Establishment of Certification Laboratory for Organically Naturally Grown Product in Bundelkhand region at RLBCAU Jhansi UP

ABSTRACT OF COST

DSR Amount Market Amount

SL.NO. PARTICULARS DSR + MR (Rs.)

TOTAL (DSR + MR) 255,35,982.09

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU, Jhansi

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

B 2.00 EARTH WORKS

1 1.1.2.1 Disposal of earth by Mechanical Transport including loading,unloading and stacking 0 to

2 2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means

over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)

including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m,

as directed by Engineer-in-charge.

3 2.10 Excavating trenches of required width for pipes, cables, etc. including excavation for

sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m including getting

out the excavated soil, and then returning the soil as required, in layers not exc

a 2.10.1 All kinds of soil. 0.00 0.00

i 2.10.1.2 Pipes, cables, etc. exceeding 80mm dia but not exceeding 300mm dia. Metre 80.00 352.15 342.64 27,411.36

4 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations

etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by Cum 85.79 196.00 190.71 16,360.07

ramming and watering, lead up to 50 m and lift upto 1.5 m.

5 2.27 Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete.

6 2.28 Surface dressing of the ground including removing vegetation and inequalities not

exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. 0.00 0.00

7 2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and

saplings of girth up to 30 cm measured at a height of 1 m above ground level and

removal of rubbish up to a distance of 50m outside the periphery of the area cleared.

8 2.34 Supplying chemical emulsion in sealed containers including delivery as specified

i 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Litre 110.40 234.75 228.41 25,216.66

9 2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite

treatment (excluding the cost of chemical emulsion) :

i 2.35.1.1 Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres

/ sqm of the vertical surface of the substructure to a depth of 300mm including

excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane

E.C. 20% with 1% concentration

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

a) 2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300

mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 0.00 0.00

(1 cement : 2 Coarse sand) to match the existing floor:

i 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration Sqm 552.00 310.05 301.68 1,66,526.61

TOTAL (Carried Over to Summary of Civil Works) 3,41,977.04

C 4.00 CONCRETE WORKS

1 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level :

b 4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone

aggregate 40 mm nominal size derived from natural sources)

2 4.11 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1

cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone Sqm 41.16 495.75 482.36 19,854.90

aggregate 20mm nominal size derived from natural sources).

3 4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand

(zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry

brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine Sqm 70.00 749.30 729.07 51,034.82

sand, including necessary excavation, levelling & dressing & finishing the top smooth.

TOTAL (Carried Over to Summary of Civil Works) 4,06,166.06

D 5.00 REINFORCED CEMENT CONCRETE WORK

1 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

a 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. Sqm 40.32 392.15 381.56 15,384.58

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform. Sqm 546.00 927.25 902.21 4,92,608.98

e 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 216.00 736.40 716.52 1,54,767.72

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 360.00 961.30 935.34 3,36,724.16

g 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 30.00 764.95 744.30 22,328.89

j 5.9.16 Edges of slabs and breaks in floors and walls 0.00 0.00

2 5.11.1 Extra for additional height in centering, shuttering where ever required with adequate

bracing, propping etc., including cost of de-shuttering and decentering at all levels, over

a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be Sqm 280.00 384.30 373.92 1,04,698.69

measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be

3 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete upto plinth level.

i 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 17340.46 107.85 104.94 18,19,673.70

4 5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete above plinth level.

i 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 26010.68 107.85 104.94 27,29,510.55

5 5.30 Add for plaster drip course / groove in plastered surface or moulding to R.C.C.

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

6 5.33.1 Providing and laying in position ready mixed or site batched design mix cement concrete

for reinforced cement concrete work; using coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and workability without impairing strength; including

pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost

of centering, shuttering, finishing and reinforcement as per direction of the engineer-in- 0.00 0.00

charge; for the following grades of concrete. Note: Extra cement up to 10% of the

minimum specified cement content in design mix shall be payable separately. In case the

cement content in design mix is more than 110% of the specified minimum cement

content, the contractor shall have discretion to either re-design the mix or bear the cost

of extra cement.

a) 5.33.1 All works upto plinth level. 0.00 0.00

i 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 78.00 9504.75 9248.12 7,21,353.50

b) 5.33.2 All works above plinth level upto floor V level. 0.00 0.00

i 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 169.00 9860.40 9594.17 16,21,414.59

7 5.35 Add for using extra cement in the items of design mix over and above the specified

cement content therein.

TOTAL (Carried Over to Summary of Civil Works) 80,54,787.45

E 6.00 BRICK WORK

1 6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

in foundation and plinth in:

i 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 48.00 7132.25 6939.68 3,33,104.60

2 6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

in super structure above plinth level up to floor V level in all shapes ans sizes in: 0.00 0.00

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 190.00 9105.95 8860.09 16,83,416.98

3 6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level upto floor V level. 0.00 0.00

6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) Sqm 178.00 1150.50 1119.44 1,99,259.70

4 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry. Sqm 178.00 104.80 101.97 18,150.73

TOTAL (Carried Over to Summary of Civil Works) 22,33,932.01

F 8.00 MARBLE & GRANITE WORK

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

1 8.2 Providing and fixing 18mm thick gang saw cut ( premoulded and prepolished) machine

cut for kitchen platforms, vanity counters, window sills , facias and similar locations of

required size of approved shade, colour and texture laid over 20mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with

matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to

edge to give high gloss finish etc. complete at all levels.

b) 8.2.2 Granite of any colour and shade

2 8.3 Providing edge moulding to18 mm thick marble stone counters, Vanities etc.,including

machine polishing to edge to give high gloss finish etc. complete as per design approved 0.00 0.00

by Engineer-in-Charge.

3 8.4 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia

and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. Metre 25.00 568.55 553.20 13,829.98

4 8.5 Extra for providing opening of required size & shape for wash basin / kitchen sink in

kitchen platform, vanity counter and similar location

inmarble/Granite/stonework,including necessary holes for pillar taps etc.including Each 8.00 978.70 952.28 7,618.20

moulding, rubbing and polishing of cut edges etc.complete.

5 8.10 Providing and fixing stone slab with table rubbed, edges rounded and polished, of

size75x50cm deepand 1.8cm thick, fixed in urinal partitions by cutting a chase of

appropriate width with chase cutter and embedd in gthe stone in the chase with epoxy

grout or with cement concrete 1:2:4 (1cement: 2coarsesand: 4 graded stone aggregate

6mm nominal size)as per direction of Engineer-in-charge and finished smooth.

6 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours, shades

except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in

skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement Sqm 48.00 1267.95 1233.72 59,218.34

: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing

in white cement mixed with pigment of matching shade complete.

TOTAL (Carried Over to Summary of Civil Works) 4,09,329.22

G 9.00 WOOD, WPC & uPVC WORK

1 9.53 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block

300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 Each 10.00 228.85 222.67 2,226.71

mm nominal size)

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

2 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary

screws, etc. complete. Each 18.00 121.65 118.37 2,130.58

3 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic

door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight

upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed Each 18.00 983.15 956.60 17,218.89

adjustment with necessary accessories

and screws etc. complete.

4 9.96 Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less

than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts 0.00 0.00

and screws etc. complete :

5 9.97 Providing and fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than

grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and 0.00 0.00

screws etc. complete-

6 9.100 Providing and fixing aluminium handles ISI marked anodised ( anodic coating not less than

grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and 0.00 0.00

screws etc. complete-

7 9.101.2 Providing and fixing aluminium hanging floor door stopper, l5l marked, anodised (anodic

coatinS not less than grade AC 10 as per 15 : 1868) transparent or dyed to required

colour and shade, with necessary screws etc. complete. Twin rubber stopper

8 9.135 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and

clerestory windows using wire gauge with average width of aperture 1.4 mm in both 0.00 0.00

directions with wire of dia. 0.50 mm all complete.

8.2 9.135.2 With 12 mm mild steel U beading Sqm 22.00 1228.00 1194.84 26,286.57

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

7 26.86 Providing and fixing factory made single extruded WPC (Wood Polymer Composite)

solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin

PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural

fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity

index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement

and screwed with full body threaded star headed SS screws having minimum frame

density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),

minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and

resistance to spread of flame of Class A category with property of being termite/borer 0.00 0.00

proof, water/moisture proof and fire retardant and fixed in position with M.S hold

fast/lugs/SS dash fasteners of required dia and length complete as per direction of

Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for

separately).Note: For WPC solid door/window frames, minus 5mm tolerance in

dimensions i.e depth and width of profile shall be acceptable. Variation in profile

dimensions on plus side shall be acceptable but no extra payment on this account shall

8 26.87 Providing and fixing factory made single extruded WPC (Wood Polymer Composite)

solid plain flush door shutter of required size comprising of virgin polymer of K value 58-

60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice

husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)

having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face)

& 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850

N/mm2 and resistance to spread of flame of Class A category with property of being

termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel

butt hinges of required size with necessary full body threaded star headed counter sunk

S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges

and necessary S.S screws shall be paid separately)

TOTAL (Carried Over to Summary of Civil Works) 3,56,651.09

H 10.00 STEEL WORK

1 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses

etc., including cutting, hoisting, fixing in position and applying a priming coat of approved

steel primer, including welding and bolted with special shaped washers etc. complete.

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

2 10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp,

of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top

surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet

box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall

be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

3 10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener

of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head,

comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame 0.00 0.00

, concrete/ masonry, etc. as per direction of Engineer-in-charge.

4 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes, channels, plates etc., including welding, grinding, buffing, polishing

and making curvature (wherever required) and fitting the same with

necessary stainless steel nuts and bolts complete, i/c fixing the railing

with necessary accessories & stainless steel dash fasteners , stainless

steel bolts etc., of required size, on the top of the floor or the side of waist

slab with suitable arrangement as per approval of Engineer-in-charge,

(for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners

TOTAL (Carried Over to Summary of Civil Works) 7,36,322.42

I 11.00 FLOORING WORK

1 11.5 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50

mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate

20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1

cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, Sqm 210.00 1,056.15 1027.63 2,15,803.13

hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s

specifications. This includes cost of cement slurry, but excluding the cost of nosing of

steps etc. complete.

2 DSR-(2021) Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by

11.41A the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement

mortar 1:4 (1 cement:

4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints

with white cement and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles

2.01 11.41A.2.1 Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 600 mm Sqm 262.32 1,502.75 1462.18 3,83,557.94

2.02 11.41A.3.1 Glazed Vitrified tiles MatUAntiskid finish of size Size of Tile 600 x 600 mm Sqm 22.77 1,464.85 1425.30 32,459.76

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

2.00 16.68 Providing and laying 60mm thick factory made cement concrete interlocking paver block

of M -30 grade made by block making machine with strong vibratory compaction and of

approved size and design/ shape laid in required colour and pattern over and including

50mm thick compacted bed of course sand, filling the joints with fine sand etc. all Sqm 22.77 972.00 945.76 21,538.65

complete as per the direction of Engineer-in-charge.

TOTAL (Carried Over to Summary of Civil Works) 6,53,359.48

J 12.00 ROOFING

1 12.1 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with

polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet

washers or with G.I. limpet washers filled with white lead, including a coat of approved

steel primer and two coats of approved paint on overlapping of sheets complete (up to

any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters

and trusses and including cutting to size and shape wherever required.

12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m* Sqm 42.00 1457.15 1417.81 59,547.89

2 12.21 Providing and laying gola 75x75mm in cement concrete M15 grade including finishing

with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design in 75x75 mm rmt. 70.00 305.15 296.91 20,783.77

3 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over

P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : Each 28.00 298.25 290.20 8,125.52

3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing

the outlet complete.

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

4 12.45 Providing and fixing false ceiling at all heights including providing and

fixing of frame work made of special sections, power pressed from M.S.

sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm

wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre

to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia

x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required

size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre

to centre, shall be fixed in a direction perpendicular to G.I. intermediate

channel with connecting clips made out of2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm thick

27 mm high having flanges of 20 mm and 30 mm long, the perimeter of

ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre,

with 25 mm long dry wall screws@ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of

dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed,

all complete as per drawings, specification and direction of the Engineer

in Charge but excluding the cost of painting with :

12.45.3 12.5 mm thick tapered edge gypsum moisture resistant

5 12.52 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true

horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel

sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T"

runner with suitably spaced joints to get required length and of size 24x38 mm made

from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T"

of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced 0.00 0.00

between main "T" at 600 mm center to center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick

(minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of

600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of

12.52.3 approved

12.5 mm texture in theedge

thick square grid including, required

PVC Laminated cutting/making,

Gypsum opening for services like

595x595 mm, made of Gypsum plasterboard, manufactured from

natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire

retardant PVC film on the face side and 12micron metalized polyester on the back side

with all edges sealed with the face side PVC film which goes around and wraps the

edges and is bonded to the edges and the back side m

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

6 26.22 Providing and fixing false ceiling at all heights with integral densified calcium silicate

reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved

texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50

(minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible

as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7),

humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM

518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped

galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including

both sides) comprising of main- T runners of size 24x38 mm of length 3000 mm, cross -

T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size

24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from 0.00 0.00

ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm

long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto

1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron

perimeter wall angle of size

24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help

of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws.

The work shall be carried out as per specifications, drawing and as per directions of the

Engineer-in-Charge.

26.22.1 With 15 mm thick tegular edged light weight calcium

silicate false ceiling tiles.

TOTAL (Carried Over to Summary of Civil Works) 10,26,185.72

K 13.00 FINISHING WORK

1 13.4 12 mm cement plaster of mix :

2 13.11 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1

cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 Sqm 526.92 518.55 504.55 2,65,857.41

cement : 6 fine sand).

3 13.16 6 mm cement plaster of mix : 0.00 0.00

4 13.21 Extra for providing and mixing water proofing material in plaster work in proportion per bag

recommended by the manufacturers. of 50kg

5 13.41 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less

than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : 0.00 0.00

New work (two or more coats) over and including water thinnable priming coat with

cement primer having VOC content less than 50 gram/litre

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of

required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat

of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required

colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint

of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of

8 13.80 approved brand and manufacturer, over the plastered wall surface to prepare the surface Sqm 2036.37 156.05 151.84 3,09,195.77

even and smooth complete

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre of approved brand and

manufacture, including applying additional coats wherever required to achieve even

shade and colour. Two coats

TOTAL (Carried Over to Summary of Civil Works) 14,61,007.30

L 21.00 ALUMINIUM WORK

1 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with

extruded built up standard tubular sections/appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or

with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at

junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium

sections shall be smooth, rust free, straight, mitred and jointed echanically wherever

required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass

/ stainless steel screws, all complete as per architectural drawings and the directions of

Engineer-in-charge. Glazing and paneling to be paid for separately) :

a) 21.1.1 For fixed portion.

i 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) KG 320.00 530.90 516.57 1,65,301.02

b 21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots

and making provision for fixing of fittings wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings shall be

paid for separately)

1 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) KG 186.00 634.45 617.32 1,14,821.49

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

2 21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions

etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings

and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid

in basic item):

i 21.3.2 With float glass panes of 5.5 mm thickness (weight not less than 12.50 kg/sqm) Sqm 10.00 1505.25 1464.61 14,646.08

3 21.2 Providing and fixing 12 mm thick prelaminated particle board flat pressed

three layer or graded wood particle board conforming to IS: 12823 Grade

l Type ll, in panelling fixed in aluminum doors, windows shutters and 0.00 0.00

partition frames with C.P. brass / stainless steel screws etc. complete as

per architectural drawings and directions of engineer-in-charge.

21.2.2 Pre-laminated particle board with decorative lamination on

TOTAL (Carried Over to Summary of Civil Works) 2,99,109.74

M 22.00 WATER PROOFING

1 22.7 Providing & laying integral cement based water proofing treatment including preparation

of surface as required for treatment of roofs, balconies, terraces etc consisting of

following operations: a) Applying a slurry coat of neat cement using 2.75kg/sqm of

cement admixed with water proofing compound confirming to IS. 2645 and approved by

Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height

including cleaning the surface before treatment. b) Laying brick bats with mortar using

broken bricks/brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement

: 5 coarse sand ) admixed with water proofing compound confirming to IS : 2645 and

approved by Engineer-in-charge over 20 mm thick layer of cement of 1:5 ( 1 cement : 5

coarse sand ) admixed with water proofing compound confirming to IS : 2645 and

approved by Engineer-in-charge to required slope and treating similarly the

adjoining walls upto 300mm height including rounding of junctions of walls and slabs. c)

After two days of proper curing applying a second coat of cement slurry using

2.75kg/sqm of cement admixed with water proofing compound confirming to IS : 2645

and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless

cement mortar 1:4 (1 cement : 4 coarse sand ) admixed with water proofing compound

confirming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre

cloth of approved quality in top layer and finally finishing the surface with trowel with neat

cement slurry and making pattern of 300x300 mm square 3mm deep. e) The whole

terrace so finished shall be flooded with water for a minimum period of two weeks for

curing and for final test. All above operations to be done in order and as directed and

specified by the Engineer-in-charge:

i 22.7.1 With average thickness of 120mm and minimum thickness at khurra as 65mm. SQM 180.00 1684.60 1639.12 2,95,040.84

TOTAL (Carried Over to Summary of Civil Works) 2,95,040.84

ALL SUB-HEAD TOTAL 162,73,868.37

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE AMOUNT

DSR 2020 HORTICULTURE WORKS

1 2.35 Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of

existing ground prepared with proper level and ramming with required tools wooden and

than rolling the surface with light roller make the surface smoothen and light watering the

same maintenance for 30 days or more till the grass establish properly,as per direction of

officer in charge

adjoining walls upto 300mm height including rounding of junctions of walls and slabs. c)

After two days of proper curing applying a second coat of cement slurry using

2.75kg/sqm of cement admixed with water proofing compound confirming to IS : 2645

and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless

cement mortar 1:4 (1 cement : 4 coarse sand ) admixed with water proofing compound

confirming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre

cloth of approved quality in top layer and finally finishing the surface with trowel with neat SQM 1440.00 87.50 1,26,000.00

cement slurry and making pattern of 300x300 mm square 3mm deep. e) The whole

terrace so finished shall be flooded with water for a minimum period of two weeks for

curing and for final test. All above operations to be done in order and as directed and

specified by the Engineer-in-charge:

TOTAL (Carried Over to Summary of Civil Works) 1,26,000.00

GST Factor 1.0633

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally

Grown Product in Budelkhand Region at RLBCAU, Jhansi

1 SANITARY INSTALLATION 1,25,043.29

2 WATER SUPPLY 7,52,050.19

3 INTERNAL DRAINAGE 3,64,078.70

4 RAIN WATER WORK 1,13,158.83

5 EXTERNAL WATER SUPPLY WORK 1,08,697.24

6 EXTERNAL SEWER WORK 2,70,876.88

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

A) SANITARY INSTALLATION

1 17.2 Providing and fixing white vitreous china pedestal type water

closet (European type W.C. pan) with seat and lid, 10 litre low

level white P.V.C. flushing cistern, including flush pipe, with

manually controlled device (handle lever), conforming to IS :

7231, with all fittings and fixtures complete, including cutting

and making good the walls and floors wherever required.

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 5 6515.55 6339.63 31,698.15

2 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm

C.P. brass pillar taps, 32 mm C.P. brass waste of standard

pattern, including painting of fittings and brackets, cutting and 0.00 0.00

making good the walls wherever require :

17.7.4 White Vitreous China Flat back wash basin size 550x400 mm

with single 15 mm C.P. brass pillar tap

3 17.10.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen

sink as per IS:13983 with C.I. brackets and stainless steel plug

40 mm, including painting of fittings and brackets, cutting and 0.00 0.00

making good the walls wherever required : Kitchen sink

with drain board

4 17.16a Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube Each 5 349.15

upto 1meter long with S.S. Triangular plate to european type

W.C. Of approved quality and make as approved by engineer 339.72 1,698.61

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

5 17.22A Providing and fixing CP Brass 32mm size bottle trap of Each 5 1034.80

approved quality & make and as per the direction of engineer 1006.86 5,034.30

6 17.30 Providing and fixing in position 25 mm diameter mosquito Each 5 55.65

proof coupling of approved municipal design. 54.15 270.74

7 17.31 Providing and fixing 600x450 mm beveled edge mirror of Each 5 1607.95

superior glass (of approved quality) complete with 6 mm thick

hard board ground fixed to wooden cleats with C.P. brass 1564.54 7,822.68

screws and washers complete.

7 17.34 Providing and fixing toilet paper holder : 0.00 0.00

8 17.71 Providing and fixing PTMT liquid soap container 109 mm wide, Each 5 168.35

125 mm high and 112 mm distance from wall of standard

shape with bracket of the same materials with snap fittings of 163.80 819.02

approved quality and colour, weighing not less than 105 gms.

9 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 Each 5 231.95

mm long, 200 mm wide with minimum distances of 37 mm

from wall face with concealed fittings arrangement of approved 225.69 1,128.44

quality and colour, weighing not less than 88 gms.

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

17.73.2 Providing and fixing PTMT towel rail complete with brackets Each 5 708.95

fixed to wooden cleats with CP brass screws with concealed

fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width78 689.81 3,449.04

mm and effective height of 88 mm, weighing not lessthan 190

10 18.21.2.1 Providing and fixing uplasticised PVC connection pipe with Each 10 97.75

brass unions : 45 cm length , 15 mm nominal bore

11 18.49 Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931 : 0.00 0.00

12 18.51 Providing and fixing C.P. brass long body bib cock of

approved quality conforming to IS standards and weighing not 0.00 0.00

less than 690 gms.

18.52.1 Providing and fixing C.P. brass stop cock (concealed) of Each 10 670.45

standard design and of approved make conforming to 652.35 6,523.48

IS:8931.15 mm diameter

13 18.53 Providing and fixing C.P. brass angle valve for basin mixer

14 18.58.1.1 Providing and fixing PTMT grating of approved quality and

Circular type100 mm nominal dia

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

B) WATER SUPPLY

1 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing the

pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the

cost of cutting chases and making good the same including

testing of joints complete as per direction of Engineer in

Concealed work, including cutting chases and making

good the walls etc.

2 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, including

fixing the pipe with clamps at 1.00 m spacing. This includes 0.00 0.00

jointing of pipes & fittings with one step CPVC solvent cement

and testing of joints complete as per direction of Engineer in

Internal work - Exposed on wall 0.00 0.00

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

18.62 Providing and fixing PTMT Ball cock of approved quality,

colour and make complete with Epoxy coated aluminium rod 0.00 0.00

with L.P./ H.P.H.D. plastic ball.

a) 18.62.3 25 mm nominal bore, 152mm long, weighing not less than 440 Each 10 523.80

18.65 Providing and fixing PTMT soap Dish Holder having length of Each 10 111.45

138mm,breadth 102mm, height of 75mm with concealed fitting 108.44 1,084.41

arrangements, weighing not less than 106 gms.

C) INTERNAL DRAINAGE

3 17.35 Providing and fixing soil, waste and vent pipes

17.35.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated Mtr 180 1169.30

inside & outside IS:15905

4 17.36 Providing and filling the joints with spun yarn cement slurry

and cement mortar 1:2 (1 cement: 2 fine sand) in S.C. I I C. I 0.00 0.00

5 17.37 Providing and fixing M.S. holder-bat clamps of approved

design to Sand Cast iron/cast iron (spun) pipe embedded in

and including cement concrete blocks 10x10x10 cm of 1:2:4

mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size), including cost of cutting holes and making

good the walls etc. :

6 17.38 Providing and fixing bend of required degree with access door,

insertion rubber washer 3 mm thick, bolts and nuts

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

17.38.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated Each 10 567.20

inside & outside IS:15905 551.89 5,518.86

7 17.39 Providing and fixing plain bend of required degree. 0.00 0.00

17.39.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated Each 10 368.00

inside & outside IS:15905

8 17.40 Providing and fixing heel rest sanitary bend: 0.00 0.00

17.40.1.2 Sand cast iron S&S as per IS:3989 Each 10 548.70 533.89 5,338.85

9 17.43 Providing and fixing single equal plain junction of required

degree with access door, insertion rubber washer 3 mm thick, 0.00 0.00

bolts and nuts complete.

a) 17.43.1.2 100x100x100 mm Sand cast iron S&S as per IS - 3989 Each 6 925.70 900.71 5,404.24

10 17.44 Providing and fixing single equal plain junction of required

17.44.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & Each 6 581.45

outside as per IS:15905

10 17.55 Providing and fixing door piece, insertion rubber washer 3mm

thick, bolts & nuts complete :

a) 17.55.1.2 100 mm Sand cast iron S&S as per IS - 3989 Each 3 683.85 665.39 1,996.16

11 17.56 Providing and fixing terminal guard. 0.00 0.00

17.56.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & Each 5 427.80

outside as per IS:15905

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

12 17.58 Providing lead caulked joints to sand cast iron/centrifugally

cast (spun) iron pipes and fittings of diameter : 0.00 0.00

13 17.60 Providing and fixing trap of self cleansing design with screwed

down or hinged grating with or without vent arm complete,

including cost of cutting and making good the walls and floors :

a) 17.60.1.3 100 mm inlet and 100 mm outlet Hubless centrifugally cast Each 5 854.55

(spun) iron epoxy coated inside & outside as per IS:15905 831.48 4,157.39

a) 17.60.2.3 100 mm inlet and 75 mm outlet Hubless centrifugally cast Each 5 591.40

(spun) iron epoxy coated inside & outside as per IS:15905

D) RAIN WATER WORK

14 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain

water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

15 12.42 Providing and fixing on wall face unplasticised - PVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A including jointing with 0.00 0.00

seal ring conforming to IS : 5382 leaving 10 mm gap for

thermal expansion.

a) 12.42.2 Single Push fit coupler 0.00 0.00

b) 12.42.3 Single Tee with door 0.00 0.00

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

16 12.44 Providing and fixing to the inlet mouth of rain water pipe cast Each 15 54.70

iron grating 15 cm diameter and weighing not less than 440 53.22 798.35

17 12.43 Providing and fixing unplasticised -PVC pipe clips of approved

design to unplasticised - PVC rain water pipes by means of

50x50x50 mm hard wood plugs, screwed with M.S. screws of

required length, including cutting brick work and fixing in 0.00 0.00

cement mortar 1:4 (1 cement : 4 coarse sand) and making

good the wall etc. complete.

18 12.22 Making khurras 45x45 cm with average minimum thickness of Each 15 298.25

5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over P.V.C.

sheet 1 m x1 m x 400 micron, finished with 12 mm cement 290.20 4,352.96

plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the

outlet complete.

19.6 Providing and laying non-pressure NP2 class (light duty)

R.C.C. pipes with collars jointed with stiff mixture of cement

mortar in the proportion of 1:2 (1 cement : 2 fine sand)

including testing of joints etc. complete :

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

E) EXTERNAL WATER SUPPLY WORK

19 18.12 Providing and fixing G.I. pipes complete with G.I. fittings

including trenching and refilling etc.

F) EXTERNAL SEWER WORK

20 2.10 Excavating trenches of required width for pipes, cables, etc

including excavation for sockets, anddressing of sides,

ramming of bottoms, depth up to 1.5 m, including getting out

the excavated soil, and then returning the soil as required, in

layers not exceeding 20 cm in depth, including

consolidatingeach deposited layer by ramming, watering, etc.

and disposing of surplus excavated soil as directed,within a

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 metre 27 352.15

21 19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 Each 5 2707.65

complete with C.I. grating brick masonry chamber with water

tight C.I. cover with frame of 300x300 mm size (inside) the

weight of cover to be not less than 4.50 kg and frame to be not

less than 2.70 kg as per standard design: 100x100 mm size P

type. With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

22 19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1

cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size), foundation concrete 1:4:8 mix (1 cement : 4

coarse sand : 8 graded stone aggregate 40 mm nominal size),

inside plastering 12 mm thick with cement mortar 1:3 (1 0.00 0.00

cement : 3 coarse sand) finished with floating coat of neat

cement and making channels in cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) finished with a floating coat of neat cement

complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with

frame (light duty) 455x610 mm internal dimensions,total

weight of cover and frame to be not less than 38 kg (weight of 0.00 0.00

cover 23 kg and weight of frame 15 kg) :

19.7.1.1 With common burnt clay F.P.S.(non modular) bricks of class Each 8 12770.55

designation 7.5 12425.75 99,405.96

23 19.8 Extra for depth for manholes: 0.00 0.00

19.8.1.1 With common burnt clay F.P.S.(non modular) bricks of class Mtr 12 8825.40

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

24 19.9 Constructing Brick Masonry circular type manhole 0.91 m

internal dia at bottom and 0.56m dia at top with FPS bricks

class designation 75 in cement mortar 1:4 (1 cement : 4

Coarse sand), inside cement plaster 12mm thick with cement

mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating

coat of of neat cement, foundation concrete 1:3:6 mix ( 1

cement : 3 coarse sand : 6 graded stone aggregate 40mm

nominal size) and making necessary channel in Cement

Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone

Aggregate 20mm nominal size) finished with a floating coat of

neat cement complete as per standard design.

19.9.1 0.91m deep with SFRC cover and frame (heavy duty HD-20

grade designation) 560mm internal diameter conforming to

I.S:12592, total weight of cover and frame to be not less than

182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse

sand: 4 graded stone aggregate 20mm nominal size) including 0.00 0.00

centering, shuttering all complete.(Excavation foot rests and

12mm thick cement plaster at the external surface shall be

paid for separately)

19.9.1.1 with common burnt clay F.P.S.(non module) brick of class Each 2 12725.00

designation 7.5

25 19.10 Extra depth for circuler type manholes 0.91 m internal dia ( at

bottom ) beyond 0.91m to 1.67 m .

19.10.1 with common burnt clay F.P.S.(non module) brick of class Meter 2 7591.80

designation 7.5

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU,

DETAILED PLUMBING ESTIMATE

SI.No. DSR-2023/ Description of Item UNIT TOTAL DSR RATE DSR AMOUNT

NON DSR QUANTITY @0.973)

26 19.16 Providing orange colour safety foot rest of minimum 6 mm Each 12 553.70

thick plastic encapsulated as per IS : 10910, on 12 mm dia

steel bar conforming to IS: 1786, having minimum cross

section as 23 mmx25 mm and over all minimum length 263

mm and width as 165 mm with minimum 112 mm space

between protruded legs having 2 mm tread on top surface by

ribbing or chequering besides necessary and adequate

anchoring projections on tail length on 138 mm as per 538.75 6,465.00

standard drawing and suitable to with stand the bend test and

chemical resistance test as per specifications and having

manufacture's permanent identification mark to be visible even

after fixing, including fixing in manholes with 30x20x15 cm

cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6

graded stone aggregate 20 mm nominal size) complete as per

Digitally signed by ARTI

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU, Jhansi

Sl. Item Description Unit Qty. Rate in Rs. GST FACTOR @ DSR Amount in

No. Code. 1.0633 Rs.

A. DSR- SCHEDULE ITEMS (DSR-2022) (PART-A)

1 D.S.R 1.10 Point Wiring in Medium Class PVC Conduit, with Modular type Switch:

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface/recessed

Medium Class PVC conduit, with modular type switch, modular plate, suitable size

of GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

2 1.55 Wiring for group controlled (looped) light point/fan point/exhaust fan 0.00 0.00

point/ call bell point ( without independent switch etc.) with 1.5 sq. mm

FRLS PVC insulated copper conductor single core cable in surface/

recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable etc. as required.

3 D.S.R 1.12 Wiring for light/power plug with 2x4 Sq.mm FRLS PVC insulated copper conductor Mtr. 300 334.00 355.14 1,06,542.66

single core cable in surface/recessed Medium Class PVC conduit along with 1 No. 4

Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing

etc. as required. Make:- Havells, Polycab, Finolex. Lap

4 D.S.R 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of 0.00 0.00

FRLS PVC insulated copper condcutor, single core cable in surface/ recessed

Medium Class PVC conduit as required. Make:- Havells, KEI, Finolex Lap. PVC

Conduit:- BEC AKG Precision

5 D.S.R 1.18 Telephone Wiring in Existing Conduit:- Supplying and drawing, following 0.00 0.00

pair, 0.5 sq.mm FRLS PVC insulated copper conductor, unarmoured telephone

cable in the existing surface / recessed steel / PVC conduit as required.

6 (D.S.R.) TV cable in Existing Conduit:- 0.00 0.00

Supplying and drawing, co-axial TV cable RG-6 grade 0.7 mm solid copper Mtrs. 50 47.00 49.98 2,498.76

conductor, PE insulated sealed with fibne tinned copper braid and protectedwith

PVC sheath in the existing surface/ recessed steel / PVC conduit as required.

7 D.S.R 1.21 S/F PVC Conduit: Supplying and fixing of following sizes of Med Class PVP 0.00 0.00

conduit along with the accessories in surface / recess & cutting the wall and

making good the same in case of recessed conduit as required for TV and TEL out

8 D.S.R. Supplying and fixing of following switch/ socket on the existing modular plate & 0.00 0.00

1.24 switch box including connections but excluding modular plate etc. as reqd.

1.24.5 6 pin 15/16 amp socket outlet Each 2 197.00 209.47 418.94

1.24.6 Telephone socket outlet Each 3 148.00 157.37 472.11

1.24.7 TV antenna socket outlet Each 2 148.00 157.37 314.74

9 D.S.R. Supplying and fixing Two Module Stepped type electronic fan regulator on Each 2 369.00 392.36 784.72

1.25 the existing modular plate & switch box including connections but excluding

modular plate etc. as reqd.

10 D.S.R. Supplying and fixing modular blanking plate on the existing modular plate & Each 20 40.00 42.53 850.64

1.26 switch box excluding modular plate as required.

11 D.S.R. Supply and fixing of following size/ modules, GI box along with modular base & 0.00 0.00

1.27 cover plate for modular switch/ regulator in recess, including connection as

1.27.4 6 module (200mmx 75mm) (for 2 nos. 6A Sockets & 2no. 6A Switch) Each 4 402.00 427.45 1,709.79

12 D.S.R. Supplying and fixing suitable size GI box with modular plate and cover in front on Each 32 477.00 507.19 16,230.21

1.31 surface or in recess including providing and fixing 3 pin 5/6 Amp modular socket

outlet and 5/6 A modular type switch, connections painting etc. as reqd. (for Light

13 D.S.R. Supplying and fixing suitable size GI box with modular plate and cover in front on Each 20 586.00 623.09 12,461.88

1.32 surface or in recess including providing and fixing 6 pin 5/6 & 15/16 Amp

modular socket outlet and 15/16 A modular type switch, connections painting etc.

14 D.S.R. Supplying & fixing of 3 pin, 5 amp Ceiling rose on the existing junction box/ Each 27 87.00 92.51 2,497.69

1.33 wooden block including connection as required.

15 D.S.R. Installation of exhaust fan in the existing opening, including making good the 0.00 0.00

1.50 damage, connection, testing, commissioning etc. as required.

16 D.S.R. Supplying and drawing of UTP 4 pair CAT 6 LAN Cable (AWG-23) in the existing 0.00 0.00

1.53 surface/ recessed steel/ PVC conduit as required.

17 D.S.R 2.3 Supplying and fixing following way single pole & neutral, sheet steel, MCCB 0.00 0.00

distribution board, 240V, on surface/ recces , complete with tinned copper bus

bar, neutral bar, earth bar, din bar interconnections, powder painted including

earthing etc. as required (But without MCCB/RCCB/Isolator)

2.3.1 6 way Double door (to Be use for HVAC OUT DOOR UNIT F/P MCB.) Each 2 2,206.00 2,345.64 4,691.28

18 D.S.R 2.4 Supplying and fixing following way, horizontal type thee pole & neutral, sheet 0.00 0.00

steel, MCCB distribution board, 415V, on surface/ recces , complete with tinned

copper bus bar, neutral bar, earth bar, din bar interconnections, powder painted

including earthing etc. as required (But without MCCB/RCCB/Isolator)

19 D.S.R 2.10 Supplying & fixing 5 amps to 32 amps rating 240/415 volts 10 kA, C curve 0.00 0.00

Miniature Circuit Breaker suitable for inductive loads of following poles in the

existing MCB DB complete with connections, testing and commissioning etc. as

2.10.5 Triple Pole and neutral Each 4 1,228.00 1,305.73 5,222.93

20 D.S.R 2.14 Supplying & fixing following rating double pole (Single Phase & Neutral) 240 V, 0.00 0.00

Resudual Curren Circuit Breaker (RCCB) , having a sensitivity current uo to

300mA in the existing MCB DB complete with connections, testing and

commissioning etc. as required. Make:-LEGRAND- DX³/SCHNEIDER- ACTI-

9/SIEMENS- BETA GUARD/ L&T- AU VERSION.

21 D.S.R Providing & fixing of M.V. danger notice plate of 200 mm x 150 mm, made of mild Each 4 269.00 286.03 1,144.11

2.21 steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with

inscription in single red colour on front side as required.

4.1 Supplying and installing following size of perforated painted with 0.00 0.00

powder coating M.S. cable trays with perforation not more than

17.5%, in convenient sections, joined with connectors, suspended

from the ceiling with M.S. suspenders including bolts & nuts,

painting suspenders etc as required.

4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre 50 777.00 826.18 41,309.21

22 D.S.R. EARTHING SYSTEM 0.00 0.00

i) 5.2 Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including accessories, and 0.00 0.00

providing massonry enclosure with cover plate having locking arragement and

watering pipe etc. with charcoal/cock and salt as required.

5.6 Earthing with copper Earth plate 600mm x 600mm x 6mm thick including Each 4 13,838.00 14,713.95 58,855.78

accessories, and providing masonary enclosure with cover plate having locking

arrangement and watering pipe of 2.7 Meter long etc. (with charcoal and salt as

required). (for UPS & Racks)

iii) D.S.R. Supplying and laying 25 mm X 5 mm GI strip at 0.50 meter below Mtr 130 144.00 153.12 19,904.98

5.9 ground/surface as strip earth electrode, including connection/ terminating with

nut, bolt, spring, washer etc. as required (Jointing shall be done by overlapping

and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)

iv) D.S.R. Providing and fixing 4mm dia copper wire on surface or in recess in 25 mm Mtr 460 155.00 164.81 75,813.29

5.17 medium class PVC PIPE for loop earthing as required.

23 D.S.R.- Supply, installation Testing and commissioning of 1200 mm sweep, BEE 5 star Each 35 2,730.00 2,902.81 1,01,598.32

2022 rated, ceiling with Brush Less Direct Current (BLDC) Motor,class of insulattion: B,

page no.- 3 nos. blades,30 cm long down rod, 2 nos. canopies, shacklet kit, safety rope,

72 copper winding, Power Factor not less than 0.9, Service Value (CM/M/W)

19.1 minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per

IS: 374-2019) THD less than 10% remote or electronic regulator unit for speed

control and all remaining accessories including safety pin, nut bolts, washers,

Temperature rise=75 degree C (Max.) insulation resistance more than 2 mega

ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as

Supplyinging and drawing of UTP 4 pair CAT 6 LAN Cable in the existing Mtr 180 57 60.61 10,909.46

surface/ recessed steel/ PVC conduit as required

TOTAL OF SCHEDULE ITEMS-(DSR-2022) (PART-A) 15,17,072.80

NON SCHEDULE ITEMS

1 MR Supplying of Exhaust fan of approved make as per instruction and Each 8.00 2880.00 23,040.00

2 MR Supplying of 2'X2' Panel light of 36 watt with hanging arrangement of Each 28.00 4140.00 1,15,920.00

approved make as per instruction and approval.

3 MR Supplying of tube light of 20 watt IP65 with hanging arrangement of Each 12.00 1220.00 14,640.00

approved make as per instruction and approval.

4 MR Hi wall Split units- Supply, Installation, testing and commissioning of Air- Each 10.00 71083.00 7,10,830.00

cooled DX type Hi-wall split air conditioners each comprising an outdoor

unit(s) consisting of hermetically sealed compressor suitable for

operation on 230V, 50Hz, 1 Phase AC supply, air cooled condenser,

condenser fan along with Cooling thermostats etc. with outer casing and

indoor fan coil unit consisting of centrifugal fans, fan motor, DX cooling

coil, outer casing, filter, control and power panel with remote etc. entire

cabling and wiring from indoor to outdoor (as per the actualdirection of

Engineer-in-charge), insulation and with full charge of refrigerant gas and

oil, supports, canvas connection etc. complete. The indoor and outdoor

units shall be with structural steel supports, angles, rods etc. The quoted

price shall also include 24G soft copper refrigerant piping of required

length from indoor to outdoor as per the actual direction of Engineer-in-

charge (minimum 20mtrs length) with 13 mm "O" class factory backed

nitrile rubber insulation with aluminum foil from outdoor unit to indoor

unit complete (as per the refrigerant pipe length), refrigerant charging,

PVC drain piping with 6mm thick nitrile rubber insulation, supports,

clamps, fittings, connections,

Video Surveillance System(IP CCTV)

5 MR SITC of IP Network PTZ Camera, 2MP IP PTZ Dome Camera, 1 / 2.8" Each 2.00 1,19,242.00 2,38,484.00

Progressive scan CMOS, 30x optical zoom, 4.7-141mm, 100M IR, Micro

SD card slot up to 256 GB, AC 24V/3A±10%/PoE, IP66 & IK 10, 2mp at

30FPS, 1920 x 1080 @60FPS, min 0.005 Lux @ F1.2 color view & 0 lux

for B/W with IR on, shutter time is 1/100000s~1s,AGC,AWB,Deblur,

Defog, EIS, True day/night, 120db True WDR, 3D DNR, HLC & BLC, Triple

streams, Smart codec by ROI, PTZ Position Display, 3D positioning, 300

Preset Points, 8 Patrols, up

to 8 presets each patrol; 4 Patterns 360° endless Pan,Pan Manual Speed:

0.1°~320°/s, Preset Speed: 320°/s, -5°~90°(Auto Flip), Tilt Manual

Speed: .1°~180°/s, Preset Speed: 180°/s, Should support

H.265+/H.265/H.264+/H.264/MJPEG,Audio & Alarm I/O por ONVIF

Profile S, T standard. CE, FCC, BIS approved including mounting

accessories complete as required

6 MR Supply, installation, testing and commissioning of 32 Channel NVR Each 1.00 2,63,001.00 2,63,001.00

7 MR Supply, installation, testing and commissioning of Enterprise Class 6TB Each 2.00 26,138.00 52,276.00

8 MR Supply, installation, testing and commissioning of Video Management Each 2.00 10,298.00 20,596.00

System (VMS) software shall be used to view live and recorded video

from capture cards and IP devices connected to local and wide area

networks. The VMS software shall have a client/server-based architecture

that can be configured as a standalone VMS system with the client

software running on the server hardware and/or the client running on

any network-connected TCP/IP workstation. Multiple client workstations

shall be capable of simultaneously viewing live and/or recorded video

from one or more servers. Multiple servers shall also be able to

simultaneously provide live and/or recorded video to one or more

workstations. The VMS server software shall also have the ability to be

installed on an IP edge device—such as an IP camera or encoder that

allows for 3rd party applications—allowing the device to serve as both a

server and IP video recording device.The VMS shall not charge for the

number of concurrent clients (min. 50 thick clients and 16 mobile clients

to be provided along with VMS).

9 MR Supply, Installation, Testing and Commissioning of Workstation PC: Each 1.00 1,24,515.00 1,24,515.00

Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz);

Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3

1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis:

Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT

Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R)

82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200

RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7

10 MR ProfessionalInstallation,Testing

Supplying, 64 Bit. & Commissioning of 55 " LED Full HD TV Each 1.00 1,19,763.00 1,19,763.00

Resolution 1920 x 1080 ,Contrast Ratio (Typical) 5000:1,Built-in

Speaker (10W + 10W), Magic Clone (to USB), Auto Source

Switching & Recovery, Lamp Error Detection, Super Clear Coating,

Temperature Sensor, Plug and Play (DDC2B), Pivot Display, Clock

Battery, PIP/PBP, Video Wall (10x10), Image Rotation, Button Lock,

HDCP Support, Smart Scheduling, Smart F/W update, Built-In

MagicInfo Premium-Swith Mounting Brackets as per Technical

Specification complete in all respect.

11 MR Supply, installation, testing and commissioning of 6 u/9" width, 650 mm Each 1.00 9,004.00 9,004.00

depth, rack assembly made of alluminium channels for the DVR and

associated equipment.

12 MR Supply and Installation of 3 watt LED Signage Each 10.00 12,590.00 1,25,900.00

13 MR SITC of interactive 3LCD based Projector with white board specially Each 1.00 8,50,876.00 8,50,876.00

designed for smart class room with Resolution:

WUXGA Contrast Ratio:16,000:1 Inputs &

Interfaces:Interactive,Brightness Range Lumens 3500:Ultra Short Throw

Features, Wifi,Network:

Wired LAN: RJ45 x 1 (100Mbps) Wireless: Optional (ELPAP10),Control

RS-232C: D-Sub 9pin x 1

Interactive Sync: Stereo Mini Jack IN x 1, OUT x 1

Touch Unit Control: Yes,Screen Size :

14 MR up to100” fixing & testing of approved make of 85 watt LED roadway /

Supplying, Each 5.00 4,876.00 24,380.00

street light luminaire with epoxy powder coatedsheet aluminium / steel

housing with epoxy white powder coated CRCA sheet steel gear tray

,clear acrylic cover with necessary materials connection including

mounting with GI pipe 32 mm OD, clamps on existing wall / pole etc.

complete as required

15 MR Supply, instalation, testing & commissioning of 13 Mtr High Mast System

hot dipgalvanised (singledip) and suitable for wind velocity as per IS875

part3, with lowering and raising motorized unit, with carriage assembly

for 6 Luminaries and its control gear box, lighting stand and avaition light

and lightning arrestor. The mast shallbe in three finished sections.It shall

also include accessories for 13 Mtr high mast including head frame,steel

wire rope 6mm dia,trailing cable,double drum winch,galvanized lantern

carriage arrangement suitable for 6 luminaires symmetrically & its control

gear boxes and lighting finial with internal power tool.

Supply, instalation, testing & commissioning of foundation bolts

manufactured from special steel alongwith nuts,washers, anchor plates &

Supply, instalation, testing & commissioning of control panel with suitable

control curcuit for automatic switching ON and OFFof the mast. It shall

also have suitable controls for operation of Power Tool.

Supply, instalation, testing & commissioning of 400W non integral LED Set 2.00 5,18,034.00 10,36,068.00

flood light luminaire with pressure die cast aluminium housing & heat

resistant toughened flat glass(IP 65) complete with external single

control gear box

16 MR Supply, installation, testing & commissioning of rating Invertors 1-phase

IN, 1-phase OUT complete as required & trolley and as per following

AC Voltage : 220V (-20% + 20%)

Phase : - 1-phase

Frequency : 50Hz, +/- 3Hz

AC Voltage : 230 V, ± 10%

Frequency : 50 Hz, ± 0.05%

Output Wave Form : Pure Sine Wave.

Output Wave form distortion : Less than 1%. Test report should be

provided for the same.

Transient Response : 0-100% step load, change in output voltage is 10 V

and recover back within 10 cycles.

Rated Power Factor : 0.8

Overload Capacity : 120% for 10 minutes.

: 120% for 10 minutes.

: 150% for 60 seconds.

Cooling System : Forced Air (In-built)

Battery Charger Type:

Recharge Time : Automatic boost cum float charging for enhanced life.

Back-up Type of Batteries : 30 minutes

Audio Alarm : Warning Buzzer for battery low.

Indications : Mains ON

Inverter OVERLOAD

AC input : SP MCB

DC fuse : Fuse in Battery Path

Output under voltage : Inverter Trips

Protection : Inverter Trips

Output overload : Current Limit

Protection : Both on Charger & Inverter

Short circuit : For Overload

Trip Facility : For Battery Low

: For Output Over Voltage

Control & User Connection:

Input through : 3 way terminal 3 core cable

Output through : 32 Amps output socket / terminal

Battery connection : 2 way terminal

Inverter ON/OFF : Rocker switch

Ambient Temperature : 0 to 50 C

Humidity : 20 to 90% non condensing

Noise Level : < 200 dB

Output capacity as follows:

Name of Project:- Establishment of Certification Laboratory for Organically/ Naturally Grown Product in Budelkhand Region at RLBCAU, Jhansi

S.No. Description of Item Unit Qty Rate Amount Ref Image

1 Reception Table nos

Dimension: 3000mm (L) x 900mm(D) x 1050mm(H)

Supplying and placing in position of 360 degrees revolving medium back chair of size: 660mm (L) x 490mm(D) x 1100mm(H) as per

photograph. The breathable mesh back chair with cushioned fabric seat shall be ergonomically design with adjustable lumbar back

support . The chair shall be provisioned with adjustable armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust

Movement). The seat cushion to be upholstered on 10-12mm thick water proof plywood and moulded foam. The seat to be made with 12

mm thick hot pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be

provided with self tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The

black Five star chrome base with hooded nylon castors..The pneumatic height adjustment shall have adjustment stroke of 100 mm and

shall be operated at 30kgs extension force.The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with

polyurethane foam, chair seat has foam of density 32-35 kg/m3.The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1

Certification/ SEDEX Certification/ GRIHA Certification and from the approved make.The product should be as per above given

specification under the guidance of Engineer in charge.

2 Reception Chair

Supplying and placing in position of 360 degrees revolving medium back chair of size: 660mm (L) x 490mm(D) x 1100mm(H) as per

photograph. The breathable mesh back chair with cushioned fabric seat shall be ergonomically design with adjustable lumbar back

support . The chair shall be provisioned with adjustable armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust

Movement). The seat cushion to be upholstered on 10-12mm thick water proof plywood and moulded foam. The seat to be made with 12

mm thick hot pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be

provided with self tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The

black Five star chrome base with hooded nylon castors..The pneumatic height adjustment shall have adjustment stroke of 100 mm and

shall be operated at 30kgs extension force.The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with

polyurethane foam, chair seat has foam of density 32-35 kg/m3.The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1

Certification/ SEDEX Certification/ GRIHA Certification and from the approved make .The product should be as per above given

specification under the guidance of Engineer in charge.

3 Sofa for Entrance lobby/ Student Common room/Staff Common room

3 seater Dimension(W)1650mm X (D)750mm X (H)710mm

Supplying, and placing in position of sofa as per Image.A supple premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Sitting proudly on sleek steel legs the sofa exudes a sense of comfort that is perfect for any

space. Material & subtype:Premium Leatherette, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact,

Style:Modern, steam beech solid wood have used for framing construction of sofa .The seat cushion is made of multi layered foam of

density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting

stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the

upholstery wrinke free & soft.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN

DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/

GRIHA Certification and from the approved make The product should be as per above given specification under the guidance of

Engineer in charge.

4 Sofa for Entrance lobby/ Student Common room/Staff Common room

SOFA TWO SEATER. Providing, fixing and Placing of Sofa of size 48x30x30 inch. (approx) as per indicative image. The Sofa have out

frame made out of 2nd Class Teak Wood in required shape. Legs and arms to made of 2nd Class Teak wood as per approved design.

wooden structure of sofa to be fabricated using good quality hard wood duly season & applying anti-termite treatment with paint and

polish to ensure stability of the frame. On wooden base frame of the sofa to be provided with M.S. helical spring, sides & back with jute

strips (Newar) 75mm wide, with polyfill covered with jute and finished with thick markin cloth before doing final upholstery.Seat - 40

Kg/cum density PU Foam, 100mm thick . All exposed teak wood shall be duly melamine polished . Sofa to be pholstered using approved

leatherite of A grade (0.8mm thick) of approved shade. The work should be complete as per Indicative image, approved samples/shop

drawings, specifications and direction of client/Engineer - In - Charge.

Digitally signed by ARTI

S.No. Description of Item Unit Qty Rate Amount Ref Image

5 Revolving Chair with High Back

High Back Revolving Chair - Providing and fixing High Back Mesh Chair with Headrest- SPECIFICATIONS: Back

Height - High Back with Headrest,Back Finish - Mesh with Lumbar Support,Back Mesh Color - Black,Seat Finish -

Fabric,Seat Fabric Color - Black,Seat Height Adjustment - Pneumatic,Mechanism Type - Synchronized Tilt,Back Tilt Lock -

Upright Position,Back Tilt Tension - Adjustable,Armrests Type - Fixed arms,Base Type - 5-Star in Black nylon base. The

work should be complete as per Indicative image, approved samples/shop drawings, specifications and direction of

client/Engineer - In - Charge

6 Visitor Chair

Supplying and placing in position similar to 360 degrees revolving medium back chair . The Craze chair of Size :-(W)590mm X

(D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour lumbar back design made of 12mm thick BWR

plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The leatherette upholstery in the chair has the

look and feel of top grain leather. The chrome plated loop armrest with padded upholstery is provided for extra comfort. The chair shall

be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors .

Chair seat has foam of density 30-35 (+/-2kg /m3) The backrest has a foam of 28kg/m3. The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO

Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved

make .The product should be as per above given specification under the guidance of Engineer in charge.

7 Meeting Visitor Chair for office

Medium back 360°-degree revolving chair as per image. all over size is: 600mm(l)x 660mm(d)x 1050mm(h), the chair made of full

upholstery in black colour.it will comes in finish in contemporary style. arms: armrest is having two adjustment heights (up & down).

use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back). seat: 40 ± 2 mm thick polyurethane foam with

density 32 (±3) kg per cu meter for best quality cushioning in seat, back: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg

per cu meter for best quality cushioning in back. backrest support foam design based on symmetrical lumbar support mechanism: self-

weighted multi locking mechanism. only seat size is 480mm(l) x 500mm(d) & the back size is 460mm(l)x 510mm(h)seat maximum nos 4 11,200 44,800

height is 550mm & minimum height is 450mm & back height from floor maximum height is 1050mm & minimum height is 950mm. gas

lift 100 mm telescopic haudraulic base: 650 mm chrome base with smooth castors.The product should be from manufacturer(OEM)

which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA

Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved make of .The product

should be as per above given specification under the guidance of Engineer in charge.

8 Table for Smart Class room/Examination Hall

Dimension:(L) 1200mm X (D) 600mm X (H) 750mm nos 10 22,330 2,23,300

Dimension:(L) 1800mm X (D) 600mm X (H) 750mm nos 6 34,991 2,09,946

Supplying, and placing in position of table as per image/Drawing. The top/work surface shall be 25

mm thk prelaminated particle board with 2mm thk pvc edge banding with 18mm thk prelaminated particle board modesty

panel with 2mm thk pvc edge bnading. Table top supported with MS powder coated square shape leg of 50mm x 50mm thk.

with horizontal connector of size 40mm x40mm thk. to support the tabletop The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO

Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the

approved make of Durian,

Godrej,HNI .The product should be as per above given specification under the guidance of Engineer in charge..

9 Chair for Smart Class room/Examination Hall

Supplying, and placing in position of chair as per image. The seat frame is constructed using sleek chrome with rich black leatherette

upholstery in stark contrast on the seat cushions. The tufted design on the seat and back adds to its style making this a perfect visitors

chair.Material & subtype: Premium Leatherette, Colour & Colour Family: Black, Dimension: (W)470mm X (D)400mm X (H)890mm,

Back Type:Low Back, Base:Four Leg Metal Frame, Base Type: Fixed, Maximum Seating Height: 19.29", Finish:Matte.The product should nos 68 7,560 5,14,080

be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/ INDIAN DESIGN MARK Certification / GREEN PRO

Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX Certification/ GRIHA Certification and from the approved

make .The product should be as per above given specification under the guidance of Engineer in charge.

Digitally signed by ARTI

S.No. Description of Item Unit Qty Rate Amount Ref Image

10 Warden Table

Dimension:1350mm(L)x 600mm(D)x 750mm(H)

Supplying and placing in position of office desk office desk structure of rectangular shape as per image.primary work surface overall size

is 1350mm(l)x 600mm(d)x 750mm(h) 25mm thick table top made of 25mm thick prelaminated particle board work surface with the

exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue . Modesty panel

made of 18mm thick, wire management hole with pvc grooment on table top. Construction right side of table top is based on a fixed

pedestal 3 drawers & from left side of table top is based on 18mm thk engineered wood pvc edge banding pedestal back,top,bottom &

drawers are made of 18mm thick with 1 cpu trolley made in black metal powder coated. Fixed pedestal:l:410mm(l)x 580mm(d)x nos 4 35,910 1,43,640

750mm(h) ,in provided with central lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18

mm along with facia of drawers.The product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification/

INDIAN DESIGN MARK Certification / GREEN PRO Certification/ AIOTA Certification/ BIFMA LEVEL-1 Certification/ SEDEX

Certification/ GRIHA Certification and from the approved make .The product should be as per above given specification under the

guidance of Engineer in charge.

Providing and fixing chromium plated SS curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed

11 with C.P. brass screws and PVC sleeves etc. wherever necessary complete : Mtr 73 723 52,779

Supplying and fixing of Main curtain for all heights / location with required width should comprise of suitable fabric of approved shade,

12 make and sample. Fabric width to be considered 1 mtr and height to be considered 2.1 mtr. Maximum fabric considerd for folding at Top Sqm 50 1,070 53,500

Total Amount Including GST@18% In Rs= 20,14,121

Total Amount Including GST@18% In Rs= 20,14,121

Digitally signed by ARTI