Development of Park near PHC in village Lakhnola ward no 15 in Municipal Corporation Manesar. REcall I

Good Earth for filling un-even land [HSR 3.1.2 plus 17.8.2 plus 17.8.3]

MOVABLE NET POLE

(i) 6 No. Ornamental Design FRP pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 15mm drilled in the base with hold fasts and having B class vertical m.s pipe of size 89 mm and height 2890mm, the central m.s pipe having FRP capital suitably mounted at appropriate height complete as per design enclosed. Complete pillar suitably grinded spray primered and subsequently spray painted with two coats of enamel paints is required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design copy enclosed. The spandrel (L-Bracker) having length 310mm and height 300mm the frieze (Top Panel) height 220mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 40mm x 25mm, frieze properly welded to the column pollars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with two coats of enamel paint. (iii) 3 No. cast iron base panel railing with frame Floral and Ornate decorative design cast iron side railing panel as per design copy enclosed having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 40 x 25 mm. the bottom mild steel pipe having 3 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 50mm welded at the base to hold the panel in the ground. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with two coats of enamel paint in required shade. (iv) One set of top frame with frp roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 2 mm thick bent to profile on either ends with clear width installation of frp sheets fixed horizontally along the length between column pillars. Each sheet enamel painted in red color on both sides. Each such sheet properly riveted to horizontal sheets. The roof pipe frames properly primered and painted in red color. The complete item is without C.C floor and without sitting bench. rates are including with all taxes

-merry go round 4 seater 5dia main frame is m s sq pipe round pipe centrel pipe which further pipe supports with pipe ball bearing assembly chair made of molded frp plastic pu primer and pu paints

Supply and erection of 16 sqmm 4 Core Aluminium unarmoured Cable in existing pipe or trenches complete in all respect.

Providing And Installation Of Kids Play Equipment - Monkey Bar AREA : 8 X 3.5 X 7 FEET AGE GROUP : 8-15 YRS M.S : 60 MM, 27 MM CAPACITY : 2-3 “A” Class ISI marked MS Pipe of Reputed Brand (Jindal, Apollo, Bharat Etc). FRP Thickness between 3 To 8 mm. PU Coated Paint finish on the MS Structure. As Per Approved Design, including fixing In Ground With cement concrete at specified location till the satisfaction Of Engineer Incharge. As per reference image attached in annexure. Including GST and other Charges.

Leg Press: Providing designing and fixing of leg press of size 2000x550x1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micror thick

Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and ishapod welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Officer -in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of. equipment etc.`` `

Double Cross Walker/ Cross trainer double:- Providing, and fixing Double Cross Walker of size 1600 X 600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the G.I pipes are 40 mm dia and 2.5 mm thick all G.I pipes made up of hot rolled tubular steel and hot dipped

Horse Rider Station:- Providing, and fixing of horse rider station of size 1000 x 600 x 1100 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Alczo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge.Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and a. .royal of arge regari ing materia , s ape of equipment,colour on metal, seat and