Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹35.1 LAccepted-AOC H NO 1395 SECTOR 21 PANCHKULA 134112 HARYANA | PANCHKULA | HARYANA | 134112 | ₹35.1 L Quoted ₹35.8 L | L1 | Accepted-AOC Being lowest |
| 2 | L2₹36.2 LRejected-Finance VILL BHANDWAR PO CHANDPUR 165 TEHSIL SADAR DISTT BILASPUR HP 174004 | BILASPUR | BILASPUR | HIMACHAL PRADESH | 174004 | ₹36.2 L | L2 | Rejected-Finance Other than L1 |
| Sl No | Description | Qty | Unit | R B TRADERS L1 | H M INFOTECH L2 |
|---|---|---|---|---|---|
| 1.00 | Demolition of cement concrete (un reinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing debris off the premises complete all as specified and/or as directed by Engr-in-Charge. | 41.41 | Cum | 250 ₹10,352.50 | 500 ₹20,705 |
| 2.00 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge. | 240 | Sqm | 20 ₹4,800 | 50 ₹12,000 |
| 3.00 | Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge. | 697 | Sqm | 20 ₹13,940 | 10 ₹6,970 |
| 4.00 | Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge. | 1,640 | RM | 5 ₹8,200 | 2 ₹3,280 |
| 5.00 | Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge. | 13.25 | Cum | 250 ₹3,312.50 | 500 ₹6,625 |
| 6.00 | Taking down cement plaster on brick/PCC block or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge. | 115 | Sqm | 20 ₹2,300 | 50 ₹5,750 |
| 7.00 | Taking down chowkat or frame with shutters (without taking of shutters from the frame) not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge. | 34 | Each | 150 ₹5,100 | 100 ₹3,400 |
| 8.00 | Taking down chowkat or frame with shutters (without taking of shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge. | 9 | Each | 200 ₹1,800 | 100 ₹900 |
| 9.00 | Taking down shutters not exc. 1 Sqm each complete all as directed by Engr-in-Charge. | 4 | Per Leaf | 100 ₹400 | 100 ₹400 |
| 10.00 | Taking down shutters exc. 1 Sqm not exc. 2 Sqm each complete all as directed by Engr-in-Charge. | 6 | Per Leaf | 150 ₹900 | 100 ₹600 |
Updated dates
Tender Value
₹36.2 L
EMD Value
₹72,400
Closing Date
10 Nov 2025, 6:00 pmClosed
CWE, HQ 138 WE
CWE, HQ 138 WE
SPECIAL REPAIR OF BLDG NO TO-654 (JCOs MESS), P-926A (OR COOK HOUSE), P-69/1, P-69/2, P-69/3, P-69/4 AND P-57/3 (TOILET BLOCK) AT VARIOUS UNITS UNDER GE 865 EWS
2025_MES_728867_2
138WE/L-174/2025-26
Open Tender
Civil Works
180 days
GE 865 EWS
AS PER TENDER DOCUMENTS
6 documents required · 6 mandatory
₹500
GE 865 EWS
₹72,400
Yes
8 Jan 2026
15 Oct 2025
17 Nov 2025
15 Oct 2025
10 Nov 2025
22 Oct 2025
Amount
Demolition of cement concrete (un reinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing debris off the premises complete all as specified and/or as directed by Engr-in-Charge.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge.
Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge.
Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge.
Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge.
Taking down cement plaster on brick/PCC block or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge.
Taking down chowkat or frame with shutters (without taking of shutters from the frame) not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.
Taking down chowkat or frame with shutters (without taking of shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.
Taking down shutters not exc. 1 Sqm each complete all as directed by Engr-in-Charge.
Taking down shutters exc. 1 Sqm not exc. 2 Sqm each complete all as directed by Engr-in-Charge.
Hacking out old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and/or directed by Engr-in-Charge.
Dismantling plain or corrugated steel sheeting any gauge or thickness including nanital or similar pattern complete all as specified and as directed by Engr-in-Charge.
Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or directed by Engr-in-Charge.
Dismantling boarding/ wooden flooring of any description, fixed in any position, complete all as specified and/or directed by Engr-in-Charge.
M&L for 2nd class hard wood factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated, including backing with thermocol sheets, over 6 micron polyethylene sheeting over the concrete to minimize moisture migration from the concrete complete all as specified and/or directed by Engr-in-Charge.
M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.
M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling panelling, complete all as specified and as directed.
M&L for 6mm (5 ply) thick veneered decorative (Knoty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work on wall complete all as specified and/or as directed by Engr-in-Charge.
All as per Srl Item No 18 above, but in ceiling.
M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by Engr-in-Charge
M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by Engr-in-Charge.
M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and/or as directed by Engr-in-Charge.
M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20mm graded aggregate) as plinth protection finished even and smooth with out using extra cement, complete all as specified and/or as directed by Engr-in-Charge.
M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and/or as directed by Engr-in-Charge.
M&L for PCC 1:4:8, type D2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.
Demolition of reinforced cement concrete of any description and position not otherwise specifically provided for.
M&L for reinforced cement concrete (Nominal Mix) 1:2:4 type B1 (20mm graded aggregate) as in slabs supported of walls, beams and columns in floors, roofs, landings, balconices, canopies, deck slabs and in shelves etc. complete all as specified and/or as directed by Engr-in-Charge.
M&L for precast cement concrete 1:2:4 type B1 (20mm graded aggregate) in landings, cover slabs (for manholes etc.), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, set in CM 1:6, complete all as specified and/or as directed by Engr-in-Charge.
M&L for form work to soffits of suspended slabs flat type such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or slopping etc. complete all as specified and/or as directed by Engr-in-Charge.
M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bar, complete all as specified and/or as directed by Engr-in-Charge.
M&L precast solid blocks in cement concrete 1:3:6 type C-1 (20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.
M&L for 10mm thick rendering on fair faces of block/ brick wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and/or directed by Engr-in-Charge.
M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 including mixing of liquid water proofing compound as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge. Note : WPC will be measured and paid separately.
M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4, complete all as specified and/or as directed by Engr-in-Charge.
Supply only integral liquid water proofing compound. Make : Pidilite/Sika/Asian paints.
M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of primer complete all as specified and/or as directed by Engr-in-Charge.
M&L for prearing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of wall, complete all as specified and/or as directed by Engr-in-Charge.
M&L for preparation of new plastered wall surface of any description and applying three coats of white wash complete all as specified and/or as directed by Engr-in-Charge.
S&F 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and/or as directed by Engr-in-Charge.
S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and/or as directed by Engr-in-Charge.
S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by the Engr-in-Charge.
M&L for powder coated aluminium door shuttlers, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, hinge type B-21 100 mm longs (3 Nos) suitable handle (2 Nos) (Glass / Wiremesh should be measured seperately) complete all as specified and/or as directed by Engr-in-Charge.
S&F anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 Nos) suitable handle (1 No) etc. complete all as specified and/or as directed by Engr-in-Charge.
S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and/or as directed by Engr-in-Charge.
S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site, complete all as specified and/or as directed by Engr-in-Charge.
S&F 2nd class hard wood 35 mm thick Glazed and Skelton shutter, open and prepared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured separately) complete all as specified and/or as directed by Engr-in-Charge.
M&L for preparation of new untreated wood or wooden based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and/or as directed by Engr-in-Charge.
M&L sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and/or as directed by Engr-in-Charge.
M&L sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and as directed.
S&F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and/or as directed by Engr-in-Charge.
S&F 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and/or as directed by Engr-in-Charge.
S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and/or as directed by Engr-in-Charge.
S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and/or as directed by Engr-in-Charge.
S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and/or as directed by Engr-in-Charge.
S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and/or as directed by Engr-in-Charge.
S&F in repair aluminium (die cast) body door closer hydraulically designation No 3 universal type suitable for door shutter of 851 to1000mm in width and weight 61 to 80 kg complete all as specified and/or as directed by Engr-in-Charge.
S&F floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and/or as directed by Engr-in-Charge.
S&F 75mm long aluminium anodized, butt hinges of extruded section type C-21, complete all as specified and/or as directed by Engr-in-Charge.
S&F 100mm long aluminium anodized, butt hinges of extruded section type B-21, complete all as specified and/or as directed by Engr-in-Charge.
S&F mild steel butt hinges, medium weight cold rolled 100mm size, complete all as specified and/or as directed by Engr-in-Charge.
S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and/or as directed by Engr-in-Charge.
M&L for 25 mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in sub base of floor complete all as specified and/or as directed by Engr-in-Charge.
M&L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exc. 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and/or as directed by Engr-in-Charge.
M&L for Non - skid coloured Ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and/or as directed by Engr-in-Charge.
M&L for 20 mm thick granite stone (any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting etc. and screed bed with CM (1:4) 20mm thick for laying floor tiles complete all as specified and/or as directed by Engr-in-Charge.
M&L for glazed ceramic coloured tiles in vertical surfaces of size 450x350x7mm/ 350x250x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortar (1:4) as in backing coat complete all as specified and/or as directed by Engr-in-Charge.
Dismantling water tank exc. 250 & not exc. 500 litre capacity and removing to store complete all as specified and/or as directed by Engr-in-Charge.
All as per Srl Item No 67 above, but exc. 500 & not exc. 1000 litre capacity.
S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories, complete all as specified and/or as directed by Engr-in-Charge.
All as per Srl Item No 69 above, but of capacity 500 litres.
S&F in repairs 25mm bore stop valve chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and as directed.
S&F in repairs 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/PPR, complete all as specified and as directed.
Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and/or as directed by Engr-in-Charge.
M&L for Cement concrete 1:4:8, type D-2, (using 40mm graded stone aggregate) 75 mm thick as in sub -floors, sub- bases, floors and pavings, etc. complete all as specified and/or as directed by Engr-in-Charge.
M&L for Machine cut Kota stone slab flooring 20-25mm thick over cement screed bed 20mm thick in CM 1:6, set and jointed in neat cement slurry laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and/or as directed by Engr-in-Charge.
M&L for Cheqeured cement concrete tiles (glazed) 30cm X 30cm X 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments, laid over 20mm thick cement screed base (1:6) complete all as specified and/or as directed by Engr-in-Charge.
S&F 0.63mm thick black, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers in roofs, walls etc. with grade of zinc coating 275.
S&F 0.63mm thick plain black mild steel sheeting as in ridges hi, valley gutters drip and straight flashings (length and girth as fixed), complete all as specified and/or as directed by Engr-in-Charge.
M&L for preparation of old steel / CGI sheet surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint, complete all as specified and/or as directed by Engr-in-Charge.
M&L for preparation of new steel / CGI sheet surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc, complete all as specified and/or as directed by Engr-in-Charge.
M&L for preparation of old plastered wall surfaces and applying two coats of cement base paint, complete all as specified and/or as directed by Engr-in-Charge.
M&L for preparation of old treated surfaces of walls and applying two coats of oil bound distemper complete all as specified and directed
S&F MS rolled sections in main and cross beams, hip and jack rafters; purlins where connected to common rafters running rails and guids for sliding doors, fixed with angle cleats or other connecting plates and similar work conforming to Fe-290, Gde-E-165, complete all as specified and/or as directed by Engr-in-Charge.
S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240, complete all as specified and/or as directed by Engr-in-Charge.
M&L for preparation new steel surfaces of any description, not otherwise described, over 10cm width/girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and/or as directed by Engr-in-Charge.
S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by Engr-in-Charge.
S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by Engr-in-Charge.
S&F fibre glass reinforced translucent plain sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and/or directed by Engr-in-Charge.
M&L for preparation of old painted steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and/or directed by Engr-in-Charge.
S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs complete all as specified and/or directed by Engr-in-Charge.
S&F in repair Vitreous China wash basin, white, flat back, size 550 x 400 mm including cutting for and pinning in ends of brackets or erecting stand but exlusive of fixing of supply and waste pipe, complete all as specified and/or as directed by Engr-in-Charge.
Supply only 15 mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and/or as directed by Engr-in-Charge.
S&F soap dish, any type, fixed to plugs with chromium plated brass screws completed all as specified and directed.
Supply only 32mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and/or directed by Engr-in-Charge.
S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.
S&F in repair grating doom 75mm dia of PTMT (min weight 25gms) complete all as specified and/or directed by Engr-in-Charge.
S&F in repairs vitreous China squatting pan or Orissa pattern 580 x 440 mm white with integral foot rest (excluding cistern) with front or back inlet ant pattern as in repairs including bedding with PCC 1:2:4, type B-I (using 20 mm graded crushed stone aggregate) complete all as specified and/or directed by Engr-in-Charge.
Supply only flushing cistern of PVC 10 ltr. cap., white colour, valveless symphonic action type, low level, with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/ gel gasket etc as recommended by manufacturer for fixing, packing, complete all as specified and/or directed by Engr-in-Charge.
S&F in repairs 750mm long, 32/40 mm dia, PVC flexible waste pipe for sinks/ wash hand basins.
S&F in repair Toilet paper holder of brass, chromium plated or stainless steel, complete all as specified and/or directed by Engr-in-Charge.
S&F in repair Health faucet (ABS Body) mild steel, chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and/or directed by Engr-in-Charge.
S&F in repair Vitreous China wash down water closet (Pedestal), white (EWC) excluding fixing bolts, flushing cistern and flush pipe, including plastic water closet seat, black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including connection to drain pipe and to flushing pipe antisyphonage pipe etc., complete all as specified and/or directed by Engr-in-Charge. Make : CERA/JAQUAR/KOHLER or equivalent.
S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and/or directed by Engr-in-Charge.
S&F in repairs towel rail 600mm long chromium plated (minimum weight 190 gms), complete all as specified and/or directed by Engr-in-Charge.
Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and/or directed by Engr-in-Charge.
M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water drainage pipes laid in trenches and jointed all as specified.
S&F in PVC (HDPE) SWR 75 mm bore, single socketed in any length with rubber ring joints using solvent as per manufacture instruction, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.
S&F 75 mm dia PVC (SWR) bend any radius, complete all as specified and as directed.
S&F 110 mm dia PVC (SWR) bend any radius, complete all as specified and as directed.
M&L for PCC 1:4:8, type D-2 (using 40mm graded stone aggerate) as in bed to drain pipe incl packing under and haunching against side after they are laid and tested up to 110mm dia pipe, complete all as specified and/or directed by Engr-in-Charge.
Taking up or down 25 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and/or directed by Engr-in-Charge.
Taking up or down 32 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and/or directed by Engr-in-Charge.
S&F 25mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engr-in-Charge.
S&F 32mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engr-in-Charge.
S&F in repairs fancy type 15 mm bore chromium plated bib taps, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.
S&F 15mm bore, PVC connection pipe 600 mm long with PTMT nuts at both ends, complete all as specified and as directed.
Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as specified and directed by Engr-in-Charge.
Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5 sqmm copper conductor cable as continuous earth lead complete all as specified and/or directed by Engr-in-Charge for the followings:-
One light/exhaust fan point controlled by one way switch.
One switch socket outlet 6 Amps, 230 volts point on same board.
One switch socket outlet 6 Amps, 230 volts point on independent board.
All as per Srl item No 120 above, but using cables 4 Sq mm size.
S&F switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and/or directed by Engr-in-Charge.
S&F socket outlet two in one 3 pin, 6 Amps flush type.230 volts complete all as specified and/or directed by Engr-in-Charge.
S&F switch socket combination 2 in 1, 3/5 pin, 6 Amps flush type 230 Volts complete all as directed.
S&F switch Socket combination outlet multi purpose 3/5 pin, 6 Amps and 16 Amps 230 volts complete all as specified and/or directed by Engr-in-Charge.
S&F ceiling rose, surface Bakelite three terminals complete all as specified and/or directed by Engr-in-Charge.
S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 Ways complete all as specified and/or directed by Engr-in-Charge.
S&F MCB SPN 63 Amp 240 Volts, 10 KA, C Curve, AC ISI marked complete all as specified and/or directed by Engr-in-Charge.
S&F MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and/or directed by Engr-in-Charge.
Taking down old unserviceable exhaust fan and supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, complete all as specified and/or directed by Engr-in-Charge. Note : Old unsv fan shall be deposited to MES E/M store.
S&F in replacement LED light fitting 1x20W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and/or directed by Engr-in-Charge. Make : Havells /Crompton / Bajaj or equivalent.
S&F in replacement Air Circular fan, steel body AC single Phase 230V of size 300 mm sweep with blades, frame and louvers, complete all as specified and/or directed by Engr-in-Charge. Note : Old retrieved fans to be deposited with MES store yard.
M&L for submain wiring along with earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping wire size 2x6 sqmm + 1x6 sqmm earth wire complete all as specified and/or directed by Engr-in-Charge.
S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 08 ways complete all as specified and directed.
S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used triple pole and neutral 415 Volts 04 ways all as specified and directed by Engr-in-Charge.
S&F of sheet metal enlcosure with 20 Amp 240 V socket plug top and MCBs single pole and neutral enclosure with two pin and earth plug and socket with one single pole 20 Amp MCB, complete all as specified and/or directed by Engr-in-Charge.
Supply, install, testing complete water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipes etc. including taking down the existing one complete all as specified and/or directed by Engr-in-Charge. Note : Old unsv water heaters retrieved from site shall be deposted with MES store yard.
Supply and laying in trenches or passing through pipe or fixed on surface XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade of size 25 sqmm 2.0 core including taking down old unserviceable cable, complete all as specified and/or directed by Engr-in-Charge.
Supply, laying and testing cable XLPE in replacement insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts, graded with standard aluminium conductor of size 25.0 sqmm 4 core, including taking down old unserviceable cable, complete all as specified and/or as directed by Engr-in-Charge.
M&L for submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping wire size 2x2.5sqmm + 1x2.5 sqmm earth wire including taking down old unserviceable wires, complete all as specified and/or as directed by Engr-in-Charge.
S&F in replacement LED luminaire 600 mm x 600 mm, 35 / 36 Watt, 220V, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver 3 core flexible copper conductor cable of suitable size, complete all as specified and/or as directed by Engr-in-Charge. Make : Havells / Philips / Crompton / Bajaj or equivalent.
S&F in replacement, connecting and testing LED security light fitting 35 Watt, 230 V, AC outdoor type with high pressure die cast aluminium housing, heat resistant toughened glass cover, LED driver, lamp and bracket, impact and corrossion resistant including thermal management in multiple optics with IP 65/66 protection, complete all as specified and/or as directed by Engr-in-Charge.
S&F in replacement of bus bar chamber size 600 mm x 450 mm x 300 mm outdoor type made out of MS sheet 2.0 mm thick mounted on angle iron frame duly painted with two coats of synthetic enamel paint over a coat of primer and comprising of three phase aluminium bus bar 200 Amps mounted on insulators including provisioning of foundation etc. as per manufacturer's instructions complete all as specified and/or as directed by Engr-in-Charge.
Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 m in depth and getting it out for laying of cable / pole in hard / dense soil complete all as specified and/or as directed by Engr-in-Charge.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25cm of soil, complete all as specified and/or as directed by Engr-in-Charge.
Removing excavated material not exc. 50m and depositing where directed at a level exc. 1.5cm above the starting point, complete all as specified and/or as directed by Engr-in-Charge.
M&L for Sand cushioning to under ground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Part-I, 2009. Note : Punned thickness only will be measured and paid.
Supply and laying factory made, machine pressed, unreinforced, pre-cast concrete cable cover class LV type-1 flat size 250 x 150 x 40mm, complete all as specified and/or as directed by Engr-in-Charge.
M&L for Earthing complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia GI wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate No 3 of MES SSR Part I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS frame and cover 6 mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with wire mesh, GI watering pipe 20mm dia medium grade and lugs complete all as specified and/or as directed by Engr-in-Charge.
H M INFOTECH (BID ID -3458650)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.33 MB
TenderL17425262call.pdf
Tender Documents • 1.19 MB
BOQ_823283.xls
BOQ • 0.62 MB
Download all tender documents and submit your bid