Construction of building including clean room facility (class 100000 In working condition) for TOP and maintenance of INS-Sigma 30 N and other Electro-Optic Devices at Ordinance Factory Chandigarh

ABSTRACT OF COST-CIVIL

S No ITEM OF CIVIL WORK AMOUNT

1.00 Earth Work Rs. 39,76,445 0

2.00 Concrete Work Rs. 15,38,951 0

5.00 Marble Work Rs. 3,58,308 0

7.00 Steel Work Rs. 21,89,327 0

11.00 Aluminium Works Rs. 24,74,288 1,10,75,609

12.00 Glazing Works Rs. 46,53,835 0

13.00 Water Proofing Work Rs. 47,57,348 0

15.00 Rainwater harvesting & Tube well Rs. 10,02,475 0

Total Amount Rs. 131698917 67632481

Total Amount Rs. 131698917 67632481

GRAND TOTAL 199331398

GRAND TOTAL 199331398

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

1.00 2.0 EARTH WORK

Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15

cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and

1.02 2.6 disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

1.03 2.25 layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and 2420.00 513.00 2933.00 Cum 196.00 5,74,868.00

watering,lead up to 50 and for all lift.

Disposal of surplus earth by mechanical transport including loading, unloading for a lead upto 10

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and

dressing complete

1.06 2.34 Supplying chemical emulsion in sealed containers including delivery as specified

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 935.00 47.00 982.00 Litre 234.75 2,30,524.50

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment

(excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion@ one litre per hole,300 mm apart

a) 2.35.3 including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement: 2 Coarse

sand) to match the existing floor:

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 1683.00 85.00 1768.00 Sqm 310.05 5,48,168.40

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked

Excavating, supplying,stacking and filling of local earth (including royalty) by mechanical transport

1.09 2.25(a) upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm 5.00 5.00 Cum 700.50 3,502.50

in foundation trenches, plinth, sides of foundation etc. complete for all lift.

Total Earth Work : 39,76,444.73 0.00

2.00 4.0 CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering

and shuttering - All work up to plinth level:

1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate

40 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including

attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing

2.02 4.2 courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up

to floor five level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-Ill) derived from natural sources: 4 graded stone aggregate

20 mm nominal size derived from natural sources)

1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources: 6 graded stone aggregate

20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement: 2

2.03 4.10 coarse sand (zone-Ill) derived from natural sources: 4 graded stone aggregate 12.5 mm nominal 165.00 32.00 197.00 Sqm 410.85 80,937.45

size derived from natural sources)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight Per bag of

2.04 4.12 of cement as per manufacturer's specification. 43.00 9.00 52.00 cement of 18.15 943.80

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality

2.05 4.13 using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and 165.00 32.00 197.00 Sqm 146.15 28,791.55

finally with apiece of cloth lightly soaked in kerosene oil.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill)

derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural

2.06 4.17 sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and 278.00 278.00 Sqm 749.30 2,08,305.40

consolidated and grouted with fine sand, including necessary excavation, levelling & dressing &

finishing the top smooth.

Total Cement Concrete work : 15,38,950.60 0.00

3.00 5.0 R.C.C. WORK

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural

sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of laying,

curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note:

Extra cement up to 10% of the minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than 110% of the specified minimum

cement content, the contractor shall have discretion to either re-design the mix or bear the cost of

5.33.1 All works upto Plinth level

b) 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum 1118.00 144.00 1262.00 Cum 9,504.75 1,19,94,994.50

5.33.2 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum 973.00 34.00 1007.00 Cum 9,860.40 99,29,422.80

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of

centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 206382.00 19811.00 226193.00 Kg 107.85 2,43,94,915.05

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more 174911.00 4246.00 179157.00 Kg 107.85 1,93,22,082.45

3.05 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

a) 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 509.00 87.00 596.00 Sqm 392.15 2,33,721.40

b) 5.9.3 Suspended floors, roofs, landings, balconies and access platform 2056.00 103.00 2159.00 Sqm 927.25 20,01,932.75

c) 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers 3211.00 217.00 3428.00 Sqm 736.40 25,24,379.20

d) 5.9.19 Weather shade, Chajjas, corbels etc., including edges 145.00 3.00 148.00 Sqm 951.10 1,40,762.80

e) 5.9.7 Stairs, (excluding landings) except spiral-staircases 92.00 92.00 Sqm 764.95 70,375.40

f) 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 1971.00 158.00 2129.00 Sqm 961.30 20,46,607.70

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses,

bands, copings, bed plates, anchor blocks and the like

i) 5.9.16 Edges of slabs and breaks in floors and walls

j) 5.9.14 Extra for shuttering in circular work (20% of respective centering and shuttering items) 1.00 1.00 Sqm 192.26 192.26

k) 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc 55.00 279.00 334.00 Sqm 842.50 2,81,395.00

3.06 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 183.00 6.00 189.00 metre 78.40 14,817.60

Extra for additional height in centering, shuttering where ever required with adequate bracing,

3.07 5.11 propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m,

for every additional height of 1 metre or part thereof (Plan area to be measured).

5.11.1 Suspended floors, roofs, landings, beams and balconies (Plan area to be measured 1927.00 1927.00 Sqm 384.30 7,40,546.10

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for

expansion joints.

Providing and fixing of expansion joint system related with floor location as per drawings and

direction of Engineer-In-Charge. The joints system will be of extruded aluminium base members,

self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The

system shall be such that it provides floor to floor /floor to wall expansion control system for various

vertical location in load application areas that accommodates multi directional seismic movement

without stress to it`s components. System shall consist of metal profiles with a universal aluminium

base member designed to accommodate various project conditions and finish floor treatments. The

cover plate shall be designed of width and thickness required to satisfy projects movement and

3.09 5.44 loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-

centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement

shall exhibit circular sphere ends that lock and slide inside the corresponding aluminium extrusion

cavity to allow freedom of movement and flexure in all directions including vertical displacement.

Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory

requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material

shall confirm to ASTM 6063).

Providing and fixing of expansion joint system related with wall joint (internal/external) location as

per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminium base

members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The

material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/

3.10 5.45 wall to corner application, both new and existing construction in office Buildings and complexes with

no slipping down tendency amongst the components of the Joint System. The Joint System shall

utilize light weight aluminium profiles exhibiting minimal exposed aluminium surfaces mechanically

snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system of approved make and manufactures for various roof

locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of

extruded aluminium base members with, self aligning and self centering arrangement support

plates as per ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof

to corner joint cover expansion control system that is capable of accommodating multidirectional

seismic movement without stress to its components. System shall consist of metal profile that

incorporates a universal aluminium base member designed to accommodate various project

conditions and roof treatments. The cover plate shall be designed of width and thickness required

3.11 5.46 to satisfy movement and loading requirements and secured to base members by utilizing

manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all

directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide

inside the corresponding aluminium extrusion cavity to allow freedom of movement and flexure in all

directions including vertical displacement. The Joint System shall resists damage or deterioration

from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic

from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have

water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063).

4.00 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 16.00 15.00 31.00 Cum 7,132.25 2,21,099.75

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 715.00 69.00 784.00 Cum 9,105.95 71,39,064.80

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundations and plinth in :

6.12.2 cement mortar 1:4 (1 cement: 4 coarse sand) 5.00 5.00 Sqm 905.05 4,525.25

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 322.00 322.00 Sqm 1,123.80 3,61,863.60

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick

with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super

4.06 6.38 structure above plinth level up to floor V level in cement mortar 1:4 (1 cement: 4 coarse sand ). The 5.00 5.00 Cum 10,195.45 50,977.25

rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300 mm

thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super

structure above plinth level up to floor V level with RCC band at sill level and lintel level with

4.07 6.47 approved block laying polymer modified adhesive mortar all complete as per direction of Engineer- 5.00 5.00 Cum 8,333.65 41,668.25

in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Analysed on Providing and filling AAC blocks including proper watering and compaction in sunken areas all

DSR complete as per drawings and as directed by the Engineer-in-chargein-Charge.

Total Brick Work : 78,53,468.50 71,640.00

5.00 8.0 MARBLE WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of

required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1

5.01 8.2 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy

touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc.

complete at all levels.

8.2.2 Granite stone slab of colour black, Cherry/Ruby red

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen

platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary

5.02 8.5 holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 13.00 5.00 18.00 Each 978.70 17,616.60

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm

deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase

5.03 8.10 cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of

Engineer-in-charge and finished smooth.

8.10.2 Granite Stone of approved shade 2.00 2.00 Sqm 4,051.85 8,103.70

Total Marble Work : 3,58,308.10 0.00

6.00 9.0 WOOD WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

6.01 9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold

fast lugs or dash fastener shall be paid for separately).

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative

type, core of block board construction with frame of 1st class hard wood and well matched

6.02 9.21 commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of

9.21.1 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws 84.00 5.00 89.00 Sqm 2,392.65 2,12,945.85

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of

flush door shutters (over all area of door shutter to be measured).

Providing and fixing Stainless steel satin finish SS 304 grade Sliding Door bolts for wooden doors of

6.04 MR approved make and model all complete as per the directions of Engineer-in-charge

Providing and fixing Stainless steel satin finish SS 304 Tower Door bolts for wooden doors of

approved make and model all complete as per the directions of Engineer-in-charge

Providing and fixing Stainless steel satin finish SS 304 grade Handle SS screws for wooden doors

MR of approved make and model all complete as per the directions of Engineer-in-charge

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of

6.07 9.113 approved quality for aluminium door, with necessary screws etc complete as per direction of 33.00 2.00 35.00 Each 850.05 29,751.75

Engineer- in-charge.

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating

6.08 9.101 not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with

necessary screws etc. complete.

9.101.2 Twin rubber stopper 38.00 38.00 Each 72.35 2,749.30

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having

6.09 9.83 brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 38.00 38.00 Each 1,124.85 42,744.30

700 mm), with necessary accessories and screws etc. complete.

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter

6.10 9.53 bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 376.00 12.00 388.00 Each 228.85 88,793.80

mix (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/

6.11 9.127 suede finish with high density protective surface layer and reverse side of adhesive bonding quality

conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60

mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not

less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame

shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a

provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10

6.12 9.161 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing 99.00 99.00 Metre 2,202.90 2,18,087.10

Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a

approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per

the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minutes Fire rating

conforming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved

by Engineer-in-Charge, with suitable mounting on door frame, consisting of vertical styles, top rail &

side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6 mm thick G.I.

6.13 9.162 sheet (zinc coating not less than 120 gm/ sqm) duly filled mineral wool insulation having density 76.00 76.00 Sqm 12,017.90 9,13,360.40

minimum 96 kg/ cum and fixing with necessary stainless steel ball bearing hinges of size 100x89x3

mm of approved make, including applying a coat of approved fire resistant primer or powder

coating not less than 30 micron etc all complete as per direction of Engineer-in-Charge (panelling to

be paid for seperately).

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I.

beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/sqm) of size 20 x

33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c ,

6.14 9.164 including applying a coat of approved fire resistant primer/ powder coating of not less than 30

micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per

NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-Charge

with glass of required thickness having 120 minutes of fire resistance both integrity & radiation

control (EW120) and minimum 20 minutes of insulation (El20). The manufacturer have to give test

report/certification of fire glass and the glass should have the stamp showing the value of E, EW &

El. The glass shall be tested in approved NABL accredited lab or by any other accreditation body 76.00 76.00 Sqm 43,677.65 33,19,501.40

which operates in accordance with ISO/IEC 17011 and accredited labs as per ISO/IEC 17025 for

testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than

1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on

6.15 9.139 back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- 23.00 23.00 each 8,366.15 1,92,421.45

charge, all complete.

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free

uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles

having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series

R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with

galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC

extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate

dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with

countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished

6.16 9.147 A wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel

screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion

welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware

and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall

be filled with weather proof silicon sealant over backer rod of approved size and quality, all

complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-

Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design

approved by Engineer-in-Charge.

Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/ without high

performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be

paid separately. Note:- Structural design proof checked from a Government Engineering Institute,

to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 -

Part 3 (ii) Sites with structure height more than 20m for all wind speeds

Note:- Structural design proof checked from a Government Engineering Institute, to be provided by

the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with

structure height more than 20m for all wind speeds

9.147.C2 Fixed window/ ventilator with mullion / transom.

Using R2 series with frame (39 mm & above ) x (39 mm & above) & mullion (39 mm & above) x (60

9.147.C2.2 mm & above). (Height upto 1.2 metre) 1.00 1.00 Sqm 8,765.40 8,765.40

Casement window double panels with French (False) Mullion with S.S. 304 friction hinges as per

9.147.E3 size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles.

Using R4 series with frame (64 mm & above) x (50 mm & above) & sash (64 mm & above) x (70

9.147.E3.3 mm & above) & French (False) mullion (64 mm & above) x (60 mm & above). (Height above 1.8 6.00 6.00 Sqm 12,496.30 74,977.80

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of

6.17 9.140 approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of

Engineer-in- charge (Frame work shall be paid for separately).

9.140.1 12 mm thick commercial ply conforming to IS : 1328 BWR type 1105.00 1105.00 Sqm 1,224.65 13,53,238.25

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183

having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with

6.18 12.57 screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per 1105.00 1105.00 Sqm 358.50 3,96,142.50

directions of Engineer-in-Charge.

7.00 10.0 STEEL WORK

Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm

dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10

7.01 10.27 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as

per direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting

the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary

7.02 10.28 accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top 934.47 934.47 Kg 772.40 7,21,787.79

of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-

charge, (for payment purpose only weight of stainless steel members shall be considered excluding

fixing accessories such as nuts, bolts, fasteners etc.).

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

7.03 10.2 including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all 3.00 3.00 Kg 133.70 401.10

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including

7.04 10.16 cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including

welding and bolted with special shaped washers etc. complete.

a) 10.16.2 Hot finished seamless type tubes 12.00 12.00 Kg 206.35 2,476.20

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and

7.05 10.25 applying a priming coat of approved steel primer using structural steel etc. as required

a) 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 500.00 5166.00 5666.00 Kg 172.60 9,77,951.60

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths,

interlocked together through their entire length and jointed together at the end by end locks,

mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside

7.06 10.6 and outside locking with push and pull operation complete, including the cost of providing and fixing

necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate

strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

a) 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover 22.00 22.00 Sqm 3,653.20 80,370.40

7.07 10.7 Providing and fixing ball bearing for rolling shutters. 2.00 2.00 Each 492.35 984.70

7.08 10.8 Extra for providing mechanical device chain and crank operation for operating rolling shutters.

a) 10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area 22.00 22.00 Sqm 1,281.35 28,189.70

Total Steel Work : 21,89,326.94 0.00

8.00 11.0 FLOORING

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,

8.01 8.31 over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey 5.00 84.00 89.00 Sqm 1,267.95 1,12,847.55

cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching

shade complete.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by

the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as

8.02 11.37 White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse 584.00 120.00 704.00 Sqm 1,096.55 7,71,971.20

sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement

and matching pigment etc., complete

Providing and laying Leather finish Granite stone flooring in required design and patterns, in linear

as well as curvilinear portions of the building all complete as per the architectural drawings with 18

mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse

8.03 sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with

pigment of matching shade including rubbing, curing and polishing etc. all complete as specified

and as directed by the Engineer-in-Charge :

a) Leather finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 121.22 121.22 Sqm 5,331.00 6,46,207.99

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as

well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand)

8.04 laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of

matching shade including rubbing , curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

a) Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent 786.00 786.00 Sqm 4,450.00 34,97,700.00

Granite stone slab 18 mm thick in risers of steps, skirting,and Cladding laid on 12 mm (average)

thick cement mortar 1:3 (1 cement : 3 coarse sand ) and jointed with grey cement slurry mixed with

8.05 MR pigment to match the shade of the slab, including rubbing and polishing complete. 518.00 518.00 Sqm 8,168.00 42,31,024.00

8.06 11.24 Extra for pre finished nosing to treads of steps of marble stone. 112.00 112.00 metre 719.90 80,628.80

Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved

8.08 11.41 make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand),

jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and

matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with

water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours &

8.09 11.46 shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse

sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement

& matching pigments etc. complete

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar

refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped

surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse

8.10 12.55 sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including 1710.00 20.00 1730.00 Sqm 1,703.95 29,47,833.50

rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm

height along the parapet walls in the same manner.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement

8.11 11.26 slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete

with base of cement mortar 1 : 4 (1 cement: 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average)

thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with

8.12 11.27 pigment to match the shade of the slabs, including rubbing and polishing complete. 1.00 1.00 Sqm 2,354.70 2,354.70

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall

lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement

8.13 8.15 : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever 497.00 497.00 Kg 714.40 3,55,056.80

Providing and applying a 4 component Conductive System using the EPOXY SYSTEM at 1 to

2mm thickness the System Built Up sequences are as following ,Priming the prepared substrate

with 1-2 coats of solvent free 2 component epoxy primer , followed by 1st coat of -Conductive

Middle coat at 90 - 100 microns allowing it to dry when tested shall have conductive range of < 10^3

and installing copper strips (peel & stick, 12-20mm wide and 70-100 micron thick) at the periphery

of the primed surfaces, to form grid pattern fixed within the area at 3m centres. The applied tape

8.14 MR matrix should be secure and fully bonded to a confirmed earth point. There should be an earthing 476.00 476.00 Sqm 2843.00 13,53,268.00

point for every 100sqm floor area. applying 2nd coat of -Conductive Middle coat at 70-100 micron)

and allowing it to dry, applying the Top Coat, conductive range of >10^4 - <10^6Ω epoxy floor, by

mixing all components by mechanical means, spreading at 2mm thickness using notch trowel or

depth set rake trowel, rolling the surface using spike roller and finishing, allowing it to dry

completely, including grinding, cleaning etc and complete as per manufacturer's

specification.EPOXY Underlayment at 1mm thickness + 1mm thickness (total thickness 2)

Engineered Wooden Flooring:

Supplying and Installation of engineered wooden flooring of total thickness 13 mm -16 mm,

8.15 MR Toplayer PEFC controlled Core board PEFC controlled Backing layer PEFC controlled sources 108.00 108.00 Sqm 6168.00 6,66,144.00

Wood Veneer 3 mm Tongue and groove Length Uniclic Width Uniclic Multifit Domestic use

Conditions as per direction of engineer in charge.

Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish.

8.16 MR Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ 584.00 584.00 Metre 357.00 2,08,488.00

PVC Jointers and Gasket.

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required

pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick

stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand)

8.17 laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry

MR admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining

(veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever

required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3

8.18 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including

MR pointing with white cement slurry admixed with pigment of matching shade, including rubbing,

curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-

18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and laying Cobble stone flooring Size: 6” x 6” Thickness: 22 mm (±2mm) in required

design and patterns all complete as per the architectural drawings with 18 mm thick stone slab over

20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with

8.19 MR cement slurry and pointing with white cement slurry admixed with pigment of matching shade 353.00 353.00 Sqm 3,042.00 10,73,826.00

including rubbing , curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Concrete panels on façade: Concrete wall panels are specifically designed for practical solutions for

both indoor and outdoor spaces. They are advanced form of UHFRC (Ultra High-Performance

Fiber Reinforced Concrete) meticulously crafted for architectural applications. This innovative

concrete solution seamlessly integrates cutting-edge strength, versatility, and aesthetic refinement.

The panels offer lightweight, high density, and low porosity, ensuring durability. Additionally, explore

possibilities for XL formats and the benefits of imported pigments with UV resistance for long-

lasting appeal. The panels have a starting thickness of 8 mm, and variations in thickness are

determined by the standard collection designs with an option to choose from a range of textures to

achieve a personalized aesthetic

Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated

rainscreen tiles of height 250/ 300/ 400 mm and length of 595 mm of approved texture,design and

pattern having Flexural Strength/ Modulus of Rupture of ≥ 14 N/m² and maximum water absorption

of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to

a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical ‘T’ (for intermediates)/

‘L’(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2 mm/ 40x60x2 mm / 40x40x2

mm respectively, spaced at maximum spacing of 600 mm c/c matching to the tile vertical grid, and

horizontal aluminium ‘C’-clamps of size 56x25x2 mm thickness of length 150 mm at junction of tiles

and of length 75 mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/

300/ 400 mm c/c matching to the tile horizontal grid with two numbers of self-drilling / self-tapping

SS screws of size 5.5x25 mm with EPDM washers. The vertical ‘T’/’L/ Tubular’ sections shall be

fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum

80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size

220x110x12 mm at outer corners and stainless steel grade 304,M10 full threaded anchor fasteners

with nylon sleeve 100 mm long (for brick work) and M8 expansion anchor fasteners 75 mm long for

concrete surface, spacing of brackets to be based on a structural/ static calculation. The brackets

8.21 MR shall be of length 175 mm at junction of two vertical aluminium profiles and of length 100 mm at

intermediate points of vertical profiles and shall be fixed to the vertical aluminium T / L / Tubular

profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25 mm with EPDM

washers. EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be

mounted on the ‘C’ clamps such that the tiles are supported at top and bottom at both ends. The

tiles shall be additionally secured to the horizontal ‘C’ clamps using special SS clips of required size

which shall be inserted and pressed into position on the ‘C’ clamps holding the tiles and the cut-tiles

shall be glued at points to the horizontal ‘C’ clamps by using MS Polymer sealant adhesive. The

vertical joint open groove between two adjacent tiles shall be 5 mm. The tiles and system shall be

designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be

installed using the ventilated rain screen principle with provision for natural ventilation of the space

between the façade tiles and the structural wall. The work shall be carried out as per specification,

drawing and as per direction of the Engineer-in-Charge.

Note: Scaffolding wherever required to be paid separately

With 16 mm thickness (+/- 10%) terracotta tiles of grey colour 1874.00 1874.00 Sqm 10,855.00 2,03,42,270.00

Total Flooring Work : 50,60,189.45 4,37,52,381.99

9.00 12.00 Roofing Work

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate

9.01 12.21 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per

standard design :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m

9.02 12.22 x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat 20.00 4.00 24.00 Each 298.25 7,158.00

of neat cement, rounding the edges and making and finishing the outlet complete.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm

thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the

angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end

of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200

mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia

x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm

9.03 12.45 high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with

the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of

tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification and also including the cost

of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels

suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge

but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-(Part I) :2011 (Board with

BIS certification marks)

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 %

perforated area with perforation size and pattern as approved by the Engineer- in-charge and as

b) 12.45.4 per manufacturer's specification, with all 4 sides tapered and backed by acoustical tissue with NRC 103.00 103.00 sqm 1,744.15 1,79,647.45

value not less than 0.60

Gypsum Design Panel: Providing and fixing suspended false ceiling: Designpanel M2F, Size

1200x2400x12.5mm perforation 3X3mm,8.3MM C/C with 7.1 - 9.8% perforation and NRC upto

0.70: Micro perforation of glass-fibre reinforced gypsum material, which includes providing and

fixing GI perimeter channels The furring should be min. 60 mm wide at the short end joints (if wood

is used; the steel furring can be min. 45 mm). The remaining furring can be 45 mm wide. of size

0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along

the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and screws,

at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two

flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm

x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55 mm

thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the

intermediate channels with help of connecting clips and in direction perpendicular to the

intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling

section with 25 mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing

is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the

boards are to be joined and finished so as to have a flush look with jointing compound.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Supply and installtion of Metal open Cell ceiling made of GI made and powder coated of approved

RAL shade. open cell ceiling with cell size of 50 x 50 mm. The cell is formed by locking of upper

sections and lower sections with U shaped profiles of 40mm height 15mm width and 595 mm

length. The upper and lower sections when locked are locked with end panels on all 4 sides to form

a tile of 595 x 595mm. Each tile is installed on a 15mm T Grids system The grids system is formed

by locking of GI made Main T of 3000mm or 3600mm length and GI Cross T of 600mm at 600mm

c/c. GI wall angle 25x25 x0.4x3000mm {Material-GI(IS513),YS-280Mpa,Finish-Galvanised

90GSM(IS277)} is fixed along the periphery of the ceiling with wooden screws at 300mm centers or

Hilti HPS 6x40mm placed at 600 mm c/c. The grid system is suspended by 4 mm wire rod with

adjustable clip, connected to the grids system at 1200mm c/c. The suspension rod with clip is fixed

to the slab by means of soffit cleat and rawl plug ( fastner), at 1200mm c/c. Gyproc® soffit cleat

27x37x25x1.6mm {GI(IS513)YS-260Mpa, Finish-Galvanised 120GSM(IS277) } is fixed with

Gyproc® Rawl Plug- Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating (7 to 8 microns) pull out

load- 6.8kN for M30 concrete grade} Suspension etc. all complete as per direction of Engineer-in-

charge.. (Make- SAINT GOBAIN/ Product should be GreenPro Certified / IGBC / GRIHA Compliant.

Product should be GreenPro Certified / IGBC / GRIHA Compliant. Manufacturing- Make In India

(Govt. of India Initiative). System should be complete in all respect as per direction of Engineer-in-

Providing and fixing G.I Plain 84mm wide x12mm deep panel with 16 mm flush profile to make it

100mm module of length upto 6mtr, shall be roll formed out of 0.5mm thick Powder Coated .The

top coat of panel shall be 60 micron polyester coated finish in approved colour. The panel shall be

factory cut in up to 6Mtr OR required length. Accessories Detail:Carrier: 32 mm wide and 39mm

9.06 MR deep, made out of 0.5mm thick steel backed with enameled black paint having cut out to hold on 345.00 345.00 sqm 2,219.00 7,65,555.00

panel in a module of 100mm closed. The joint of two carriers shall be joined by means of carrier

splices maintaining a module of 100mm .4mm dia galvanized rod with special height adjustment

butter fly clips made out of SS steel sheet. The edge profile G.I.shall be matching with the panel.

300x1200 Suspended False Ceiling: Providing and fixing suspended false ceiling microlook

tegular edge tile with 15 mm thickness, easily demountable tile, manufactured from High density

glass wool, visible surface is a batch painted glass tissue in white, back of the tile covered with

glass tissue. Size 1200x600x15mm Acoustics-Sound absorption(Alpha W) - 0.95 at 200 mm o.d.s

as per EN ISO 354 Acoustics-Sound absorption Class - Class A at 200 mm o.d.s as per EN ISO

9.07 MR 11654Acoustics-Articulation class - 180 as per ASTM E1111, ASTM E1110,NRC - 0.9 NRC as per 428.00 428.00 sqm 3,084.00 13,19,952.00

ASTM C 423,Humidity Resistance -Permanent ambient RH up to 95% at 30*C without sagging,

warping and delaminating ( 13964:2014). Fire Safety - Tested and classified as non combustible

according to EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501-

1 - European Standard.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Supply, Installation, Testing and Commissioning of STRETCHED FABRIC CEILING: Supply &

installation of fabric false ceiling / wall formed out with TRANSLUCENT Printed fabric coverings

made out of polyester knitted fabric coated with Polyurethane (PU). The TRANSLUCENT Printed

fabric width of 2m, 3m, 4.1m &5.1m with weight of 200gm/m2, thickness of 0, 3 mm. The

appearance of fabric is matt, smooth and uniform with blanq color and light transmission of 50%.

The tear strength of fabric should be accordance to CH: 4,5daN; TR: 6,5 daN. The fire rating should

be accordance to B-S1, d0. The fabric should be humidity resistant and free of carcinogenic

substances (CMR) or volatile organic Compounds (VOC’s). At labeling in accordance with the

French decree no. 2011- 321, Oeko-Tex standard100 certified. Fabric should be installed with

approved manufacturer guidelines. It comes with 10 year manufacturer guarantee. The installation

9.08 MR of TRANSLUCENT Printed fabric should be dry installation & done at room temperature using 8.00 8.00 sqm 13,020.00 1,04,160.00

CLIPSO PVC, ABS Grippers. Clipso ceiling base to be made of MS or Wooden frame finishing to a

flush finish of tapered and square edges in desired design as per architect specification. Supply of

LED Lights behind the Fabric Wall/ False ceiling in modules/ PCB with recommended wattage as

per manufacturer's standards to give an effect of ambient lighting. LED make MLS/ Bridgelux/

Osram- SMD 2835, LED spacing / Pitch should be at least 73-80mm with beam angle of 170

degree, Colour temperature should be as per design intent 3000K/4000K/6000K. Wattage of 8-

10W/mtr. LED modules/ PCB should be positioned properly to provide an even light flow, casting

no shadows or dark spots. Dali Dimmable Driver cost included.

Total Roofing Work : 17,44,811.85 50,34,467.00

10.00 13.00 FINISHING

10.01 13.40 12 mm cement plaster of mix :

10.02 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:

10.03 13.16 6 mm cement plaster of mix:

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5

10.04 13.11 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). 2498.00 810.00 3308.00 Sqm 518.55 17,15,363.40

Extra for plastering exterior walls of height more than 10 m from ground level for every additional

height of 3 m or part thereof.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare

the surface even and smooth complete.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less

10.07 13.82 than 50 grams/ litre, of approved brand and manufacture, including applying additional coats

wherever required, to achieve even shade and colour.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give

an even shade :

13.62.1 Two or more coats on new work 48.00 103.00 151.00 Sqm 226.25 34,163.75

10.09 13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior

primer applied @ 2.20kg/10 sqm

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50

10.10 13.41 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve

even shade and colour :

New work (two or more coats) over and including water thinnable priming coat with cement primer

having VOC content less than 50 gram/litre

Providing and applying white cement based putty of average thickness 1 mm, of approved brand

10.11 13.80 and manufacturer, over the plastered wall surface to prepare the surface even and smooth 125.00 125.00 Sqm 156.05 19,506.25

10.12 13.114 Melamine polishing on wood work (one or more coat). 194.00 11.00 205.00 Sqm 1,192.30 2,44,421.50

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing & fixing Panelling (PU Paint) with G.I. framework with 45x25mm GI sections (India

Gypsum) @ 600mm c/c in both directions with 12mm thick exterior grade MDF board fixed on

10.14 MR frame. Item includes finishing panelling MDF board surface with high gloss PUpaint (Asian/ Berger/ 433.00 433.00 Sqm 10,575.00 45,78,975.00

ICI) with gun spray after preparation of surface as per manufactrer's specification etc. complete to

the satisfaction of Architect/ Engineer-in-charge.

Preparation of complete set of drawings based on the concept drawings including finishing, MEP

services, details, design calculations etc. and for preparation of as built drawing, any other details

10.15 MR as and when desired by Engineer-in-charge/ client. A qualified professional for the purpose shall be 1.00 LS 2950000.00 29,50,000.00

appointed after due approval from Engineer-In-Charge.

Total Finishing Work : 67,25,135.65 75,28,975.00

11.00 21.00 ALUMINIUM WORKS

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built

up standard tubular sections/ appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/

11.01 21.10 neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for glazing /

panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) 1977.00 8.00 1985.00 Kg 530.90 10,53,836.50

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and

11.02 21.1.2 making provision for fixing of fittings wherever required including the cost of EPDM rubber /

neoprene gasket required (Fittings shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron 13.00 13.00 26.00 Kg 634.45 16,495.70

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with

EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions

11.03 21.30 of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 1.00 6.00 7.00 Sqm 1,505.25 10,536.75

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators

and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including

11.04 21.10 providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and 248.00 248.00 Sqm 4,997.70 12,39,429.60

secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing

11.05 21.80 weather silicon sealant over backer rod of approved quality as per architectural drawings and

direction of Engineer-in-charge complete

21.8.1 Upto 5 mm depth and 5 mm width 302.00 10.00 312.00 metre 96.75 30,186.00

Providing and fixing aluminium casement windows fastener of required length for aluminium

windows with necessary screws etc. complete

21.15.1 Anodized (AC 15) aluminium 1.00 2.00 3.00 Each 89.40 268.20

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc.

complete as per direction of Engineer-in-charge

21.16.1 Anodized (AC 15) aluminium 1.00 2.00 3.00 Each 107.90 323.70

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing Automatic Sliding door operator, compliant with future European standards and

produced according to the guidelines for power-operated windows, doors and gates, BGR 232, the

UVV and the VDE regulations. TÜV design tested for durability of 1 Million Cycles, tested according

to the low voltage guidelines, fulfils DIN 18650 standards, for framed glass door application with ST-

Flex Profiles Systems, modular design including internal cover and with 10 mm toughened glass

for 2 Nos sliding door panels and 2 Nos fixed panels, both sliding & fixed panels with ST-Flex

framed profile system with Interlocking Seals. Operator & Frame Finish should be Silver Anodized

E6/C0, with operator dimensions (H x D) : 100 x 180 mm and of length as required to suit the

opening size given below.

Automatic Sliding door operators are of very sturdy design with self balancing Panel suspension

system and with Anti-Jump fitting. The track profile should be separate from the main profile for

enabling reduction in vibration insulation, With backplate for easy Installation. Microprocessor-

controlled control unit, Self-learning, with adjustable parameters for opening and closing speed,

hold-open time and opening and closing force, reversing when obstruction is encountered, with

SMPS, Class of protection IP 20. Activators- Nemo Motion + Nemo Dual (Safety& Motion) with EM

Lock - Fail Safe, Program Switch with Key. ES 200 Easy, Max Panel Weight Carrying Capacity of 2

X 100 Kgs, Clear Passage Width = 700 - 2000 mm, Max Clear Passage Height = 3000 mm. The

system shall have constant power supply 230V+ 5%, 50Hz, AC.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring

11.09 21.18 type fixing arrangement and making necessary holes etc. for fixing required door fittings, all 21.00 21.00 Sqm 5,325.90 1,11,843.90

complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long

with SS screws etc .complete as per direction of Engineer-in-Charge.

21.12.2 Powder coated minimum thickness 50 micron aluminium tubular handle bar 18.00 18.00 each 631.55 11,367.90

Providing and fixing Toilet cubicles with the following specifications:

Thickness of Compact Laminate : 18 mm

Color of HPL Boards: As approved by Engineer-in-charge

Size of Cubicle : As per drawing Door Size : 1995mm

(H) x610mm (W) Divider Size : 1995mm (H) Overall Height Of Cubicle : 2100mm (Including boom

Gap of 100mm) Accessories: Standard - Merino Make Stainless Steel - 304Grade accessories)

a) SS "U" Channel

b) SS "F" channel

d) SS Privacy Thumb turn c/w Occupancy Indicator

e) SS Door Knob

f) SS Hinges with Cover

g) SS Shoe Box Leg 18mm - 316 Grade

h) Rubber Lining for Groove

i) S.S.Screws 304 G & P .V.C Wall Plugs

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and fixing Modular Railing comprising of the following:

01. Top Adaptors (Neck Type) for Flat- 05 Nos.

02. Rod Holder for Flat-15 Nos.

03. Articulated Rod Holder-03 Nos.

04. End cap for Ø50mm x1.6 thk SS Barrier-02 Nos.

05. Mid sleeve (Short)-01 No.

06. Universal Elbow-01 No.

07. 10x50 mm AISI 304 Grade S.S. Top mounted Flat

Baluster ,100 x 100 x 8mm Thick 202 Grade base Plate-05 Nos.

08. 16mm X 1.2mm thick X 1nos AISI 304 Grade S.S

Horizontal Members (3600mm Length)-04 Nos.

09. Round Pipe for Ø50mm x1.5mm Thick handrail (3600mm Length)-02 Nos. including installation,

freight & loading & unloading at Chandigarh.

Supply & Installation of Aluminum profile with top & bottom profiles of size 82mm x 38mm in Natural

Anodized / Black finish. Partition sides to be fixed with mullion and it's covers should be easily

accesible while removal of glass, if & when required. Glass to be fixed with suitable EPDM gaskets

for insertion of combination of 10mm thick clear toughened glass + 58 to 62 mm Air Gap + 12 mm

thick clear Toughened Glass. Glass should not placed directly on profiles for giving more strength. It

should be placed on aluminium spacer profiles and spacers should be covered with cover profiles.

11.13 MR Partition Glass joineries consists of two-way Polycarbonate I-profiles, 90 Degree Polycarbonate L- 225.00 225.00 Sqm 25,247.00 56,80,575.00

Junction and Polycarbonate T-Junction profiles. Polycarbonate profile joineries to be fixed with

double sided adhesive tape & profiles to be inserted in the joint instead of sealing it with sealants.

Polycarbonate profiles to be used to give continuity glass effect. Hardware for fixing profiles to be

used as per manufacturer standard. Profile & hardware should be from same brand to give end to

end solution. Costs should be inclusive of necessary Hardware for fixing of profiles & installation

Providing & Fixing of Partition System Double Glazed Stile Door having size of 75x55mm with door

profile GD-75T+ i.e.. 6063-T6 Virgin grade duly Anodized Aluminium Door Sections having sizes of

11.14 MR 75x30x1.5mm thick, 2 Layers of 6 mm toughened Glass including Geze make Door Closer 9.00 9.00 Sqm 49,036.00 4,41,324.00

TS3000V, 5nos Flush Hinges, SS Offset D type Pull Handle 25 x 450mm with narrow Stile mortise

Dead lock, Door Seal & Gaskets

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing & fixing of Window Blinds as per the approved sample in required shade and style

consisting, of Roller Blinds comprising of optima screen Fabric comprising of 22% polyester, 78%

PVC, Fabric weight 460-480G weight per sqm, Thickness 0.67 mm, Yarn count 18-19/cm, having

fire resistance standard – NFPA 701-89 small testing ISO-5659-2. The tear resistance should be

complying to ISO4674 & breaking resistance – ISO 5081. GREENGUARD NFPA701 ceritified

fabric. The control clutch drive unit engineered heavy duty chain drive pulley operating system

consisting of gear clutch housing and locking plug containing minimum 6 ribs and inserted at

minimum of 37mm into roller tube. It is self lubricating Exclusive clutch with safety pins for secure

bracket installation and unlocking pin for quick manual removal. Universal clutch is most convenient

for large windows down to the smallest windows. It shall be driven by a ball chain pulley with ball

chain and can be positioned at Right hand or Left hand side of the shade. Clutch gear ration 1.75:1

for reduced operating force on larger blinds. Tube bearing plug idler Exclusive self lubricating spring

loaded plastic bearing end plug with positive locking wheel allows for adjustment and provides for a

secure installation and removal of shade. Tube bearing plug contain minimum 6 ribs and inserted a

minimum of 37mm into roller tube. Mounting hardware brackets universal brackets including end

plug bracket with lock down retainer device. Brackets finish of powder coated metal installation

brackets made of stamped and hardened steel with 46mm projection for wall, ceiling and side fitting

with screws and end cap covers.

Roller tube circular-shaped aluminum tube extruded from alloy 6060 and temper T66 – EN755 of

37mm inside diameter and outside diameter 40.2mm extruded tube to have a 1.6mm wall thickness

with standard anodized natural finish. Heavily reinforced with minimum six internal ribs providing

additional tensile strength and allows for secure placements of clutch and end plug. Bottom rail flat-

shaped extruded aluminum from alloy 6060 and temper T66 – EN755 of dimension 13mm * 30mm

and wall thickness of 1.5mm and weight of 390g/m. Rail standard finish of powder coat white color

and provided cover. Ball chain shall be 2mm diameter cord with 4.5mm diameter acetal balls

molded coaxially to it on 11.8mm pitch to form an endless ball chain. It is used for raising or

lowering action of the shades. Plastic parts all plastic components are UV-stable compounds

available white colour.

Total Aluminium Works : 24,74,288.25 1,10,75,609.00

12.00 25.00 Structure Glazing

Providing and supplying aluminium extruded tubular and other aluminium sections as per the

architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or

T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA

12.01 25.10 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes 3936.00 3936.00 Kgs 414.30 16,30,684.80

cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded

aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium

extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system

12.02 25.20 of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all

heights and all levels, including

(a) Structural analysis & design and preparation of shop drawings for the specified design loads

conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind

pressure without any failure), including functional design of the aluminum sections for fixing glazing

panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws,

toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop

(barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure

equalisation & drainage and protection against fire hazard including:

(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5

brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for

achieving perfect verticality and fixing structural glazing system rigidly to the RCC/

masonry/structural steel framework of building structure using stainless steel anchor fasteners/

bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel

grade 316, of the required capacity and in required numbers.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather

silicone sealant compatible with the structural silicone sealant of required bite size in a clean and

controlled factory / work shop environment, including double sided spacer tape, setting blocks and

backer rod, all of approved grade, brand and manufacture, as per the approved sealant design,

within and all around the perimeter for holding glass

(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes,

shapes and profiles, as required as per the site conditions, to seal the gap between the building

structure and all its interfaces with curtain glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make

it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at

bottom (if required), making necessary holes of required sizes and of required numbers etc.

complete. This item includes cost of all inputs of designing, labour for fabricating and installation of

aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including

wastages etc., enabling temporary structures and services, cranes or cradles etc. as described

above and as specified.

The item includes the cost of getting all the structural and functional design including shop drawings

checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the

cost of all mock ups at site, cost of all samples of the individual components for testing in an

approved laboratory, field tests on the assembled working structural glazing as specified, cleaning

and protection till the handing over of the building for occupation. In the end, the Contractor shall

provide a water tight structural glazing having all the performance characteristics etc. all complete

as required, as per the Architectural drawings, as per item description, as specified, as per the

approved shop drawings and as directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium

section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire

mesh shall be paid for separately under relevant items under this sub- head. However, for the

purpose of payment, only the actual area of structural glazing (including width of grooves) on the

external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of

structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National

Accreditation Board for Testing and Calibration Laboratories), Department of Science &

Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide

the necessity of testing on the basis of cost of the work, cost of the test and importance of the work.

Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab

or any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits

labs as per ISO/IEC 17025

1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as

per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a

range up to 2000 ml

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a

range upto 2000 m

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design

wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test,

Tests to be conducted on site

6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml 394.00 394.00 Sqm 3,510.50 13,83,137.00

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-

12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and

specified, comprising of an outer heat strengthened float glass 6 mm thick, of approved colour and

shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat

12.03 25.30 strengthned clear float glass 6 mm thick, spacer tube 12 mm wide, dessicants, including primary

seal and secondary seal (structural silicone sealant) etc. all complete for the required

performances, as per the Architectural drawings, as per the approved shop drawings, as specified

and as directed by the Engineerin-Charge. The IGUs shall be assembled in the factory/ workshop

of the glass processor.

(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For

payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the

grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm

Airgap + 6 mm Heat Strengthened clear Glass of approved make having properties as visible Light

transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to

(i) 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties 394.00 394.00 Sqm 3,718.70 14,65,167.80

of performance glass shall be decided by technical sanctioning authority as per the site

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at

site all accessories and hardwares for the openable panels as specified and of the approved make

such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless

12.04 25.40 steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, 20.00 20.00 Sqm 3,671.50 73,430.00

washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as

specified and as directed by the Engineer- in-Charge.

Providing, fabricating and supplying shadow box of required size and shape, for fixing in the

spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by

providing semi -rigid, inorganic, non-combustible fibre glass wool insulation 50 mm thick,

conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded

12.05 25.50 on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal 22.00 22.00 Sqm 2,159.65 47,512.30

thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of randomly oriented glass

fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet

backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened

monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of

approved colour and shade so as to match the colour and shade of the IGUs in the vision panels

etc. ,all complete for the required performances as specified, as per the Architectural drawings, as

12.06 25.60 per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For

payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of

grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

(Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent

(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, having

properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%,

light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 22.00 22.00 Sqm 2,450.15 53,903.30

K etc. . The properties of performance glass shall be decided by technical sanctioning authority as

per the site requirement.

Total of Structural Glazing Rs. 46,53,835.20 0.00

13.00 22.00 WATER PROOFING

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed

portions of W.C., kitchen and the like consisting of:

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS : 2645 in recommended proportions including rounding off junction of vertical and

horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing

compound in recommended proportion including rounding off junction of vertical and horizontal

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm

wide and pasted to each other with bitumen @ 1.7 kg/sqm)

Providing and laying integral cement based water proofing treatment including preparation of

13.02 22.7 surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing

compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab

including adjoining walls upto 300 mm height including cleaning the surface before treatment

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming

to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix

1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300

mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of

cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse

sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

charge including laying glass fibre cloth of approved quality in top layer of plaster and finally

finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for

curing and for final test. “All above operations to be done in order and as directed and specified by

the Engineer-in-Charge”:

22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm 2395.00 20.00 2415.00 Sqm 1,684.60 40,68,309.00

Providing and laying integral cement based treatment for water proofing on horizontal surface at all

depth below ground level for under ground structures as directed by Engineer-in-Charge and

consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a

25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) including applying of twice ( at

base and top of mortar ) cement slurry @ 2.2kg/m2 (each time) mixed with water proofing

compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling

course to be paid separately). Joints sealed and grouted with cement slurry mixed with water

proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand)

mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone

aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and laying integral cement based treatment for water proofing on the vertical surface by

fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing

compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum)

between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed

13.04 22.2 with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1

cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing

compound in recommended proportion complete at all levels and as directed by Engineer-in-charge

Providing and applying of swellable type water stop tape, 19 mm x 25 mm thick in linear metre

(expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining

walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning

the surface, one coat of required primer for swellable water stop tape shall be applied throughout

13.05 22.26 the length of the joint @3.78 litre per 240 running metre. Over the primed surface swellable type 10.00 388.00 398.00 Metre 573.45 2,28,233.10

water stop tape shall be placed. The work shall be carried out all complete as per specification and

the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10

years against any leakage.

Total Water Proofing work : 47,57,348.00 0.00

14.00 16.00 ROAD WORK

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after

excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road

14.01 16.1 roller including making good the undulations etc. and re-rolling the sub grade and disposal of 1644.00 1644.00 Sqm 218.90 3,59,871.60

surplus earth with lead upto 50 metres.

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XO) on 150 mm thick sub grade of

compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150

14.02 11.55 mm thick Jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. 250.00 250.00 Sqm 1,708.10 4,27,025.00

all complete as per direction of Engineer-in-charge.

Construction of granular sub-base by providing close graded Material conforming to specifications,

mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all

14.03 16.8 leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared

surface and compacting with vibratory power roller to achieve the desired density, complete as per

specifications and directions of Engineer-in-Charge.

16.78.3 With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20 97.00 97.00 Cum 2,808.55 2,72,429.35

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways,

using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm

nominal size in appropriate proportions as per approved & specified design criteria, providing dowel

bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically

by using needle and surface vibrators, levelling to required slope/ camber, finishing with required

14.04 16.4 texture, including steel form work with sturdy M.S. channel sections, curing, making provision for

contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove

cutting machine, providing and filling joints with approved joint filler and sealants, complete all as

per direction of Engineer in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to

be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per

design mix is payable/ recoverable separately.

16.43.1 Cement concrete prepared with batch mixing machine 47.00 47.00 Cum 10,529.35 4,94,879.45

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after per cm

making the joints dust free with high pressure air jet cleaners, all complete as per direction of the depth per

14.05 16.45 Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound 155.00 155.00 cm width 5.30 821.50

impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board per metre

and IS: 1834 for hot sealing bitumen compound grade A.) length

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion

14.06 16.46 joints in roads / pavements all complete as per direction of the Engineer-in-Charge.

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion per cm

joints in roads / pavements all complete as per direction of the Engineer-in-Charge. depth per

Construction of dry lean cement concrete sub base over a prepared sub grade with coarse and fine

aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate

cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications,

cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during

14.07 16.8 trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching 16.00 16.00 Cum 4,148.65 66,378.40

plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10

tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge.

Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement

concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1

cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except

14.08 16.69 at sharp curve shall not to more than 5mm), including making drainage opening wherever required

complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be

measured for payment).

(Precast C.C. kerb stone shall be approved by Engineer-in-charge). 50.00 50.00 Cum 10,117.60 5,05,880.00

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre

openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of

wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T.

reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including

14.09 16.53 necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in- 1251.00 1251.00 metre 375.80 4,70,125.80

charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength

of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C.

blocks shall be paid separately)

Total Road Work: 25,98,751.85 0.00

15.00 23.00 RAINWATER HARVESTING

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit,

15.01 23.5 in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in charge. 29.00 29.00 Cum 1,509.80 43,784.20

Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit,

15.02 23.6 over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per 29.00 29.00 Cum 1,538.25 44,609.25

direction of Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in

15.03 23.7 required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in- 29.00 29.00 Cum 1,538.25 44,609.25

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel

15.04 23.8 fine/medium/coarse, in required grading & size as per actual requirement, all complete as per 29.00 29.00 Cum 2,024.50 58,710.50

direction of Engineer-in-charge.

Replacement of M.S. foot rests in manholes including dismantling concrete blocks and fixing with

15.05 19.17 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate

20 mm nominal size):

15.06 19.19 Providing and fixing in position precast R.C.C. manhole cover and frame.

19.19.3.1 Circular shape 560 mm internal diameter 12.00 12.00 each 1,675.70 20,108.40

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: CIVIL

Quantity Rate DSR Amount NDSR Amount

S No DSR 2023 Description of Item Total Qty Unit

Building External Rs. Rs. Rs.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS:

2800 (part I), including collecting samples from different strata, preparing and submitting strata

15.07 23.1 chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries

required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below

23.1.2 Rocky strata including Boulders

Supplying, assembling, lowering and fixing in vertical position in bore well Unplasticised PVC

medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour

15.08 23.4 charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and

approved quality

19.19.1.1 Rectangular shape 600x450 mm internal dimensions 12.00 12.00 each 1,437.65 17,251.80

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with

bricks in cement mortar 1 :4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x61 O

mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover

23 kg and weight of frame 15 kg), R.C.C. top slab with 1: 1.5:3 mix (1 cement : 1.5 coarse sand : 3

15.10 19.3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 fine sand : 10 graded

stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1 : 3 ( 1

cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed

concrete etc. complete as per standard design:

Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

19.30.2 With common burnt clay non-modular bricks of each class designation 7 .5 6.00 6.00 each 8,150.50 48,903.00

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with

15.11 19.32 bricks and S.W. drain pipe 100 mm diameter, 1.Bm long complete as per standard design.

19.32.1 With common burnt clay non-modular bricks of class designation 7.5 1.00 1.00 each 26,861.90 26,861.90

Total Rain Water harvesting Work 10,02,474.50 0.00

Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR E&M TOTAL AMOUNT TOTAL AMOUNT

DSR E&M TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT QTY RATE

2025 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in

1.10 surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR

A.1 PVC insulated copper conductor single core cable etc. as required

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS/HFFR

1.55 PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS/HFFR PVC insulated

A.2 copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC

A.3 1.12 conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. Metre 6840 373.00 2551320.00

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc.

1.24.4 3 pin 5/6 amp socket outlet Each 2 136.00 272.00

1.24.5 6 pin 15/16 amp socket outlet Each 2 219.00 438.00

A.5 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. Each 10 47.00 470.00

1.27 Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC

A.7 1.11 conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single Each 10 1803.00 18030.00

core cable etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular

socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A

modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A

A.10 1.56 modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). Each 56 757.00 42392.00

Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket

outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in

surface/ recessed medium class PVC conduit as required.

B.1 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 10 482.00 4820.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 180 1078.00 194040.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 180 1454.00 261720.00

11.1 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

X 35 sq. cable of 1.1 KV grade as required.

26 Digitally signed by AKSHIT

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium Conductor Cables :

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 /

IS:1554 part-1 respectively & ISI marked.

C.2 3.5 C x 95 Sqmm XLPE cable

(c ) 3.5 C x 70 Sqmm XLPE cable RM 50 680.00 34000.00

(d) 3.5 C x 50 Sqmm XLPE cable RM 50 510.00 25500.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 50 378.00 18900.00

(g) 4 C x 16 Sqmm XLPE cable RM 500 210.00 105000.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper conductor armoured cable of 1.1 KV grade conforming to

C.3 MR IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 250 1446.00 361500.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 100 2253.00 225300.00

(c ) 3.5 C x 35 Sqmm XLPE copper cable RM 50 2686.00 134300.00

(d) 3.5 C x 50 Sqmm XLPE copper cable RM 50 3224.00 161200.00

C.4 10.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation,

sand cushioning, protective covering and refilling the trench etc as required.

10.1.2 Above 35 sq. mm and upto 95 sq. mm Meter 100 475.00 47500.00

10.1.3 Above 95 sq. mm and upto 185 sq. mm Meter 100 497.00 49700.00

10.1.4 Above 185 sq. mm and upto 400 sq. mm Meter 200 564.00 112800.00

D.1 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. Each 100 14.00 1400.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the

D.2 existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with

2.4 tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/

D.4 RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 8 9081.00 72648.00

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current

30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper

D.6 2.3 bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

2.3.3 12 way, double door Each 2 2871.00 5742.00

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc.

1.24 as required.

1.24.6 Telephone socket outlet Set 54 168.00 9072.00

1.24.7 TV antenna socket outlet Set 2 168.00 336.00

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected

with PVC sheath in the exisitng surface/recessed steel/ PVC conduit as required

27 Digitally signed by AKSHIT

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good

E.3 the same in case of recessed conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing

surface/ recessed steel/ PVC conduit as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding

E.5 1.25 modular plate etc. as required. Each 1 402.00 402.00

Installation, Testing and Commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS/HFFR PVC

insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning

etc. as required.

E.8 1.51 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. Each 16 260.00 4160.00

Brush Less Direct Current (BLDC) Fan with Remote: Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current

(BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper

winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD

E.9 9.1 (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin,

nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply

Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and

earthing etc. as required.

9.1.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Each 1 2882.00 2882.00

E.10 MR Supply of Exhaust Fan 300 mm Each 16 3500.00 56000.00

Providing and fixing M.S. Fan clamps of 16 mm dia M.S. bar, bent to shape with Hooked ends in R.C.C. slabs or beams during laying, including painting

the exposed portion of loop, all as per standard design complete

Providing and fixing circular/Hexagonal G.I. Box for ceiling fan clamps, of internal dia 140 mm, 73 mm height, top LID of 1.5 mm thick G.I. sheet with its

E.12 DSR 10.18 top surface hacked for proper bonding, top LID shall be screwed into the G.I. box by means of 3.3 mm dia rounded screws, one lock at the corners. Each 1 220.65 220.65

Clamps shall be made of 12 mm dia M.S. bar bent to shap as per standard drawing.

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non-

Plenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4

Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC

E.13 39.18 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be <

45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required.

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with required suitable number of GI couplers for joining

raceways and fixing GI brackets and all accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 20 1738.00 34760.00

(b) 225mmx38mm(GI) - 3 compartment Mtr 20 1420.00 28400.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at the intersection of raceways supplied completely with

MR base and cover plates, height adjustable junction box 65- 90 mm including all accessories ss plate of 3mm thick complete in all respect as per the

directions of engineer in charge

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

F.2 5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. MTR 200 1246.00 249200.00

F.3 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. MTR 200 287.00 57400.00

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 1000 84.00 84000.00

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I.

base plate including holes etc. complete as required.

F.6 6.2 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. Each 4 422.00 1688.00

28 Digitally signed by AKSHIT

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering

etc as required.

F.8 6.6 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) Meter 160 148.00 23680.00

F.9 6.70 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) Meter 240 238.00 57120.00

G PANEL BOARDS

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and commissioning the following sheet steel cubicle type panels

fabricated from 1.6mm thick CRCA sheet, dust and vermin proof, outdoor type double door with canopy, TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters and accessories, inter-connections, bonding to

earth, powder coated painting and marking as specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 400 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all

TPN aluminum bus bars of minimum of 500 Amps capacity with heat shrinkable colored sleeves and I/C DMC/SMC bus bars supports at required

intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 10 Nos.

(b) 40 Amps, TPN, MCB - 10 nos

Panel complete as above Each 1 425000.00 425000.00

G PANEL BOARDS

Floor Panel/ UPS Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and commissioning the following sheet steel cubicle type panels

fabricated from 1.6mm thick CRCA sheet, dust and vermin proof, outdoor type double door with canopy, TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters and accessories, inter-connections, bonding to

earth, powder coated painting and marking as specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 160 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all

TPN aluminum bus bars of minimum of 200 Amps capacity with heat shrinkable colored sleeves and I/C DMC/SMC bus bars supports at required

intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 Nos.

(b) 40 Amps, TPN, MCB - 4 Nos

Panel complete as above Each 4 225000.00 900000.00

H SAFETY ITEMS

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2 mm thick, and vitreos enamelled white on both sides and

with iscription in single red colour on front side as required

29 Digitally signed by AKSHIT

Online UPS- Input supply: Three Phase, Output supply: Three Phase- Supplying, installation, Testing & Commissioning of following capacity at full load

(Unity Power Factor) at operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot

swapable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with

N+1 modules (N denotes total number of modules required for rated capacity).

The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA

of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for

manual bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence correction. The

UPS systems offered are to be of the latest technology with Digital Control icroprocessor based for reliable operation using Insulated Gate Bipolar

Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing and inspection

process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while

operating on battery mode and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5%

at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be included to limit the

input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1), however UPS shall be suitable to

take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output

voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1

meter distance, protections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over current, short circuit protection,

H.2 26.2 battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204,

EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. Communication RS232/ RS485/ SNMP port open protocol

for BMS integration, all hardware & software for iOT Communication as per approved by Engineering in charge. Required battery racks and

interconnecting copper conductor cables of suitable size and connectors and all required accessories are inclusive of the cost). This system must

provide a means for logging and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if

one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in compliance IEC 62040-

1,2 & 3, IS: 16242 and CPWD Specification. Display Panel (minimum) (In-build 5 inch or more LC Display/ LED) to display : a) Input: Voltage, current,

Frequency. b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current. d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage. f)

Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to 3000 events like: Over

temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data:

No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load /

UPS Fault /Battery charging and discharging, overload, battery voltage and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS

Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over

Temperature. The UPS should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location etc

a 26.2.2 20KVA (Each Power module shall be ≤ 10 KVA) Nos. 2 341772.00 6,83,544.00

b 26.2.4 40KVA (Each Power module shall be ≤ 10 KVA) Nos. 2 599469.00 11,98,938.00

Total of Electrical items 10059801.65 4429800.00

30 Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: HVAC

S No Description Unit Quantity Rate DSR Amount NDSR Amount

VRF OUTDOOR UNIT: Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable

Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin

Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules,

microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration

Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate

at different speed with respect to load. The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and

CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of

the rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply

1 31.3 and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser

should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water

dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal

Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024

as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr

ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)

For Cooling or Heating or Both

VRF INDOOR UNITS: Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit

equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower,

multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan,

necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The

2 31.8 Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust

air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C

DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum capacity Single way wall/corner VRV/VRF Cassette Type

Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz

3 31.6 AC supply,complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals.

The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be

at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

INDOOR UNIT Supply, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan /dynamically balanced

blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz

4 31.4 AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals.

The system shall be capable to adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will be

at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Double Skinned VRF DX AHU

31 Digitally signed by AKSHIT

Supply, Installation, Testing and Commissioning of Double skin floor mounted air handling units complete with thermal break

profile ,Mixing box, filter section, Dx coil of copper tube and aluminium construction, blower, motor, forward Curve fan, Limit

switch and related wiring, canvas at unit out let,mounted on Spring isolaters & coil size shall be selected for a maximum face

velocity of 500 FPM etc.10 micron filter as per the enclosed specifications.motor shall be suitable for 415+/-10% volts, 50 cycles,

5 3 phase ac supply with starter panel, thermostat and related cabling etc.

Insulated stainless steel drain pan under coil section, filter section comprising of 10 & 5 microns combination prefilter at suction

side on universal frame and and 3 micron & 0.3 HEPA filters at discharge side, mixing box along with RA and FA, Blead off

dampers with handles suitable for manual and auto operation etc.

MR AHU - 24 TR capacity, Dehumidified Air Qty 14500CFM (90% Return Air + 10% Fresh Air), 150mm Total Static pressure with

suitable High efficency motor along with 8 row coil

b EXPANSION KIT FOR AHU

Supply, Installation, testing and comissioning of expansion and control kit for the operation of AHU. Nos. 5.0 35122.00 1,75,610.00

c Corded Self Diagnostic Type Remote Controllers

Supply, Installation, Testing & Commissioning of Corded Wall Mounted Type Self Diagnostic Type Digital Programmable

Individual Remote Controllers of latest generation for setting required temperature for various Indoor Unit.

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer

6 31.13 (OEM) make as of ODUs and IDUs

b 31.13.2 Outdoor Multi Joint Nos 10 8,098.00 80,980.00

REFRIGERANT PIPING:

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger

7 31.14 supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required:

a 31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 270 256.00 69,120.00

b 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 480 346.00 1,66,080.00

c 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 270 487.00 1,31,490.00

d 31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 480 615.00 2,95,200.00

e 31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 200 739.00 1,47,800.00

f 31.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 200 904.00 1,80,800.00

g 31.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 100 1,068.00 1,06,800.00

h 31.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 100 1,157.00 1,15,700.00

i 31.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 50 1,222.00 61,100.00

j 31.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 50 1,286.00 64,300.00

k 31.14.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 50 1,322.00 66,100.00

l 31.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 50 1,368.00 68,400.00

8 MR 300x75mm outdoor cable tray with cover (hot dip galvanized) Metre 500.00 1,439.00 7,19,500.00

DRAIN PIPING For VRV HVAC

9 Providing and fixing of uPVC/cPVC/PVC drain pipe

CONTROL CABLING

Supplying, receiving, storing, laying, effecting proper connections, testing and commissioning of the following sizes of 1.1 KV

grade PVC insulated copper conductor unarmoured stranded control cable complete as required.

a MR 2C x 1.5 mm² Cu (Communication cable from ODU to IDU for VRF units) Metre 660 274.00 1,80,840.00

32 Digitally signed by AKSHIT

Supply, Installation, Testing & Commissioning of Silent type circular /rectangular inline fans for exhaust air complete with sheet

metal casing, 25mm thick acoustic insulation, direct driven centrifugal fan, motor with proper protection and inspection door.

Fan shall be suitable for operation on 220+6 % volts, 50 Hz,1 phase AC power supply. Flanges to be provided on both sides to

facilitate duct connections. Fan shall be installed as shown in the drawings and will be of following characteristics:

11 All single phase inline fans shall be provided with factory fitted speed regulators. All Fans Should be complete with Plug Top &

MR necessary power cable.

Fans shall have low noise level in rage of 35-40dBA @3m and shall be suitable for indoor installations.

a 200 CFM S P of 13-14 for Toilet Nos. 5 6500.00 32500.00

b 500 CFM S P of 13-14 for Toilet Nos. 4 9500.00 38000.00

Supply, Installation, Testing and Commisioning of powder coated SS factory fabricated flat oval ducting with fittings and gripple

wire supports. The factor of gripple support to suit the duct weight with necessary anchor fastners and hook arrangements with

suitable thickness etc., confirming to SMACNA standards. Duct should be fabricated by using CNC machines including

12 neccesary civil works as per site condition. The joints shall be seamless and ducts joining shall be done using rivets only. The

ducts shall be powder coated with RAL color as per architect approval. The complete ducting cost shall be including 9 mm thick

MR nitrile rubber thermal with insulation internally. The insulation used for factory lining shall be of self adhesive type.

a Thickness 0.63 mm sheet SQM 120 2150.00 258000.00

b Thickness 0.80 mm sheet SQM 100 2528.75 252875.00

c Thickness 1.00 mm sheet SQM 80 2925.00 234000.00

d Thickness 1.25 mm sheet SQM 60 3625.00 217500.00

Diffusers & Grills

Supplying, Fixing, installation, testing and commissioning of powder coated extruded aluminium Supply Air Grills with aluminium

volume control dampers in confirmation to SMACNA/IS and as per specifications complete etc. as required.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers

complete in confirmation to SMACNA/IS and as per specifications complete etc. as required.

Supplying, Fixing, installation, testing and commissioning of supply air diffusers of powder coated aluminium with aluminium

volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications

Supplying, Fixing, installation, testing and commissioning of Return air diffusers of powder coated aluminium without volume

control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc.

Supply, Installation, Testing of 125mm deep antivibration flexible joints at the outlet of air handling units/ductable split units//inline

17 MR fans. Flexible connections shall be constructed using imported fire retardant fabric with extruded aluminium frame/flange on both RM 50 1540.00 77000.00

sides of approved make.

Supply, Installation, Testing and Balancing of linear slot diffusers as per the approved shop drawings and specifications. Each

MR slot shall be 25mm wide. The diffuser face shall be a one piece extrusion so there are no visible joints. Slot diffusers shall be

a 3 slot/2slot, powder coated extruded aluminium diffusers of approved colour & shade. SQM 10 13372.00 133720.00

Supply, Installation and Testing of Bird Screens with GI wire mesh to be installed at the suction of fresh air/discharge of Exhaust

air as per the specifications and shop drawings. Sample of bird screen to be got approved from consultants and Clients prior to

Supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell Nitrile rubber (Class "O")

insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3

Supplying and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of

32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue

33 Digitally signed by AKSHIT

Supplying, Fixing, testing and commissioning of fire dampers of minimum 90 minutes fire rated in supply air duct/main branch

and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so

22 30.2 as to close the damper in the event of power failure automatically and open the same in case of power being restored. The

spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire

signal and, in confirmation to IS and as per specifications complete etc. as required..

23 MR Supply and fabrication of double layer canvass connection (Fire retardent cloth for end connect of AHU to reduce the vibration) SQM 5 10177.50 50887.50

Isolator Switch with Metal Enclosure for ODU (IP-65) (The unit shall come with actual capacity of VRV Out door unit for smooth

MR 80 / 100 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site

b Star Delta Panel for AHU Nos. 5 26461.50 132307.48

34 Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: LIGHTING FIXTURES

DSR E&M Reference

S No Description QTY Unit RATE DSR Amount NDSR Amount

Supply, Installation, Testing and Commissioning of recess deep inset COB LED Downlight luminaire made up of pure

polyster powder coated pressure die cast Aluminium housing with inbuilt heat sink to provide better thermal management to

enhance LED life. The luminaire should be equiped with the secondary optics of high efficiency white coloured reflector.

The luminaire should be available with multiple beam angle options of 38° and 60°.LM 80-08 compliant ceramic / aluminium

base LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Citizen should be provided. LEDs used in

the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be

provided. The luminaire should be IP20 rated. The LEDs used should be with CCT of 4000 K and CRI of Minimum 80. LED

1 MR Driver shall be non-integrated type, Isolated, Constant Current operated driver with range 100-300V AC. Driver Efficiency >

84% & 2.0KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 15%

should be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of

India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.

Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) :

Supply, Installation, Testing and Commissioning of 4 feet, ceiling or wall mounted, SMD LED batten of 20W LED luminaire

with System efficacy of 120 lm/W and 2400 system lumens, operating in ambient temperature of 0⁰C to 45⁰C . Luminaire

shall be made up of extruded anodised aluminium housing with polycarbonate high transmissivity diffuser, ensuring uniform

illumination glare free lighting. LEDs used in the product complies with IEC 62471 for Photo-biological safety. With

screwless design, luminaire is with IP40 protection with stainless steel mounting clamps. LM 80-08 compliant LEDs from

reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply with L70

life of 50000 burning hours tested at maximum current .The LEDs used shall be with CCT of 5700 K and CRI of minimum

MR 80, with MacAdam CCT binning < 5. Isolated, Constant Current with range 150-270V AC with internal surge protection of

2kV Driver of Efficiency > 85%, Power factor of minimum 0.95 and total harmonic distortion (THD) of less than or equal to

10% shall be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of science of

govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.

Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) :

LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy >135

lm/Watt): Supplying, Installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die

cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-

270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per

IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI>70, under

voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per

the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical

circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80

3 8.14 extrapolation IES TM-21-11 report, CCT 3000°K /4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation

Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of

relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated

copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen

efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be

submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management:

heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

# Public Digitally signed by AKSHIT

Supply, Installation, Testing and Commissionin of Integral, SMD 4x1 Backlit LED Panel, IP 20, 30W LED recessed

mounted fixture with system efficacy of minimum 100lm/W and system lumen output of minimum 3000lm, operating in

ambient temperature of 0⁰C to 45⁰C at 50Hz frequency. Luminaire shall have CRCA housing coated in white (RAL9016)

with translucent HET diffuser for uniform illumination and wider light distribution. LEDs used in the product shall comply with

IEC 62471. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should

be provided. The LED shall comply with L70 life of 50000 burning hours tested at maximum current. The LEDs used should

be with CCT of 4000 K and CRI of Minimum 80. LED Driver shall be Isolated type, Constant Current topology driver with

4 MR proper heat sink for heat dissipation suitable to operate in input voltage range of 140V to 300V (nominal rated voltage – 252 Nos 4025.00 1014300.00

240V) with 4KV internal surge protection, Power factor of minimum 0.95 and total harmonic distortion (THD) of less than or

equal to 10% should be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of

science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above

parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS15885

Supply, Installation, Testing and Commissionin of 30W, suspended by 1.5m suspension wire, 4 feet linear, IP20, SMD LED

luminaire with system efficacy of 110 lumen/watt and system lumen output of 3300 lumen, operating in an ambient

temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, luminaire shall have extruded aluminium housing in white with

high efficiency translucence diffuser and must have provision for end to end seamless connectivity. EMC package of

wattage of 0.2-0.5 W LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. LM 80-08

compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/Osram/Seoul should be provided. The LED

shall comply with L70 life of 50000 burning hours tested at maximum current. The LEDs used should be with CCT of 4000

K and CRI of Minimum 80, with MacAdam CCT binning ≤3 mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED

5 MR Driver shall be Isolated type, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate 54 Nos 4600.00 248400.00

in input voltage range of 140V to 300V (nominal rated voltage – 240V) with 3KV internal surge protection, Power factor of

minimum 0.95, driver efficacy of minimum 85% and total harmonic distortion (THD) of less than or equal to 10% should be

integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM

79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to

Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS

16108 : 2012. Dimension: 1205 X 51 X 85mm, weight: 2.5Kg

Supply, Installation, Testing and Commissionin of 1200mm dia Pendent Mounted Ring LED. Fixture to be made of

extrusion Aluminum housing in white finish with HET plastic diffuser. LED Used shall be SMD type with Minimum system

Lumens 5100 @60W & efficacy 85lm/W,Life of fixture : 50000 burning Hrs. @ L70 Lumen maintenance, CCT of

4000/5700K (SDCM<=3), CRI Ra >=80, PF >0.95, THD<10%, operating Voltage Range of 150-270 V AC. Minimum

6 MR Internal Surge Protection 2.0KV. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of 4 Nos 33235.00 132940.00

India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Both the

fixture and Driver should have separate BIS approval. Luminaire should have RoHS, EMI EMC as per IEC 61547, CISPR

# Public Digitally signed by AKSHIT

Supply, Installation, Testing and Commissionin of 45W LED Decorative Post Top type luminaire with System efficacy of

100 lm/W (4500 lumens), suitable for external poles of dia. 65mm to 75mm. Luminaire shall be made up of pure polyster

power coated RAL7021 pressure die cast Aluminium housing with Polycarbonate Fresnel lens of symmetrical or street

optics of same make. All external hardwaremust be of SS304 grade. LM 80-08 compliant LEDs of EMC/ceramic package

from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. LEDs used in the product

shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.

Luminaire shall be with IP66 and IK10 protection. The LED shall be compliant with LM80-08 standard with L70 life of 50000

Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The

LEDs used should be with CCT of 4000/5700 K, CRI of Minimum 70 and SDCM <5. LEDs must be driven at max 70% of

the rated current. MCPCB with Aluminium core and copper thickeness of 35 micron to be used for LED mounting.LED

7 MR Driver shall be silicone potted, Integrated type, Isolated, Constant Current with range 150-300V AC. Driver Efficiency > 85% 20 Nos 8625.00 172500.00

& 4 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10%

should be integral to the luminaire. LED driver should have CISPR 15 / EN 55015 compliance to limit for radio disturbance

characteristics. LED driver should have CISPR 15 / EN 55015 compliance to limit for radio disturbance characteristics.

Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM79 and LM80 reports

need to be submitted from a NABL/UL accredited lab to verify above parameters. Luminaire should have Dark Sky

Certification to avoid sky glow and light pollution. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 :

2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012 should be there. Dimension: Dia Ø366 X 370mm

(+/-2mm), Weight: 2.2Kg

Supply, Installation, Testing and Commissioning of LED based bollard of squared cross section (83 X 83mm), housing

made up of extruded aluminium,sturdy and embossed brand name/logo name of manufacturer and optics made of milky

white PC diffuser with pattern. The fixture should have a minimum system efficacy of 55lumen/Watt and a minimum

system lumen output of 850 lumens and minimum system wattage of 15Watts.The fixture shall have a CRI of minimum 80.

The fixture shall be designed for a system life of 50,000 hours @70% lumen maintenance. Ingress Protection of IP65 (lamp

and gear Compartment) and Mechanical Impact Resistance Rating of IK10, CCT: 4000/5700K. The fixture driver should

8 MR have an operating voltage range of 140-280 V, surge protection of >=3KV, external surge protection 10KV, PF >0.95, 20 Nos 16100.00 322000.00

THD<10% & Driver efficacy >80% @full load and rated voltage. Ambient temp range: 0deg to 45deg C. The Drivers should

be a potted driver not a printed circuit board without casing, mounted inside the luminaire. The fixture should comply with

the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL . LM 79 and LM80 reports need

to be submitted from a NABL/UL accredited lab to verify above parameters. Height: 800mm & Weight including all

accessories should not be more than 2.2Kg.

Supply, Installation, Testing and Commissionin of LED based Spike light, housing made up of pressure die cast aluminum

Alloy with effective thermal management,sturdiness and embossed brand name/logo name of manufacturer and optics

made of surface mount reflector with toughened. The fixture should have a minimum system efficacy of 80lumen/Watt and

a minimum system lumen output of 640 lumens and maximum system wattage of 8 Watts.The fixture shall have a CRI of

minimum 80 and beam angle: 50-55deg. The fixture shall be designed for a system life of 50,000 hours @70% lumen

maintenance. Ingress Protection of IP67 (lamp and gear Compartment) and Mechanical Impact Resistance Rating of IK

>=07, CCT: 2700K. The fixture driver should have an operating voltage range of 100-270 V, surge protection of >=3KV, PF

>0.9, THD<10% & Driver efficacy >80% @full load and rated voltage. Ambient temp range: 0deg to 45deg C. The Drivers

should be a potted driver not a printed circuit board without casing, mounted inside the luminaire. The fixture should comply

with the parameters as per IS10322. Manufacturer shall have inhouse lab approved by NABL . LM 79 and LM80 reports

need to be submitted from a NABL/UL accredited lab to verify above parameters. Dimension: Ø115 X 158 X 93mm &

Weight including all accessories should not be more than 1.5Kg.

# Public Digitally signed by AKSHIT

Supply , Installation, Testing and Commissioning of 10W COB LED Downlight luminaire having 800 lumens, with cut-out

(Φ) dia of 54mm and height of 150mm, suitable for pendant mounting. Luminaire shall be made up of white powder coated

extruded Aluminium housing with inbuilt heat sink to provide better thermal management to enhance LED life.Suspension

wire of 1.5m should be supplied with the luminaire. The luminaire should be equiped with the secondary optics of high

efficiency reflector with clear glass to have precise light beam to cut down glare to UGR <19. LM 80-08 compliant LEDs

from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. LEDs used in the product

shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.

The luminaire should be IP20 rated. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at

10 MR maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used 221 Nos 4025.00 889525.00

should be with CCT of 4000 K and CRI of Minimum 80. LED Driver shall be Integrated type, Isolated, Constant Current

operated driver with range 140-280V AC. Driver Efficiency > 80% & 2KV internal surge protection, Power factor greater

than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Manufacturer shall have

inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from

a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967;

Supply , Installation, Testing and Commissioning of DALI dimmable and tunnable Suspened LED stretch fabric Luminaire,

with extruded aluminum housing delivering upto 3890lumen/sq m and it draws 55W/sq m maximum from standard 220-

240V AC supply . Fixture offers excellent light output, long source life, high CRI, and energy efficiency, in a beautiful, clean

plane of light. Industry-best quality of 80+ CRI and color consistency within a 3-step MacAdam ellipse provides a glare-free

direct view luminaire, and abundant, uniform daylight illumination evenly lit across the entire task surface.The diffuser shall

be Special translucent stretch fabric having good resistance properties -Flame retardant, Anti-bacterial, Anti-Fungal and

Anti-Static, Impermeable to Water and steam for uniform and optimum light distribution. Fixture should have IP20, CCT

11 MR 4000k, PF ≥ 0.95, THD<=10%, CRI 80 and drive should have Surge Protection upto 2KV and must be compatible with 6 SQ M 14375.00 86250.00

DALI 2.0 for both tunning and dimmable option. The LED Driver shall be easily available in India for repair and service.

DALI 2 Driver must be of Fulham SP / Tridonic Prog / Osram OTI Make only with Part 251, 252 and 253 for energy

mesaurement data. The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along

with Photo Biological Safety Standard. Luminaire should have RoHS, EMI EMC as per IEC 61547, CISPR 15. Make: Wipro

LM98 (DALI) /Regent/LT

Supply , Installation, Testing and Commissioning of 6m octagonal Pole with single arm. Material for pole section: Hot rolled

product of non alloy structural steel grade S355, Other parts: MS as per IS 2062. Material as per BS EN 10025 equivalant

to Indian standard.. Bottom (O.A.F.) 130mm and top (O.A.F.) 70mm. Size of Base Plate: 220 SQ, thickness of base plate

should be minimum 16mm, hole PCD 220, hole dia 24mm. Tolerance on material thickness as per IS:2629. Pole shall be

12 MR hot dip galvanized with coating thickness of 75 microns average as per IS: 2629. Make: Wipro, Philips, Valmount 7mtr. 25 Nos 17250.00 431250.00

octagonal pole with single arm of 1000mm length and 33.7mm dia including civil foundation.

Make: Wipro, Valmont, Transrail

Supply , Installation, Testing and Commissioning of surface/wall mounted SMD LED bulkhead luminaire of 10W LED

fixture with System efficacy of 100 lm/W and 1000 system lumens, operating in ambient temperature of 0⁰C to 45⁰C at

50Hz frequency . Luminaire shall be made up of pressure die cast aluminum housing powder coated in dark gray with

polycarbonate high transmissivity opal diffuser, ensuring uniform illumination and excellent heat dissipation. LEDs used in

the product complies with IEC 62471 for Photo-biological safety. Luminaire is with high quality silicon gasket of IP65 and

IK10 protection . EMC/PCT package of wattage of 1-3 W LEDs used in the product shall comply with IEC 62471 for Photo-

biological safety. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul

should be provided. The LED shall comply with L70 life of 50000 burning hours tested at maximum current .The LEDs used

13 MR shall be with CCT of 5700 K and CRI of minimum 80, with MacAdam CCT binning < 7 mounted on 1 mm MCPCB with 35 77 Nos 3450.00 265650.00

micron cu layer. LED Driver shall be of Integrated type prewired in product housing, Isolated, Constant Current with range

140-280V AC with internal surge protection of 2.5kV. Driver of Efficiency > 80%, Power factor of minimum 0.95 and total

harmonic distortion (THD) of less than or equal to 10% shall be integral to the luminaire. Manufacturer shall have inhouse

lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a

NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967;

# Public Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: FIRE DETECTION AND ALARM SYSTEM WITH PUBLIC ADDRESS AND 2-WAY COMMUNICATION

DSR (E&M) 2025 Amount

S No Description of Items Unit Rate

QTY DSR Amount NDSR Amount

Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm panel, central

processing unit with the following loop modules and capable of

supporting not less than 240 devices (including detectors) and

minimum 120 detectors per loop and loop length up to 2 km, network

communication card, minimum 320 character graphics/ LCD display with

keypad and minimum 4000 events history log in the non volatile memory

1 28.2 (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with

24 volt sealed maintenance free batteries with automatic charger. The

panel shall have facility to connect printer to printout log and facility to have

seamless integration with analog/digital voice evacuation system (which is

part of the schedule of work under SH: PA System) and shall be complete

with all accessories . The panel shall be compatible for IBMS system with

open protocol BACnet/ Modbus over IP complete as per specifications

Supplying, installation, testing & commissioning of repeater panel with 320

3 28.2.3 character/ Touch screen LCD display with inbuilt reset, acknowledge and 1.00 Each 113734.00 113734.00

silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog

4 28.2.4 addressable photothermal detector with in-built isolator complete with 125.00 Each 3,004.00 375500.00

mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on

5 28.2.5 surface/recessed MS Box having two LED, metallic cover complete with all 50.00 Each 306.00 15300.00

connections etc as required.

28.2.7 Supplying, installation, testing & commissioning of fault isolator complete with 3,434.00

6 base as required. 10.00 Each 34340.00

Supplying, installation, testing & commissioning of intelligent addressable

7 28.2.9 thermal detector with rate of rise cum fixed temperature thermistor having in- 5.00 Each 2,866.00 14330.00

built isolator complete with base as required.

28.2.10 Supplying, installation, testing & commissioning of addressable fire control 3,156.00

module complete as required.

28.2.11 Supplying, installation, testing & commissioning of addressable phone control 3,432.00

module complete as required.

28.2.14 Supplying, installation, testing & commissioning of addressable manual call 4,063.00

point complete as required.

39 Digitally signed by AKSHIT

28.2.15 Supplying, installation, testing & commissioning of addressable horn cum 3,682.00

strobe complete as required.

Supplying, installation, testing and commissioning of addressable beam

detector with short circuit isolator (inbuilt or separate) complete with emitter

13 28.2.12 and reciever including connections with remote test features etc complete as 2.00 Each 78525.00 157050.00

28.2.13 Supplying, installation, testing and commissioning of addressable duct 8,183.00

detector including suitable photo detector complete with base as required

28.3.1 Supplying, installation, testing & commissioning of 6 zone, voice alarm 132115.00

controller with USB, MP3 player (including 6 zone button paging station) with

seamless integration facility with main fire alarm panel for voice evacuation

complete as required.

28.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker 1025.00

complete as required.

28.3.3 Supplying, installation, testing & commissioning of 1.5/3/6W metal box 1,891.00

ceiling/wall speakers complete as required.

28.3.7 Supplying, installation, testing and commissioning of digital audio amplifier 75 152368

watt, 25V rms operating at 240 Volt AC Supply complete as required

28.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6 85,450.00

zone, with microphone assembly complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated

19 28.5.2 with annealed copper conductor having XLPE insulation, steel wire armouring 1400.00 Each 192.00 268800.00

& FRLS outer sheath complete as required.

1.2 Supplying and fixing of following sizes of steel conduit along with accessories

in surface/recess including painting in case of surface conduit, or cutting the

wall and making good the same in case of recessed conduit as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper

conductor cable in the existing surface / recessed steel conduit of following

21 pairs, cores and size including connections and interconnections etc. as

(a) 28.5.3.1 Speaker cable Single pair, 2-core, 1.5 sqmm 840.00 Mtr. 61.00 51240.00

Supplying & Fixing of battery operated illiminated "EXIT" signage, with

2hrs power Battery backup complete as required.

40 Digitally signed by AKSHIT

Fire Piping, Hydrants, Sprinklers and Accessories

S No DESCRIPTION QTY UNIT RATE AMOUNT

E&M AMOUNT (DSR)

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable

for automatic operation and consisting of following, complete in all respects, as required:

(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze

impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

(b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable

for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure,

horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

1 27.1. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as

(d) Suitable cement concrete foundation duly plastered with anti vibration pads.

Supplying, installation, testing and commissioning of diesel engine driven main fire pump

suitable for automatic operation and consisting of following, complete in all respects, as

required: (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron

body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS

standard complete with auto starting mechanism, 12 /24 volts electric starting equipment,

diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm

thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments

and protection as per standard specification, stop solenoid for auto stop in the event of fault

with audio indications, painted with post office red colour etc. as required. M.S fabricated,

common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable

cement concrete foundation duly plastered and with anti vibration pads.

Digitally signed by AKSHIT

(a) Supplying, installation, testing and commissioning of electric driven pressurisation pump

conforming to IS 12469: 2019 suitable for automatic operation and consisting of following,

complete in all respects, as required : (Jockey Pump) (b)Horizontal type, multistage, centrifugal

pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal as

required. (c)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415

volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot

mounted type with Class 'F' insulation, conforming to IS-12615: 2018. 194 DELHI SCHEDULE

3 27.3 OF RATES (E&M)-2025 (d)M.S. fabricated Common base plate, coupling, coupling guard,

foundation bolts etc. as required. (e) Suitable cement concrete foundation duly plastered and

with anti vibration pads.

(a) Supplying, installation, testing and commissioning of electric driven terrace pump

conforming to IS 12469: 2019 suitable for automatic operation and consisting of following,

complete in all

respects, as required: (Terrace Pump)

(b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze

impeller with stainless steel shaft, mechanical seal as required.

(c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3

phase, 50Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted

type with Class

'F' insulation, conforming to IS-12615: 2018.

(d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as

(e) Suitable cement concrete foundation duly plastered and with anti vibration pads.

Digitally signed by AKSHIT

Fabrication, supplying, Installation testing & commissioning of Electrical control panel of cubical

construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised

hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank

treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid

27.5 strip, having switchgears and accessories, mountings and internal wiring, earth terminals,

numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump &

set complete as per CPWD specification with following in coming and Outgoings, suitable for

operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required:

400A, 50kA 4 Pole MCCB, Ics=100% Icu Rating Digital Voltmeter 0-500V with selector switch

Ammeter (0-400 A) with selector swtich & CTs etc.

LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps

Set of Copper Bus Bar 500Amps

(Note: All outgoing feeders for pumps should have digital Ammeter with selector switches, and

LED type ON, OFF, trip indicating lamps)

Main Fire Pumps

5 125 Amp, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for

60 hp pump with overload protection, current sensing type single phase preventor complete

with all acceessories and internal wiring required for automatic operation,

selector switch for local/remote, auto/manual/OFF operation. - 2 sets

63 Amp, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter

with overload protection, current sensing type single phase preventor complete with all

27.5.4 acceessories and internal wiring required for automatic operation, selector switch for 1 Each 388843 388843.00

local/remote, auto/manual/OFF operation. - 2 sets

Diesel Engine Control

Control for diesel engine comprising-Automatic/Manual selctor switch & 3 attempts starting

device, timers and relays as required, push buttons, start/stop in manual mode

Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication

Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt

meter, and 0-20 A DC Ammeter

All standard relays and accessories for automatic operation of diesel engine

System Controller

Designing, Supply, Installation, Testing and commissioning of system controller to control

operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in

sequence as per specification consisting of relays, timers. Sensors, annunciation window for

fault indication, complete as per specification

Digitally signed by AKSHIT

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS

1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts

6 27.7 bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint of required shade complete as

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS

1239/Class -II of IS: 3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc.

7 27.6 in ground including welding, excavation & providing cement concrete blocks as supports,

anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of

following sizes complete as required.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with

8 27.11 bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming

to IS 13095 of following sizes as required :

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with

9 27.12 non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers,

gaskets and conforming to IS 780 of following sizes as required :

Digitally signed by AKSHIT

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with

10 27.13 orifice of required size to be fitted between flange & landing valve of external and internal 14 NOS 1436.00 20104.00

hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes

11 27.14 confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required:

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of

12 27.15 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

Supplying and fixing single headed internal hydrant valve with instantaneous

Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to

13 27.9 IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

13.1 27.9.1 Single headed Gunmetal 4 NOS 8208.00 32832.00

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia

instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked,

14 27.10 conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required

14.1 27.10.1 Single headed Gunmetal 10 NOS 8208.00 82080.00

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,

conforming to IS 884 complete with the following as required. (a) 20 mm nominal internal dia

water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 (b) 20 mm nominal

15 27.17 internal dia gun metal globe valve & nozzle. (c) Drum and brackets for fixing the equipmets on

wall. (d)Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female

16 27.16 couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Digitally signed by AKSHIT

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal

17 27.18 diameter size nozzle conforming to IS 903 suitable for instantaneous connection to

interconnect hose pipe coupling as required :

18 MR Providing and fixing standard firemans axe with heavy rubber handle. 14 NOS 1056.00 14784.00

Supplying and fixing of fire brigade connection of cast iron body with gun metal male

19 27.19 instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe

connection conforming to IS 904 as required :

Providing and fixing weather proof cabinet of size not less than 0.6 x 0.6 x 0.45 mtr made out

of M.S. sheet not less than 1.5 mm thick having central opening and 4 mm thick glazed glass

doors (Two nos.) suitably marked on the outside 'with the letters "FIRE HOSE" including

20 MR necessary locking arrangement and painting in red colour suitable to accomodate, external 10 NOS 11095.00 110950.00

yard hydrant valve, 2 nos 15 mtr long Hose pipe, branch pipe, nozzle and fire man's axe. It

shall be mounted on boundary wall complete as required.

Providing and fixing 4 mm thick glass door of size 2.1 m x 0.9 m with anodized aluminium

frame of size 0.10 x 0.05 M with centre opening for fire hose cabinet. Suitably marked on the

21 MR outside with the letters "FIRE HOSE" including locking arrangement. All aluminium work to be 4 NOS 15370.00 61480.00

in Red P.O. colour.

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all

accessories as per manufacturer's specifications.

22 MR a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 10 NOS 11600.00 116000.00

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). 10 NOS 5260.00 52600.00

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683). 10 NOS 4476.00 44760.00

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating

68 degree centigrade with required accessories :

23.1 27.21.1 Pendant sprinkler 298 Each 599.00 178502.00

23.2 27.21.2 Upright Sprinkler 10 Each 599.00 5990.00

23.3 27.21.3 Horizontal side wall sprinkler 10 Each 699.00 6990.00

Digitally signed by AKSHIT

Providing, fixing, testing & commissioning of installation control valve of cast iron body,

brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm

and hydraulically driven mechanical gong bell to sound continuous alarm when the wet

24 27.24 riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure

switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe

of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height

with air release valve on top and flanged connection to riser, drain arrangement with 25 mm

25 27.20 dia gun metal wheel valve with required accessories, pressure gauge and paintingwith 1 set 19402.00 19402.00

synthetic enamel paint of approved shade as required.

Providing and fixing of pressure switch in M.S. pipe line including connection etc as required

Providing and fixing of flow switch in following sizes in M.S. pipe line including connection etc

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of

stainless steel complete with 15 NPT on reducer thread withmaximum working pressure of 175

28 27.25 PSI test pressure ofc875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to

sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets,

center bracket, stockbar of following sizes complete as required.

SAFETY SIGNAGE:Providing and fixing of photo luminiscent/visual markers signage made out

of photo luminiscent, produced luminization with suitable colours combination (Glow in dark)

with high intensity luminious properties covered with U/V statilized coating having following

features complete as required.

29 MR (a)Thickness of aluminium/ACP sheet 2.00 mm ±10%

(b)Service temperature - 40 C to 120 C

(c)Suitable for indoor surface, glow visibility for more than 8 hrs in total darkness.

One sided signage written in English and also in regional Language,if required, for the below

dimension Fire Safety Signages.

Digitally signed by AKSHIT

Signage printed with the above stated specification for

(i) "NO SMOKING" with board size 4"x12" at suitable point

(ii) Floor indentification signage with board size 4"x12" at suitable point

(iii) Exit signage board size 4"x12" at suitable point

(iv) Colour signages for "EVACUATION MAP OF EACH FLOOR" with board size of 18"x24" at 9216 SQ INCH 22.50 207360.00

(v) Lift Alert with board size 8'x12' at suitable point

(v) Signages of " FIRE ORDER" with the board size of 24"x36" at main exit/entry (Ground

Digitally signed by AKSHIT

Schedule of Quantities: Integrated IT ACTIVE

S No 2025/ MR Item Description UoM QTY Rate DSR Amount

Supplying, installation, Testing and commissioning of following

capacity 24 port Layer 3 Network Switch having features and

specifications etc. as mentioned here under: At least 20 X RJ-45

Gigabit Ethernet Ports and additional 4 combo 10/100/1000 base-

t/SFP Ports with additional 4 SFP+ ports non-blocking architecture by

having Switching capacity of min. 128Gbps and packet forwarding

rate of 95Mpps or higher, 16K MAC table. Console Port, USB port,

Internal AC Power supply with operating temperature of 0 to +50 0C.

Stacking port with stacking support of minimum 8 units per stack.

48K Mac address, 9K or more Jumbo frame, ERPS with enabling ring

to converge in less than 50 ms from node or link failure, Static

routing, Static, 6to4, ISATAP and GRE, IPv6 Neighbor Discovery

(ND), BGP, ISIS, MPLS, VRRP v2, OSPFv2/v3, PBR, Route

Redistribution, RIPv1/v2/ng, IP Helper all L3 Protocols should support

from day 1 for both IPv6 and IPv4, 802.1x, Port security, Radius C

TACACS+ authentication C accounting, DAD, DAI, DoS attack

1 39.4 prevention, SSH, Guest VLAN, IP Access List, MAC Access List. Nos 1 1,93,791.00 1,93,791.00

Multicast: VLAN, PIM-SM, PIMDM, PIM- SDM, PIM-SMv6, DVMRP

v3 and MSDP, IGMP C MLD Snooping, Flow mirroring, IGMP C MLD

Snooping Ǫuerier, Per-VLAN IGMP C MLD Snooping. SNMP, Dual

configurations, Multiple images, RMON, LLDP/LLDP-MED, sFlow,

DHCP/BOOTP Client, IPv4/IPv6, Syslog server, Debug command,

802.3ah Ethernet Link OAM, 802.1ag Connectivity Fault, Y.1731

OAM, 802.1Ǫbb Priority- based Flow Control (PFC), Dying Gasp,

Cable Diagnostics , 6 kV surge protection on all Gigabit Ethernet

ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC,

RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of

Department of Telecommunication, Government of India etc.

complete as required.

Digitally signed by AKSHIT

Supplying, installation, Testing and commissioning of following

capacity 24 port Layer 2 indoor Network Switch having features and

specifications etc. as mentioned here under: At least 24 X RJ-45

Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP

Ports with non-blocking architecture by having Switching capacity of

min. 168Gbps and packet forwarding rate of 125Mpps or higher, 16K

MAC table. Console Port, USB port, Stacking support of min. 8 units

per stack. Internal dual AC Power supply, STP, RSTP, MSTP, BPDU

Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP

Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD Groups 1K

or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND,

VRRPv3, UDP Helper, ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ,

Multicast VLAN, Protocol VLAN, VLAN Trunking, DHCP Snopping,

Server, server Screening. RADIUS , TACACS+ Authentication, ǪoS:

2 802.1P, 8 queues per port, ǪoS : WRR, Strict+WRR, WRED, 802.1p.

ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based

ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP

server, relay, client, LLDP, LLDP-MED, OAM, Dying Gasp, 802.3ah,

sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV surge

protection on all Gigabit Ethernet ports and on all GE RJ-45 access

ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product

must be on Trusted Telecom Portal of Department of

Telecommunication, Government of India etc. complete as required.

24 port PoE Layer 2 Network Switch with PoE Support of 370W or

39.3.1 higher with each copper port supporting 802.3at PoE+ min. Nos 6 1,25,393.00 7,52,358.00

39.3.2 24 port Layer 2 Non-PoE Network Switch Nos 6 86,163.00 5,16,978.00

Supplying, Installation, Testing and commissioning of small form-

39.6 Pluggable (SFP) for Network Switches. Must be hot Pluggable, RoHS

3 Complaint, etc. complete as required.

39.6.3 10 G SFP + Single Mode/Multi Mode Nos 2 14,972.00 29,944.00

Digitally signed by AKSHIT

Supplying, Installation, Testing and commissioning of indoor Wireless

Access Point for High density use having features and specifications

etc. as mentioned here under- WiFi6 802.11ax 574Mbps (2.4GHz) +

2402Mbps (5GHz), WIFI 6 Certified, 1 x RJ45 console port, MG

2.5G LAN POE Port, factory reset, WPA/WPA2/WPA3™

Personal/Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC

address access control, Internal RADIUS server, SNMP,

Customizable Captive Portal, Auto Channel, Works as Access Point,

WDS, WDS with AP, Wireless Client, Web (HTTP), Secure Socket

Layer (SSL), Traffic control, Support ATF/Fast Roaming/Band

Steering, Supports enhanced security – WPA-PSK/WPA2

4 39.8 PSK/WPA3-PSK and RADIUS client, and Cipher negotiation, and Each 10 35,559.00 3,55,590.00

MAC/ IP ACL for networks

Certifications: MTCTE, CE, FCC. Works as Standalone, Compatible

with S/W & H/W Controller with addtional features like - Real-Time

Monitoring and Alerts, Rich Advanced Features, Centralized Device

Management, Role-Based Administration, Real-Time Monitoring,

VLAN and Access Control, Auto RF Management and Bandwidth

Optimization, Multi-SSID and Captive Portal Authentication,

OEM/Product must be on Trusted Telecom Portal of Department of

Telecommunication, Government of India etc. complete as required

Digitally signed by AKSHIT

Schedule of Quantities: IT PASSIVE

S No Item Description UoM QTY Rate DSR Amount NDSR Amount

Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc.

complete as required.

39.13.1 Copper Patch Cords of length 1m (3ft) Set 212 173.00 36,676.00

39.13.2 Copper Patch Cords of length 3m (10ft) Set 212 405.00 85,860.00

Supply, Installation, Testing and Commissioning of loaded Patch Panel 24 Port Cat 6A U/UTP ,The Cat-6Atransmission performance is in compliance and Exceeds ANSI/TIA/EIA-

568.2-D Standard. Supports 1000-Base-T. 90 Degree (Top Entry) or 180 Degree Punch Down Design for Convenient Network Terminations, Individual replaceable jack module

2 MR panel design as applicable.UL Listed, Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863 and ASTM B 117 Certified. OEM should have ISO 9001:2015, ISO Nos 12 12,500.00 1,50,000.00

14001:2015and ISO 45001:2018 or latest.All networking passive material (Fiber Cable, Copper Cables, Networking Racks and their connectivity components) should be from one

OEM make only for Data as per given Specification etc. all complete

3 MR Supply Installation Testing & Commissioning of 1 uPVC Cable Manager as per given specification etc. Nos 12 1,250.00 15,000.00

4 MR Supply, Installation, Testing & Commissioning of Mounting Hardware pack of 10pcs as per given specification etc. all complete Nos 5 200.00 1,000.00

Supplying and fixing 42U Rack with 6 inch Castor wheels and front brake Floor Standing Rack with Main Frame Pillar of 1.6mm CRCA Sheet with removable side panels, L-

Shape adjustable Vertical Mounting Rail of 2mm with 'U'Marking completely knocked-down condition (CKD) Shape, fitted with 4 number cooling fans, minimum 8nos two line cable

5 39.25 entry/exit provision at top and bottom with rubber protection, Front door 5mm Toughened Glass with MS frame or MS perforated with lock, Rear MS vented or perforated door, Nos 2 32,954.00 65,908.00

Powder coated Color- RAL- 7035 or black, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws

packet of 20 x 1 number, etc. complete as required.

Supplying, Installation, Testing and commissioning of CAT6A Copper Information Outlet (IO) with face plate of color as per site requirement, should have ETL/UL verification

6 39.15 program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and components should be from same OEM to maintain compatibility and interoperability etc. complete Nos 212 302.00 64,024.00

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non-Plenum, Horizontal (solid)

Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded

39.18 insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-

568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by

7 UL/ ETL etc. complete as required.

Supplying, Installation, Testing and commissioning of RJ45 Connector for CAT 6/6A Cables. RJ45 modular plug supports 4 twisted pairs, 8 positions, 8 connectors. Housing: PC,

UL94V-2, transparent color, Use for 24- 26 AWG stranded wires etc. complete as required.

Supplying and drawing following core Multi mode Fiber Optic Cable having corrugated steel armoring, leser optimize 50/125 μm with HDPE jacket, LSZH (Low smoke Zero

Halogen), Tight-buffered or loose tube, maximum attenuation: < 3.5 dB/km at 850 nm, < 1.5 dB/km at 1300 nm, bandwidth > 2000 MHz-km at 850 nm, > 500 MHz-km at 1300 nm

compliance and certifications: ISO/IEC 11801 Ed. 2.2, ANSI/TIA-568-C.3, ITU-T G.651.1 RoHS compliant. Multi Mode Fiber shall be Central-loose tube filled with Thixotropic jelly,

duly following Standards: ISO 11801, IEC 60793-1/60794-1-2, ITU-T-REC G.652D and Telecordia GR-20-core, High quality Electro Chromium Coated Corrugated Steel tape

39.20 (ECCS ) and HDPE- Sheath, Operating ambient Temperature should be – 5 0C to +50 0C and Storage Temperature should be – 5 0C to +50 0C, Maximum Attenuation ± 3.5

dB/km at Operational Wavelength 850 nm and ± 1.5 dB / km at Operational Wavelength 1300 nm . type of fiber should be 50/125 / G.652D & Refractive Index should be

1.483/1.478, The value for Mode-filed, Cladding Diameter 50 ± 2.5 μm and 125 ± 1μm correspondingly i/c splicing & marking etc complete as required.

39.20.1 6 Core Multi Mode Optical Fiber Cable meter 200 87.00 17,400.00

52 Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: EPABX (TELEPHONE & INTERCOM SYSTEM)

DSR AMOUNT (RS.)

S NO 2025/ DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

Supplying, installation, testing and Commissioning of

IP based voice communication system with 04 Port

Voicemail, 04 Port FXS, 04 Port FXO, 1 PRI Trunk

lines (30 Channels) Circuit with CLIP Facility, min 100

IP users License with provision for further additions,

100 analog users, 01 Number IP based Operator

1 38.1 Console, 100 Party Conference, Speed Dial, Music on Each 1 15,78,920.00 15,78,920.00

Hold, Internal/ External ring difference, Call Barring,

Call Pickup, Redundant server in active -Active mode

and as per technical specification including supporting

accessories etc complete as required. The system

should have valid TEC GR approval from DoT.

Supplying, Installation, Testing & Commissioning of

Type 1 IP Phone having 2 VoIP account, 120 x40 DOT

2 38.3 matrix screen with backlight, Full HD duplex speaker Each 54 11,698.00 6,31,692.00

phone, IPV6, Gigabit Etherent, PoE etc. complete as

Supplying and drawing 20 Pair 0.5 mm dia FRLS PVC insulated

annealed copper conductor, unarmored telephone cable in the existing

3 38.5 surface/ recessed steel/ PVC Conduit etc. complete as required. Metre 100 344.00 34,400.00

53 Digitally signed by AKSHIT

SCHEDULE OF QUANTITIES: IP Based CCTV System

S NO DESCRIPTION Unit QTY RATE

R DSR (INR) NON-DSR (INR)

Supplying Installation Testing and Commissioning of 5/6MP IP IR Dome Camera having following specifications and features etc :- 1)Type of Camera: Dome Camera 2) Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night condition 3) Signal System: PAL/NTSC 4) Minimum Illumination:

0.008Lux@ F1.4, AGC ON, 0 lux with IR or better 5) Imaging: 1/3s to 1/30000s Shutter Support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. 6) On Screen Display: Camera should display Camera title, Date & Time in live & recorded video

both. 7) Signal to Noise Ratio: > 50 dB 8) Day & Night: True Day & Night High Performance Mechanical IR cut filter with auto switch, IR Source Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR 30 Mtrs for colour view in night. 9) Video Compression (Minimum): H.265 or better, Audio:- G.711U/A,

G.711Mu, G.726, AAC, G.723 10) Wide Dynamic Range: WDR (120dB or more) 11) Digital Noise Reduction: DNR (2D/3D) On/Off 12) Streaming: Triple streaming, configurable 13) Video Streaming & Frame Rates: Triple streaming , configurable Main stream: 5/6MP @25/30 fps, Sub streams: D1@25/30 fps or better 14)

Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser 15) Profile Management: User configuration import, export 16) Security: User Authentication, Water Marking 17) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot

1 40.5 upto 512 GB. It should be supplied with minimum 128GB memory Card. 18) Recording Management: Format SD, overwrite, storage management, video to NAS device, 19) Edge Analytics : Tripwire, Intrusion, Motion Detection 20) Alarm Trigger : Motion/tampering detection;network disconnection detection; IP conflict

detection; memory card state detection; memory space detection 21) Alarm Support: It should have 1/1 Alarm In/ Out Port

22) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external Mic. and Speaker (As per site requirement) with G.711U/A/ G.711Mu/ AAC/ G.726 audio compression

23) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

24) System Capability: ONVIF

25) VMS: Camera shall support open source VMS

26) Cyber Security: trusted boot, AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, , account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade.

27) Ethernet: 1 RJ 45 10/100 Ethernet port

28) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter) and PoE—to ensure continuous operation in the event of a failure in one power source.

29) Power Requirement: 12VDC/24VDC/PoE (802.3af)/ePoE

30) Enclosure: IP67 weather proof, IK10

31) Operating Condition: Ambient Temperature:- (-) 05°C to 50°C, humidity 95% (max) (non-condensing)

32) IR life: 40000 hours or higher

33) Video Bit rate: 32 KBPS - 8 MBPS or better

34) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

1.1 40.5.2 5MP/6MP IP IR 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens Dome Camera. Nos. 18 26,993.00 4,85,874.00

Supplying Installation Testing and Commissioning of

5MP/6 MP IP IR Bullet Camera having following

specifications, type of lens and features etc :-

1) Type of Camera: Bullet Camera

2) Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night condition

3) Signal System: PAL/NTSC

4) Minimum Illumination: 0.006Lux@ F1.4, AGC ON, 0 lux with IR or better

5) Imaging: 1/3s to 1/30000s, Auto Gain Control ,White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking.

6) On Screen Display: Camera should display Camera title, Date & Time in live & recorded video both.

7) Signal to Noise Ratio: > 50 dB

8) Lens Type & Focus: as given below.

9) Day & Night: True Day & Night High Performance Mechanical IR cut filter with auto switch, IR Source Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR and 30 Mtrs for colour view in night.

10) Video Compression (Minimum): H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723

11) Wide Dynamic Range: WDR (120dB or more)

12) Digital Noise Reduction: DNR (2D/3D) On/Off

13) Streaming: Triple streaming, configurable

2 40.6 14) Video Streaming & Frame Rates: Triple streaming configurable Main stream: 5MP/6MP @25/30 fps, Sub streams: D1@25/30 fps or better

15) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser

16) Profile Management: User configuration import, export

17) Security: User Authentication, Digital Water Marking

18) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be supplied with minimum 128GB memory Card.

19) Recording Management: Format SD, overwrite, storage management, video to NAS device,20) Edge Analytics: Tripwire, Intrusion, Motion Detection

21) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space detection

22) Alarm Support: It should have 1/1 Alarm In/ Out Port

23) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external Mic. and Speaker (As per site requirement) with G.711U/A / G.711Mu/ AAC/ G.726 audio compreesion

24) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS,unicast,

25) System Capability: ONVIF

26) VMS: Camera shall support open source VMS

27) Cyber Security: trusted boot, AES 256-bit Encryption,Configuration encryption, trusted execution, Digest, security logs, account lockout, ,video encryption, IP/MAC filtering, HTTPS, trusted upgrade.

28) Ethernet: 1 RJ 45 10/100 Ethernet port

Power Input: The camera should support

simultaneous dual power input—12 VDC (via power

adapter) and PoE—to ensure continuous operation in

2.1 40.6.2 5MP/6MP IP IR 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens outdoor Bullet Camera. Nos. 6 26,993.00 1,61,958.00

54 Digitally signed by AKSHIT

Supplying Installation Testing and Commissioning of

PTZ (Pan,Tilt and Zoom) IP IR Camera having

following spcifications and features etc :- PTZ (Pan,Tilt and Zoom) IP IR Camera having

following spcifications and features etc :-

1) IP IR PTZ Camera: Motorized PAN TILT ZOOM

2) Image Sensor: 1/2.8" or better progressive Scan

3)Signal System: PAL/NTSC

4) Minimum Illumination: 0.008 Lux@ F1.6, AGC ON,,

0 lux with IR, or better

5) Imaging: 1/1s to 1/30000s, Auto Gain Control ,

White Balance- Auto, Back Light Compensation,

Image Rotation, Multi zone Privacy Masking (Upto 24

3 40.9 Area), HLC, Defog, Region Of Interest and EIS

6) On Screen Display: Camera should display Camera

title, Date & Time in live & recorded video both.

7) Signal to Noise Ratio: > 50 dB

8) Event Notification: Through Relays, E-Mails or FTP

9) Day & Night: True Day & Night High Performance

Mechanical IR cut filter with auto switch, IR Source

Inbuilt IR LED's with effective distance. The camera

should have IR LED’s and cover distance up to 300

10) Auto Tracking: The camera should be equipped

with Deep-learning-based auto tracking function using

simultaneously all of the panning, tilting and zooming

should be available. When a motion is detected in a

5MP IP IR motorized PTZ @25/30fps or better

camera, Triple streaming , configurable on resolution:-

3.1 40.9.3 streams:1080p@25/30 fps, varifocal lens 3.95mm Nos. 4 1,07,974.00 4,31,896.00

(±5mm) ~ 177.75mm (±5mm) or better with Automatic

& manual Focus Adjustment provisions, 45x Optical

zoom and 16x Digital zoom with angle of view H:

Pan: 0° ~ 360° endless,Manual Pan: 260° /s, Preset :

300° /s, Tilt Travel: Tilt: -20° ~ 90°, auto flip 180°,

Manual Tilt: 120° /s, Preset : 200° /s

Supplying Installation Testing and Commissioning of following Channel Network Video Recorder (NVR) with camera licenses to record for all channels having specifications and features etc as mentioned below:

1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses to record per NVR and to provide a live view, storage and simultaneously Multi-channel playback of all IP camera or more and must be ONVIF with minimum support of 384 Mbps incoming Bandwidth.

2) NVR should support video compressions : H.265 or better, H.264, MJPEG.

3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with G.711U/A, G.711u, PCM, G726 audio compressions.

4) Intelligent auto power on when power resumes after power outage.

5) Storage: It should support minimum 8 SATA Slots with 20TB capacity/ Slot and RAID support of RAID 0/1/5/6/10.

6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232, 1x eSATA Port

7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0)

8) Video Output Ports: 2x HDMI and 2 VGA

9) Alarm Ports: It should have 16/8 Ch In/ Out ports to connect various type of external sensors and output devices like hooter/ Siren etc.

10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated mobile number for power failure, HDD failure, vandalism, tempring, network disconnection and panic

11) Web & Mobile Application: Web, Mobile app (For iPhone, iPad, Android Phone) for alerts and viewing.

12) Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP Filter, PPPoE, FTP, DDNS, Alarm Server, IP Search, Multicast, Auto Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and OEM Cloud for remote monitoring without any public IP need.

13) Standards: CE, FCC, RoHS, BIS Certified

14) Power Supply : Should support AC100-240V, 50/60Hz Power supply.

15) Operating Condition: -5°C to 50°C, humidity 90% (max) (non-condensing)

4 40.11 16) The VMS application shall support all the features & functionalities of the offered cameras.

17) VMS should consist Licenses for all channels to record Cameras with General, motion detection, intelligent, alarm and POS recording modes. VMS should be provided with Camera Licenses, with no dependency of VMS licenses by binding with the MAC address of the cameras to achieve the functionality.

18) The NVR OEM shall be responsible for providing a mobile application compatible with both Android and iOS devices, enabling remote monitoring and playback of cameras/NVR footage.

19) The OEM must provide its own DDNS server hosted in India, eliminating the need for a public IP address for remote monitoring over the Internet.

20) Must support Continuous, Alarm, Motion, Instant, Panic Recording Mode

21) It should support Resolution: 32MP; 24MP; 16MP; 12MP; 8MP; 5MP; 4MP; 1080p; 720p; D1; CIF; QCIF

22) When alarm recording is enabled and an event occurs, you can click the alarm icon on monitoring page to view the alert details. The snapshot function is supported on monitoring and playback page

23) The Network Video Recorder (NVR) shall be configured to send email whenever a system message is created or an alarm event occurs. The email server shall be a valid SMTP server. Each recipient email address shall be configured to receive any combination of critical, warning, or informational messages or alarm

notifications. When an alarm occurs, the email message includes the NVR name, time of alarm and a list of camera that is configured to record upon alarm

24) It should have Web and GUI interface.

25) Built-In Artificial Intelligence: NVR should have built-in AI: - 2 Channel face detection and recognition, - Minimum 4 Channel perimeter protection, - Minimum 8 Channel

Smart Motion Detection

26) Face Recognition Database Capacity: It should support total Blacklist and Whitelist capacity of Minimum 20,000 Faces or more with Face Detection speed of 12 face images/sec and facility to add Name, gender, birthday, address, credential type, credential No., countries & regions and state to each face image.

27) Face & Human Attributes Search: Search Pictures/ Video by Gender, age group, glasses, expressions, face mask, beard, Top color, top type, hat, bag, age, gender and umbrella.

28) ANPR Capability: It should support ANPR Camera with License plate, plate color, vehicle body, vehicle model, vehicle logo, calling, seatbelt, vehicle registration location etc vehicle attributes.

29) Alarm Notifications based on: Motion detection, video tampering, video loss, scene changing, PIR alarm, Camera external alarm, Face detection, face recognition, perimeter protection (intrusion and tripwire), ANPR, people counting, stereo analysis, crowd distribution, heat map, Disk Full, Storage Error, IP Conflict and

abnormal behavior of fan, cybersecurity exception

30) Alarm Notification should be linked with Recording, snapshots, Camera external alarm output, buzzer, logs, presets and email.

4.1 40.11.1 32 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16/25/32(36), 2nd screen: 1/4/8/9/16 Nos. 1 64,784.00 64,784.00

Supplying, Installation, Testing and Commissioning following capacity Serveillance grade Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL Certifications.

Supplying, Installation, Testing and Commissioning of following size LED display (LED monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits or better, Video wall mode should be available, contrast ratio:

1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on monitor screen and programmable with remote (remote shall be supplied with system), Key Board, Optical Mouse, etc. as required.

55 Digitally signed by AKSHIT

Schedule of Qunatities: Integrated Access Control System

S No Item Description Qty Unit Rate DSR Amount NDSR Amount

Access Control System with Face recognition Supplying, Installation,

Testing and Commissioning of Access Control System comprising of

Face and fingerprint Recognition, Smart Card, QR Code, NFC & PIN

Code based Reader, following sizes of 5” IPS TFT Touch Screens, 1GB

RAM, 8 GB ROM, Live Face Detection with anti-spoofing against 2D

photograph, mobile selfie & video, Fake Fingerprint and face

Detection Technology, 30,000 Face storage (1:N) /, 3,000 fingerprint

(1:N), QR code 30,000, 30,000 card storage (1:N), 2 lakh transaction

storage, 20,000 image logs, onboard dual camera (colour & IR)

Primary camera min 2MP, Support authentication & verification

from up to 1 meters, Communication protocols WiFi, TCP/IP,

Wiegand Out, Wiegand IN, USB, MQTT protocol, Blacklist Employee

Management, User wise authentication modes; Built in Lock Control,

Mask Detection & Alert (configurable), 40 to 30,000 lux illumination,

IP65 for Ingress Protection, Certification: CE, FCC, BIS, ROHS, etc.

Metal Enclosure with battery backup, suitable for mounting on metal

surface/metal frames/ wooden frames/wall/flap barriers including

all mounting bracket & accessories complete etc. as required.

1.1 41.1.1 5" IPS TFT Touch Screen 8 Each 58,306.00 4,66,448.00

Software for Web based Access Control System Supplying,

Installation, Testing and Commissioning of Web based Access

Control Enrolment and Device Configuration Software, Should be

independent of OS (Windows), Unified Management of Biometric,

Card, and Controllers, Import Functionality for bulk user details,

Biometric Template Retrieval for Data Recovery, User Management,

Logs and Terminal Management, Support for IP-based and USB

2 41.5 Biometric Devices, User-specific Access Policies, Different User 1 Nos 97,176.00 97,176.00

Policies on the Same Terminal, Assignment of Specific Access

Schedules, Pushing Users to Terminals or Groups, Admin Authority

Management to define rights of each user to perform, Blacklist User

Management, Access Schedule Creation, Real-Time Log Retrieval,

Real- Time User Identification, Secure Storage of Biometric/Users

Data, Capable to integrate with 3rd party applications over Web

API's, MQTT protocol support

Electromagnetic locks Supplying, Installation, Testing and

Commissioning of Electromagnetic locks (fail safe type) for following

type of Doors suitable for operation on 12 V DC having holding force

600 lbs for Single Leaf Door and 1200lbs for Double leaf door with

suitable feedback i/c connection complete etc. as required.

3.1 41.6.1 Single leaf door 1 Nos 4,831.00 4,831.00

3.2 41.6.2 Double leaf door (Each leaf 600lbs & Total 1200 lbs) 8 Nos 7,593.00 60,744.00

Exit Push Button

Supplying, Installation, Testing and Commissioning of

4 41.7 Heavy Duty SS Finish Exit Push Button for releasing 8 Nos 1,173.00 9,384.00

access doors with all necessary installation

accessories i/c connection complete etc. as required.

Door Position Sensor Supplying, Installation, Testing and

5 41.8 Commissioning of Door Position Sensor i/e connection 8 Nos 622.00 4,976.00

complete etc. as required.

Supply, Installation, Testing & Commissioning of Smart card

Frequency Excitation (13.56 MHz) Mifare smart Card , distance upto

2.5" Memory Type EEPROM, 2K bit memory Complies with ISO/IEC

6 standards for thickness. Lifetime Warranty .etc. as per specifications 200 No. 452.00 90,400.00

of this tender etc complete as required and directions of Engineer-in-

Supply, Installation, Testing & Commissioning of 3 core 1.5 Shielded

communication multi-stand Data Cable etc. as per specifications of

7 this tender etc complete as required and directions of Engineer-in- 240 Mtr 147.00 35,280.00

Schedule of Quantities: Integrated Audio Visual System

S No Item Description UoM Qty Rate NDSR Amount

SITC of All In One 138" Diagonal Screen, Pixel Pitch

(mm) P1.5, Aspect Ratio 16:9, Resolution 1920×1080,

Operating System Android 9.0, CPU Dual Cortex-A72

large core + four Cortex-A53 small core, frequency

1 2.0GHz, RAM 4GB, Storage 32GB, built-in 2*30W Nos 1 38,75,000.00 38,75,000.00

audio, support 2.0 channels, Supports Bluetooth

function with required wall mount etc all required

SITC of 86" 4k, UHD Professional Signedge Display

with 500 NITS, 24*7 ,Built in SOC/ Media Playerwith

Quad Core Processor, Built in Open Platform Android

11, 3X HDMI, Audio Input Audio Output, Built in

Speaker(12W x 2) ;Including mounting bracket, Built-

in Chromecast, Dolby Digtial audio HDMI-CEC device

2 linking supported, 3 USB(2.0), 3*HDMI(2.0 Side), Nos 1 3,50,000.00 3,50,000.00

Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4

GHZ Wifi,CPU Built in Mali G31 MP2 GPU-A55*4, 1.1

GHz Processer, 4 GB RAM 32GB Storage,Metal

Frame 12 W built speakers, With 3 years on Site

SITC of Fixed Wall Mount, capable of holding up to 75

3 kg and supports 37" to 100" displays, VESA Nos 1 10,780.00 10,780.00

Compliant etc all complete

SITC of Cable Cubby with flip top, cover and 6 Pass

Through Holes for multi-format cables, 2 Universal

4 Power Socket , 1 HDMI, 1 USB-C for Data Transfer, Nos 1 25,950.00 25,950.00

made of aluminium etc all complete etc all complete

SITC of All in One Conference Unit, Camera Sensor

1/2.5″, CMOS, Effective Pixel: 8.0M, 4 x MEMS mic

array, AEC | ANS | AGC 180° Pickup Angle pickup

Range: 5-8m (16-26ft) A.I. camera with smart

5 backlighting, auto-framing, speaker & presenter Nos 7 3,15,640.00 22,09,480.00

tracking, Inputs / Outputs 1x USB-C Input with Alt-

Mode, 1x HDMI Input, 1x HDMI Output etc all

SITC of 2 Meter Premium High Speed HDMI 2.0b

Flexy Cable, Bandwidth up to 18Gbps, Up to

6 4096x2160@60Hz at RGB 4:4:4 video resolution, Nos 4 3,250.00 13,000.00

High Dynamic Range (HDR10), Dolby Vision and

Hybrid log–gamma (HLG) video etc all complete

SITC of 10 Meter Active Copper HDMI Cable, Data

Rate: Up to 18.2Gbps, Colour Depth: Up to 16 bits,

Colour Formats: RGB 4:4:4 / Y’CBCR 4:2:2 / Y’CBCR

7 4:2:0, Consumer Electronic Control (CEC), Auto Lip- Nos 1 20,995.00 20,995.00

Sync Correction, Audio Return Channel (ARC),

Enhanced Audio Return Channel (eARC), High

Dynamic Range (HDR) etc all complete

SITC of 2 Meter USB Full-Featured Type-C cable for

USB 3.1 Gen2, 4 Lane Displayport Alt mode

(4K60FPS Video and Audio), Supporting peripherals

8 via USB 2.0 up to 480 Mbps (Mouse, Keyboard, Nos 1 3,950.00 3,950.00

Thumb Drive, Speakerphone and Webcam) etc all

SITC of 10 Meter USB 3.1 Gen1 SuperSpeed Active

Extension Cable TypeA/male to TypeA/female,

Supports 4K Webcam, SSD storage, Native

9 USB2/USB1 and USB3 extension, Plug and play Nos 1 37,500.00 37,500.00

compatible with PC, Mac, and Linux etc all complete

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NDSR

S NO DESCRIPTION UNIT QTY RATE

MR AMOUNT AMOUNT

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN MIXER

(WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY) LPM should be 2.5 with

MR 1 suitable aerators as per GRIHA norms. Manufacturer should have valid GRIHA certification EACH 14 3583.00 50162.00

MR 2 Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE: 630x460x130mm EACH 14 4591.00 64274.00

Supply, Installation, Testing and Commisioning of suitable compatible WASTE COUPLING 32MM-

FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioning of BOTTLE TRAP (WITH INTERNAL PARTITION)

MR 4 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES & WALL FLANGE EACH 14 2231.00 31234.00

Supply, Installation, Testing and Commisoning of RIMLESS, BLIND INSTALLATION WALL HUNG

MR 5 WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES SET, SIZE: EACH 13 12794.00 166322.00

MR 6 Supply, Installation, Testing and Commissioning of PNEUMATIC CONTROL PLATE EACH 13 1423.00 18499.00

Supply, Installation, Testing and Commisoning of ANGULAR STOP COCK WITH WALL FLANGE

Supply, Installation, Testing and Commissioning of CONCEALED STOP COCK WITH

ADJUSTABLE WITH WALL FLANGE 15mm

MR 9 Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH 8mm EACH 13 1725.00 22425.00

MR 10 DIA 1.2 METER

Installation, FLEXIBLE

Testing TUBE AND of

and Commisiong WALL HOOK ALD-CHR-573

PNEUMATIC SINGLE PIECE or equivalent. LPM

SLIM CONCEALED EACH 13 6318.00 82134.00

Providing WITH

and fixing INSTALLATION

P.V.C. waste pipeKIT

basin CONNECTION

including SET FOR

P.V.C. waste fittings

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6mm thick hard

board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality

13 conforming to IS : 8931

18.53.1 15 mm nominal bore EACH 42 574.30 24120.60

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun)

iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse sand: 6

17.61 graded stone aggregate 12.5 mm nominal size) including necessary plaster and pointing in cement

mortar 1:4 (1 cement : 4 coarse sand) :

18.76 Cutting holes upto 30x30cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks EACH 13 416.80 5418.40

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching

surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with

18.7 clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes METRE 100 335.00 33500.00

58 Digitally signed by AKSHIT

18.7.3 25mm nominal outer dia pipes METRE 80 401.55 32124.00

18.7.4 32mm nominal outer dia pipes METRE 80 518.75 41500.00

18.7.5 40mm nominal outer dia pipes METRE 20 702.95 14059.00

18.7.6 50mm nominal outer dia pipes METRE 50 934.15 46707.50

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps

at 1.00 m spacing.

18.8 This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting

chases and making good the same including testing of joints complete as per direction of Engineer

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes METRE 146 497.80 72678.80

18.8.2 20mm nominal outer dia pipes METRE 120 537.60 64512.00

18.8.3 25mm nominal outer dia pipes METRE 60 627.25 37635.00

18.8.4 32mm nominal outer dia pipes METRE 20 739.30 14786.00

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil,

waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary

specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors),

reducers, WC connectors, couplers, expansion joints / bellows, cowels, clamps, rubber rings, clean

outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside

duct / under floor & basement ceiling / external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from floor under false ceiling or

embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1

19 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of

MR shuttering for proper completion of the work, breaking and making good the walls and floors etc.

after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on 50x50x5

mm slotted angle. The cost will include all support arrangements. The work includes commissioning

of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 110 536.00 58960.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 60 416.00 24960.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/

Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces, enlarger, socket,

couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp & hangers etc.

MR 20 cutting holes in wall/ floors/ slabs and making good the same with cement concrete 1:2:4 complete

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating complete in

MR 21 all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 24 536.00 12864.00

MR 22 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. EACH 24 253.00 6072.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover with

screws and other required fitting complete as required.

MR 24 Supply, Installation, Testing and Commissioning of 15 litre geyser EACH 7 12004.00 84028.00

MR 25 Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER EACH 4 705.00 2820.00

MR 26 Supply, Installation, Testing and Commisiong of TUMBLER HOLDER EACH 4 705.00 2820.00

59 Digitally signed by AKSHIT

Supply, Installation, Testing and Commisiong of TOWEL RACK 600MM LONG WITH LOWER

MR 28 Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 4 568.00 2272.00

MR 29 Supply, Installation, Testing and Commisiong of TOWEL HOLDER EACH 4 1137.00 4548.00

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx.

17.80 30 size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), Each 5 7979.20 39896.00

having water inlet from back side, including fixing to wall with suitable brackets all as per

MR 31 manufacturers

Supply specification

Installation, Testing and

and direction of Engineer-in-charge.

Commisioing of Handicap Toilet special fixtures to the complete

(a) SITC of Grab Bar vertical swing white Each 1 9,867.00 9867.00

(b) SITC of Grab Bar Left/Right 90 angle Each 1 7271.00 7271.00

(c ) SITC of Grab Bar 842mm long white Each 1 4,664.00 4664.00

18.49 14 Providing and fixing C.P. brass bib cock of approved quality to conforming to IS 8931.

18.49.1 a) 15 mm nominal bore Each 13 506.80 6588.40

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards

18.51 15 and weighing not less than 690 gms.

18.51.1 a) 15 mm nominal bore Each 2 798.95 1597.90

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make

18.52 16 conforming to IS : 8931.

18.52.1 a) 15 mm nominal bore Each 18 670.45 12068.10

18.9.6 17 50mm nominal outer dia pipes M 200 794.25 158850.00

18.17 18 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end).

18.17.1A a 20 mm nominal bore Each 5 539.95 2699.75

18.17.1 b 25 mm nominal bore Each 2 622.40 1244.80

18.17.2 c 32 mm nominal bore Each 1 689.60 689.60

18.17.3 d 40 mm nominal bore Each 1 826.10 826.10

18.17.4 e 50 mm nominal bore Each 1 1026.65 1026.65

18.18 19 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats

18.18.3 a complete :

25 mm nominal bore Each 2 464.05 928.10

18.21 Providing and fixing unplasticised PVC connection pipe with brass unions.

18.21.1 30 cm length

18.21.1.1 a 15 mm nominal bore Each 150 85.00 12750.00

Providing and placing on terrace (at all floor levels) polyethylene water storage tank IS: 12701

18.48 21 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet Litre 30000 11.00 330000.00

and overflow pipes but without fittings and the base support for tank

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and

dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil,

2.10 and then returning the soil as required, in layers not exceeding 20 cm in depth including

22 consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated

soil as directed, within a lead of 50 m :

2.10.1 All kinds of soil

2.10.1.2 a Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. M 200 352.15 70430.00

19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick

23 masonry chamber

19.4.1 100x100 mm size Pwith water tight C.I. cover with frame of 300 X 300 mm size (inside) the weight of

19.4.1.2 a With Sewer bricks conforming to IS : 4885 Each 4 2685.20 10740.80

60 Digitally signed by AKSHIT

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C.

top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),

foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm

19.7 nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)

finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement

24 : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of

neat cement complete as per standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm

internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23

kg and weight of frame 15 kg):

19.7.1.2 a With Sewer bricks conforming to IS : 4885 Each 10 12711.80 127118.00

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 560 mm

19.7.3 25 internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg

and weight of frame 100 kg)

19.7.3.2 a With Sewer bricks conforming to IS : 4885 Each 1 32719.50 32719.50

19.8 Extra for depth of manholes

19.8.1 Size 90x80cm

19.8.1.2 a With Sewer bricks conforming to IS : 4885 Meter 10 8654.25 86542.50

19.8.2 Size 120x90cm

19.8.2.2 With Sewer bricks conforming to IS : 4885 Meter 1 10381.45 10381.45

Constructing brick masonry road gully chamber 50 X 45 X 60 cm with bricks in cement mortar 1:4 (1

19.27 27 cement : 4 coarse sand) including 500 X 450 mm precast R.C.C. horizontal grating with frame

complete as per standard design :

19.27.1 a With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 20 5957.90 119158.00

Supply, Installation, testing and commisioning of Domestic Water Pumps(to lift water from

underground domestic water tank to terrace tank of building)Location - Near underground water

tank with Level Controller with sufficient nos. of low / high level alarms, contacts with electrodes and

control wiring for the automatic operation of all water supply pumps to achieve the functional

requirement shall be provided. Control wiring between these pumps and water tanks shall be

provided. Raw water pumps must start at low level of water in underground domestic water tank &

MR 28 stop at high water level in that tank. Dry running protection shall be provided for all the pumps. All

water supply to operate automaticaly through level controller.

Capacity 1 LPS each minimum

RPM 2800 / 2 HP

Providing and Fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592

12.41 29 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised PVC moulded fittings/ accessories for unplasticized

12.42 Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring

30 conforming to IS: 5382, leaving 10mm gap for thermal expansion.

12.42.1 Coupler

61 Digitally signed by AKSHIT

12.42.6 Shoe (Plain)

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticized PVC rain

water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required

12.43 31 length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and

making good the wall etc. complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and

12.44 32 weighing not less than 440 grams Each 12 54.70 656.40

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar

in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone

19.2 34 aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design

19.2.2 a 150 mm diameter S.W. pipe meter 400 1179.85 471940.00

19.2.3 b 200 mm diameter S.W. pipe meter 400 1375.45 550180.00

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone

19.3 35 aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per

standard design

19.3.2 a 150 mm diameter S.W. pipe meter 400 743.10 297240.00

19.3.3 b 200 mm diameter S.W. pipe meter 400 873.50 349400.00

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff

19.6 36 mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints

etc. complete :

Supply, Installation, Testing and Commisioning of Sensor based basin mixer wall mounted. LPM

MR 37 should be 2.5 with suitable aerators as per GRIHA norms. Manufacturer should have valid GRIHA EACH 14 14377.00 201278.00

certification ( Ref Euronics Model No. ET77BE )

Supply, Installation, testing and Commisioning of Touch free infrered hand dryer (Ref Euronics

Model No. SJD2S)

Supply, Installation, testing and Commisioning of Automatic soap dispenser (Ref Euronics Model

Supply, Installation, Testing and Commisioning of Toilet Paper Holder with flap (Ref Euronics Model

Supply, Installation, Testing and Commisioning of Wall Mounted Paper Towel Dispenser (Ref

Euronics Model No. Linea P2 )

62 Digitally signed by AKSHIT

Supply, Installation, Testing and Commissioning of Electromagnetic Flow Meter/ Water Meter

having the following specs suitable for pipes upto 50 mm dia pipes:

Transmitter: Die Cast

Power Supply: 90 – 265 VAC

Outputs: 4-20 mA , Pulse, RS485

Process Pressure: 10 Bar

MR 42 Sensor Terminal Housing: C.S each 4 25300.00 101200.00

Fabricated IP65

Display: Remote Display With 5

Flange: ASA #150 C.S

Electrode: SS316L

Grounding Electrode: SS316L

Flow Tube: SS304

Coil Housing: C.S

Protection Class: IP-66

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets

43 and stainless steelDrain

40 mm, including painting of fittings and brackets, cutting and making good

17.10.1 Kitchen Sink with