ADDITION/ALTERATION TO ADM BLOCK OF AGNIVEERS TO INCL URINAL POINTS, BATHROOM BLOCKS, PAVED ACCESS AROUND THE BLDG AND ANTI SEEPAGE TREATMENT AT THE MARATHA LIRC BELAGAVI UNDER GE BELAGAUM

Amount

Demolition of brick work or stone/boulder masonary buit in cement mortar and including all quions, arches, pillars etc, but excluding ashlar facing dressed stone work and precast concrete complete all as specified and directed.

M&L pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6 type C1, using 20 mm graded stone aggregate, set in CM 1:6, complete all as specified and directed.

M&L RCC (nominal mix) type A1 1:1½:3 (20 mm graded crushed stone aggregate) as in chajjas and the like complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves and including supports, overhangs, etc. also splays between floors and beams, for fair finished surfaces complete all as specified and directed.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required and including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per Sl item No. 5 above but 6 to 8 mm dia.

S&F Ist Class hard wood external teak wood lipping, 6 mm thick on exposed surface of prelaminated particle board fixed with nails complete all as specified and directed

M&L 18/19 mm Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F in repair of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

S&F 25 mm thick, 2nd class hardwood planks for planed one side, with butt joints and fixed with nails supplied and fixed complete all as specified and directed.

All as per Sl item No. 10 above but in repairs to existing floors in patches, including cutting out, piecing, heading joints etc,

S&F high pressure steam cured (HPSC) non asbestos fibre cement building board 4 mm thick in false ceiling and including aluminum anodized snap grids of 60 x 60 cm in ceiling with Tee section 35 x 25 x 1.25 mm, angle section 25 x 25 x 1.25 mm thick and including 2 mm dia GI hanging wire and all hanger fittings etc, applying three coats of white wash on exposed surfaces of ceiling and dismantling ceiling and wall boards or insulation board of any thickness including cover fillets etc, complete all as specified and directed.

M&L 10 mm thick rendering in CM 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, rendering finished even and smooth (without using extra cement) and including taking down complete all as specified and directed.

M&L 15 mm thick rendering (in two coats 10 mm + 5 mm) on fair faces of brick work or concrete surface in CM 1:4 on external wall finished even and fair mixed with integral water proofing compound as per manufacturers instruction in 2nd coat and including taking down complete all as specified and directed. Note:- WPC will be measured and paid separately as supply only.

Supply only integral water proofing compond complete all as specified and directed.

M&L 5 mm thick rendering in CM 1:3 on concrete surface as in ceiling / chajja and RCC surfaces, finished even and smooth (without using extra cement) and including taking down complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L preparation of new plastered ceiling surfaces and including applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L complete removal of existing treatment on walls with wire brush, scrapping down smoke soot, mould, moss and efflorescent salts, trading oil and greasy spots, filling holes, cracks with cement base putty and including applying two coats of oil bound distember over a coat of alkali resistant primer complete all as specified and directed.

Material & Labour for complete removal of existing treatment on old walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc, all as specified and directed

All as per Sl. item No. 21 above but on ceiling

M&L preparation of new wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old painted wood and wood base surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of old painted steel surfaces of any descripation over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down chowkhat or frame area exc. 1.5 sqm but n. exc. 4 sqm each complete all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area n. exc. 1.5 Sqm each complete all as specified and directed.

All as per Sl. Item No. 28 above but area exc.1.5 Sqm and n. exc. 4 Sqm each

Supply and fix PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening but wood grain printed PVC sheet & edges will be painted to match printed sheet, etc complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 30 mm thick (stiles) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered wire heat strips of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, for fully gauzed, panel will be of wire gauze in lieu of single side prelam PVC sheet panel, the wire gauze shall be wrapped on an additional square 8 mm M.S. tubes. The wire gauze shall be stretched to tighten firmly with beading, and joined together with solvent cement and fixed in the frame at site all as per specification & drawing complete all as specified and directed.

M&L 2nd class hardwood for plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F Factory made 35 mm thick second class hard wood, plain, framed panelled shutters (any number of panels), with panels of 12 mm thick timber flat on both sides (feather edged), or of 12 mm thick veneered particle board medium density wood particle board with commercial face veneers as specified in clause 8.24 (a) of MES SSR 2009 Part I complete all as specified and directed.

S&F Factory made 35 mm thick second class hard wood, glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc, divided into squares, with plain chamfered or rounded, mitred and without sash bars, edges of framing plain, chamfered or rounded with cut mitred beds for securing glass etc, supplied and fitted to chowkhats as specified in clause 8.24 (a) of MES SSR 2009 Part I complete all as specified and directed.

S&F for collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc, as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

M&L aluminium anodised sliding windows (Triple track) with bottom track of size 92 x 31.75 x 1.6 mm, side and top frame of size 92 x 31.75 x 1.4 mm, top and bottom shutter rail of size 39 x 17 x 1.4 mm, outer style of size 39 x 17 x 1.4 mm, interlock style of size 39 x 27 x 1.4 mm and including 4 mm thick frosted sheet glass for panels with necessary hardware fittings such as handles, locking arrangements, rubber gaskets, rollers, spring catchers, wire mesh etc. complete all as specified and directed. Note: (i) Each window shall be provided with 2 Nos. of glazed shutters & wire mesh shutter of required size. (ii) Quoted rate shall be deemed to be inclusive of 4 mm thick sheet glass and SS wire mesh.

S&F mild steel framed work such as grills, grating etc, with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings and similar work conforming to Fe-290-0 or Fe Gde-165 including dismantling existing mild steel work of any description, complete all as specified and directed.

S&F anodised aluminium ventilator shutters fixed type without sash bar, aluminium section weighing 0.55 kg/m and including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, locking arrangement, etc. complete all as specified and directed.

S&F 300 mm long mild steel helical door spring, ordinary rat tail pattern spring and including roller and roller plate complete all as specified and directed.

S&F 100 mm long medium weight, cold rolled mild steel butt hinges complete all as specified and directed.

S&F 200 mm long MS steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm extruded aluminum alloy handles, cast type, anodized complete all as specified and directed.

S&F 150 mm MS pressed handles oval type stove enamelled black complete all as specified and directed.

S&F 300 mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 150 mm floor door stopper of aluminium alloy body and tongue anodised, with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.50 sqm in each pane complete all as specified and directed.

M&L 4 mm thick figured glass pin head type and glazing with oil putty in squares n. exc. 0.5 sqm in each pane complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame and including punching or drilling out old glazing pins / spring clips and providing and fixing new ones complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

All as per Sl. Item No. 50 above but in repairs.

S&F in repairs 25 mm dia curtain rod (curtain rails) alumunium alloy powder coated and including decorattive knobs complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in bed blocks for grouting hold fasts, coping, filling in pressed steel chowkat or similar work including necessary form work as required complete all as specified and directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

S&F wire mesh of size 20 mm, wire netting of galvanised steel wire 1.40 mm dis fixed with tinned tacks of wire stapples complete all as specified and directed.

S&F 4 mm dia galvanised steel wire, 150 x100 mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed.

M&L cutting holes exc. 250 sqcm but not ex.c 500 sqcm into or through cement concrete slabs, chajjas etc. reinforced or otherwise complete all as specified and directed.

Use & waste of formwork to chajjas, chullah hoods, troughs and similar items and including edges complete all as specified and directed.

M&L machine cut granite stone 18 to 20 mm thick, premium quality, any colour as in flooring, set and jointed with neat cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab including grinding the edges half round, rubbing and polishing over and including 20 mm thick screed bed in cement mortar 1:6 and demolition of stone slabs complete all as specified and directed.

M&L virified ceramic coloured tiles 9 / 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc, set and jointed in neat cement slurry to match and pointed in white or coloured cement to match the surfaces of tile laid over and including 15 mm thick screed bed in CM 1:4 and dismantling of tiling complete all as specified and directed

All as per Sl. item No. 60 above but in vertical surface such as skirtings, dados etc, over 10 mm thick rendering in CM 1:3.

S&F non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or colored cement to match and including 15 mm thick screed bed in CM 1:4 and dismantling of tiling complete all as specified and directed

S&F glazed ceramic coloured tiles 350 x 450 x 7 mm thick on skirting / dado etc, set and jointed in neat cement slurry and pointed in white or colored cement to match and including 10 mm thick rendering in CM 1:3 and dismantling of tiling complete all as specified and directed

M&L 20-25 mm thick machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding rubbing and polishing and exposed edges of kota stone shall be rounded complete laid over and including 20 mm thick screed bed in CM 1;6 complete all as specified and directed.

All as per Sl. item No. 64 above but in vertical surface such as skirtings, dados etc, over 15 mm thick rendering in CM 1:4.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thick above or below ground level complete all as specified and directed.

Disconnecting existing tanks of capacity 500 litre to 1000 litre from water supply conections, setting aside (or lowering if required) for repairs and including cleaning, re-hoisting, reconnecting and re-fixing in position etc, complete all as specified and directed.

S&F 25 mm PP-R Gate valves (brass insert) outer dia of pipes in 25 mm as per requirement of the site complete all as specified and directed.

M&L PCC 1:5:10, type E2 using 40 mm graded stone aggregate as in filling under sunken floors etc, complete all as specified and directed.

S&F in repairs vitreous china squatting pan, white, "Orissa pattern" of size 580 x 440 mm with integral foot rest excluding flushing cistern and flushpipe but including provision of 'P' trap and cement concrete bedding complete all as specified and directed.

S&F in repairs, vitreous china wash down water closet pan (pedestal pattern), white, including seat cover, connection to drain & or out going pipe MS CP hinges device, fixing bolts etc, complete all as specified and directed.

S&F in repairs 10 litre capacity PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets and PVC connection 450 mm long complete all as specified and directed. Make: Cat No. 507924 of Hindware or Equivalent in Parryware / Prayag / Cera

S&F in repairs, vitreous china wash basin, white, flat back, size 630 x 450 mm and including CI brackets, waste coupling, 32 mm dia LDPE waste pipe, 15 mm dia fancy chromium plated pillar tap and PVC connection 450 mm long complete all as specified and directed. Make: Model No. QT KVS -WHT-35935 of Jaquar or Equivalent in Hindware / Parryware / Prayag / Cera

S&F in repairs vitreous china urinal, full stall type, white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement and including 40 mm dia PVC waste pipe 610 mm long, flush pipe, grating and union for discharge pipe etc, complete all as specifed and directed.

S&F in repairs vitreous china white soap dish, approximate size 160 x 160 x 90 mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs chromium plated towel rail 600 mm long fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 170 grams) complete all as specified and directed. Make: Model No. ACN-CHR- 1111SM of Jaquar or Equivalent in Hindware / Parryware / Prayag / Cera

S&F in repairs 15 mm bore bib tap brass chromium plated fancy type screwed down for iron / GI pipe or for brass ferrule complete all as specified and directed. Make: Model No. QT F2006151 of Jaquar or Equivalent in Hindware / Parryware / Prayag

S&F in repairs angle / stop valve 15 mm bore, chromium plated, fancy type, with wall flange, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron / GI pipe or for unions complete all as specified and directed. Make: Model No. OPP-15083KPM / OPP15053PM of Jaquar or Equivalent in Hindware / Parryware / Prayag

S&F in repairs, health faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs, stainless steel grating with frame, dome type, 125 mm dia, with or without hole for waste pipe connection complete all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Supplying and laying of 20 mm dia outer diameter CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls / ceiling or laying in floors and including taking down existing GI / CPVC tubing and connection complete all as specified and directed.

Supplying and laying of 16 mm dia outer diameter CPVC pipes SDR 11 & plain CPVC SDR 11 fittings concealed on walls / ceiling or laying in floors, cutting chases and making good including taking down existing GI / CPVC tubing and connection complete all as specified and directed. Note : Quoted rate shall deemed to be include cost of cutting chases and concealing the pipe.

S&F 16 mm outer diameter CPVC brass elbow fittings on walls / ceiling or laying in floors complete all as specified and directed.

S&F 16 mm outer diameter CPVC brass Tee fittings on walls / ceiling or laying in floors complete all as specified and directed.

S&F 16 mm outer diameter CPVC male brass threaded adaptor (MTA/ MBTA) fittings on walls / ceiling or laying in floors complete all as specified and directed.

S&F 16 mm outer diameter CPVC female brass threaded adaptor (FTA/ FBTA) fittings on walls / ceiling or laying in floors complete all as specified and directed.

S&F 16 mm outer diameter CPVC union fittings on walls / ceiling or laying in floors complete all as specified and directed.

S&F in repairs, 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins etc, with long screwed shanks and fly-nuts, flange end bedded in red lead, cement and other end fixed etc complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes type 'B' single socketed in any length with rubber ring joints fixed to walls and including taking down old u/s pipe of any description complete all as specified and directed.

All as per Sl. Item No. 91 above but 75 mm bore

S&F in repairs, 110 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

All as per Sl. Item No. 93 above but 75 mm bore

S&F in repairs 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal with access door complete all as specified and directed.

All as per Sl. Item No. 95 above but 75 mm bore

S&F in repairs, 75 mm dia outlet, PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs, PVC (SWR) gully trap 125 / 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single T) equal or unequal with access door jointing with solvent cement complete all as specified and directed.

All as per Sl. Item No. 99 above but 75 mm bore

S&F 110 x 75 mm bore PVC (SWR) reducer including jointing with solvent cement complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and directed.

S&F rolled mild steel of joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc, cutting to lengths where required, notching, drilling, fitting, riveting and/ or welding or connecting with bolts and nuts confirming to Fe 410-W (Gde 250 quality 'A') complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering / cladding to wall, fixed with self tapping screws and EPDM washers etc, complete all as specified and as directed Note: Measurement shall be taken flat as fixed without any allowance for laps.

M&L 4 mm thick aluminium composite panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5 mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41) weight not less than 7.6 kg per sqm and including necessary sub-structures, anchors, hardware and fittings fixed over and including aluminium section of size 35 mm x 25 mm x 2 mm thick and panel all as per manufacturers instructions with necesary fittings and rubber beading and frame work in vertical surface complete all as specified and directed. Note: Measurement shall be taken flat as fixed without any allowance for laps & quoted rate is deemed to be include necessary scaffolding.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L 50 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection / path laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary formwork to divide the area in panels, including joints filling with sealing compound Grade 'A' complete all as specified and as directed.

M&L, PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in surface channels, drains finished even and smooth including necessary formwork complete all as specified and directed.

M&L, sunken floor treatment with APP modified water proofing membrane with the following specifications complete all as specified and directed :-

Removing existing floor treatment of any type and any description including taking down existing plastering of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris to a distance exceeding 50 m but not exceeding 100 m.

Brushing with neat cement slurry @ 3Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement.

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.3 litre per Sqm and providing APP modified water proofing membrane weight not less than 4.5 kg/Sqm reinforced with non oven polyester mat weight not less than 160 gms per Sqm and including min 10 cm side / over lap & including applying a coat of blown hot bitumen grade 85/25 at 1.2 Kg per sqm or cold application of bituminous elastomeric coat at 0.70 Kg/ Sqm Note: Water proofing compound shall be measured and paid separately. Work shall be carried out by experienced applicator after obtaining prior approval.

M&L roof treatment with APP modified water proofing membrane with the following specifications complete all as specified and directed :-

Removing existing roof / chajjas treatment of any type like plastic felt / HP tiles of any description and including taking down existing plastering / concrete of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris to a distance exceeding 50 m but not exceeding 100 m.

Brushing with neat cement slurry @ 3 Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement.

Preparation of plastered surfaces by removing dust, dirt & including applying oil bound bituminous primer at 0.2 Kg per sqm and providing APP modified water proofing membrane weight not less than 4.5 Kg / Sqm reinforced with non oven polyester mat weight not less than 160 grams per sqm including minimum 10 cm side / over lap and including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2 Kg per sqm and on drying applying a coat of solar reflective bituminous aluminium paint at 0.1Kg/sqm. Note: Water proofing compound shall be measured and paid separately. Work shall be carried out by experienced applicator after obtaining prior approval.

M&L 75 mm thick PCC 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base and including and demolition complete all as specified and directed..

M&L 80 mm thick, M-40 Grade machine pressed glass fibre reinforced glossy finished coloured precast concrete interlocking paver block with approved design and pattern as in path/ parking etc., conforming to IS-15658-2006 of any shape, size and color with grey cement and pigment complete all as specified and directed.

M&L spreading and levelling sand cushioning 50 mm thick including watering and consolidation complete all as specified and directed.

M&L coloured and chequered cement concrete tiles 200 mm x 200 mm x 25 mm thick set, jointed and pointed in neat cement slurry with grey pigment cement and pigment as in floors and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in coping and including necessary form work complete all as specified and directed.

M&L point wiring complete with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non metallic rigid PVC conduit medium grade ISI marked incl accessories concealed type wiring incl GI/ MS branded sunken boxes of suitable module concealed on walls including modular frame and cover of suitable module fixed with cadmium plated iron screws for housing modular type switches, switch socket outlets, fan regulators etc., incl provision of 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly for one light point controlled by one switch one way and including taking down existing complete all as specified and directed.

Note: Cost of cutting chases in walls and making good for concealed wiring and cost of modular boxes with cover plates is deemed to be included in quoted rate.

All as per Sl. Item No. 116 above but for one 05 Amp socket outlet on independent board.

All as per Sl. Item No.116 above but for one 05 Amp socket outlet on the same board with other switches.

All as per Sl. Item No. 116 above but wiring with 2.5 Sqmm PVC insulated unsheathed cable copper conductor multi stranded (for 15 Amps power socket) with one run of copper conductor PVC insulated multi-stranded cable 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly.

S&F modular switch 6 Amp, one way, 1 module, 230 volts, ISI marked complete all as specified and as directed.

S&F modular socket 6 Amps 2/3 pin combined multipurpose 2 module, ISI marked complete all as specified and as directed.

S&F modular socket 6/16 Amps 2/3 pin multipurpose 2 module, ISI marked complete all as specified .

S&F modular switch 16 Amps, one way, 1 module, 230volts, ISI marked complete all as specified and as directed.

S&F ceiling rose 3 terminal ISI marked suitable for 230 volts AC supply, complete all as specified and as directed.

S&F in repairs, professional luminaries LED batten type fitting 1x 20 watt indoor aluminium housing LED battens integrated type complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed Make: Havells, Cat No. LUMILINEPLUSNEOBS20W LED830 SPCSSINDS / Philips, Cat No. - BN021 LED225 6500K PSUGR / Crompton, Cat No.-CCS-100-20-65-HL2-DP-NWH.

S&F in repairs, integral LED 35 watts security light fitting comprising of pressure die cast aluminium housing with high power LEDs & electronic driver and including 40 mm dia GI pipe bracket medium grade fixed to pole / wall with flat iron clamps, bolts nuts and washers complete all as specified and as directed . Make: Havells, Cat No. - ENDURASUNDOWNSL35 WLED765 PASYBOPC / Crompton, Cat No.- TRP-417-45-30-SL-LM- NBK. / Philips Cat No.-BRP030 LED 35CWMR PSU GR DX

S&F factory made epoxy powder coated distribution board double door TPN 4 ways (VTPN MCCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with suitable knock outs complete all as specified and directed.

S&F factory made epoxy powder coated distribution board SPN 8 ways double door with acrylic top cover (IP-43 protection) fabricated wih minimum 1.6 mm thick CRCA sheet complete all as specified and directed

S&F MCB SPN 32 amps, 240 V, 10 KA 'C' curve complete all as specified and directed.

S&F MCB TPN 63 to 100 Amps, 415 V, 10 KA 'C' curve complete all as specified and directed.

S&F in repairs MCB SP 10 to 32 Amps, 240 V, ‘C’ series complete all as specified and as directed.

M&L sub main / circuit wiring 2 runs of single core of size 6 Sqmm, PVC FRLS insulated unsheathed multi-stranded copper conductor cables drawn through and including 20 mm dia PVC conduit medium grade with all necessary fittings concealed in walls, ceilings or in floors, provision of one run of 6 sqmm PVC FRLS insulated unshealted multistranded copper conductor single core cable for earth continuity and connected to common earth dolly and taking down complete all as specified and directed.

M&L electrical earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25 m deep below normal GL) with top edge of the earth plate at a depth not less than 1.5 m below normal GL and including connected to GI wire 4 mm dia by means of bolts, nuts, washers made of galvanized iron connected to earthing to body of equipment /DBs, GI wire protected by 15 mm dia light grade GI pipe upto connecting point and watering arrangements with 20 mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No. 3. of MES Schedule (SSR) Part I complete all as specified and directed.

Note : The quoted rate is deemed to be inclusive of the cost of earth work exavation on any type soil and removal of surplus soil to a distance of 50 m, PCC 1:2:4 type B1 for earth pit cover 6 nos. 8 mm dia TMT bars on both direction, earth lead protection GI pipe medium grade with suitable size from earth plate electrode to main switch, GI wire length up to 7.50 m will measured as one unit

M/s S N Atiwadkar (BID ID -3496913)

DHANSHRI ENTERPRISES (BID ID -3497768)

Manak landmarks (BID ID -3505791)