SPECIAL REPAIR IN BLDG NO NP-07 AND PROVN OF STONE SETT ROAD UNDER GE (SOUTH) MAMUN AT MAMUN MIL STATION

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

M&L for pressed steel frames 125mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faceS ,The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for 35mm thick glazed and skeleton shutters (Factory made) of 2nd class hard wood and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per clause 8.20 (a) of SSR Part-I 2009 (Larger size to be provided) including 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M & L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain pre-painted PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M&L for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain pre-painted PVC sheet ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain pre-painted PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain pre-painted PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, orstainless steel wire staples complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for 3 mm thick Figured glass, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F in repair Glass shelf assembly 55cm long with brass chromium plated bracket guard and railing fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Jaquar Cat part No AQN-7771 or equivalent model in Hindware/Marc.

M&L for stainless steel Butt hinges of size 100 mm fixed with steel screws of appropriate size complete all as specified and directed.

M&L for 250mm aluminium sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section etc complete all as specified and directed.

M&L for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed. complete all as specified and directed.

M&L for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed. complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 150mm etc complete all as specified and directed.

S&F 20mm mild steel drapery rods with 1mm thick PVC wood grain coating including brackets and knobs fixing on windows and floor for hanging curtains complete all as specified and directed.

Complete removal of existing treatment & preparation of plastered surface of walls applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over and including a layer of wall care putty not less than 2mm thick complete all as specified and directed.

M&L two coats of white wash on surface of wall including preparation of old plastered surface by washing rubbing, stopping brooming down with steel wire brushing scrapping down smoke roots, moulds salts and trading oil and greasy spots complete all as specified and directed.

S&F in repair 15mm bore Stop valves fancy type, chromium plated cast copper alloy long shank and exposed part kit with fitting sleeve, operarting lever & adjustable wall flange (concealed type) screwed both ends for iron pipe or for unions complete all as specified and directed. Make : Jaquar Cat part No CON-083FT & CON-083FTK or equivalent of Hindware/Marc.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

M&L for Vitreous china wash hand basin, white, flat back, size 550x400mm (Make : Jaquar Cat part No CNS-WHT-801 or equivalent model in Hindware/Parryware/Somany) including 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated (Make : Jaquar Cat part No FLR-5011N or equivalent model in Hindware/Marc.) brackets, CP waste coupling, 32mm bore PVC waste pipe of min 600mm long & 15 mm bore PVC connections, including cutting for and pinning in end of brackets or erecting stand fixed in repairs complete all as specified and directed.

S&F in repair for Vitreous China urinals, Flat back size 330 x250 x450mm (minimum) white with grating and union for discharge pipe (excluding flushing cistern), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, waste coupling , and Union for discharge pipe. complete all as specified and directed.

S&F in repair stainless steel grating doom 100mm dia fixed in floor complete all as specified and directed.

S&F in repair stainless steel grating doom 100mm dia with waste hole fixed in floor complete all as specified and directed.

S&F in repair for Vitreous china white wash down water closet pan (pedestal pattern) with normal closing seat cover S-trap (Make : Jaquar Cat part No CNS-WHT-553SN or equivalent Cat Part/Model of Hindware/Parryware/ Somany) & hand shower (Health foucet) 8mm dia 1m long flex tube in chrome finish and wall hook with NRV (Back flow preventer) and connection to drain (or out going pipe) (Make : Jaquar Cat Part No ALD-577 or equivalent Cat Part/Model of Hindware/Parryware) and to flush pipe, antisyphonic pipe etc complete all as specified and directed

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

S&F 15 mm bore Stop valves/Angle valve with flange cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises complete all as specified & directed.

M&L for rendering 5mm thick cement plaster on concrete surfaces on ceiling / chajjas in cement mortar 1:3, surface finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises, etc complete all as specified & directed. (Note : WPC shall be measured and paid separately) complete all as specified & directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm IN CM 1:6 & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound in IInd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises, etc complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for Preparation of old wall surface after completed removal of existing treatment and making the surface smooth and applying two coat of cement base paint over a coat of alkali-resistant priming paint complete all as specified & directed.

M&L for Preparation of new plastered surface of external wall and chajjas and making the surface smooth with sand paper and priming the surface with primer as per recommendation of manufacturer for external surface, over primed surface applying two coat of cement base paint complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over and including a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over and including a layer of wall care putty 2mm thick complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection laid in panels and joints filled with mix of bitumen and sand (1:3) by weight, finished the surface even and smooth using extra cement including demolition of damaged plinth protection and removal of debris out off the premises etc complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges tiles 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4), including dismantling existing floor tiles of any type and pattern including cement mortar bedding and removing debris/tiles out off the premises, etc complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 450mmx300mm on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:4), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

M&L for Marble Green/Bhaislana Zebra 18 to 20mm thick (table rubbed and pre-mirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms and like set and jointed in neat cement slurry including pointing in epoxy grout to match marble shade, including making hole for gas pipe including rounding the edges of marble stone , laid over and including 20mm thick screed bed in CM 1:6 including dismantling of existing tiles/stone etc complete all as specified and directed.

M&L for Bees-wax polishing on Old kota surfaces of any description, width or girth including cleaning and preparing the surface complete all as specified and directed.

M&L for Factory made rubberised coloured chequered tiles of size 250x250x25mm thick (using vibro compaction method) with 3mm to 5mm thick topping in white cement and non fadeble glossy pigment set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) surface finished even and rough to receive topping over and including 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub-base, surface finished even and rough including demolition of existing tiles path of any description and removal of debris out off the premises etc complete all as specified and directed.

M&L for Rendering 15 mm thick on brick work or concrete surfaces in CM 1:4 with and including water proofing compound to sunken portion with proper slope towards outside and finishing cement concrete surface even and smooth using extra cement including application of 90 micron polythene film and applying bitumen coating @ 3.00 Kg/Sqm etc complete all as specified and directed. [Note : WPC shall be measured and paid seperately]

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

S&F in repair for PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore complete all as specified and directed.

S&F in repair for PVC connection 15mm size with PTMT nuts of length 450mm long of appoved make complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 1000 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

S&F in repair 20mm bore gun metal gate valve, with cast iron wheel head, screwed both ends for GI pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butterfly screwed down for GI pipe 20 mm dia complete all as specified and directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 50mm x 5mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 50mm x 5mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair 75 mm Cast iron cowl, fixed with cement joints complete all as specified and directed.

S&F in repair for 75 mm Cast iron floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair for 100 mm Cast iron floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair for 100 mm Cast iron nahani/gully trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair for 110 mm PVC (SWR) pipes single socketed in any length with rubber joints and necessary fittings and stack clamp made out of 50mm x 5mm galvanised flat iron fixed with bolt and nutscomplete all as specified and directed.

S&F for 110 mm bore bends PVC (SWR) (any radius) fixed with cement solvent complete all as specified and directed.

M&L for APP modified roof treatment over existing accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification incl. dismantling of old APP treatment complete all as directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufactured by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane, Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap.

M&L for 40mm thick fly ash brick tiles over torched APP membrane with joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement over and including bedding layer of cement mortar 15mm thick in 1:4 using WPC etc complete all as specified and directed. (Note : WPC shall be measured and paid separately)

Supply only Polymer liquid water proofing compound of make Pidilite/Bauchemic/Fosrock, all as specified and directed.

M&L for RCC1:1½:3 Type A-1 using 20mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork including demolition of existing cover slabs of any description and removal of rubbish out off the premises etc complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately)

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed

M&L for 150 mm thick Plain Cement concrete type B-2 (1:2:4 using 40 mm graded aggregate) as in subbase of floor complete all as specified and directed

M&L for Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20 mm graded aggregate) as in kerbs of stone sett road complete all as specified and directed

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. Make of cable : Finolex, Anchor, Polycab (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 72 above but for 5 pin 5 Amp socket outlet point on independent gang box and suitable support frame and cover plate (inner/outer) controlled by one switch 5Amp one way, etc complete all as specified and directed.

All as per Srl item No. 72 above but for 5 Pin 5 Amp socket outlet point on same board controlled by one switch 5 Amps one way on same gang box support frame and cover plate etc complete all as specified and directed.

All as per Srl item No. 72 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 2.5Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S&F Modular Switch 1 way 16 Amps , 1 module etc complete , all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW161 /Legrand Cat Part No 673411/ Schneider Cat Part No P1101.

S&F Modular Socket outlet, 5 pin, multi purpose, 2 module 6/16 Amp, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKCWW163 Legrand Cat Part No 673455 / Schneider Cat Part No P2106.

S&F Modular Switch 1 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101, Legrand Cat Part No 673401, Anchor Roma Cat Par No 289101, Schneider Cat Part No P1001.

S&F Modular Socket outlet, 5 pin, multi purpose 2 module 6 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 /Legrand Cat Part No 673452/ Schneider Cat Part No P2005.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 65 x 50 mm, three terminals, AC 230 volts etc, complete all as specified and directed. Make : Havells Cat Part No Reo/Cona Cat Part No 9246/GM Cat Part No 8224

Taking down ceiling fan of any sweep & size and refix in same position after overhauling including minor repairs by replacement of capacitor, safety pin, cap, nuts & bolts etc and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S &F in repair the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

M&L for Surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

M&L for Surface mounted 1x10 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 12W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed. Notes for Srl Item Nos. 83 to 86 :- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintaince required, if any can be carried out from Top cover.

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole neutral (SPN) 240 volts, 6 to 32 Amps, 10KA (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for sheet metal enclosure MCB distribution board double door single pole neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fxing DB and making good distributed wall surafce to match with existing specification complete all as specified and directed. Make: Legrand Cat Part No 607712 or equivalent model in L&T/Hager/SCHNEIDER

S&F in replacement distribution board iron clad,double door with IP-43 protection suitable for MCCB as incomer and MCB as outgoing 415 Volts 3 phase 50 C/S '4' way, complete with and including approriate size copper busbar and neutral link complete with one MCCB 3 pole 415 Volts 100 Amps rating with rupturing cap 16 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge. [Note :- Outgoing MCBonly shall be measured and paid separetly]

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wiring : Polycab/Anchor/Finolex

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 16 sqmm 4 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

M & L for sand filling in trenches dry and and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed. [Note : Punned thickness shall be measured and paid]

M & L for well burnt bricks , laid flat ( old size) sub class B designation 75 for cable protection complete all as specifed and directed.

S&F for GI tubing 40 mm bore light grade laid in trenches/floors/ fixed to wall/poles for protection of cable with necessary fittings and FI clamps duly painted complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep in hard/dense of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

M/S CANTILEVER ENGINEERS

M/S J N TRADERS

GANDOTRA CONSTRUCTION CO