NIT NO.03 ITEM NO.02

Amount

Providing and planting of Bottle palm ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bag

Construction of Hexagonal Gazebo of 4.3 mtr. Dia Plinth having kavelu design LLDPE Sheet Roof and 6 nos. M.S. Pipe columns with Art Work

Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lifts upto 1.5 m including getting out the excavated soil and disposal of surface excavated soil as directed within a lead of 50 m .All kinds of soil. (i) For Foundation : 4x 0.6x0.6x0.6 =0.86 m3 (ii) For Side Wall : 4x2.4x0.25x 0.12=0.28 m3 Total Excavation: 0.86+ 0.28= 1.14 m3

Supply of 6 nos m.s pipe of 150mm od and 10ft height for column

Supply 6 nos of m.s plate of 6 mm thickness and 9"x9" size for closing pipe at one end of 150 mm od pipe

welding of ms plate of 6 mm thickness to one end of 150 mm pipe

Providing and laying 75mm thick compacted bed of dry brick aggregate of 40mm thick nominal size including spreading,well ramming,consolidating and grouting with jamuna sand including finishing smooth etc. complete as per direction of Engineer –in charge.

Provision and laying in position cement concrete of specified grade excluding and cost of centering and shuttering. All work upto plinth level (a) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size

(b) 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth (a) Cement mortar 1:6 (1 cement: 6 coarse sand)

Steel work in built up tubular(hot finished welded type round,square,rectangular hollow tubes etc.) trusses, seating arrangement etc including cutting,hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washersetc. Complete

Providing and fixing of roofing sheet having kavelu design of 1-3 mm thickness and 2.5 m x 1 m size made up of LLDPE in brown color. Rates shall be inclusive of 30% (approx) wastage incurred while cutting the sheet into desired shapes.

Art work over columns of 8’ height including architectural design, mouldings, arches, shapes (like trunk of a tree, bamboos, rock or any character or element representing culture or tradition) and applying proper texture and paint to the finished surface to enhance the aesthetics.

Providing Sculpture like Man / Woman, Animal, Musical instrument or any character or element representing culture or tradition made in RCC / GRC

Art work over Seats / Benches including architectural design, mouldings, arches, shapes (like trunk of a tree, bamboos, rock or any character or element representing culture or tradition) and applying proper texture and paint to the finished surface to enhance the aesthetics.

Art work over roof by making architectural design, mouldings, arches, shapes (like trunk of a tree, bamboos, rock or any character or element representing culture or tradition) and applying proper texture and paint to the finished surface to enhance the aesthetics.

Art work over floor/wall by making design/texture and applying paint to the finished surface to enhance the aesthetics.

CHILDREN PLAY EQUIPMENTS

MULTI-PURPOSE PLAY SYSTEM (4 Nos. Square deck) SQUARE DECK WITH CANOPY 5’: 3 NOS. Main Pillar Pipes Made Up Of 80 Mm NB "B" Class G.I. Pipes. Height : 1.5 MTR From GL SQUARE DECK WITH CANOPY 3’: 1 NOS. Main Pillar Pipes Made Up Of 80 Mm NB "B" Class G.I. Pipes. Height : 1.0 MTR From GL SWINGING BRIDGE : 1 NOS. 60mm NB G.I. Pipe Used For Main Structure. 1.3Mtr W X 3.0 Mtr Lx1.5 Mtr Ht WAVE SLIDE(1.5 M) : 1 NOS. Wave Slides Made Up Of Fiber Reinforce Plastic Material . 3.0 Mtr Length X 0.5 Mtr Width SPIRAL SLIDE(1.5 M) : 1 NOS. Spiral Slide Made Up Of Fibre Reinforced Plastic Material Height : 2.1 Mtr And 4.0 Mm Thick STEPLADDER : 1 NOS. Step Ladder Molded With Fibre Reinforced Material. 0.4 Mtr L X1.0Mtr W X1.0 Mtr HT ROCK CLIMBER : 1 NOS. Rock Climber Made Up Of Fibre Reinforced Plastic Material. Length 1.8 Mtr And Width 1.0 Mtr BRIDGE : 1 NOS. Plain Bridge Made Up Of Fiber Reinforce Plastic Material. 2.4X1.0X0.15Mtr (Lxwxh). NET CLIMBER : 1 NOS. Main Pillar Pipes Made Up Of 32 Mm NB "B" Class G.I. Pipes. 1.5 Mtr Ht . SLIDE ENTRY : 1 NOS. Slides Entry Made Up Of Fiber Reinforce Plastic Material . 0.9Mtr X0.25Mtr X 0.9Mtr(Lxwxht) Structure Build With CO2 Welding Process With Controlled Parameters. Fiber Reinforce Plastic Mouldings With Resin, Color Pigment CSM Mat. Powder Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

DOUBLE ARCH SWING.LEG SUPPORT :80 MM NB PIPE. SEAT- ANTI SKID RUBBER BELT. BEARING : HEAVY DUTY BALL BEARING. AREA : 6.0 M X 1.5 M. HEIGHT : 2.6 M. TOP BAR :50 MM NB PIPE. SUSPENSION : 6 MM RUBBER COATED CHAIN. In This One Child Can Enjoy The Swing At One Time. The Arch Shaped Side Frame Shall Be Made Of 80mm NB B Class GI Pipe Shall Be Made Up Of 50mm NB B Class GI Pipe. The Frame Shall Be Powder Coated To Give An Aesthetic Look. The Swing Shall Be Made Up Of 10mm Thick Anti Skid Rubber Top The Rubber Belt Seat Shall Be Suspended On 6mm Rubber Coated GI Chairn. The Bail Bearings Shall Be Mounted Inside A Specially Designed Nylon Clamp. Powder Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

SPIRAL SLIDE. LADDER-FRAME- 25M M N B PIPE. HANDRAIL - 20 MM N B PIPE. CENTRE SUPPORT- 50 MM N B PIPE. AREA : 2.5 M X3.5 M. PLATFORM HEIGHT : 2.1 M. CHUTE F R P THE TOPCOAT IS DONE USING THE BEST QUALITY BRAND OR DULY POWDER COATED. Spiral Slide Shall Be Chute Made Of FRP (Fiber Reinforced Plastic / LLDPE (Low Linear Density Poly Ethyline) Having Thickness Of 4mm Slide Center Support Shall Be 80mm NB B Lass GI Pipe. Landing Module Shall Be Supported By 20mm NB B Class GI Pipe. Slide Extension Platform Shall Be Made From FRP / LLDPE. The Railing Shall Be Made From 15mm NB And 20nn NB B Class GI Pipe. All Pipes Shall Be Coated With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

ANIMAL MERRY GO ROUND.AREA : Ø 1.5 M. HEIGHT – 0.8 M. SEAT – ROTO MOULDED PVC ANIMAL SHAPE. MAIN FRAME: 40NB G.I.PIPE. BEARING: HEAVI DUTY BEARING. MS PLATE: 250X10MM. SUPPORT PIPE- 80NB. THE TOPCOAT IS DULY POWDER COATED. The Main Frame Of The Animal Merry Go Round Shall Be Made Up Of 25 & 40 NB B Class GI Pipes. The Stand Shall Be Made In 80 NB B Class GI Pipe. The Whole Structure Shall Be Mounted On Heavy Duty Bearing Shaft Permanently Lubricated With Water Sealant. The Animal Shall Be Made Out Of FRP (Fibre Reinforced Plastic)/LLDPE (Low Linear Density Poly Ethylene). It Shall Accommodate 4 Children At A Time. The Pipes Shall Be Powder Coated To Prevent Rusting. Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

STRAIGHT NET CLIMBER . AREA : 0.5 M X 1.7 M. Height : 2.1 M. The main frame of Straight net climber shall consist of 40 mm NB B class GI Pipe. . - The joint balls shall be made from LLDPE (Low linerar Density Polyethylene)/PP Material wil group screws provision for rope holding.- O hooks of the frame having 50 mm bending dia and rod dia 8 mm. the loop shall be given to through o hooks to get a grip while climbing. Rope used of PP nylon mix type having 22 mm diameter. Coating with pure polymer powder with 7 tank treatment 60 to 70 micron thickness. The holding down/fixing of Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1 Cement : 2 Coarse Sand: 4 Stone Agg. 20 MM nominal Size).

Supply Of Babel Drum (Small Size)Steel Tongue Drum Is Of 300 Mm Diameter With 06 Numbers Laser Cut Tongues Tuned To C-Major Pentatonic. Made Of 316L Mirror Polished Marine Grade Stainless Steel Having Width Of 490 Mm And Height Of 980 Mm. The Body Should Have Drain Hole In Base Body. The Body Should Have Drain Hole In Base Body. The Minimum Weight Is 13 Kg Approximately. The Work Includes Nuts & Bolts For Pole Protection At Platform In Foundation Cement Concrete (1:2:4) Block Size Of 0.45x0.45x0.50m

WAVE LADDER.MAIN BODY :-32 MM N B GI PIPE. SUPPORT :- 25 MM NB GI PIPE. THE TOPCOAT IS DULY POWDER COATED. It Shall Have Main Frame Made Of 32 Mm G.I Pipe With Steps Made From 25 Mm G.I Pipe The Pipes Shall Be Powder Coated To Prevent Rusting And For Aesthetic Look. Coating With Pure Polymer Powder With 7 Tank Treatment 60 To 70 Micron Thickness. The Holding Down/Fixing Of Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size)

Supply and installation of Open Gym Equipment

SEATED PULLER /PULL CHAIR made from “C” Class G.I pipe. DIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height). SAFE AREA:- 1.2Mtr x 3Mtr. Seated puller equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made from “C” Class G.I. pipe. Bottom support is of M.S. round plate of DIA 250 mm & 10mm thickness welded. All linkages are made up of 25NB “C” class G.I. pipe. The handle frame is of 32NB “C” class G.I. pipe. The seat frame is of 32NB “C” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation Cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of from Injection Moulded Plastic LLDPE / HDPE.Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205 2RS1” and “6203 2RS1” permanent lubricated sealed bearing of reputed brand.High tensile steel with galvanized nuts & bolts are used for assembly.Thecirclips used for assembly are of A16. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

CROSS TRAINER /ELLIPTICAL EXERCISER DIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height). SAFE AREA: - 1.77 x 1.2Mtr. Cross trainer equipment made from “C” Class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame Pipes are of 80NB “C” Class G.I. Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of DIA 250 mm & 10mm thick. The Handle Frame is made up of 25NB “C” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To build structure bushes are used which are made from M.S. seamless pipe of 60mm OD With 5 mm thickness. The footrests are made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright .The Bearings used are of “6007 2RS1” “62052RS1” and “62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). A16 , A 24 mm circlips are used for assembly. Bolt M8X16 mm and NY lock nut of M8 made of SS304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

BACK EXTENSION DIMENSIONS: - 1400mm (Length) x 700mm (Width) x 820mm (Height). SAFE AREA: - 2.4Mtr x 1.7Mtr. Back Extension Equipment made from “C” class G.I. Pipe of different NB pipe. (NB stands for Nominal Bore i.e. Internal Diameter of pipe in mm) The main frame is of 50mm NB made from “c” Class G.I. pipe. The Foot resting frame of 32mm NB made from ”c” Class G.I. pipe. The handle frame is of 25NB made from “C” Class G.I. pipe. The seat fitted on the outer frames is made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The foundation used for fixing is consists of 50mm NB made from ”C” Class G.I. pipe.The footrests are made from Injection Moulded Plastic LLDPE / HDPE. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

STANDING SEATING TWISTER. DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height). SAFE AREA: - 3 Mtr x 1Mtr. Seating & Standing Twister equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe. The M.S. round plate of DIA 250 mm & 10mm thickness is welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from “C” class G.I. pipe. The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from “C” class G.I. pipe of 25mm NB.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate fitted on the bottom frame is made up of Injection Moulded Plastic LLDPE / HDPE and supported by M.S. Round Plate of size 300mm diameter&10mm thickness. Closing Caps are made up Injection Moulded Plastic LLDPE / HDPE. The Pins used are made up of DIA 35 mm SAE 8620 bright material. The bearings used are of “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

SKY WALKER DIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height). SAFE AREA: - 2.7Mtr x 1.6Mtr. Sky Walker Equipment made from “C” class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame pipe is of 80mm NB made from “C” Class G.I. Material which is bend at the radius of 250mm.The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle The handle frame is of 25mm NB made from “C” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support. The footrests made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25mm SAE8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball. The bearings used are “62052RS1” are permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A24 type. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

CHEST PRESS . DIMENSIONS: - 2000mm (Length) x 710mm (Width) x 2200mm. (Height). SAFE AREA: - 3.0Mtr x 1.7Mtr. Chest press equipment made up of “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The bottom welded with support of M.S. round plate of DIA 250 mm & 10mm thickness. The connecting pipes are made up from 25NB “C” class G.I. pipe. The handle frame is made up from 32NB “C” class G.I. pipe. To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings used are of “62052RS1” &“62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cer clips used for locking is made up of A24 mm & A16mm. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

ROWER (DIMENSIONS: - 1200mm (Length) x 1000mm (Width) x 920mm. (Height). SAFE AREA: - 1.5Mtr. x 1.5Mtr. Rower Equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in mili-meters.The Main frame is of 80NB “C” class G.I. Pipe welded with M.S. round plate of 250mmX10mm. The handle frame 25NB is made from “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To join the movement frame to main frame connecting links made up from 32 NB G.I. “C” class pipe. The seat fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed tools and dies to have uniform radius of 20 mm with no sharp edges. Pins used of Diameter 17mm are made up from SAE 8620 bright material. The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The P.U. bushes (Stopper) used to avoid the collision. The cir clips used for assembly is of A 16. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1 cement : 2 coarse sand : 4 stone agg. 20mm nominal size)

Providing and fixing Surf Board made from “C” Class GI pipe. The center pipe is of 100mm NB made from “C” class GI pipe, and the bottom support of M.S. plate of 250 mm dia& 10mm thickness is welded at bottom. The handle frame is of 40mm NB & 25mm NB made from “C” class GI pipe. The movement frame is made up of 50mm NB “C” class GI pipe. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” Class GI pipe, M.S. round plate of 250 mm diameter & 10mm thickness, 25mm X 25mm X 3mm M.S. angle. To join the centre pipe & handle frame seamless pipe of 130mm dia& 3mm thickness is used. For the movement, bushes are used & for it 60mm dia with 3mm thickness & 60mm solid bar is used. The footrests is made from FRP/C.I./Aluminum casting material, its sizes are 320 mm X 270 mm & 5 mm thickness. For support of footrest is 200mm X 250mm with 5mm thickness M.S. Plate and 50mm X 50mm CRC Square pipe with 2mm thickness is used. Closing Caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm diameter Harden bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The handles used are of Rubber grip. The Nut Bolts used for assembly is made from S.S. material. The bushes (Stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mm dia. The ser clips used for assembly is of 25 mm dia. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

TAICHI SPINNER ( DIMENSIONS: - 700mm (Length) x 1000mm (Width) x 1280mm (Height). Safe Area:- 1.9Mtr X 1.9Mtr Taichi spinner Equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made up of “C” Class G.I. pipe. The handle movement round frame is made up from 25 NB “C” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB“C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. The pins used are made up of DIA 25 mm of SAE8620 bright material. The bearing used is “62012RS1” & “62052RS1” permanent lubricated sealed bearing of reputed brand. High tensile S.S. nut bolts are used for assembly. Foundation cover Closing Cap is made of Injection Moulded Plastic LLDPE / HDPE. The cer clips used for assembly is of A24 and A11.The nylon bush is used for handle knob. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

SHOULDER BUILDER Providing and fixing Shoulder Builder made from C- Class GI pipe. The Center Pipe is of 100mm NB made from “C” Class GI pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The handle movement frame is of 25 NB & 20 NB made from “C” Class GI pipe. To Join the centre pipe & handle movement frame seamless pipe of 130mm dia& 3mm thickness is used. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” class GI Pipe, M.S. Round Plate of 250 mm dia& 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. Closing caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm dia bright bar. The bearing used be permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly is of 25 mm diameter. The Poly Urethin plastic bush is used for handling. The Gym Equipment shall be finished smooth with a primer coating of at least 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be embedded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)

Supply of sign boards of 0.91 x 0.61m size with support length of 3000 mm. Manufacturing, supplying and fixing of Retro reflective sign boards made of 2 mm thick aluminum sheet face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type – IV of ASTM-D 4956-01 in green and silver white including subject matter, message (bilingual(, symbol and borders etc as per IRC: 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 And fixing the same with suitable sized aluminum alloy rivets @ 20 cm c/c to back support frame of m.s angle iron of size 35x35x5 mm and m.s flat of 25x5 mm along with theft resistant measures, mounted and fixed with 2 nos. clamp of mls flats of size 25x5 mm to a vertical post of 3 mtr height made up of msl pipe of 60 mm n.b welded with two hold fast of m.s angle 25x25x3mm of 30cm length each at bottom and including making holes in pipes, angles, providing & fixing m.s message plate of required size, steel work to be paired with two or more coats of synthetic enamel paint of required shade and of approved brand and manufacture over a priming coat of zinc chromate yellow primer (vertical post to be painted in black/white/grey color) Backside of aluminum sheet to be painted with two or more coats of epoxy paint over an appropriate priming coast including all leads and lifts etc. complete as per drawing, specification and direction of Officer-in Charge

Providing and fixing of Name Board made of MS Sheet 90 X 60 cm. 1mm thick with grame of MS angle 50 X 60 x 6 MM to diagonal braces at the back of the sheet of MS flat 40 X 6 mm. Total height of the board above ground level 2.40 m length of legs below ground 0.30 m enbedded in CC block 1: 2 : 4 (1 Cement : 2 Coarse sand : 4 Graded stoneagg. 20 mm nominal size) 30 x 30 x 15 cm. including excavation and removal of surplus earth within 50 m lead applying priming coat of approved steel primer. painting with synthetic enamel paint of approved quality and lettering with enamel paint of approved color (one side) as per drawing/direction of officer in charge.

Greenz