscellanies metal items shall be

structurally adequate and finish to match surface. Providing earth work excavation for

installation and displaying pylon sign board of pit size 2x2x3' with providing cement. concrete

ratio 2:4. All curved areas are free from kinks anchor fastener bolts and fastening devices are non

corrosive materials. and with all required infrastructure and hardware items etc... complete. For

finished item of work. (Size 13' x 5')

Signature of Contractor With Seal Page 11 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Supplying and fixing of Direction Display sign. Providing MS box frame pylon structure of 38mm x

38mm MS square pipe with fabricating, grinding, zinc premier emulsion painting. Providing

approved colour ACP sheet of 4mm thick thickness with alloy grade 3105 H 14 PVDF coating for

anti fungal properties. Providing fabricating to the MS box for the ACP cladding with sub

structure fastening materials and hardware items complete in line and level, heights and depths

with 789 silicon sealant. Providing opaque acrylic 3D letters of approved colours for displaying

the Pylon artwork content with 6mm thick and 0.40 transparency high tech plastic material

particularly high transparency and impact resistance levels. Providing computerized laser cutting

to the existing artwork design on the opaque acrylic sheet along with pasting on ACP sheet.

backdrop. Providing HP Jet eco solvent print of existing ornamental artwork on ACP Sheet with

weather proof lamination. All anchorage and fastening of miscellanies metal items shall be

structurally adequate and finish to match surface. Providing earth work excavation for

installation and displaying pylon sign board of pit size 2x2'x3' with providing cement concrete

ratio 2:4. All curved areas are free from kinks anchor fastener bolts and fastening devices are non

corrosive materials and with all required infrastructure and hardware items etc., complete. For

finished item of work. (Size 5' x 3')

Supplying and fixing of stainless steel Door Numbers sheet of 1mm thickness and 304 Grade (Non

corrosion). Providing artwork designing for displaying the Door Number content as per approved

by the dept. Providing electronic content sensor for tracing to the outline of the art work design

on stainless steel with engraving tool. Providing customized engraving to the art work design of

Door number content on stainless steel sheet. Providing required infrastructures and equipments

45 for access of customized engraving to operate the art work design content in appropriate Nos 300 358 - 107400

manner. Providing deco metallic painting of weather proof to the engraving text on stainless

steel sheet. Providing grinding, hair liner brush finish buffing and with installation on the

backdrop wall with drilling, anchor bolts and with required hardware items. All curved areas are

free from kinks anchor fastener bolts and fastening devices are non corrosive materials etc

complete., for finished item of work. (Size 4" x 2.5")

Signature of Contractor With Seal Page 12 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Providing opaque acrylic sheet Officers Name of approved colours for displaying the Officers

Name Plates content with 4mm thick and 0.40 transparency high tech plastic material.

particularly high transparency and impact resistance levels. Providing opaque acrylic 3D letters of

approved colours for displaying Name Plates content with 6mm thick and 0.40 transparency high

tech plastic material particularly high transparency and impact resistance levels. Providing

46 computerized laser cutting to the existing artwork design on the opaque acrylic sheet along with Nos 50 2623 - 131150

pasting on Acrylic sheet backdrop. Providing HP Jet eco vent print of existi ornamental artwork

on Opaque Acrylic sheet with weather proof lamination. Providing stainless steel studs to the

acrylic Name plates for installation with water level alignment and required hardware items. All

anchorage and fastening of miscellanies metal items shall be structurally adequate and finish to

match surface etc., complete. For finished item of work.

Toilet Signage :- Providing and Fixing Toilet Signage to be made of Acrylic (6mm Thickness) Plate

Laser cutting, Buffing and deco painted, Front side would be applied with 3M Graphic, 3M Scotch

print decorative graphics on IJ180C (with controltac & comply feature for direct, bubble-free

application on walls) with UV protective matte overlaminate 8520 with a polyethylene-coated

paper liner. Customised imagery & the thickness of 2 mil (0.05mm) without adhesive & 3-4mil

(0.8- 0.10mm) with adhesive, having minimum tensile strength of 5 pounds/inch at 73°F (0.9

kg/cm at 23°C). The adhesive should be Pressure activated, positionable, with air release

channels and Signage would be fixed on existing surface with 3M VHB tape, as per approved

artwork. (Size 5"X5")

Push and Pull Signage:-Providing and fixing Push and Pull Signage to be made of Acrylic (6mm

Thickness) Plate Laser cutting, Buffing and deco painted, Front side would have 3M Graphic

application, 3M Scotch print decorative graphics on IJ180C (with controltac & comply feature for

direct, bubble-free application on walls) with UV protective matte overlaminate 8520 with a

polyethylene-coated paper liner. Customised imagery & the thickness of 2 mil (0.05mm) without

adhesive & 3-4mil (0.8-0.10mm) with adhesive, having minimum tensile strength of 5

at 73°F (0.9 kg/cm at 23°C). the adhesive should be Pressure activated, positionable, with air

release channels and Signage would be fixed on existing surface with 3M VHB tape, as per

approved artwork.(Size 6"X1.25")

Signature of Contractor With Seal Page 13 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Ceiling Signage :- Providing and fixing Ceiling Signage Signage to be made of Acrylic (6mm

Thickness) Plate Laser cutting, Buffing and deco painted, Front side would have 3M Graphic

application, 3M Scotch print decorative graphics on IJ180C (with controltac & comply feature for

direct, bubble-free application on walls) with UV protective matte overlaminate 8520 with a

polyethylene-coated paper liner. Customised imagery & the thickness of 2 mil (0.05mm) without

adhesive & 3-4mil (0.8-0.10mm) with adhesive, having minimum tensile strength of 5

at 73°F (0.9 kg/cm at 23°C). the adhesive should be Pressure activated, positionable, with air

release channels and Signage suspended with stainless Steel hanger, as per approved

artwork.(Size 18"X6")

Floor Directory Signage:- Providing and fixing Floor Directory Signage to be made of Acrylic (6mm

Thickness) Plate Laser cutting, Buffing and deco painted, Front side would have 3M Graphic

application, 3M Scotch print decorative graphics on IJ180C (with controltac & comply feature for

direct, bubble-free application on walls) with UV protective matte overlaminate 8520 with a

polyethylene-coated paper liner. Customised imagery & the thickness of 2 mil (0.05mm) without

adhesive & 3-4mil (0.8-0.10mm) with adhesive, having minimum tensile strength of 5

at 73°F (0.9 kg/cm at 23°C). the adhesive should be Pressure activated, positionable, with air

release channels and Signage would be fixed on existing surface with 3M VHB tape, as per

approved artwork.(Size 16"X18")

Directional Signage - Providing and fixing Directional Signage to be made of Acrylic (6mm

Thickness) Plate Laser cutting, Buffing and deco painted, Front side would have 3M Graphic

application, 3M Scotch print decorative graphics on IJ180C (with controltac & comply feature for

direct, bubble-free application on walls) with UV protective matte overlaminate 8520 with a

polyethylene-coated paper liner. Customised imagery & the thickness of 2 mil (0.05mm) without

adhesive & 3-4mil (0.8-0.10mm) with adhesive, having minimum tensile strength of 5

at 73°F (0.9 kg/cm at 23°C). the adhesive should be Pressure activated, positionable, with air

release channels and Signage would be fixed on existing surface with 3M VHB tape, as per

approved artwork.(Size 16"X18")

Signature of Contractor With Seal Page 14 of 15 NBCC

Signage, Equipments, Solar and other Misc works for permanent campus of NID AP

DSR-14 Rate Amount

Item No Item Description Unit Qty.

NS DSR NS DSR NS

Fire Extinguisher :- Signage made up of 5 mm Sun Board base sheet with photoluminescence film

pasted from behind and cut as per letters and designs and with border etc., 3M Clear Graphics

would be apply on the face of Signage Durable inkjet printed 3M Scotch print graphics on 3650-

114 self-adhesive vinyl, special CLEAR film to produce coloured imagery on glass with 8520

52 overlaminate with a polyethylene-coated lay flat liner. Customised imagery & the thickness of 2 Nos 25 298 - 7450

(0.05mm) without adhesive & 3-4mil (0.8-0.10mm) with adhesive, having minimum tensile

strength of 5.5 pounds/inch at 73°F (0.9 kg/cm at 23°C), the adhesive should be Pressure

activated, positionable, with air release channels complete as per drawings and details and as per

specifications fixed on wall/marble using approved adhesive (Size 6"X6")

Fire Exit Signage :- Providing Signage's Vinyl Cut (3M 3630 cast Translucent film of approved

shade the vinyl should be 2-mil thick with out adhesive & With adhesive: 3 to 4 mils (0.08 to 0.1

mm), long-term cast vinyl films with a synthetic lay flat liner that is not affected by water or

humidity. The film should be plotter cut as per the approved design) on photo luminescent U100,

3MM Aluminum Sheet of 1.0mm (+- 10%) Containing lumigen 11 as base chemical, covered

under UV Stabilized coating of appropriate. and fixing with S S Hanger. Design as per Architect

Approval.(Size 14"X6")

Providing & Fixing of 18 gauge Stainless Steel plates of grade 304 engraved with approved matter

single side writing all complete as per sample approved and fixed with stainless steel srew/

double side tape of 3M make required nos of holes, wherever required complete as per direction

of Unit Incharge.

Subtotal (F) - 2794199.38

Signature of Contractor With Seal Page 15 of 15 NBCC