SPL REP TO BLDG NO. P-70 (LPG SHED) OF 39 COY ASC (SUP) TYPE A AND CERTAIN LBW AND MINOR WORKS AT SHILLONG CANTT AREA UNDER GE UNDER GE SHILLONG

Amount

Dismantling of plain or corrugated steel sheeting any guage thickness including Nainital or similar pattern roof covering complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section in any position (unframed work) complete all as specified and directed.

All as per item No 2.00 here in above but in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and directed.

Dismantling of boarding any description fixed in any position complete all as specified and directed.

Dismantling of wall/ceiling boards of any description (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of Cement Concrete of any description ( reinforced) and in any position not otherwise specifically provided for etc complete all as specified and directed by Engineer-in-Charge.

Demolition of Cement Concrete of any description in any position not otherwise specifically provided for etc complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up drain pipes 150mm dia (slat glazed ware AC or reinforced concrete/PVC pipe) set in Cement mortar complete all as specified and directed.

Demolition of brick or solid concrete block walling built in cement mortar etc complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground in natural ground etc complete all as specified and directed by Engineer-in-Charge.

Dismantling of wrought Iron or mild steel work of any description not otherwise described complete all as specified and directed

Taking down Chowkhats or frames n.exc 1.5 Sqm each but with shutters (without taking off shutters from the frame) including builders hardware each complete all as specified and directed.

Taking down Chowkhats or frames exc 1.5 Sqm but n.exc 4 Sqm each but with shutters (without taking off shutters from the frame) including builders hardware each complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm and n. exc. 2 Sqm resecuring or easing & adjusting refixing in same opening complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm and n. exc. 2 Sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description n. exc. 1 Sqm each and removing from site complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces in anyposition including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MD land all specified and directed by Engineer-in-Charge.

Dismantling fencing wire mesh including fixing arrangement like flat iron, angles of any type etc complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft / loose soil n.exc 1.5m wide and n.exc 1.5m in depth; for foundation etc. n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out etc complete all as specified and directed by Engineer in Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, and removing surplus soil to a distance n.exc. 50 m from the starting point etc complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in hard/dense soil etc complete all as specified and as directed by Engineer in Charge.

Removing excavated materials (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M&L for RCC 1;1.5:3 type-A1(nominal mix) ( using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and as directed by Engineer in Charge.

M&L for RCC 1;1.5:3 type-A1(nominal mix) ( using 20mm graded crushed stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M&L for Pre-cast RCC 1:2:4 type B1, ( using 20 mm graded stone aggregates) as in cover slab, shelves and similar articles with plain faces and set in cement sand mortar 1:6 including necessary formwork and mould including demolition of old unserviceable one etc complete all as specified and as directed by Engr-in-charge.

Formwork to sides of concrete of rough finished on flat surfaces in foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed by Engineer in Charge.

Formwork to sides and soffits in rough finished flat surfaces of floor or roof beams,beam haunchings, girders,bressumers,lintels, cantilevers,shelves including support,overhangs etc also splays between floors and beams complete all as specified and as directed by Engineer in Charge.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed by Engineer in Charge.

M&L for Mild steel TMT deformed bars, 5 mm dia and over and upto 10 mm dia in stirrups, spacers and binders, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed by Engineer in Charge.

S&F mild steel works such as Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 etc complete all as specified and as directed.

S&F mild steel works such as Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge.

S&F mild steel channel or angle or tee sections, ms tube fixed to ms flat iron cut into shape ,drilling and fixing with screws etc conforming to Fe-410 (Gde-E-250) etc complete all as specified and as directed.

S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Supply only Chain link MS galvanised fencing, any size or type etc complete all as specified and directed by Engineer-in-Charge. .Note:- Size of fencing should be 100x100 mm

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of new GI binding wire etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor , foundation filling and mass concrete etc complete all as specified and directed by Engineer in Charge.

M&L for PCC (1:3:6) type C2 using 40mm graded stone aggregate as in sub base of floor , foundation filling and mass concrete etc complete all as specified and directed by Engineer in Charge.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engineer in Charge.

M&L 75mm thick PCC, type C2, (1:3:6, using 40 mm graded stone aggregates) as in floor, hardstanding and plinth protection and finishing the cement concrete surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for PCC( 1:3:6) type C2 (using 40 mm graded stone aggregate) as in surface channel and drains including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for extra for forming fair finished drain or channel 45cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc all as specified and directed.

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete (1:3:6) type C1, using 20 mm graded stone aggregate, exc 10 Cm width and setting in cement sand mortar 1:6 complete all as specified and directed.

M&L for 2nd class hard wood as in scantling, clean sawn, timber fixed complete all as specified and directed.

M&L 2nd class hard wood plain fillets square rectangular or triangular in section clean sawn secured with nails or brads sectional area exc 13 sqcm n exc 25 sqcm complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Rendering 15 mm thick in cement sand mortar (1:6) on fair faces of concrete surfaces finished even and smooth without using extra cement etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering, 15 mm thick plaster in cement sand mortar ( 1:4), in two layers, top 5 mm thick with approved Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a layer of 10 mm thick base layer etc complete all as specified and as directed by Engineer-in-Charge. Note WPC shall be measured and paid separately.

Supply only integral water proofing compound , ISI marked.complete all as specified and as directed.

M&L for Rendering 10 mm thick in cement sand mortar (1:6) on fair faces of concrete surfaces finished even and smooth without using extra cement etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Non Skid coloured Ceramic tiles, joint free, 7 to 8 mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour including screed bed or bedding layer of mortar 15mm thick in cement sand mortar (1:6) for laying floor tiles complete all as specified and directed.

M&L Glazed ceramic colour tiles of size 300x450x7mm /300x600x7 thick in vertical surfaces etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 complete all as specified and directed.

M&L of mastic flooring as per IS 1195/96 on concrete surface of RCC including hacking and cleaning the surface and applying one coat of primer bitumen paint on surface before laying mastic floor in Grade IV with thickness 25mm. The quality of bitumen is as per IS702, Lime stone powder, and fine aggregate shall be confirm to IS 1195 or 1196, The proportion of mixing of bitumen, lime stone powder and fine aggregate shall confirm to IS 1195/1196 including providing all necessary equipments complete all as specified and directed.

S&F 2nd class hard wood boarding, 20mm thick, as in eaves board/fascia plained one side with butt joints fixed with nails etc complete all as specified and as directed.

M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination as in kitchen cabinet / cup-board including taking down old unserviceable one etc complete all as specified and directed.

S&F Anodised Aluminium frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Aluminium main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mm c/c using Gi wire of 4mm thickness Aluminium frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and as directed .

M&L for 4mm thick E Board 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer instruction complete all as specified and directed.

S&F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, supplying & fixing in openings as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) considering of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rails on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed togeather with solvent cement, fixing in the frame at site complete all as specified and directed.

M&L for 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as specified and directed by Engineer-in-Charge.

S&F 30 mm thick, 2nd class hard wood, glazed and skeleton shutter, open rebated and prepared to receive glass or gauge without sash bars , divided in to squares and edges of framing plain chamfered or rounded, fitted with cut or mitred beads for securing glass or gauge etc as specified in SSR Part-I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 30 mm thick Flush door shutters solid core construction with block board core and ply wood face pannels commercial veneered on both faces complete all as specified and directed.

S&F powder coated aluminium frame (minimum thickeness of powder coating 50 Micron) for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F steel window with side hung shutter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, devotailed or welded complete all as specified and directed by Engineer in charge.

S&F 3mm thick sheet glass ordinary quality & glazing with oil putty or fitted with wooden beads in squares n.exc. 0.50 sqm in each pane complete all as specified and directed.

S&F 3 mm thick frosted on one side sheet glass ordinary quality & glazing with oil putty or fitted with beads in squares n.exc. 0.50 sqm in each pane complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed

S&F Mild Steel Butt hinges, medium weight, cold rolled, 100mm size ISI Marked complete all as specified and directed.

S&F Mild Steel Butt hinges, medium weight, cold rolled, 75mm size ISI Marked complete all as specified and directed.

S&F Extruded aluminium anodised bow handles of 150 mm length etc complete all as specified and as directed.

S&F mild steel pressed handles oval type stove enamelled black of 150 mm length etc complete all as specified and as directed.

S&F mild steel barrel tower bolts stove enamelled block with bright bolt of 200 mm length complete all as specified and as directed.

S&F 300 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section of 200 mm length complete all as specified and directed.

S&F 300 mm mild steel sliding door bolt, plate type stove enamelled black, with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and directed.

S&F aluminium floor door stopper (100mm long) of aluminium alloy body and tongue. Anodised with hard drawn steel spring complete all as specified and directed.

Taking up or down steel tubing with connections of 15 mm bore pipe including cleaning for refixing or removal from site with all fittings complete all as specified and directed.

Taking up or down steel tubing with connections of 20 mm bore pipe including cleaning for refixing or removal from site with all fittings complete all as specified and directed.

S&F GI tubing 15 mm dia medium grade with all necessary GI fittings, fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F GI tubing 20 mm dia medium grade with all necessary GI fittings, fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F in repair Rotational moulded HDPE polyethylene 500 ltrs capacity water storage tanks three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

S&F in repairs Vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including PVC water closet seat cover closed pattern with flat bottom and cover with PVC hinge device, flushing pipe, fixing bolt for pedestal pattern and making good to disturbed surfaces of floor etc complete all as specfied and directed. Make:- Jaguar Cat Part No:-LYS-WHT-38851PSM or equivalent make of Parryware / Hindware/Cera.

S&F in repair Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat aprt no. 4645 IRIS or equivalent make of Cera/Jaquar/Parryware/ Hindware.

S&F in repair PVC (Plastic polymer flushing Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as directed by Engineer-in-Charge .Make:- Prayag cat aprt no. 503 or equivalent make of Pearl/ Hindware.

S&F in repairs CP Bib tap 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.7606 or equivalent model from make:Cera/Jaguar/Parryware

S&F in repair Pillar tap,15 mm bore, brass chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge Make:- Prayag cat part no.7602 or equivalent make Hindware / Sona.

S&F in repairs CP Stop cock ( concealed type) ,15 mm bore, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.9218 or equivalent model from make Sona / Hindware.

S&F in repair PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.

M &L for Cutting chases, pinning in concrete block work, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

S&F in repair PVC (SWR) floor trap 75 mm dia outlet, plain with grating including jointing with solvent cement etc complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint laid in trenches/floors complete all as specified and directed.Make:- Prince / supreme.

S&F in repair 75 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joint laid in trenches/floors complete all as specified and directed.Make:- Prince / supreme.

S&F in repair 110mm bore PVC (SWR) bends /door bend of any radius with cement solvent, cement joints, complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) bends /door bend of any radius with access door with cement solvent, cement joints, complete all as specified and as directed.

S&F in repair 75mm bore PVC (SWR) bends /door bend of any radius with access door with cement solvent, cement joints, complete all as specified and as directed.

S&F in repair 75mm bore PVC (SWR) bends /door bend of any radius with cement solvent, cement joints, complete all as specified and as directed.

S&F in repair 75mm bore PVC (SWR) vent cowl complete all as specified and as directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep in soft / loose soil etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Hardcore of crushed stone, gauge n exc 63mm, deposited, spread and levelled well in layers n exc 15cm thick, watered and rammed to a true surface etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Sand filling under floor including watering and well ramming for laying of interlocking paver blocks complete all as specified and directed by Engineer-in-Charge.

M&L for Machine pressed pre-cast concrete polished rubber moulded coloured interlocking paver block of any shape and size conforming to IS : 15658-2006 , 60mm thickness, M-35 grade of approved design jointed with grey cement and pigment etc complete all as specified and as directed.

M&L for machine pressed pre polished factory made pavement chequered cement concrete tiles of size 300 X 300 X 25 mm thick of approved design and colour , set jointed and pointed in neat cement slurry with grey cement and pigment over and including 15 mm thick screed bed in cement sand mortar (1:4) complete all as specified and as directed.

S&F in repair CP over head showers dia around 100 mm round shape single flow ( ABS body chrome plated with grey face plate ) with rubit cleaning system with CP shower arm dia 20 mm long round shape without bend for wall mounted showers wall flange etc complete all as specified and as directed. Make: Jaquar Cat.No OHS-CHR-1989 with SHA-CHR-49483 or equivalent model from make Hindware / Prayag.

M&L for Synthetic enamel paint two coats over a coat of pink primer on new or previously untreated wooden surfaces over 10 Cm width or girth including necessary preparation of wooden surfaces complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying three coat of white wash complete all as specified and as directed by Engineer-in-Charge.

M&L Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of Creosote complete all as specified and directed.

M&L for preparation of newly or previously undecorated plastered surface and applying oil bound distemper two coats over one coat of wall primer over and including 1 mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge.

M&L for weather coat (exterior emulsion) two coats over a coat of alkali resistant primer on external surfaces including complete removal of existing treatment of walls, preparing the surfaces even & smooth by rubbing with wire brush or sand paper complete all as specified and as directed by Engineer-in-Charge.

M&L for Synthetic enamel paint two coats over a coat of red oxide primer on new or previously untreated steel surfaces exc.10 Cm width or girth including necessary preparation of steel surfaces etc complete all as specified and directed by Engineer-in-Charge.

Supply and laying Sub class 'B' well burnt fly ash brick, laid flat in trenches as protection to XLPE cable complete all as specified and as directed.

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 70x3.5 Sqmm laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed including taking down old unserviceable one etc complete all as specified and as directed.

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 25 Sqmm 4.0 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed including taking down old unserviceable one etc complete all as specified and as directed.

M&L for cutting existing bituminous road surfaces not more than 150 mm thick removing for laying of pipes/cables, making good with PCC 1:3:6 type C1 20 mm graded aggregate to match with the adjacent surface. complete all as specified and as directed by Engr-in-Charge. Note: Excavation and earth work below 150 mm thick will be measured and paid under relevent items.

S&F GI tubing 50 mm dia light grade with all necessary GI fittings, fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

Supply, fixing , testing and commissioning of CPRI approved factory made outdoor type, LT distribution feeder pillar IP-65, suitable size totally enclosed dust and vermin proof, double leaf shutter in front and single leaf shutter in rear made out of 3.15mm thick CRCA sheet duly fabricated and having proper front and rear locking arrangements duly painted with powder coated paint and aluminium bus bar 300 amps , 415 volts , 50 Hz 3 phase and 4 wire system with the following items connected as under including supplying and fixing on MS channel 75x40x5mm in PCC foundation and PCC work around the panel board withinn two feet area complete all as specified and as directed by Engr-in-charge. with the following accesories: (a) Change over switch 200 Amps 415 Volts - 01 (b) MCCB 4 pole 250 Amps, 415 V, 35 KA.=01 No (c) LCD multifunctioning meter =1 Nos. (d) Phase indicator Lamps (RYB phases) -01 Set (set of three) LED cluster type. (e) CTs 100/5 amps- Set of three (d) Aluminium Bus bar 300 AMps - 03 Nos and 150 Amps -01 Nos (e) Internal wiring for panel incl insulators, sleeves etc. Note: Bidder quoted rate shall be inclusive of S&F of the components from (a) to (e) alongwith feeder pillar box.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to Aluminium strip of size 25x3mm by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 32mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including taking down old one and necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I complete all as specified and as directed.

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed, ie.(Note: two run of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR kabel/Havells/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Material and labour for sub main wiring with four single core 10.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and two single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 10.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed.(Note: four run of 10.0 sqmm cable , two run of earth wire of 10.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR kabel/Havells/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 16.0 Sqmm 4 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed.

Supply and fix MCCB Distribution board, TP&N , vertical , double door, 50 Hz with IP-43 protection,sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link and one No. MCCB 125 Amps 25 KA for incomer,415 Volts 4 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Havells/Schnieder/GE/C&S/L&T.

S&F MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with necessary electrical connection complete all as specified and directed . Make: Havells /Legrand / Schneider /L&T/GE

Supply and fix MCCB four pole , 415 Volt, 100-125 Amps,25 KA rupturing capacity , adjustable thermal & fixed magnetic setting with sheet metal enclosure complete all as specified and directed.Make: Havells Cat Part No.IHMCAABTO 125# and MCCB sheet metal enclosure Havells Cat Part No-IHEPPE or equivalent make of Legrand / C&S / Indoasian / L&T .

S&F MCB DP, 240 Volt, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed .Make:- Havells cat part no.DHMCCDPF006-32 or equivalent model from make:- Hager/Schneider / Siemens / Legrand / Indo Asian .

S&F MCB SP, 240 Volt, 6-40 Amps fixed in DB's complete all as specified and directed .Make:- Havells/L&T/Indo Asian

Supply & fix in repair temper proof digital electric energy meter (KWH) of accuracy class 1.0 AC Single phase, 240 volts, 50 Hz of rating 5A-60A Backlit LCD display with transparent hinge type box (measures and displays KWH, V, Current I, KW, pf last month history of KWH, MD in KW with special features like TOD, temper logging, optical communication port display in absence of power) fixed on wooden / PVC board complete all as specified & directed by Engr-in-Charge. Make :L & T Cat Part No-WM101BC5DLO. Note: Old dismantled energy meters to be deposited in MES store.

Supply & fix in repair three phase temper proof digital electric energy meter (KWH) of accuracy class 1.0 AC Thrree phase, 3X 240 volts, 50 Hz of rating 5A-60A counter type LCD display with transparent hinge type box fixed on wooden / PVC board complete e all as specified & directed by Engr-in-Charge. Make :L & T Cat Part No-WR301BC8D10. Note: Old dismantled energy meters to be deposited in MES store.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, lamp holders, regulators, switch, socket outlets, bell push, ceiling rose etc , removing material to store for keeping in safe custody for reuse at site and making good to disturbed surfaces of walls with cement sand mortar (1:6) and white/colour wash to match with existing surfaces etc complete all as directed.

M&L Point wiring with single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked) as continuous earth wire terminated in and including sunken box for following type of point wiring including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge for one light point / one fan point etc on independent board controlled by one one way switch etc complete all as specified and as directed.

All as per item No 131.00 above but for one 2/3 pin socket outlet 5/6 Amps point on same board etc complete all as specified and directed.

All as per item No 131.00 above but for one 2/3 pin socket outlet 5/6 Amps point on independent board etc complete all as specified and directed.

All as per Item No. 131.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5 Amps complete all as specified and directed.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed.

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 5/15 Amps, flush type, 240 volts complete all as specified and as directed.

Supply and fixing in repair LED batten fittings 1x18 Watt complete pre wired fixed to wall with 2 nos PVC block of suitable size etc complete all as specified and as directed. Make Bajaj Cat Part No BCLSB 18 WH or crompton cat part no LCTL- CDL-18 equivalent make of Philips / Havells.

S&F in repair Decorative wall mounted LED batten fittings with all accessories, 1X 10 Watt, extruded aluminium heat shrink type and provided for efficient heat dissipation and integrated electronic driver and fixed to wall with 2 Nos PVC block of suitable size complete all as specified and as directed Make :- Crompton /Bajaj / Philips..

Supply and fix and testing of storage type , electrically driven ,ISI Marked, water heater (Geyser) of capacity 25 litres, vertical type, wall mounted, BEE 5 star rating , AC, single phase including necessary fixing arrangements , electric and water connection complete all as specified and as directed. Make:- Havells Cat part no. GHWASEIB025 or equivalent make in Racold / Bajaj/LG .

S&F heat resistant PVC connection pipe for hot and cold water 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed. Make: Prayag/Polytuf/Havells/Sona

S&F CP Bib tap 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.7606 or equivalent model from make:Cera/Jaguar/Parryware

S&F CP angular Stop cock ,15 mm bore, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.8010 or equivalent model from make Cera/Jaguar/Parryware

S & F Exhaust fan 230 volts , 250mm sweep ,plastic body including making all electric connection including cutting of hole on brick or block wall and making good disturbed to disturbed surface of wall with cement sand plaster (1:4) and painted / colour wash to match the existing to the true satisfaction of Engineer in charge, necessary and outer wooden box for fan fix on wall etc complete all as specified and as directed. Make :- Havells cat part no. ventil air DX White or equivalent make of Bajaj / Philips.

S & F Exhaust fan 230 volts , 450mm sweep ,metal body heavy duty 1400 RPM including making all electric connection including cutting of hole on brick or block wall and making good disturbed to disturbed surface of wall with cement sand plaster (1:4) and painted / colour wash to match the existing to the true satisfaction of Engineer in charge, necessary and outer wooden box for fan fix on wall etc complete all as specified and as directed. Make: Turbo force SP

M & L for assembly and errection of GI sheet with C&SS rectangular/Square duct made out of L shaped hallow profile, duly factory boxed, including fan housing system, Flex duct, wall termination with suitable load GI support strap every 3 ft all accessories such as coner, cleat, carriage bolts, Gasket and appropriate sealant on longtidunial joints etc complete of size 26 guage suitable Exhaust fan 450mm complete all as specified and directed by Engineer in charge.

S&F in repair LED security building light LED 25 Watt, pressure die cast aluminium housing, heat resitant glass, IP65 protection, better optics for uniform distribution complete with all accessories internally prewired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete all as specified and directed. Make Bajaj Cat Part No-169821 LED/CG or equivalent model from make : Surya/Havells

S&F in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with necessary electrical connection complete all as specified and directed . Make: Havells/ Legrand / Schneider /L&T

S&F in repair MCCB Distribution board, TP&N , vertical , double door, 50 Hz with IP-43 protection,sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link,415 Volts 4 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Havells/Schnieder/GE/C&S.

Supply and fix in repair MCCB TPN , 240 Volt, 100 Amps,16 KA rupturing capacity , adjustable thermal & fixed magnetic setting complete all as specified and directed.Make: Havells / Schnieder / GE / C&S / Indoasian / L&T / Legrand.

S&F in repair MCB DP, 240 Volt, 40 Amps, 10 Ka rupturing capacity 'C' series fixed in DB's complete all as specified and directed .Make: Havells/Schnieder/GE/C&S.

S&F in repair MCB SP, 240 Volt, 6-32 Amps fixed in DB's complete all as specified and directed .Make:- Havells/L&T/Indo Asian

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed including taking down old unserviceable one., ie.(Note: two run of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR kabel/Havells/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

M&L for testing,shifting, installation at new location of installed RO plant 250 Ltrs by dismantling all connected item i.e RO filter, membrane, media filter, water and electric connection, control panel, UV system, tank, reserve tank etc, and fixing in new location with complete servicing of all RO plant item and connected to water and electric connecing complete all as specified and directed by ENgr-in-Charge . Note: Rates for extra pipe/Cable and damage item as required for shifting of RO plant are included in quoated rate.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I complete all as specified and as directed including taking down old unserviceable one.

M/s J. C. CONSTRUCTION

S K Construction

MS HO Shadap

HAMZA CONSTRUCTION CO