Annual maintenance contract for Civil works Stage contract for the year 2021-2022 upto ending March 2022.

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil

Filling available excavated earth excluding rock in trenches, plinth sides of foundation etc in layers not exceeding 20cm in depth consolidating each layer by ramming and watering lead upto 50cm and lift upto 1.5mm.

Extra for every additional lift of 1.5m or part thereof in excavation banking excavated or stacked material of all kinds of soil.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.

Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.

Providing and filling of GSB/Nallah Muck from approved source including watering, ramming and rolling in 150mm layer.

Pebble dash plaster upto 10m height above ground level with a mixture of washed pebble or crushed stone 6mm to 12.5mm nominal size dashed over and including fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 Coarse sand) and top layer 10mm cement plaster with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

1:4:8(1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing with.1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size).

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level including curing, excluding the cost of centring, shuttering, and finishing.1:1½:3(1 cement :1½ coarse sand :3 graded stone aggregate 20 mm nominal size

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing & fixing upto floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases etc. including hoisting and setting in position with cement mortar 1:3 (1 cement:3 coarse sand) cost of required centring, shuttering and curing complete :1½:3 (1 cement :1½ coarse sand :3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing with:1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing & fixing upto floor five level precast cement concrete hollow blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:1½:3(1 cement :1½ coarse sand :3 graded stone aggregate 20 mm nominal size).

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete.

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete.

Providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. (1 kg of water proofing material in 50 kg of cement).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

Providing and laying upto floor v level reinforced cement concrete in kerbs, steps and the like including curing but excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platforms.

Shelves (cast-in-situ)

Lintel, beams, plinth beams, girgers, bressumers and cantilevers.

Columns, pillars, piers, abutments, posts and struts.

Stairs (excluding landings) except spiral staircases.

Edges of slabs & bricks in floors & walls. Under 20cm wide.

Above 20cm wide.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth /above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand).

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand).

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:3 ( 1 cement : 3 coarse sand).

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand).

Dry random rubble masonry with hard stone in foundation and plinth: with bond stone (quarry).

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab upto 0.5 sqm). 18mm

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab upto 0.5 sqm). 16mm

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm). 18mm

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm). 16mm

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Imported wood only.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : (Imported wood only).

Providing and fixing 30mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). Imported wood only.

Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). Imported wood only.

Providing and fixing specified pre-laminated medium density board with one side decorative and other side balancing lamination Grade I (exterior grade) in shelves with screws and fittings wherever required, (fittings to be paid separately). Flat pressed 3 layer particle board or graded wood particle board grade-I type-II conforming to IS” 3087 edges to be painted with polyurethane primer. 18mm thick.

25mm thick

Providing and fixing specified pre-laminated medium density board with one side decorative and other side balancing lamination Grade I (exterior grade) in shelves with screws and fittings wherever required, (fittings to be paid separately). MDF board conforming to IS: 14587 edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand.18mm thick

25mm thick

Providing and fixing 30mm thick ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Providing and fixing 35mm thick ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Imported wood.

Providing and fixing 30mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Imported wood.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 20 mm dia ( heavy type)

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 25 mm dia ( heavy type)

Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete.Fixed to steel windows by welding.

Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type).

125x70x4 mm (ordinary type)

100x85x5.5 mm (heavy type)

100x70x4 mm (ordinary type)

75x65x4 mm (heavy type)

75x40x2.5 mm (ordinary type)

50x40x2.5 mm (ordinary type)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. : 250x10mm.

Providing and fixing bright finished brass door latch with necessary screws etc. complete. : 300x16x5 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete: 40mm

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete: 50mm

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete: 65mm

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete: 75mm

Providing and fixing bright finished brass handles with screws etc. complete : 125mm

Providing and fixing bright finished brass handles with screws etc. complete : 100mm

Providing and fixing bright finished brass handles with screws etc. complete : 75mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer, (having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete :

Providing and fixing chromium plated brass handles with necessary screws etc. complete :125mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete :100mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete :75mm

Providing and fixing ISI marked aluminum butt hinges ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125x75x4 mm.

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :300x16 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :300x10mm.

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. Complete.125mm

Providing and fixing aluminum hanging floor door stopper, ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Single rubber stopper.

Twin rubber stopper.

Providing and fixing aluminum tee channels (heavy duty) with rollers, stop end in pelmets as curtain rods.

Providing and fixing magnetic catcher of approved quality in cupboard/wardrobe shutters including fixing with necessary screws etc. complete.Triple strip (Vertical type).

Double strip (Horizontal type)

Providing and fixing powder coated telescopic drawer channels 300mm long with necessary screws etc. complete as per directions of engineer-in-charge.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing in position collapsible steel shutters/gate with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer,

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling hutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover.

80x1.20 mm M.S. laths with 1.20 mm thick top cover

80x0.90 mm M.S. laths with 0.90 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete. Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides.

Stainless steel (grade 304) wire gauze of 0.5mm dia wire and 1.4mm aperture on both sides.

40mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size and top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1mm to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume including cement slurry and curing complete :Dark shade pigment with ordinary cement.

Light shade pigment with white cement.

Medium shade pigment with 50% white cement and 50% ordinary cement.

11.12.4 White cement without any pigment.

11.12.5 Light shade pigment with ordinary cement.

Ordinary cement without any pigment.

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) .Light shade using white cement.

Medium shade using 50% white cement and 50% ordinary cement.

Dark shade using ordinary cement.

Ordinary cement without any pigment.

Tile work in skirting, risers of step and dedo upto 2 metre height, over 12mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. Marble tiles (polished) Raj Nagar.8mm thick

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, polishing and curing complete.

Wooden planking, tongued and grooved in flooring including fixing with iron screws complete: 12mm thick imported wood.

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 500x500 mm.

Size of tile 600x600 mm

Size of tile 800x800 mm

Size of tile 1000x1000 mm

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal / vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gram/m2.

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2.

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.1.60 mm thick with zinc coating not less than 350 gram/m2

1.25 mm thick with zinc coating not less than 350 gram/m2

1.00 mm thick with zinc coating not less than 275 gram/m2

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screws. Budloo wood/ Fir wood.

Imported wood.

Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) :

Providing & applying of plasster of paris putty of 2mm thickness over the plastered surface to prepare the surface even and smooth complete.

Providing and fixing plain, square edged wooden beading 65x12 mm section with screws of approved quality for ceiling 1st class teak wood.

1st class deodar wood

1st class kail wood

Providing and fixing 3mm hard board sheet ceiling of approved quality with necessary nails etc. complete (frame work to be paid for separately). Standard Quality board

Providing and fixing 4.5mm hard board sheet ceiling of approved quality with necessary nails etc. complete (frame work to be paid for separately). Standard Quality board

Providing and fixing thermal insulation with specified wool and density conforming to IS: 8183, 50 mm thick, wrapped in 200G Virgin Polythene bags placed over existing false ceiling and held in position by crisscrossing GI wire.With resin bonded fiber glass wool with density 16 kg/cum

With resin bonded rock wool with density 48 kg/cum

Providing and fixing plained eaves boarding. 2nd class Deodar wood 250x32 mm (nominal size)

2nd class Deodar wood 300x40 mm (nominal size)

2nd class Kail wood 250x32 mm (nominal size)

2nd class Kail wood 300x40 mm (nominal size)

12mm cement plaster of Mix: 1:4 (:1 cement :4 coarse sand)

12mm cement plaster of Mix: 1:6 (:1 cement :6 coarse sand)

15mm cement plaster on the rough side of single or half brick wall of mix: 1:4 (:1 cement :4 coarse sand)

15mm cement plaster on the rough side of single or half brick wall of mix: 1:6 (:1 cement :6 coarse sand)

20mm cement plaster of Mix: 1:4 (:1 cement :4 coarse sand)

20mm cement plaster of Mix: 1:6 (:1 cement :6 coarse sand)

White washing with lime to give an even shade on New work (three or more coats).

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work, over and including water thinnable priming coat to give an even shade

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer.

Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre, two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm).

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Tow or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand & manufacture.

French sprit polishing, Two or more coate on new works including a coat of wood filler.

Lettering with black Japan paint of approved brand & manufacture.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1mm thick.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2mm thick.

White washing with lime to give an even shade :Old work (Two or more coats).

White washing with lime to give an even shade :Old work (One or more coats).

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on old work (one or more coats

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

French spirit polishing, one or more coats on old work

Finishing walls with water proofing cement paint of required shade: Old work (one or more coats applied @ 2.20 kg/10sqm) overpriming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat.

Finishing walls with water proofing cement paint of required shade: Old work (one or more coats applied @ 2.20 kg/10sqm).

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead With cement mortar 1:4 (1 cement : 4 fine sand)

With cement mortar 1:4 (1 cement : 4 coarse sand)

Renewing glass panes, with wooden beadings and nails wherever necessary including raking out old putty : Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm).

Float glass panes of thickness 5.0 mm(weight not less than 12.5 kg / sqm).

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 20mm diameter.

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 25mm diameter.

Providing and fixing M.S. round or square bars at required spacing in wooden frame of windows and clerestory windows

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:1:3:6 or richer mix (i/c equivalent design mix).

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:1:4:8 or leaner mix (i/c equivalent design mix).

Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In mud mortar .

In lime mortar with old mughal bricks

In lime mortar.

In cement mortat.

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) :From brick work in mud mortar.

From brick work in lime mortar

From brick work in cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area of 3 sqm. and below

Of area beyond 3 sqm.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : Of area of 3 sqm. and below

Of area beyond 3 sqm.

Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead : Of sectional area 40 sqcm. and above.

Of sectional area below 40 sqcm.

Dismantling steel work in single sections including dismembering and stacking within 50 meters lead in : R.S. Joists.

Channels, angles, tees and flats.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 meters lead.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm.

For thickness of tiles above 25 mm and upto 40 mm.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead.

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of :G.S Sheet.

Abestos sheet.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 meters lead : Upto 10 mm thick.

Thickness above 10 mm upto 25 mm

Thickness above 25 mm upto 40 mm.

Dismantling precast concrete or stone slabs in walls, partition walls etc. including stacking within 50 meters lead: Thickness upto 40 mm

Thickness above 40 mm upto 75 mm

Taking out C.I. cover with frame from R.C.C. top slab of manholes of various sizes including demolishing of R.C.C. work manually/ mechanical means and stacking of useful materials near the site and disposal of unserviceable materials within 50 meters lead as per direction of Engineerin-charge :

Taking out C.I. cover with frame from R.C.C. top slab of inspection chambers of various sizes including demolishing of R.C.C. work manually/ mechanical means and stacking of useful materials near the site and disposal of unserviceable materials into municipal dumps within 50 meters lead as per direction of Engineer-in-charge.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Preparation of subgrade by excavating earth to an average of 22.5 cm depth, dressing to camber and consolidation with road roller of 8-12 tonne capacity including making good the undulation etc. and disposal of surplus earth upto 50 meters.

Supplying and Stacking at site graded curshed stone aggregate of size. 90mm to 45mm.

Supplying and Stacking at site graded curshed stone aggregate of size. 63mm to 45mm.

Supplying and Stacking at site graded curshed stone aggregate of size 53mm to 22.4mm

Supplying and Stacking at site over burnt brick aggregate of size 120 mm to 40 mm.

Supplying and Stacking at site over burnt brick aggregate of size 90 mm to 45 mm.

Supplying and Stacking at site Stone screening of size 13.2 mm nominal size (Type A).

Supplying and Stacking at site Stone screening of size 11.2 mm nominal size (Type B).

Supplying and stacking at site Red Bajri

Supplying and stacking at site Good Earth.

Supplying and stacking at site Moorum

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening /binding material to fill up interstices of coarse aggregate, watering and compacting to the required density.

Scarifying metalled (water-bound) road surface including disposal of rubbish lead upto 50m and consolidation of the aggregate received from scarifying with power road roller of 8 to 10 tonne capacity.

Providing Retro-reflective regulatory sign board of size 900mm diameter made out of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated lens type retro-reflective sheeting as approved by Engineer-in-charge. Letter, symbols, borders, etc. will be as per IRC:67 with required colour scheme on the boards and with the high intensity grade A. the aluminum sheet to be riveted to M.S. frame of angle iron of size 40x40x4mm. The boards will be fixed to 1 No. 50x50mm square post made of M.S. angle 50x50x4mm, 4m long welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminum sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per directions of Engineer-in-charge.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately). For fixed portion. Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15)

Powder coated aluminum (minimum thickness of powder coated 50 microns)

Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15).

Powder coated aluminum (minimum thickness of powder coated 50 microns)

Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns).

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS:12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in- charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm).

With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

With float glass panes of 8 mm thickness (weight not less than 20.0 kg / sqm).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With Stainless Steel cover plate minimum 1.25 mm thickness.

With brass cover plate minimum 1.25 mm thickness.

Providing and fixing Brass 100mm mortice latch and lock with 6levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminum casement windows fastner of required length for aluminum windows with necessary screws etc. Complete. Anodized (AC 15) aluminum

Powder coated minimum thickness 50 micron aluminum.

Polyester powder coated minimum thickness 50 microns aluminum.

Providing and fixing aluminum round shape handle of outer dia 100mm with SS screws etc. Complete as per direction of Engineer-in-charge. Anodized (AC 15) aluminum

Powder coated minimum thickness 50 micron aluminum.

Polyester powder coated minimum thickness 50 microns aluminum.

Clearing snow (with frost) from Roads, manually using picks and shovels; snow depth upto 150 mm.

Clearing snow (without frost) from Roads, manually using picks and shovels; snow depth upto 150 mm

Snow depth over 150 mm but upto 250mm.

Snow depth over 250 mm but upto 350mm.

Snow depth over 350 mm but upto 450mm.

Snow depth over 450 mm but upto 550mm.

Snow depth over 550 mm but upto 650mm.

Snow depth over 650 mm but upto 750mm.

Snow depth over 750 mm but upto 850mm.

Snow depth over 850 mm but upto 950mm.

Snow depth over 950 mm but upto 1050mm.

Snow depth over 1050 mm but upto 1150mm.

Snow depth over 1150 mm but upto 1250mm.

Galla cutting in compressed snow 150 mm deep and 4 m wide.

Galla cutting in compressed snow 1200 mm deep and 4 m wide.

Providing and fixing of heavy duty box type double action floor spring including cutting and making good the floor ,removing and refixing of door and all repairs.(Godrej or Eddy, Samrat make or equivalent. (3 ply).

Providing and fixing 12 mm thick commercial ply wood with necessary screws and nails, including a coat of approved wood primer on one face, and fixed on wooden/steel frame work excluding cost of frame work but including cost of screws, nails complete job as per direction of Engineer –incharge

Providing and fixing 6 mm thick commercial ply wood with necessary screws and nails, including a coat of approved wood primer on one face, and fixed on wooden/steel frame work excluding cost of frame work but including cost of screws, nails complete job as per direction of Engineer –incharge

Providing and fixing 4 mm thick commercial ply wood with necessary screws and nails, including a coat of approved wood primer on one face, and fixed on wooden/steel frame work, complete as per direction of Engineer –incharge (Frame work shall be paid for separately).

Providing and fixing of aluminum composite panel (ACP) 3mm thick of any colour and design & pattern including cost of adhesive (Silicon Sealant) self adhesive PVC Tapes ,screws etc ,but excluding the Aluminum /Wooden frame work(Alstone Eurobond or equivalent make)

Providing and fixing of wooden cornice of (Triangular shape) including cost of nails, screws and two or more coats of synthetic enamel paint over single coat of wood primer. 40mmx40mm

50mmx50mm

75mmx75mm

Providing and fixing of M.S rod locks Six levers with inbuilt sliding bolt, screws ,nuts (heavy duty) complete of approved quality (Godrej, Link or equivalent make)

Providing and fixing of sign boards/Name plates of different sizes made of 6mm thick P VC sheet with digital computerized letters self adhesive on them in bold form all complete including nails, screws, hanging hooks ,adhesive ,P VC tapes etc. complete job.

Regrinding and re-polishing of floors kota/terrazo/ chips to granolithic finish including cost of all chemicals, hire charges of mechanical equipment required, including cost of rubbing/granding stones, minor repairs to cracks, grouting with cement complete job.

Providing and mixing of accelerator of standard make in cement concrete and in cement mortar.

Providing and fixing of 8mm thick glass shelves of approved quality in shelves, racks complete including the cost of edge moulding, holding brackets, screws, fastners.

Providing and fixing of Plain G.I colour sheet of thickness 0.5mm including cost of nails, screws etc all complete wherever required.

Providing & fixing imported wood of all types to the frames of partition, ceilings, backing including finishing the wood smooth, applying one coat of wood primer and two coats of synthetic enamel paint.

Providing & fixing imported wood for frames of doors, windows etc. sawn and put in position including cost of nails, screws etc.

Providing & fixing M.S powder coated drawer channels 450mm long.

Writing alpha- numeric letter on Steel/Wooden surface with synthetic enamel (length & breadth of letter to be measured) for payment including cost of synthetic enamel.

Providing & fixing transparent polycarbonate sheets to windows, partitions etc of standard make including cost of adhesive, wooden beading/nails. (4mm thick sheet).

Providing & laying quarry muck in layers, rolling with power roller of 8 to 10 metric tonne, including watering, all leads, lifts, taxes, carriage complete job.

Providing & fixing of 18mm thick rubber wood board in racks, almirah's etc.including screws, nuts, bolts etc complete job.

Providing and fixing of hollow section PVC Planks (Paneling) for ceiling /lining tongued and grooved of any colour, design and pattern section of panels 10x165 mm Wallthickness1.00mm ±0.1mm including cost of plain beading/PVC angle beading wherever necessary of size25x25 x1.5mm with screws ,nails etc complete excluding cost of frame work (ceiling joists) quality ,shade and colour approved by Engineer-in- Charge(Duroplast or equivalent make). including carriage from source to site of work complete job.

Repairs to aluminium work for doors/windows by way of dismembering the door, windows, refixing after resizing, replacement of hinges, screws, cleats etc. If any aluminium member to be replaced shall be paid in basic aluminium item, as per SSR.

Providing & fixing of stainless steel sliding lock to glass Almirah's of approved make including all necessary fittings complete job.

Providing & fixing aluminium G-channel for sliding doors with necessary screws, nuts complete job.

Providing and fixing of superior quality imported wooden flooring including the base cushion of 10mm foam sheet and fixed with water based adhesive complete job.

Providing and fixing teak woodply sheets with one side decorative face, on the doors/ceiling/walls with necessary nails/screws adhesive complete as per directions of engineer-in-charge (4mm thick sheet).

Providing & laying of dry stone soling/boulders of required grade/size as per site requirement including watering, ramming, dressing, carriage of materials complete job.

Providing and laying of stone dust filling under floors in layers including watering amd ramming complete job.

Providing and fixing of wood work in different kinds of frames of false ceilings, partitions, trusses and purlins etc. using poplar wood.

Providing & fixing of PVC flexible banners of different sizes with computerized digital printing including fixing the same complete job.

Providing and fixing of colour coated G.S sheet gutters including cost of M.S brackets and necessary screws complete. 150mm wide x 100mm depth.

Providing & fixing superior quality brass door (ornamental) handles with necessary screws (200mm) complete job.

Providing & fixing of ISI marked 19mm thick commercial plyboard of standard make including necessary screws, nails complete job.

providing & fixing of multipurpose locks to cupboards, Almirah's of standard make and manufacture.

Providing & fixing aluminium aldrop of standard make with necessary screws (size 8").

Providing and fixing 12mm thick wooden panelling (TNG) in required design/pattern including the cost of all fittings and fixtures (Imported wood) complete job.

Providing & fixing of vertical blind curtains of any colour/pattern of superior quality with G.I Channel pelmet including manual opening and closing arrangements, nails, steel screws all complete.

Providing & fixing synthetic washable wall paper to walls, ceilings with adhesive, of any colour, design pattern of standard make including cost of adhesive quality/make to be approved by Engineer-in-charge.

Providing & fixing Polyvinyl Chloride flooring of any colour,design, pattern, thickness of sheet not less than 1.5mm, including cost of adhesive, complete job.

Providng and fixing of 10mm thick foam sheets to walls/floors including cost of adhesive etc. Complete job.

Providing & laying levelling compound (cementations material) to floors thickness not less than 5mm complete job.

providing & fixing dull mica/sun mica 0.8mm thick sheet to wooden surfaces including cost of adhesive complete job.

providing & mixing water proofing compound with cement concrete/cement mortar as specified by manufacturer, of standard make.

M/S GHULAM NABI TEELI

M/S PEAKS ENGINEERS AND CONTRACTORS

FAYAZ AHMAD SHAH

MOHD SULTAN RATHER