80926 Special Repair to Bldg No T-166 at Jal Vihar GE Haddo

Amount

Dismantling plain or corrugated steel sheeting any guage, thickness including nainital or similar pattern roof covering.

S&F for pre-painted Galvalume steel sheets of Trapezoidal profile having pitch 190mm, depth 29mm and thickness 0.50mm (Galvalume base-PPGL trapezoidal profile sheets) fixed with self tapping screws neoprene and EPDM washers of suitable size in roof covering

S&F for pre-painted aluminium zinc steel sheets (Galvalume base-PPGL profile sheets) of thickness not less than 0.50mm in ridges, hips, valley gutters, drip and straight flashing cut to length & bent to shape girth sheets fixed with aluminium self staging

M&L for aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering.

M&L Bands strap, supports, stays for rain water ,ventilating pipes, including bolts, if required, hookes (stay), heavy for large gates, hook and pintel hinges, large hasp & staples, chains, hand made sliding bolts, clamps, hold fasts, hookes for hanging fan.

Dismantling wooden boarding, any description fixed in any position with nails as in eves & barge boards.

M&L for boarding (eaves / barge board) with 19mm thick plywood (BWR) fixed with screws on flat iron supports including applying two coats of synthetic enamel paint over a coat of pink primer.

Dismantling timber scantlings 40 Sq cm and over in section in any position unframed work.

M & L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified.

Dismantling of structural steel of any description not otherwise provided for all as specified

S&F rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410-W (Gde E-250) quality-A complete all as specified.

S&F for framed work such as grills, gratings etc with ends of bars shouldered and or riveted or forged Into spikes framed grard bars, barred iron doors, ladder, framed balusters, walk ways, railing frame work of water tanks and similar work conforming to Fe-410-O or Fe-310-O.

M & L for MS plate not less than 8mm thick with revated, bolted or welded attachment to columns or beams complete all as specified.

M&L for mild steel screw bolts (machine made) with hexagonal or square heads 5 to 10mm dia of nack & length n exc 5 cm at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut any type and size complete.

Dismantling wall & ceiling boards (fibre,insulation etc) or insulation boards, slabs, blankets any thick ness including cover fillets.

M&L for anodised aluminium snap grid frame work for ceiling 605mm x 605mm using aluminium anodised sections as specified in SSR Part-I-2004 including cutting, drilling, jointing etc complete including provn of 3.15mm dia GI wire suspenders fixed with adjustable connectors and providing 4mm thick E-Boards (Classic) 600mm x 600mm size duly applied with two coats of oil bound distemper over a coat of primer all as specified.

Dismantling of floor /skirting ( terrazzo/ PCC / Ceramic Tiles) including cement mortar bedding (but not backing ) and removing the rubbish from the site.

M&L for Vitrified ceramic coloured tiles (of approved light shade) of size 600x 600mm, 9 to 10 mm thick in floor, set & jointed in neat cement slurry over & including of screed bed 20mm thick in CM 1:4 and pointed in coloured cement to match the shade of tiles over all as specified Make : jonson, kajaria, Orient,Somany

All as per item No. 18 but on vertical surfaces such as skirting, dados and riser etc over & including rendering in CM 1:3, 10mm thick all as specified.

M&L glazed ceramic tiles in vertical surface as in dado/skirting 450x350x7 mm thick set and over and including 10mm thick screed bed in CM 1:3 on verticle surfaces and jointed in neat cement slurry and pointed in white or colour cement to match the surface of tiles, complete all as specified and directed.

Fixing only in repairs for aluminium partition, windows and door with frame and shutters fully or partly glazed, sliding/ openable/ fixed/ fully glazed and panels with 12mm thick pre- laminated partical board including all fittings ( supply only floor spring, glass, Imax hinges, particle board, gauze will be measured seperately)

M&L for non-skid Ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. and over and including 15mm thick screed bed in CM 1:4 on floor surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for non-skid Ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. and over and including 15mm thick screed bed in CM 1:4 on floor surfaces, set and jointed in neat cement slurry and pointed in-white or coloured cement to match complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.

M&L for granite 18 to 20mm thick as in counter slabs of WHB (of any type) work (table rubbed and polished) in cooking plate forms, counter of WHB and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as speified and as directed by Engineer-in-Charge.

S&F 15mm bore PVC connection 600mm long with brass check nut on both sidies screw to iron pipes.

Supply and fix in repairs CP angle cock 15mm dia fancy type cast copper alloy (Make-Jaquar Cat. No. Con-053KN) or its Equivalent.

Supply and fix in repairs CP WHB mixtre cast copper alloy with central hole for WHB and long shank fancy type 15 mm bore complete all as directed.(Make-Jaquar Cat. No. Con-167KNB) or its Equivalent.

Supply and fix in repairs CP brass hot and cold 15mm dia wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting leg & wall flange complete all as directed.(Make-Jaquar Cat. Con-281KN) or its Equivalent.

Supply and fix in repair CP bib cock 15mm dia with crutch handle as approved fancy type long body (Make-Jaquar Con-107KN) or its Equivalent. complete all as specified and directed.

S&F in repairs CP overhead shower dia 105 mm round with revolving joints (with body rotation) & 115mm long arm shower with rabit cleaning system and all fittings Make - Jaquar OHS-1709 or its Equivalent as approved.

Supply and fix in repair CP bib cock 15mm dia with crutch handle as approved fancy type two way Bib Cock (Make-Jaquar Con-041KN) or its Equivalent. complete all as specified and directed.

S&F in repair Toilet paper holder Make : Jaquar Code (ACN-1153N) or equivalent in MARC / PLUMBER complete all as specified and directed.

S&F in repair CP single towel rail 600 mm Make : Jaquar (AQN-7711) or equavalant in MRAC/PLUMBER complete all as specified and directed.

S&F in repair Soap dish Make :Jaquar Code (AQN-7731) or its Equivalent complete all as specified and directed.

S&F in repairs concealed stop Cock with wall flange incl all fittings complete all as specified and as directed.Make : Jaquar Cat No. CON - 083 KN or its Equivalent.

M&L for PVC SWR floor trap plain with grating including jointing with solvent cement diameter of outlet in 75mm.

M&L for PVC (SWR) gully trap, 125/110mm setting and jointing with solvent cement.

Taking down GI tubing 15mm dia, with connections.

Taking down GI tubing 20mm dia, with connections.

M&L for 25mm outer dia 3 layer PP-R Polypropylene random copolymer pipes SDR 7.4 UV stablised and antimicrobial welded having thermal stability for hot and cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors etc.

All as per item No. 41 above but outer dia of pipe 32 mm

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/roof etc complete.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors.

S&F PVC (SWR) bends any radius 110mm bore dia.

S&F 75mm bore PVC (SWR) branch piece, single (single y) equal or un equal.

Dismantling of 100mm dia cast iron / PVC Pipe or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required

S & F PVC pipe 110 mm bore, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors

S & F 100mm bore dia PVC pipe soil, waste and vent pipes, in any length with or without ears with cement joints, fixed to walls.

S & F in repair PVC (SWR) 'P' or 'S' trap floor trap 100 mm out let dia with grating including jointing to waste pipe complete

S & F in repairs PVC (SWR) bend 110mm dia with oval access doors of any radius fixed to soil and vent pipe and jointing with cement mortar complete

S & F 110mm bore PVC (SWR) junction (single T) equal or unequal

M&L in repair PVC Flushing cistern 10 ltr capacity high or low level including bracket & flush pipe etc all as specfied and directed.

S & F white vitreous china wash down water closet EWC (pedestal pattern) with PVC seat cover with mild steel chromium plated aluminised hinging device including connection to drain pipe and flushing pipe all as specified.Make : Johnson, Parryware or equivalent

S & F in repairs wash hand basin vitreous china white (flat back) of size 550x400mm including CI bracket 15mm dia polythene connection 32mm dia waste coupling and 32mm dia PVC waste pipe 90cm long etc. complete all as specified.

S & F in repairs Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor

S & F health faucet, brass, chromium plated with 8mm dia, 1.0m long flexible tube with wall hook, screwed for iron pipe or brass ferrule 15mm dia or bore, fixed in repairs complete all as specified and as directed. Make : ZIM Cat Part No 1624A or Equivalent in Prayag/Parryware

S&F in repairs corner glass shelf with brackets. Make : Jaquar Cat No. CAN 1173

Dismantling PVC water tanks exc 500 & n exc 1000 ltrs and removing to store

S&F 1000 Ltrs PVC tank 3 layered (ISI Marked) rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified and as directed by Engineer-in-Charge.

S&F in repairs 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, Cleaning, etc. and hoisting if required reconnecting and re-fixing in position.(Cleaning repairing, etc. measured separately) Exc 500 & n exc 1000.

Taking down chowkats or frames (With out taking of shutters) not exceeding 1.5 Sqm each.

Taking down chowkats or frames with shutter (With out taking off shutters) exc 1.5 Sqm but n.exc 4 sqm each.

Taking down shutters of any description n exc 1sq. m each

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each

Taking down Wall panelling and similar work

S & F II nd class hardwood plain, solid, straight, chowkats and frames, wrought rebated on the solid, rounded or chamfered put together with glue pinned at joints.

S&F 35 mm thick IInd class Hardwood plain, framed, paneled shutters (any number of panels), with panels of 12mm veneered particle board medium density, wood particle board with commercial face veneers.

S&F 35 mm thick glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc size of members as specified in SSR Pt-I section 8 clause 8023 (a), in II nd class hard wood.

M & L for 35 mm thick IInd class Hardwood for wrought treads with rounded nosings, with 20 mm wrought risers on tongued both edges, glued, wedged and blocked complete

S & F Solid PVC Door frame of size 50 mmx 47 mm made out of 5mm plain colour PVC sheet reinforce with M.S square tube, high strength suppling & fixing in opening as per specification

S&F Factory Made Solid PVC Moulded Door Shutters with Particle board core 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face supplying & fixing in frame at site as per specification & drawing suppling & fixing in the frame at site as per specification.

M&L flat iron as in hold fast and similar work.

S&F 150mm extruded aluminium alloy handles fabricated type anodised.

S&F 75mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21

S&F MS butt hinges medium weight but 100mm long (ISI)

S&F 200mm extruded aluminium alloy tower bolts extruded sections anodised.

S&F 100mm extruded aluminium alloy tower bolts extruted sections anodised.

S&F 100 mm size brass handles, fabricated type polished.

S & F floor door stopper of brass body and tongue with hard drawn steel spring overall length of cover plate150mm.

S&F aluminium sliding door bolt 300mm with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed

S&F in repairs aluminium wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed with aluminium wire staples all as specified and as directed by Engineer-in-Charge.

Supply only aluminium expanded metal fly proof mesh cut to size,0.45mm nominal dia of wire and average width of aperture 1.40 mm complete.

Supply only 4mm thick sheet glass, ordinary quality in squares n.exc 0.50 sq.m in each pane.

S&F 5mm thick looking mirror 25mm beading all around and fixed 6mm thick plywood on back face.

M&L for aluminium partition, window and door with frame and shutters fully or partly glazed , sliding / openable / fixed / fully glazed and pannels with 12mm thick pre-laminated partical board including all fittings (supply only floors spring, glass, Imax hinges, partical board, gauze will be measured separately) the size of aluminium sections shall be all as specified in relevant IS code and SSR Part-I.

S&F aluminium grill on U channel fixed to window frames

Supply and fix in repair stainless steel IMAX hinges for aluminium window shutters.

Supply only 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

S&F mild steel powder coated curtain rods includng side globin and end brackets including 10 Nos riges per RM.

S&F Factory Made Solid PVC Moulded 20 mm thick as in sides/back face of cupboards complete all as specified.

S & F Continuous (piano) hinges, Brass body, bright finish or electrogalvanised Width of flaps (when open) 40 mm complete as specified.

M&L for providing cement concrete type B0 1:2:4 (using 12.5mm graded aggregate) as in copings/ roof kerbs rounded or chamfered on edges (inclusive of necessary form work).

M&L Mortice lock, 2 lever Brass body, vertical type, size100 mm Make: Godrej or equalent.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete.

S&F Hasp and staple, 150mm long safety type, brass with aluminium anodised hinge pin including bolt to hinge plate and fixed with screws

S&F in repairs small articles such as door / windows / pelmet brackets stopper of 2nd class hard wood not exc 200 cu cm each including 50 mm long medium qulaity MS butt hinges including two coats of synthetic enamal painting over a coat of primer complete all as specified.

S&F cast iron door closer Aluminium (Diecast) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

Cutting holes for inserting hold fast and making good to the disturbed portion with cement mortor 1:3 or PCC 1:3:6 exc half brick wall n. exc one brick wall.

S&F in repairs CP grating 125mm dia round with or without waste hole fixed on floor/nahani trap fixed with cement mortar complete.

S&F in repair Mirror cabinet PVC/fiber of size 550 x 520 x 100 mm with sliding mirror 4mm thick of size 240 x 290 x 2 Nos with built in rack of size 230 x 150 x 90 mm with PVC plug etc with CP towel rail of length 270 mm and 100 mm dia.(Make:Supreme)

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including waste coupling & waste pipe, bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420

Demolition of cement concrete block masonry work on any description and in any position.

M&L for precast cement concrete block masonry with solid blocks using PCC 1:3:6 type C1 exc.10cm in width and setting in CM 1:4 complete all as specified.

Material & labour for Precast cement concrete block masonry 1:3:6 type C-I with solid block n exc 10 cm in width and setting in cement morter 1:4 complete all as specified and directed by Engr-in-charge.

Taking down cement plaster of any discription.

M&L rendering 15 mm thick in CM(1:4) on brick walls or concrete surfaces finished even and smooth without using extra cement.

M & L Rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete surfaces all as specified finished even and fair without using extra cement

M&L for preparation of new plastered surfaces of walls & applying two coats of oil emulsion distemper over a coat of primer.

M&L for complete removal of existing treatment on wall and applying two coats of oil bound distemper over a coat primer.

M&L for complete removal plastered surfaces of ceiling and applying two coats of distemper oil emuslion over one coat primer.

M&L for complete removal of surfaces of walls and applying two coats of anti-fungal exterior acrylic emulsion paint over a coat of primer.

M & L for applying wall care putty, 2 to 3 mm thick on wall surface

M&L for preparation of new plastered surfaces of walls and applying two coats of anti-fungal exterior acrylic emulsion paint over a coat of primer.

M&L preparing new surfaces of wood or wood based material exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of wood primer.

M&L preparing old surfaces of wood or wood based material exc 10cm width or girth and applying one coat of synthetic enamel paint.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer.

Providing and injectiong chemical emulsion for post constructional anti termite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub-structure to a depth

M&L for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

M&L for post construction ATT treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2.

M&L for post construction ATT at point of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/ hole by drilling 6mm dia holes at downward angle of degree at 150mm centre to centre and sealing the same

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) and removing the rubbish from the site.

M & L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate)for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for Reinforced cement concrete (nominal mix) Type B1 1:2:4(20 mm graded aggregate) for chajjas complete all as specified and directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Taking down old plaster / concrete from the slabs by chipping, chiseling upto depth of 20mm thick average including existing membrane and removing the debris from the out site of Defence Land and cleaning the surface with clean water , etc. completely.

M&L for applying a slurry bonding coat on the RCC roof slab surface using Nito Bond AR manufactured by M/s Fosroc Chemicals India (P) Ltd / equivalent in Dr. Fixt or Harjas Coating & Polymers (Coverage of 4 to 5Sqm / Ltrs) all as per manufacturer's instructions.

M&L for plastering the slab 20mm thick (1:3) using Nito Bond SBR of Fosroc @ 7 Ltr per bag of cement or equivalent make of Dr.Fixit of Pidilite Industries or of Harjas Coatings and Polymers.

M&L for applying two coats of high performance elastomeric cementious water proofing coating on external wall surfaces using Brush Bond RFX components (i.e, mixture of powder 15 kilogram + Nito Bond BBX 4.8 litres + clean fresh water 3 litres) of M/s Fosroc Chemicals (I) Pvt Ltd or IPH Resin & IPH 21 Hardner in proportion of 2:1 all as directed by Engineer-in-Charge. Make : M/s Fosroc Chemicals (I) Pvt Ltd or Harjas Coating and Polymers or Equivalent make of Dr. Fixit of Pidilite Industries.

Removing loose and broken concrete carefully by chiseling/ picking etc upto a depth upto 40mm from columns, beams, ceiling and similar structural members cutting edges, cleaning the dismantled portion with wire brushes etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and washing with clean water all as specified by Engineer-In- Charge. Note : Safety precaution shall be ensured by the contractor while carry out the work

M & L for applying one coat of anti corrossive primer @ 0.25 Ltr/ Sqm for the steel area to exposed old and new reinforcement to the full circumference and length of bars to form unbroken 40 micron thick film all as specified and directed by Engineer-In-Charge. Note : Nito Zinc Primer of FOSROC or Equivalent make of Dr.Fixit of Pidilite Industries or IPH-RB 107 & IPH RB 167 of Harjas Coating and Polymers.

S & F high strength deformed TMT steel bars 10mm dia and over cut to length, bent to shape required, including cracking, bending spirally for hooping for columns/ beams, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia

S & F high strength deformed TMT steel bars 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia

Drilling holes in slab/ wall/ column/ Beams for Anchor steel reinforcement including washing with water, 10mm dia of hole/ 150mm depth of holes inserting lock fix 'S' or 'P' in the holes and all as specified and as directed. Make : Lock Fix 'S' or 'P' of M/s Fosroc Chemical (I) Pvt Ltd or equivalent make of Dr.Fixit of Pidilite Industries or of Harjas Coating and Polymers.

M & L for appltying one coat epoxy bonding agent as per manufactures instruction to old concrete surface of columns, beams, ceiling and similar structural members all as specified and directed by Engineer-in Charge. Make : Nito Bond EP of FOSROC or Equivalent make of Dr.Fixit of Pidilite Industries or IPH-21EB of Harjas Coating and Polymers.

S & F for hard drawn steel wire fabric not exceeding 4 Kg/ Sqm cut to lengths, bent to shape mild steel wire, (annealed) not less than 0.9mm dia as in reinforcement as directed by Engineer-In-Charge.

M & L for pressure guniting 40mm thick at a pressure not less than 6kg/cm2 to surface of columns, beams, ceiling and similar structural members in cement mortar 1:3 duly modifying the mortar with admixture of IPH-CC Resin and IP-CC Hardner of M/s Harjas Coating Polymer Ltd in equal proportion @ 5% by weight of cement or Nitobond SBR of forsoc chemicals Indian Pvt Ltd @ 7 Ltr for 50 Kg bag of cement as directed by Engineer-In-Charge including necessary scaffolding, T & O etc complete all as directed.

M & L for applying curing compound on freshly concrete surface and plaster surface all as specified. Make : Concure WB of FOSROC or Equivalent make Dr.Fixit of Pidilite Industries or of Harjas Coating and Polymers.

M & L rendering 15mm thick in cement mortar 1:3 using river sand on guniting surface finished even and smooth without using extra cement mixed ( Nito Bond SBR of FOSROC @ 7 Ltr per bag of cement)/ Equivalent make of Dr.Fixit of Pidilite Industries or @ 5% by weight of cement of Harjas Coatings and polymer. Over the old cleaned surface of any description complete all as specified and as directed. Note: Safety precautions shall be ensured by the contractor while carry out the work.

Taking down old plaster on walls/ceiling by chipping, chiseling upto depth of 20 mm thick average and removing the debris from the site and cleaning the surface with clean water etc. completely.

M&L for applying a bonding slurry coat on the wall and ceiling surface up to depth of 20 mm using Nito Bond AR manufactured by M/s Fosroc Chemicals India (P) Ltd / equivalent in Dr. Fixt or Harjas Coating & Polymers (Coverag of 4 to 5Sqm / Ltrs) all as per manufacturer's instructions.

M&L for plastering the external wall surfaces 20mm thick (1:3) using Nito Bond SBR of Fosroc @ 7 Ltr per bag of cement or equivalent make of Dr.Fixit of Pidilite Industries or @ 5% by weight of cement of Harjas Coatings and Polymers.Make : Nito Bond SBR and Nito Bond AR of FOSROC or equivalent make of Dr.Fixit of Pidilite Industries or of Harjas Coatings and Polymers.

Cutting out existing cracks in concrete surfaces / masonary wall / slab forming grooves of 25mm x 40mm size, cleaning the groove thoroughly with blower, applying primer coat of the mix of IPH CC or Hydroseal Siliconate Epoxy Resin & Hardner in equal proportion with spray gun suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC in equal propotiol of make Harjas Coating and Polymers or Hydroseal Siliconate Epoxy resin,hardner and admixture in the proportion of 1:1:2 and finally applying the sealing coat of the same mix and in the manner primer coat is applied with following min. coverage per running metre length of groove

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc.

Taking down fuse Unit/DBs with MCB/MCCB 415 Volt/230 Volt

Taking down light fittings of any type complete all as directed.

Taking down old aluminium sub main wiring of any size.

M & L point wiring complete with 1100 volts grade, 1.5 sq.mm (nominal area), single core, FRLS PVC insulated ,unsheathed, multi stranded copper conductor cable drawn through and including medium grade, rigid , non-metallic PVC conduit of size not less than 20mm dia, with all necessary fittings, concealed in walls/roof/floor duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth dolly including suitable size of factory made fabricated MS sheet modular terminal box, flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete all as specified for the following :- Make:- Havell,s/Finolex/Gloster/Polycab

One light/fan point controlled by one modular switch 5 Amps one way.

One modular 3 pin 5 Amp socket out let on independent board.

One modular 3 pin 5 Amps switch socket on same Board

One light point controlled by two 2-way modular switches,

One bell point controlled by one modular bell push switch 5 Amps one way.

All as per item No.149 above but point wiring with 4.0 sqmm PVC FRLS insulated multistranded copper conductor suitable for one 3 pin 15 Amps socket out let and Geyser and one run of 4.0 sqmm cable for earth in green colour on independent board.

S & F modular stepped type electronic fan regulator 120w-2 module on the existing phenolic laminated sheet as per speicifed.Make: Roma(Anchor)/Legrand/Havells

S & F modular switch 6/10 Amp one way 230 V AC Make : ROMA(Anchor)/Havells (Crabtree)/Legrand

S & F modular switch 6/10 Amp two way switch 230 V AC Make : ROMA(Anchor)/Havells (Crabtree)/Legrand

S & F modular socket outlet 6/10 Amp intel multi socket for all pins 230 V AC. Make : ROMA(Anchor)/Havells (Crabtree)/Legrand

S & F modular socket outlet 16/20 Amp socket heavy duty 230 V AC Make : ROMA(Anchor)/Havells (Crabtree)/Legrand

S & F modular switch 16/20 Amp one way 230 V AC Make : ROMA(Anchor)/Havells (Crabtree)/Legrand

S & F modular bell push 5Amps flush type 230v, 50Hz AC. Make : ROMA(Anchor)/Havells (Crabtree)/Legrand

S & F Ceiling rose PVC polycarbonate , isolated body 3 terminals 230 V complete.

S & F , Electric Bell, Ding dong type working on 230 volts AC supply complete all as directed. Make: Anchor/Kinjal/Standard

S & F communication modules for TV socket sap code no.ACAKTOW000. Make: Havells(crabtree)/Anchor/Bajaj

S & F communication modules for tele socket RJ 11 2 Gang Tele socket sap code No.ACAKRTW112. Make: Havells(crabtree)/Anchor/Bajaj

Supply and laying of rigid non metallic PVC conduit of 25mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers lock nuts, saddles pipe hooks etc all as directed.

Taking down carefully ceiling fan of any make, size from its location, handed over to AGE E/M store yard without any damage and S & F Ceiling fan 5 star rated, 1200mm sweep, (white colour) working on single phase 230 volts, 50Hz AC complete with down rod and canopy including electric connection from ceiling rose to fan connector with PVC insulated 3 core copper cable of size of 0.75 sq mm complete all as per directed. Make: Havells (Model No. ES-40)/Bajaj/CG

Taking down carefully Exhaust fan of any make, size from its location, handed over to AGE E/M store yard without any damage and S & F Exhast fan 380mm sweep, 900 RPM of model Turbo force working on single phase 230 volts, 50Hz AC supply complete with including electric connection from ceiling rose to fan connector with PVC insulated 3 core copper cable of suitable size of 0.75 sq mm complete all as directed. Make: Havells (Model Variant in Sweep)/CG/Orient/Usha

Taking down carefully Water heater of any make, size from its location, handed over to AGE E/M store yard without any damage and S & F Energy Efficient BEE 5 star rated water heater storage type of 25 liters capacity, vertical electric supplied and installed complete including flexible pipe for hot and cold water, dead weight pressure relese valve, Anchor fastner - 4Nos of suitable size all as directerd by Engineer-in-charge. Make: Havells( Model No Puro Turbo DX Cat No GHWAPXTWB025)/Bajaj/Racold.

S & F surface mounted 14 watts LED sleek with high output diffuser all as specified and directed. Make: CG(cat no. LCL-14 -CDL)/Havells/Phillips/equivalent in Bajaj

M & L for sub main wiring with FRLS PVC insulated, 1100 volts grade single core multistranded copper conductor cable conforming to IS specifications with 2 runs of 6.0 sqmm & one run of 6.0 sq.mm single core multistranded copper conductor FRLS PVC insulated cable as earth continuity conductor drawn through & including PVC conduit of 25mm dia. size and conduit accessories concealed in wall connecting to common earth dolly all as specified and directed. Note: (i)Three runs of cable and one run of conduit with necessary accessories will be measured as one unit length. (ii) The wiring shall be done in proper colour coding using red, yellow or blue for phase, black for neutral and green for earth leads.

M & L for sub main wiring with FRLS PVC insulated, 1100 volts grade single core multistranded copper conductor cable conforming to IS specifications with 2 runs of 4.0 sqmm & one run of 4.0 sq.mm single core multistranded copper conductor FRLS PVC insulated cable as earth continuity conductor drawn through & including PVC conduit of 25mm dia. size and conduit accessories concealed in wall connecting to common earth dolly all as specified and directed. Note: (i)Three runs of cable and one run of conduit with necessary accessories will be measured as one unit length. (ii) The wiring shall be done in proper colour coding using red, yellow or blue for phase, black for neutral and green for earth leads.

S & F DB VTPN sheet metal enclosure double door suitable for incoming upto MCCB 160 Amps/200 Amps & outgoing MCB TP / SP (IP-43) Protection Triple pole and neutral 415 V 4 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete all as specified and directed. Make : Indo Asian/Havells/L&T

S & F single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 12 ways. Make: Legrand/L&T/Havells/ABB

Supply and Fixing 4 pole MCCB 125 Amp, 50 Hz, 415 V with rupturing capacity 25 KA complete all as specified and directed Make : Indo Asian /Havells/L&T

S & F MCB DP,40 amps, 10 KA , 230 volts , all as directed. Make: Standard /L&T/Havells

S& F MCB SP , 6-32 amps, 10 KA , 240 volts , Make: Legrand /L&T/Havells/ABB

S & F surface mounted 20 watts Astra with ultra bright LED tubelight luminier comprises of thermaly conductive material,pre wired with high effeciency electronic driver with high translucent frosted diffuser gets glare free,smooth light distribution model of Philips(BN150WLED20S-6500PSEODGR) LED tube light as directed by Engineer - in Charge. Make : Philips (BN308CLED20S-6500L120 PSU WH/CG / Bajaj

Supply and fixing round surface mounted LED panel.PDC aluminum housing and high translucent frosted plastic diffuser make it a robust Luminaire efficiency 100lm/watt, 6000K, 220V , 50Hz complete all as specified and directed. Make - CG cat No. LCDSPL-R-18- CDL/Philips Model No Star Surface/Havels

S & F of decorative wall mounting SS finish fixture with textured glass diffuser suitable for 4 watt LED B22 holder type light. Make- Havells (LHJE01106499)/CG/Philips /Bajaj

Taking down carefully existing electric energy meter of any capacity, any size and handed over to AGE E/M store yard and S&F AC single phase LCD meter 10-60 Amp wih optical port.(suitable for measurement of KWH only) all as directed. Make: L&T(WM101BC7DDH) /Schnider/Areva.

S&F polycarbonate sheet enclosure suitable for fixing of one single phase energy meter and one SPN MCB of capacity 40 Amp factory made concealed in wall all as directed.

S & F starter switch of capacity 25 amps, working on 240 volts AC supply and suitable for air conditioner all as directed.Make, Havells (ACTO202504) OR Phillips / Bajaj / CG

S & F building security light fittings 1x25 watt pinnacle NEO LED street light made up of pressure die cast aluminum housing with polycarbonate cover and high power LED and secondary lenses with IP 66 protection including suitahle GI bracket, clamps, nut, bolts and other related items for fixing the wall/surface suitable for 230volts, 50Hz AC supply all as directed by Engineer - in - Charge. Make: Crompton Cat No. LST-25-CDL or Phillips / Bajaj / Havells

Taking down old corroded GI bracket of 25 mm dia and supply and fixing new GI brackets of GI pipe light grade of size 25 mm dia including nuts, bolts and washers for building security light all as specified and directed

M&L for earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia as earthing lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion.

Supply & Fix 18mm thick factory made MDF board as in kitchen cabinets including shelves, sides and back side covered with the same board Fancy type handles, stainless steel automatic hinges complete all as specified and as directed.and as directed. Make : Pearl or Equivalent

Supply & Fix stainless steel non magnetic multilayer feuba Nickle chrome plated plain basket of size 430 to 530mm as required complete all as specified and as directed. Make : Hettich/sleek

All as per item 184 but plate basket

All as per item 184 but glass basket

All as per item 184 but cutlery basket

All as per item 184 but partition basket

All as per item 184 but pullout basket

All as per item 184 but corner basket

Priya construction

DISHA ENTERPRISES

NAWAZ CONSTRUCTIONS

SHUBHAM SHANKAR GAIKWAD

kakolil trade agencies

RADHA GOVIND CONSTRUCTION

M/S TANISHA ENTERPRISES