ADDN/ALTN OF BLDG NO JP-205 AND PROVN OF BOUNDARY WALL AROUND SINGLE LIVING FOR WOMAN MIL POLICE IN CITY AREA AND PROVN OF 20 GEYSERS AT MH UNDER GE ALWAR

Amount

Surface dressing n.exc 15 cm deep in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M in depth for foundation and getting out in soft/loose soil all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm deep as in soft/loose soil copletete all as specified.

Removing excavated material n.exc 50M and depositing where directed at a livel n.exc 1.5M above the starting point at the descriation of contractor complete all as specified.

M&L plain cement concrete 1:4:8 type D-2 (40 mm graded stone aggrfegatet) as in foundations, filling & mass concrete complete all as specified.

M&L treating the backfill in contact with foundation at the rate of 7.5 litres of anti termite emulsion per square metre of vertical surface all as specified.

M&L treating the top surface of filled earth at the rate of 5 Litres of anti termite emulsion per square metre of surface all as specified.

M&L treating the soil under plinth protection at the rate of 5 Litres of anti termite emullsion per square metre of surface area all as specified.

M&L hard core of broken stone or boulders of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

M&L form work to sides and soffit of roof or floor beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and roof beams etc rough finish flat surfaces on concrete complete all as specified and directed.

M&L use and waste of form work to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work, n.exc 200mm thick flat, rough finished surfaces of concrete complete all as directed.

M&L form work to edges of concrete flats, treads, breaks in floors, windows cills, concrete railings, floor and roof n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specifed and directed.

M&L M-25 RCC using 20mm graded stone aggregate as in roof beams, cantilevers, bressummers and lintels over 1.5m span complete all as specified and directed.

M&L M-25 RCC (using 20mm graded stone aggregate) as in slabs sopported on walls, beams and columns in floors, roofs etc complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, binding spirally for hooping end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. (MS TMT Bars shall be procured from main distributor or authorised supplier only).

All as per item No 15.00 above but 6 to 8mm dia.

All as per item No 15.00 above but 5mm dia and over up to & including 10mm dia in stirrups, spacers & binders.

M&L 40mm thick DPC to horizontal or vertical surfaces including necessary form work PCC 1:2:4 type B-0 using WPC @ 3% of cement by weight. (Integral WPC should be measured and paid separately).

Demolition of brick/stone masonry built in cement / lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified & directed.

M&L brick work with 'fly ash' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L brick work with old size 'fly ash’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. (Test certificate shall be produced as per IS-3495 and packed sample for testing).

Taking down cement plaster any description on brick or stone walls, PCC etc complete all as specified and directed.

M&L rendering 10mm thick internal other than fair faces surfaces in CM 1:6 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement all as specified and as directed.

M&L 15mm thick rendering fair faces of brick masonary in CM 1:4 mixed with water proofing compound finished with even and smooth mixed with Liquid Water Proofing admixture complete all as specified and directed. (Note : WPA shall be measured and paid separately under relevant item as supply only).

M&L rendering 5mm thick in CM 1:3 on concrete surfaces as in ceiling, beams, columns etc finished even & smooth without using extra cement complete all as specified.

M&L preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty of approved tint complete all as specified & directed.

M&L preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

M&L preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L preparation of old decorated plastered surfaces of walls and applying two coats of cement base paint of approved shade/tint complete all as specified & directed.

M&L complete removal of existing treatment on walls applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete all as directed.

M&L writing letters or figures (Block, Roman, Italic or Indian letter n.exc 30cm high) complete as directed.

Supply only integral water proofing compound. (Purchase vouchers shall be produced separately)

Demolition of cement concrete (un-renforced) in ground floor and paving not exc 15cm thickness (below or above ground level) & removal of rubbish material complete all as specified & directed.

M&L 100mm thick PCC (1:4:8) type D2 (using 40mm graded aggregate) as in sub base of flooring finished surface even and rough complete all as specified and directed.

M&L 25mm thick, PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in Sub base of floors, levelling course complete all as specified& directed.

M&L vitrified ceramic tiles 10mm thick (square/ rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 15mm thick screed bed in cement & sand mortar 1:6 all as specified and directed.

M&L vitrified ceramic tiles 10mm thick (square/ rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L coloured non skid ceramic tiles (1st quality) 7 to 8mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floors etc, laid over with and including 15mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L machine cut kota stone slab 20-25mm thick in steps for riser, dado, skirting, wall etc over with and including 20mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed. (Sample shall be approved from GE before execution of work).

M&L machine cut kota stone slab 20-25mm thick in steps for riser, dado, skirting, wall etc over with and including 20mm thick rendering in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L glazed ceramic coloured tiles in vertical surface 450mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over with and including 10 mm thick rendring in cm 1:4 complete all as specified & directed.

M&L granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20mm thick in CM 1:6 cement concrete complete all as specified & directed.

M&L 50mm thick sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n.exc 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) n exc 1.5 sqm each & removing to store.

M&L mild steel angle iron door frame of any size conforming to Fe 410-0 (Gde-E-250 ) incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified & directed.

S&F 35mm thick 2nd class hard wood factory made panelled door shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed.

M&L preparation of new wooden surfaces over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

M&L preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed.

S&F 300mm helical/rat tail door spring 300mm size with MS sheet wing pattern including roller plate complete as directed.

S&F solid PVC moulded door frame of size 50mm x 47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast.

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded Prelam PVC sheet on front face & 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification.

S&F 100 mm MS butt hinges medium weight cold rolled mild steel

S&F 150 mm aluminium anodised barrel tower bolts of extruded section complete all as specified & as directed.

S&F 150mm extruded aluminium alloy handles fabricated type, anodised complete all as specified & as directed.

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat, rubber beading for fixing etc. complete all as specified & approved by GE.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos), suitable handle (1 No) complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc complete all as specified & approved by GE.

S&F powder coated of any colour as approved anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified & approved by GE.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

S&F 4mm thick frosted glass with rubber bedding in square n exc 0.5 sqm in each pane complete all as specified & directed.

S&F 4.80mm thick sheet glass ordinary quality, in squares n.exc 0.5 Sqm each complete as directed.

S&F 4.80mm thick sheet glass ordinary quality, in squares exc. 0.5 Sqm each complete as directed.

M&L 75mm thick cement concrete (1:3:6) type C1 using 20mm thick graded stone aggregate as in plinth protection laid in alternate bays n exc 2.5m length finished even & fair and joint to be filled with Bituminous mastic filling including necessary form work complete all as specified and directed.

Demolition mud in roofs, any thicknes, including plastering, existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed.

M&L PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified & directed.

M&L 15mm thick screed bed on fair faces of concrete/ brick surfaces in CM 1:4 with water proofing compound @ 3 % of wt of cement finished even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete all as specified. (Polymeric membrane and WPC shall be meausred and paid seperately here-in-after).

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces over bituminious primer complete all as specified & directed.

M&L APP based plymeric membrane minimum weighing 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) land on primed surface by forced application, with and including applying two coats of reflective silver aluminium paint over APP membrane complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) of any thickness, including cover fillets complete all as specified and directed.

M&L false ceiling with ArmGyp-FB ceiling tiles 9mm thick of 595mm x 595mm (as approved by GE) fixed with and including galvanised iron powder coated inverted "T" or "L" section (concealed GI frame work) of mettalic or equivalent suspended from ceiling with provn of galvanised wire 4 mm dia and wall taping screw including butterfly clip, hold down clips for fixing the board to frame complete all as per manufacurers instructions all as directed and specified. (a) size of main tee 39 x 24.4 x 0.8 mm (b) size of wall angle 22.2 x 22.2 x 0.65 mm (c) size of grid 0.61 x 0.61 mm complete all as specified & directed.

Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal to store.

Taking up or down 20mm steel tubing and connections, including cleaning for re-fixing or removal to store.

S&F 15mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc all as specified and directed.

S&F 20mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified & directed.

S&F ball brass valves, high pressure, 20mm bore, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in position all as specified.

S&F in repair 20mm bore Gun Metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & as directed.

S&F 20mm bore Gun Metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & as directed.

S&F in repair 15mm dia PVC connecting pipe 450mm long with PTMT nuts of suitable size at both ends complete all as specified & as directed.

S&F in repair thin rim table top basin size 480mm x 380mm x 135mm including 32mm CP waste coupling & PVC flexible waste pipe of 90 cm long complete set all as specified and directed.

S&F in repair looking mirror 5mm thick including cutting, grinding, polishing and chamffering of edges of glass, fixed with and including 20mm dia fancy type stainless steel fixers 04 Nos complete fixed to wall all as directed.

S&F Brass chromium plated bottle traps 32mm dia for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified & directed.

S&F in repairs fancy type center 3-hole basin Mixer without popup waste system but including plain waste 32mm size with aerator complete cast copper alloy, chromium plated, screwed down high pressure, with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

S&F in repair brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

S&F in repair 15mm bore fancy type long body bib taps, chromium plated alloy with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed.

S&F 15mm bore fancy type bib taps, half turn, chromium plated alloy with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed.

S&F in repair Stop/angle valves, fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed.

S&F Stop/angle valves, fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed.

S&F in repair PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC complete all as specified.

S&F in repair towel rail 600mm long of CP fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as directed.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

S&F in repair Vitreous China squatting pan, Orissa pattern, size 580mm x 440mm white with integral foot rests connection to trap and to flushing pipe, etc. complete including making good to floor complete all as specified & directed.

S&F in repair Brass chromium plated shower rose 125mm size fixed to 15mm bore pipe all as directed.

S&F in repair Jet spray chromium plated brass for EWC with & including PVC connection 900 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete.

S&F in repair mirror cabinet PVC frame of size 400 x 500 mm fixed to wall with rawl plug & stainless steel suitable size screws complete all as specified and directed.

S&F in repair glass corner shelf (Cat Part No T6010A1 of make – Parryware or equivalent ) complete all as specified & as directed.

S&F in repair stainless steel cloth hanger size of 300mm long with minimum 8 to 10 hooks each complete all as specified & directed.

S&F in repair grating doom 100 mm dia of PTMT (Minimum weight 25 gms) fixed with cement complete all as specified & directed.

S&F PVC connection 15mm size with PTMT nuts and 450mm in length complete all as specified & directed.

S&F in repair PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&F in repair 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors.

S&F PVC (SWR) bends 110mm dia any radius.

S&F PVC (SWR) junction single (Single T) equal or unequal with access door 110mm dia.

S&F PVC (SWR) Reducers 110mm to 75mm.

S&F PVC(SWR) Vent cowl 75mm dia.

S&F PVC (SWR) 75mm dia Floor Trap, plain with CP grating including jointing with solvent cement.

S&F 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work etc. including taking down existing frame work complete all as specified & directed.

S&F 75mm extruded brass handles, fabricated type polished complete all as specified & directed.

M&L 150 mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

M&L concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in 150mm bore pipe PCC for 1:4:8 type D-2.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggragate as in bed blocks, coping,manholes etc including weathering slightly rounded or chamfered angles and throating making grooves for fixing of man hole cover including necessary form work.

S&F 50mm thick steel fibre reinforced (SFRC) manhole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 3 ton /Sqm in square rectangular or Circular shape complete all as specified and directed.

M&L PCC 1:2:4 type B1 (20mm graded aggregate) cement concrete in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc complete all as specified and directed.

Dismantling framed timber scantlings 40 sqcm and over in section, in any position complete all as specified.

Excavation in post holes in soft loose soil (similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplush soil to a distance n exc 50m and making good surface complete all as directed.

M&L PCC type C2 1:3:6 (40 mm graded aggregate) Cement concrete in foundations, filling and mass-concrete complete all as specified & directed.

S&F MS steel work in tubular trusses and tubular posts including special shaped washers etc complete using but welded. RHS/SHS confirming to IS 4923 : 1997 with one shop coat of zinc chromate primer paint.

Dismantling asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings complete all as specified & directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof coverin/ cladding to wall fixed with self tapping screwas as specified or fixed with L type or J type hook bolts & washers etc complete all as specified & directed.

M&L plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) set in cement mortar 1:6 as in coping of brick masonry wall kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin) corbels, brackets, etc including weathering slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified & directed.

M&L providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding frame set in cement mortar Set in cement mortar 1:4 (type B-0 1:2:4) 12.5mm agregate complete all as specified & directed.

S&F framed work such as grills, gratings, etc with ends of barss houldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; frame work of water tanks and similar work framed with flat iron etc and hung asgates, conforming to Fe-290.

M&L 75mm thick PCC (1:4:8) type D2 (using 40mm graded aggregate) as in Sub base of floors, finished surface even and rough complete all as specified and directed.

M&L 60mm thick machine pressed precast conctete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 , M-35 Grade with and including 25mm thick sand filling, watering, consolidating before laying of paver block complete all as specified and as directed.

M&L precast cement concrete kerb stone solid block factory made in PCC 1:2:4 type B-1 using (20mm graded stone aggregates) set in CM 1:6 (size of precast concrete block complete all as specified & directed.

Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified & directed.

S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed fixed in repair with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed. (Note : Each line of wire to be measured).

S&F mild steel joist angle channel or tee sections and fix independently in concrete as fencing posts and similar work confirming to Fe 410 or Fe -310-0.

S&F galvanised steel puched type concertina coil of 1050mm dia (dia of coil when unstretched) and length of each coil 6 m after streching and fixed to angle iron post/strusts with 3.15mm dia GI wire all as specifed and directed.

M&L cutting and inserting TEE, L bow, bend/collar and tapping the connection from the existing 80/50mm DI/GI tubing line for taking branch connections including tapping accessories complete all as directed.

M&L point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke & heat (FRLS) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20mm external dia) but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part-I, ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLS PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0mm thick for one light point controlled by one way switch all as specified & directed. Note : The quoted rate shall be incuded cutting, chasing, making good of distrub surfaces including matching of existing colour surface of walls.

All as per serial item No 135.00 here-in-before but for one fan /exhaust fan point controlled by one switch and regulator.

All as per serial item No 135.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 135.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 135.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 volt complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Havells Cat Part No LHEXBLP7PN1W018 or equivalent of Surya/Philips/Crompton Greaves.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F MCB 32 Amps, single pole & neutral, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F MCB 6-32 Amps, single pole, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30 x 25 x 5cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos), complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 16 sqmm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

M&L brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (tibba sand) and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L 40mm grade GI pipe (light grade) for protection of LT cable fixed to wall /pole /road crossing including clamps complete all as directed.

M&L for drilling hole under road fro laying of U/G cable through pipe of suitable size complete all as specified and directed.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5m deep below normal ground level and connected to and including galvanized iron earth wire 4mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/test point/ panel/ equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

S&F ceiling fan 5 star rating 1200mm sweep 240V AC including provision of hook in ceiling of suitable size and necessary electric connection complete all as directed. Make : Havells/Crompton/Bajaj/Orient.

S&F LED type street DRACO Series light luminaire 20 watt 230V, 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed. Make : C&S Cat Part No LTESS20WLED or equivalent of Crompton Greaves / Wipro.

S&F exhust fan 300mm sweep 240V AC including provision of hole in wall of suitable size for fixing of exhaust fan complete all as directed. Make : Havells/Crompton/ Bajaj/ Orient.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2KW capacity 25 Litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, Connection piece etc. including necessary fixing arrangement with 4 Nos of Anchor bolt of size 10mm dia 150mm long with washers complete all as specified and directed. Make :- Bajaj / Crompton Greaves / Usha Lexus / Havell's or equivalant.

S&F sanitary napkin incinerator/disposal machine auto thermal & timer cut off fully automatic hygienic of capaciy 12-15 napkins burning capacity per cycle of size 250 x 250 x 530mm compatible for both wall and floor mounting complete all as specified and directed.

M&L sub main wiring with four runs of 4 sqmm (nominal area) size main cable & one run of 2.5 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked (IS: 694) cable, drawn through & including suitable size of heavy duty PVC conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling complete. Note:- 4 runs of 4sqmm size, 1 run of 2.5sqmm size cable & conduit with accessories shall be measured as one run length for payment purpose. Make of conduit : Finolex/Atlas/Kalinga/ Supreme/Bajaj. Make of cable :Havells/Polycab/ Finolex/KEI or as approved by GE.

S&F metal clad plug and socket board SP&N enclousure with 2 Pole and earth metal plug and socket complete with 20 Amp MCB SP 'C' cureve complete all as specified.

S&F MCB Single Pole 240 Volts, 10 KA, ‘C’ Curve, 25 Amps complete all as specified. Make :- Legrand/L&T (Hagar) / Siemens (Beta Guard)

M/S JINDAL ENTERPRISES

shiva construction

KARTIK ENTERPRISES

M/s S Amarjit Singh

Hitesh Construction

M/S GAURI CONSTRUCTION