Construction of thirumana mandapam at peruvallur

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Plain cement concrete 1:5:10 (One cement, five sand and ten hard broken granite stone jelly) using 40mm HBG metel as foundation concrete including dewatering wherever necessary and laid in layers of not more than 15cm. thick complying with std specification.

Providing and laying in position, Standardised Concrete Mix M20 Grade in accordance with IS 456:2000 using 20mm and down graded hard broken granite stone jelly for all rcc works with minimumm cement content 325Kg/m3 and maximum water cement ratio of 0.55, including admixture(plasticiser/super plasticiser) in recommanded proportions as per IS 9103 to acclerate, retard setting of concrete, improve workability with out i paring strength and durability with about (5 cum) 7730 Kg of 20mm machine crushed stone jelly and with about (3.3 Cum) 5156 Kg of 10 12mm machine crushed stone jelly and with about (4.79cum) 7670 Kg of sand, but excluding cost of reinforcement grill and fabrication charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc and providing fixtures like fan clamps in RCC floor/ roof slabs wherver necessary without claming extra complete complying std specification and also directed by departmental officers. The coarse and fine aggregates to be used should comply with requirements of IS standards(No Seperate payment will be made by the department for excess usage of materilas).

a)For foundation and basement

b)Super Structure(Ground floor)

b)Super Structure(First floor)

b)Super Structure(Second floor)

Centering for soffits of reinforced cement concrete slabs, plain surface including strutting 3 meter height using MS plates of size 90cmx60cm and 10 gauge stiffen and with welded mild steel angles of size 25x25x3mm laid over silver oak (Country wood)

For grade beam basement

For Roof slab plain surfaces

For Column and sunshade

Supplying , Fabrication and placing in position of M.S. or RTS rods reforcement grill in position for all RCC works including cost of steel rods and binding wire etc., complete

Brick work in cement mortar 1:5 (one cement and Five sand) using country bricks of size 8 ¾”x 4 1/4”x2 ¼” including curing, scaffolding etc. complete complying with std. specification.

For foundation and basement

Brick work in cement mortar 1:6 (one cement and six sand) using country bricks of size 8 ¾”x 4 1/4”x2 ¼” including curing, scaffolding etc. complete complying with std. specification.

For super structure(Ground Floor)

b)Super Structure(First floor)

b)Super Structure(Second floor)

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Providing granolithic floor finish of the 40mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. Dadooing with printed design colour glazed tiles of size 300 x 450 x 8mm

Flooring joint free rectified glazed antiskid with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with vitrified tiles of size 600 x 600 x 8mm laid over 20mm thick cement mortar 1:3 Base morar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3Kg / sq.m etc., complete complying with standard specification.

Flooring with kotta slab of size 600 x 600 x 8mm laid over 20mm thick cement mortar 1:3 base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3kg. / sq.m etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved patern, keeping the surface constantly wet sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the departmental officers.(Second floor)

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Paving the floor with concrete anti-skid tiles to Required shape and design of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works).

Paving the floor with concrete anti-skid step tiles to Required shape and design of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works).

Teak wood wrought and put up for frames of doors and windows including all its necessary items etc std specification.

Supplying and fixing teak wood temple type including all materials, labour charges for manufacturing and fixing I position including all furniture fittings etc complete with std specifications.

Supplying and fixing solid core particle board flush shutter of nominal thick of 35 mm with necessary T.W. internal lipping conforming to IS 2302 with both sides alround Teak ply 3mm thick including supplying and fixing cost of wind appliances and furniture fittings such as 1no .300x12mm aluminium tower bolt 2nos. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers.

Supplying and fixing PVC sliding door with Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames, 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter including slidng arrangements.

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from theprofile the size of outer frame 60mm x 58mm andshutter profile are einforcement with GI/1mm 125GSMand 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The PDMrubber (black colour) covered with over all the edges offrame and shutter the shutter will be provided withEspag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the xecutive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)Louvered Ventilators of from the profile the size of outerframe 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chamberedsections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing mild steel grill Gate including cost conveyance of all materials and fixing in position including priming coat etc complete with standard specifications.

Painting two coats over new iron works using ready mixed enamel paint including cost and conveyance of paint and all labour charges etc complete.

Painting two coats with cement paint of first class quality and approved colour, including priming coat and through scrapping and clean removal of dirt etc., complete as per standared specification.

Painting two coats of newly plastered wall surface with Water based Exterior emulsion paint of first class quality and of approved colour over a priming coat including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supplying and fixing of the following dia Ø PVC pipes of ‘B’ class pipe for soil line with necessary specials including the labour charges etc complete the std specification best approved variety and as directed by the departmental officers.

110mm dia

75mm dia

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and filling of following size of HB jelly including the labour charges etc complete the std specification.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110mm dia

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the TW

(a)Drilling of 140/150mm dia pilot bore first depth from 0 to 60m

Reaming of 140/150mm dia pilot bore to 200mm dia bore by heavy weight rigs etc all complete as per standard specifications

Supplying of the following dia pvc pipes of best and approved brand and quality including transporting the pipes to the site etc all complete.

200mm Dia slotted PVC pipes

Labour charges for inserting 200mm dia PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC coupler with cement paste etc complete supply and packing the annular space with pubbles of sie and quality as per standard specification for bore well pipes errected.

Supplying and fixing of 2HP submircile pumpset multistage as per std specification.(The GI specials should be got approved by the Executive Engineer concerned before use on works.)

Supply and fixing run of 4X6 Sqmm(84/0.3) PVC inslutated SC unsheathed Cu.conductor of 1100 V on 7/20GI bearer wire for service connection mains

Supply and fixing of 50mm dia PVC Asward flexiable hose for submercible pumpset.

Supplying, laying and jointing UPVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used for commercial applications operate and designed to handle higher water pressure of approved quality and best variety of 'B' class pipe of the following sizes including fixing wherever necessary with necessary scaffolding charges.The PVC pipes shall be got approved by Executive Engineer before use on works

a)40mm dia PVC pipe

b)32mm dia PVC pipe

c)25mm dia PVC pipe

Supplying and fixing of Brass Chromium Plated screw down tap heavy tyoe 20mm dia of approved make conforming to I.S.specifications and quality including cost of shellac , thread etc.complying with standard specifications and including cutting and threading wherever necessary (Taps should be got approved by the executive Engineer before use on the work.

Supplying and fixing of PVC specials of approved quality and good veritay of the following sizes incluing necessary cutting and threading of GI pipes for jointing etc complete.,

40mm dia Elbow

32mm dia Elbow

25mm dia Elbow

32mm dia tee

25mm dia Tee

40mm dia Coupling

32mm dia Coupling

25mm dia Coupling

32mm dia Balvalve

25mm dia Balvalve

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall 3mm thick hylum sheet cover with T.W. switch box and 5A F/T switch and making good of the concealed portion with suitable colour for PVC concealed light / Fan point.(4Pt / Coil)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150mmx100mmx113mm TW switch box with 3mm thick Hylem sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.

Supply and fixing of 8 W LED lamp for BH point .(MR)

Supply and fixing of single box type 1X18 W 4 feet LED light fixture with led with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 48W LED street light fittings with high power complete with 32mm dia G.I pipe (Class "B") with 1 No 32mmdia GI Bend complete on the existing post / wall with 16A Aerial fuse unit on MS plate with PVC unsheathed copperleads MS clamps and aluminium painting with CFL

Supply an fixing of 1200 mm (48") AC ceiling fan (High Speed) complete with stepped electronic 300W regulator with 1m down rod on the existing clamp

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of 3 Nos. 5Amps (3 Pin and 2 Pin) combined flush type wall socket with control switches concealed in suitable TW Box covered with Hylem sheet in flush with wall with earth connection (For Computer Plug Socket)

Supply and fixing of 5A/15 A 3 pin combined flush type wall socket with 15A flush type switch concealed in suitable T.W Box in flush with wall with 3mm thick hylem sheet.

Supply and fixing of 25 A flush type wall socket with 25 A SP MCB in suitable sheet steel enclosure like Havells / equivalent in flush with wall with earth connection.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure Distribution board with Double Door and 1No32 Amps DP MCB as incoming and 10 Nos 6 Amps to 32Amps SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like legrand make)

supply and fixing of vertical type 4 way triple pole netural MCB distribution board double door type with 40A 4 pole MCB isolator as incoming , 12 Nos 6 to 32 A SPMCB asoutgoing inflush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like legreand make)

supply and fixing of Vertical type 8 way triple pole netural MCB distribution board double door type with 63A 4 pole MCB isolator as incoming , 5 Nos 32 A TP MCB and 9 Nos 6 to 32 A SPMCB asoutgoing inflush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like legrand make)

Supply and fixing of 63A TPN MC switch with suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 32 A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only

Renewal by supply and fixing of 63A Change over switch with suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (For 5 A pulg set)

Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (For 15 A plug and 29 A plug)

Supply and run of 4 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour (For three phase Grinder)

Supply and run of 4 of 6 sqmm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour (For three phase DB)

Supply and run of 4 of 10 sqmm (140/0.3)PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (for EB board 8way tpnpb)

Supply and run of 4 x 10 sq.mm (140/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V on 2 runs of 7/20 GI bearer wire top and bottom of over head for service connection mains(for EB pole to building bearer wire)

Supply and run of 4 x 10 sq.mm (140/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 32mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains (For service pipe)

Supply and fixng of TNEB Moter Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units (500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete

Supply and fixing of 3 Phase 63 A aerial fuse unit for 3 Nos 63 A fuse units (500V) on suitable MS sheet covered with 6mm thickhylem sheet on suitable angle iron work the tapping pole with necessary clamps.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mmx50mmx6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 1 of No 8 SWG copper wire in suitable PVC rigid pipe on wall and ceiling for earth connection.

sub total

dharani constructions