Special repair to building No.23 at Kanpur Proof Range and Provision of toilet at QAO Office (Proof range) at SQAE(SA).

Amount

Demolition of cement concrete as in ground floors and pavings not exceeding 15 cm thick below or above ground level (unreinforced).

Taking down cement plaster including raking out joints, hacking for key, scrubbing down with water all as specified.

M&L for 15mm thick rendering in cement mortar 1:4 as on brick or concrete walls surfaces. finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:6 as on brick walls finished the surface even and smooth w/o using any extra cement all as specified.

M&L for 10mm thick rendering in cement mortar 1:4 as on ceiling and finished even and fair without using extra cement complete all as specified and directed..

Supply only water proofing compound (ISI marked ) complete all as specified and directed.

M&L for preparing old plastered / un-plastered surfaces or previously treated surfaces by removing all dust, dirt and loose scale of lime wash and other foreign materials, removing of oil and grease marks including growth of moulds, moss and then applying two coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Complete removal of existing treatment i.e. white wash / colour wash, distemper etc. of any description from walls complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls including cornices, pillaster etc. and applying two coats of white wash complete all as specified and directed.

M&L for preparation of plastered surfaces of walls including cornices, pillaster etc. and applying two coats of exterior emulsion paint over one coat of primer height n exc 6.0 mtrs complete all as specified and directed.

M&L for prepration of surfaces by applying jk/birla wall care putty and rubbing &making the surface smooth by using embbray paper complete all as specifird and directed

M&L for applying two coats of oil bound distemper on prepared surfaces all as specified

M&L for preparation of new wooden surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel or iron surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat zink chrome red oxide primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old steel or iron surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for 50mm thick in cement concrete 1:3:6 type C2 using 20mm graded stone aggregate in plinth protections/ path including necessary form work complete all as specified.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in floors, finished even and rough to receive floor topping complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for glazed ceramic joint free coloured / printed tiles of size 450 x 300 x 6-7 mm thick on vertical surfaces; set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tile over and including 10 mm thick cement plaster in cement mortar 1:4, finished even and fair to receive tile etc. complete all as specified and directed.

M&L for non skid ceramic jointfree printed coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc; set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tile complete all as specified and directed.

M&L for 18 to 20 mm thick Black granite as in platform, shelves etc; machine cut, bedded and jointed with grey cement slurry including cutting and polishing and all exposed edges to be bull nosed or half round by cutting, grinding and polishing etc incl making of hole for gas pipe line. complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab in floors ,setand jointed in neat cement slurry and pointed in coloured cement to match over 25 mm thick pcc 1:2:4 & 20mm thick screed bed in cm 1:4 complete all as specified and directed.incl dismantling of pcc

Ditto same as per item no 25 but on vertical surfaces in cl 10 mm thick cement plaster in cm 1:4

Taking down chowkhats or frames not exceding 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

All as per item No. 27 here in before but exceeding 1.5 Sqm but not exceeding 4 Sqm each.

S& F pressed seel frames size125x60mm for doors with one or more rebates including necessaey fixing lugs, hinges, lock strike plate, etc., incl pcc 1;2:4 filled in hallow portion complete, as specified, supplied and fixed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type , both face is covered with decorative face veneer with lipping/frame to match, complete all as specified and directed.

S&F of 300 mm long aluminium anodised sliding door bolt with hasp and staple and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F of 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F of 200 mm long barrel tower bolt aluminium anodised of extruded section and fixed complete all as specified and directed.

S&F for stainless steel wire cloth of 0.36 mm dia of wireand average width of aperture 1.40mmfixed with stainless wire staple complete all as specified and directed.

S&F for 35 mm thick second class hardwood, glazed and skeleton shutter, open rebated and prepare to received glass, gauge etc (with sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc; size of member of shutter as specified in SSR Part-I Section 8 clause 8.24 (b) and fixed to chowkhats complete all as specified and directed.

S&F solid U pvc frame (single rebated of size 100x30mm made out of solid u pvc foam witj homogenous fine cellular structure having smooth outer integral skin with suitable skin with suitable metal stiffner and fixed with 100x 8 sheet metal CSK screws complete all as specified and as shown on drawing as per specification & drawing complete all as specified and directed.

M&L for factory made solid U pvc profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminated on bothsides of approved colour as in fill with C type GI or 40x20x19 of ms pipe as in stiffner & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F of 100 mm size PVC butt hinges of Make: Prayag or equivalent complete all as specified and directed.

S&F of 150 mm size PVC handle of Make: Prayag or equivalent complete all as specified and directed.

S&F of 150 mm size PVC tower bolt of Make: Prayag or equivalent complete all as specified and directed.

Demolition of brick work including all quions, arches etc. built in cement mortar complete all as specified and directed.

M&L for brick work built in cement moratar 1:6 with sub class B bricks straight or curved on plan exc. 6 m mean radius.

All as per item No. 42 here in before but except bricks.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

S&F of steel windows with side hung shutter including box type hinges with steel handle and steel peg stay with glazing bars, dovetailed or welded complete all as specified and directed.

All as per above item no 45 here in before but without glazing bars.

S&F of steel ventilators with partly glazed and partly gauged complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F of 3 mm thick sheet glass, ordinary quality and glazing with putty or fixed with beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

All as per item No. 49 here in before but frosted / pin headed glass.

S&F of mild steel work as in holdfasts, clamps, stays and similar small articles including nuts and bolts complete all as specified and directed.

S&F of 100 mm long butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and directed.

M&L 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work. complete all as specified and directed.

M&L for cutting holes in brick wall exc. half brick but not exc. one brick, built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:4 or cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as specified and directed.

Cutting chases in brick walls for concealed water tubing etc and making good to facing in cement mortar 1:3, cutting chases n. exc. 10 cm girth complete all as specified and directed.

S&F in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repairs continuous (piano) hinges, mild steel, bright finish or electro galvanised with 40 mm width flaps when open complete all as specified and directed.

Demolition of concrete of any description and in any position, not otherwise specifically provided for incl. lime concrete, mud phuska etc complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-I (using 20 mm graded stone aggregate) as in coping and padding concrete etc. complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-0 (using 12.50 mm graded stone aggregate) as in roof, kerbs or mud stops, benching etc; rounded or chamfered angle complete all as specified and directed.

M&L for roof treatment by applying polymeric water proofing membrane of weight not less than 3 Kg per Sqm complete all as specified and directed with and including comprising of following operations:- (a) Preparation of plastered roof surface by cleaning surface free from dust and other foreign materials etc. (b) Applying a priming coat @ 0.40 Kg/ Sqm with bituminous primer to the prepared roof till the surface is properly impregnated and solvent oil in primer shall be allowed to evaporate completely. (c) Applying hot blown bitumen grade 85/25 @ 1.2 Kg/ Sqm over primer and dusted with dry sand and allow to dry. (d) Laying of polymeric water proofing membrane of weight 3 Kg/ Sqm. (e) Applying a coat of hot blown bitumen grade 85/25 @ 1.20 Kg/ Sqm and dusted with dry sand and allow to dry.

M&L for 15 mm thick screed bedding in cement mortar 1:4 on roof, mixed with water proofing compound as per manufacturer instructions over cleaned roof surface, finished even and rough complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately under respective item of Schedule ‘A’.

Dismantling of water storage tank and removing to store of capacity exc. 250 ltrs but n. exc. 500 ltrs complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore complete all as specified and directed.

All as per item no-64 here in before but of 20 mm bore.

Re-fixing old steel tubing and connections in new or old position (wall, ceiling and floor etc) of 15 mm bore including cleaning old tubing complete all as specified and directed.

All as per item no-66 here in before but of 20 mm bore.

S&F of 15 mm bore steel tubing, medium grade, galvanised with all fitting, fixed to walls and ceiling or laid in floor complete all as specified and directed.

All as per item no-68 here in before but of 20 mm bore.

S&F of20 mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in 20 mm bore ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (min wt-210 gram) complete all as specified and directed.

S&F of 500 ltrs capacity triple layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position as specified in SSR Pt –I complete all as specified and directed.

Supply and fixed in repairs vitreous china squatting pan Orissa pattern of size 550x400mm including integral foot rest fixed in position complete all as specified.

Supply and fixed in repairs vitreous china EWC padestal pattern closet with White seat & cover with flat bottom with hanging device complete all as specified and directed.

Supply and fixed in repairs wash basin (550X400mm) vitreous china including cutting for holes pinking in ends of brackets for erecting stand incl waste pipe and waste coupling complete all as specified.

Supply and fixed in repairs vitreous china urinal bowl flat back of size (465x355x265mm) white with grating and union for discharge pipe ( excluding flushing cistern Flush pipe and waste pipe)complete all as specified and directed.

S&F in repairs cast iron floor trap of 75 mm dia, chromium plated grating including jointing to waste pipe with lead joints and fixed in cement concrete 1:2:4, type B-0 (using 12.50 mm graded stone aggregate) complete all as specified and directed.

S&F of PVC connection 600 mm long with brass coupling suitable for 15 mm dia pipe complete all as specified and directed.

S&F syphonic action PVC low level flushing cistern of 10 ltr capacity including internal fittings, brackets,32mm flush pipe etc, complete all as specified.

Supply & fixed in repairs fancy type chromium plated Pillar tpas with capstan head screwed down high pressure with or without lettered 'Hot' or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed.all as specified.

S&F grating around 140mm size of PTMT (minimum wt 50 gms)

Dismantling of 75 to 100 mm dia cast iron pipes, jointed in cement mortar and fixed to wall or laid in trenches and taking out if required complete all as specified and directed.

S&F for 100 mm bore cast iron soil, waste and vent pipes, in any length with or without ears with cement joints fixed on walls with clamps complete all as specified and directed.

All as per item No. 85 here in before but laid in trenches.

S&F for 75 mm bore cast iron soil, waste and vent pipes, in any length with or without ears with cement joints fixed on walls with clamps complete all as specified and directed.

All as per item No. 87 here in before but laid in trenches.

S&F in repairs cast iron bends (any radius) diminishing pieces or tappers (larger bore measured) for 100 mm bore pipe complete all as specified and directed.

All as per item No. 89 here in before but of 75 mm bore.

S&F in repairs chromium plated shower rose& arm with or without swivel joints suitable for fixing to steel pipe of 15 mm bore complete all as specified and directed.

S&F bib taps long body, C P cast copper alloy fency type with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule of 15 mm boreand fixed complete all as specified and directed

S&F in repairs stop valves, chromium plated, cast copper alloy, fancy type with capstan head and cup, screwed down, high pressure, screwed both end, long screwed shank for iron pipe (concealed type) of 15 mm bore complete all as specified and directed..Hindware Cat no F-100011 or equivalent in L&K ,

Demolition of reinforced cement concrete of any description and in any position all as specified.

M&L for precast cement concrete type B1:2:4 reinforced type B1 using 20mm graded stone aggregate as in stair cases lintels RCC chajjas, and sunshade etc..

M&L for Reinforced cement concrete type B1:2:4 reinforced type B-1 using 20mm graded stone aggregate as in stair cases lintels RCC chajjas, and sunshade etc..

M & L for 10mm dia TMT bars cut to length bent to shape as required including binding with mild steel annelid wire not less than 0.90mm dia all as specified.

M & L for 8mm dia TMT bars cut to length bent to shape as required including binding with mild steel annelid wire not less than 0.90mm dia all as specified.

Use & waste for formwork to sides and soffits of shelves, shelves, suspended slab, chajjas including support, overhanging etc. for rough finished surfaces of concrete flat complete all as specified and directed.

S&F of mild steel work as in grills, gratings etc. such as window guard bar, angle iron in door frames, barred iron door and similar work etc; confirming to Fe-290 Gde E-165 including cutting and welding as required complete all as specified and directed.

S&F floor door stopper of aluminium alloy long anodized with hard drawn steel spring fixed length of cover plate 15 cm long all as spd

S&F Harrison rails mild steel chromium plated with fixing brackets stops rollers etc as in curtain rods complete all as specified.

Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in soft/loose soil

Excavating over areas, n exc 1.5m deep & getting out in soft / loose soil

Excavating over areas, exc 1.5m but n exc 3.0m deep & getting out in soft / loose soil

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil.

Spreading & levelling in layers n exc. 25 cm thick & well ramming incl. watering as required

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

PCC 1:4:8 type D2 using 40mm graded stone agregate as in foundation & sub base

M&L RCC 1:1.5:3 type A1 (nominal mix) in slab supported on walls.(m-20)

As per item No. 8 above but in beams & lintel band (M-20)

Brickwork with sub-class `B' bricks Old size in one brick thick honeycomb walling built in CM (1:6)

M&L damp proof course in cement concret 1:2:4 type B0, 40mm thick in horizontal or vertical surface incldg necessary form work using water proofing compound as per manufacturing instructions.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat

M&L form work to edges of concrete flat window cills etc exc 10cm but n.exc 20cm

S&F rolled mild steel framed work as in door or gates or other section with guesset plates rails braces completed drilled for fixing or steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks or hinges etc.

S&F 35mm thick plan framed panelled shutter(two panel) eith lock rail and paneel of 9mm B.M.P. commercial ply or12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003(part 1), kiln seasoned and chemically pressure treate.

M&L solid PVC door frame size 50mmX47mm made out of 5mm plain colour PVc sheet reinforced with MS squire tube all as specified.

S&F factory made solid PVC moulded door shutter 28 to 30mm thick(stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plane colour PVc sheet with particle board core in frame all as specified.

S&F MS sliding aluminium door bolts clip type stove each enammeled black with bright bolt 300mm long all as specified.

S&F butt hinges 100mm size extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21

S&F aluminum pressed handle oval type 125mm.

S&F aluminum tower bolt 200mm long with bright bolt.

As per item No. 123 above but in stirrups.

S&F mild steel ventilator with top hung shutter including hinges steel peg stay complete incl shop coat of zink chromate primer.

M&L for 3mm thick APP modified membrane water proofing treatment an roof slab as specified. (a) the roof surface shall be thoroughly wire brushed washed dried up & cleaned to remove all foreign materials & dust to receive primer. (b) on the dried roof surface apply a uniform coat of bituminous primer T-10/polymerised primer oil based coat @0.30 liter per Sqm. as per manufacturers insruction. (c) on the primed surface the approved APP modified bituminous membrane pre fabricated with non woven polyester mat as reinforcement stabilised with fibre glass strands &top with plain surface 3mm thick weighing not less than 3.5kg/Sqm shal be laid by torch application method.

Hardcore of Broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface

M&L 75mm thick PCC type D-2, (1:4:8) type using 40mm graded stone aggregate as in sub base surface finished fair and even completed all as specified.

M&L for 75mm thick cement concrete type C-1 (1:3:6) per using 20mm graded stone aggregate as in plinth protection etc all as specified and directed by engineer-in-charge.

M&L non skid ceramic colour tiles 7mm thick area of each tile exc 0.11 Sqm but not exc 0.18 sqm in floor set and jointed in neatr cement surrey and point in white cement to match colour tile over 20mm screed in CM 1:4.

M&L Glazed ceramic colour tiles in vertical surface 350X250x7mm/ 450X350X7mm thick laid on 10mm thick cm 1:4 on vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match.

Rendering 5mm thick cement plaster in CM 1:3 on ceiling.

M&L three coats of w/wash to ceilling surfaces incl preparation of surface complete all as specified.

As per item No. 133 above but- but in walls.

M&L two coats of cement base paint over a coat of white wash incldg preparation of new plaster surface.

All as per srl item 135 above but without primer.

S&F vitreous china wash down water closet pan (pedestal pattern) white excluding fixing bolt incl plastic water closet seat cover and mild steel chromium plated fixed in repair.

S&F steel water tubing galvanised 15mm bore, med grade fixed to walls and ceiling or in floor complete all as specified.

S&F steel water tubing galvanised 20mm bore, medium grade fixed with all fittings fixed to wall and ceilling or in floor complete all as specified.

S&F 15mm chromium plated cast copper alloy bib taps.

S&F stop valves, cast copper alloy with crutch or butterfly handles screwed down high pressure screwed both ends for 15mm bore iron pipe or brass ferrule.

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe & waste pipe) complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe grating and union for disharge.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as directed by engineer-in-charge.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls

S&F 110mm dia PVC(SWR) junction single (single T) equal or unequal 110dia.

S&F 75dia PVC (SWR) bends any radius

M&L Cast iron Nahani trap 75mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as directed lby engr-in-charge

S&F PTMT grating doom 100mmdia (minimum 25gms).

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F Towel rail 600mm long chromium plated fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190gms)

Supplying only Integral waterproofing compound

M&L PCC in surface channels and drains type B2 (1:2:4) using 40mm graded stone aggregatein channel of man hole

M&L Concrete bed to 150mm dia drain pipes including packing under, & haunching against the sides of pipes after they are laid & tested; in PCC (1:4:8) type D-2

M&L PVC SWR drain pipes laid in trenches & jointed as specfified of 150mm dia

M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings, cover slabs (for manholes etc.) including form work complete

M&L PCC in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed type B1 (1:2:4) using 20 mm graded aggregate

M&L Makrana white Marble tiles 30cmx20cmx20mm thick machine cut, bedded jointed & pointed with grey cement slurry including cutting & polishing for partition.

M&L for point wiring complete with PVC insulated, unsheathed cable, 1100 volts grade with multistranded copper conductor of 1.5 sq mm (FRLS) drawn through and including PVC casing and caping of suitable size fixed on wall including PVC insulated unsheathed multistranded copper conductor of size 1.5 sq mm (FRLS) as earth continuity conductor and connecting to common earth dolly all as specified for :- (a) One light point control by one switch

One ceiling fan/exhaust fan control by one switch

S & F switch piano flush type one way 5 Amps

Supply and fix ceiling rose three terminal

S & F MCB SP 6-32 Amps

S & F MCB SPN 32 Amps

S & F MCB DB SPN 8 way, 240 volts double door type Make : L&T/Indo Asian/Legrand

Supply and fix LED tube light fitting 22 watts surface and wall mounted, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver along with fixture complete all as specified and directed. Cat No. ENDURALINEARNEOBS22WLED830SPCWH. Make : Havells or its equivalent in GE/Philips

Supply and fix exhaust fan, heavy duty, copper winding, AC single phase 230/240V of size 380 mm sweep with louver. Model : Turbo Force SP, Make : Havells or its equivalent in Bajaj/Crompton

Supply.laying and testing cable XLPE insulated screend PVC bedded, galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core

M&L for sand cushning to U/G cable in layers of 23cm thick( 8 Cm before laying the cable and 15Cm thick after laying the cable) in trenches including watering and consolidation, complete all as specified and directed.

Supplying and laid flat sub class 'B' bricks, old size, laid dry in trenches for the protection of U/G cable, complete all as specified and as directed.

M & L cement concrete in foundations as filling and mass concrete typeB1, 1:2:4 with 20 mm graded stone aggregate complete

Supply and laying in trenches GI pipe light grade 25 mm dia for protection of cable

M & L for cutting extg 50 mm dia GI pipethraing of the cut portion in position and inserting tee of size 50x50x20 mm with Nipple and union 50 mm dia complete all as specified

Supply and lay GI pipe medium grade with fittings of dia 20 mm

Supply and fixing gun metal, globe or gate valves 20 MM dia with iron wheel head, screwed both ends fro iron pipe and fixed.

Taking down old point wiring complete for light/fan/socket(5/15 Amps) bell point etc complete with all light fittings accessories, such as switch sockets 5/15 Amps ceiling rose etc including making good to the disturbed surface to match with the existing complete all as specified and directed by Engineer-in-Charge.

M&L for Point wiring complete with PVC insulated, unsheathed cable, 1100 volts grade with multistranded copper conductor of 1.5 sq mm (FRLS) drawn through and including concealed PVC conduit of suitable size including cahse cutting and redressing of surfaces with PCC and touch painting complete including PVC insulated unsheathed multistranded copper conductor of size 1.5 sq mm (FRLS) as earth continuity conductor and connecting to common earth dolly all as specified for :- One light point control by one switch

One ceiling fan/exhaust fan control by one switch

One 3 pin socket outlet, 5 Amps independent

One 3 pin 5 amps socket outlet on the same board with other switches

One 3 pin 5 Amps socket outlet independent but below the switch board of light board of light points in the same vertical plane.

One bell/buzzer point contolled by one push button independent

ditto as per item No. 2 above but wire 2.5 sq mm cable for switch socket outlet 3 pin 15 Amps with 2.5 sq mm as earth continuity conductor.

S & F socket outlet 2 in 1, 3 pin, 5 Amps

S&F socket outlet 2 in 1, 3 pin, 5 and 15 Amps flush type.

S&F switch piano, flush ype single pole 15 Amps

Supply and fixing electric bell, AC, 230 V, Single pole, multi music type

Supply and fixing bell push flush type 5 Amps

Supply and fixing in repair surface and wall mounted LED batten 20 watts, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with provision PVC copper wire 1.5 sq mm 3 core of required length upto ceiling rose complete all as specified and directed. Cat No. LCCLB24-CDL of Make : Crompton, Cat No. ENDURA LINEAR NEO BS20W LED 830SP CWH of Make : Havells.

Supply and fix in replacement ceiling fan 1200 mm sweep complete with down rod canopy and blades of size 1200 mm sweep,Energy efficient, 5 star rated make Havells. / crompton / Bajaj ( Old fans will be deposited to factory authorities)

Supply and fix in replacement Exhaust fan 300 mm sweep complete with brackets frame and blades, metalic body heavy duty with louvers suitable for 240V 50 Hz supply , make Havells. / crompton / Bajaj ( Old fans will be deposited to factory authorities)

Supply and fix in repair LED roadway luminaire 25 watts with high power, energy saving and environment friendly long life versatile pressure die cast aluminium IP66 with arcylic cover suitale for pole dia 43 mm max complete all as specified and directed by Engr-in-charge. Cat No. LSTS-25-CDL of Make : Crompton, Cat No : ENDURA PEARL SL25WLED757 SASY TOPC of Make : Havells,. Note : Rate quoted by the contractor deemed to be included any addition/alteration of existing brackets suitable for fixing of light fittings and provision of three core twisted wire 0.75 sq mm from light fittings to ceiling rose as and where required complete all as directed by Engr-in-charge.

Supply and fixing in repair TPN DB's 4 way vertical type 415 V, double door suitable for housing of 125 Amps MCCB as main incoming. ABB/Legrand/Schnider

Supply and fixing MCCB 63 Amps, 4 Pole, 16 KA, suitable to be fixed in 4 way TPN DB complete all as specified and directed.

All as per item No. 20 above but of 4 way

All as per item No. 20 above but of 12 way

S & F MCB SP 63 Amps

S & F MCB SPN 63 Amps

S & F MCB SP 40 Amps

S & F MCB SPN 40 Amps

M&L for earthing to switch gear/MCB DB with mild steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to galvanised earth lead wire 4.0 mm dia by means of galvanised iron nuts, bolts and washer, earth lead connected to eqpt as directed, earth plate surrounded with adequate quantity of charcoal dust mixed with common salt to a packed thickness of 15 cm all around the plate including necessary earth work, PCC chamber and reinforced PCC cover made by PCC 1:3:6 type C-1 as in pit chamber and RCC pit cover 50 mm thick precast RCC 1:2:4 type B-1 duly reinforced with 6mm dia MS bar at 150mm c/c both ways with 10 mm dia MS round bar as handle, 20 mm bore GI pipe medium grade for watering and 40 mm dia GI pipe light grade for protection of earth lead up to 3 mtr with funnel, wire mesh etc with and including testing complete all as specified and as shown in electrical plate No 3 of MES sch Part I.

Earthing continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed or any other indicated situation for loop earthing etc. As required 4 mm dia galvanised iron or steel wire.

S & F sub main wiring for circuit of size 6 sq mm 2 runs (FRLS) alongwith earth wire of 6 sq mm single runs of FRLS PVC insulated unsheathed cable, 1100 volts grade with multistranded copper conductor including PVC conduit of suitable size complete all as specified and directed by Engr-in-Charge.

All as per item No. 31 above but of wire 1.5 sq mm two runs and 1.5 sq mm single run as earth wire. (for Bldg street light and siren)

Supply and fix XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 4 core