PROVN OF REVENUE WORKS AND SPECIAL REPAIR TO CERTAIN BLDGS AT PATTAN UNDER GE 969 EWS

Amount

Dismantling of plain or corrugated steel sheeting , any gauge and thickness in roof covering including Nainital or similar pattern roof covering, complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantling 40 sq cm and over in section in any position as in unframed work, complete all as specified and directed.

All as per above Srl No 4 here-in-before but except timber

M&L 2nd Class soft wood as in scantling, clean swan timber framed and fixed, complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) and boarding any thickness, including cover fillets complete all as specified and directed.

M&L for 6 mm thick veneered decorative Ply wood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with nails to timber frame work on ceiling etc.

M&L for 6 mm thick veneered decorative Ply wood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with nails to timber frame work in partition, wall panelling etc.

Dismantling timber scantling in fillets rails, posts purlins etc under 40 Sqcm in section in framed work complete all as specified and as directed.

S&F Second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 13 and not exceeding 25 Sq. cm complete all as specified and directed.

S&F second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with nails, cross sectional area not exceeding 3 Sq. cm complete all as specified and as directed.

2nd class soft wood 20 mm thick in facia/eaves boarding fixed with nails in any situation planed one side with butt joints, complete all as specified and as directed.

S&F 2nd Class softwood weather boarding clean swan, plain 20mm thick or feather edges 15mm to 20 mm thick and fixed with 30mm over laps, complete all as specified & directed.

All as per Srl No 14 here-in-before but except boarding.

Demolition cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L 75 mm thickness Cement concrete type D2, 1:4:8 (40mm graded aggregate) as in flooring, complete all as specified and as directed.

M&L 40 mm thickness Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in flooring complete all as specified and as directed.

M&L for white colour Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry andpointed in white or coloured cement to match over and including cement screed base 15mm screed bed in CM (1:4) and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for coloured Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 Sqm but n.exc 0.11 Sqm. in floors set and jointed over and including cement screed base 15mm screed bed in CM 1:4 and pointed in white or coloured cement to match complete all as specified and as directed.

S&F glazed ceramic coloured tiles 7mm thick 450 x 300mm size in verticle surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick plastering with CM (1:4) complete all as specified and as directed.

M&L for 70mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site complete all as specified and as directed.

S&F 2nd Class Soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

S&F 2nd class 30 mm thick soft wood glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats size of members of shutters as specified in SSR Part - I section 8 Clause 8.23 (b) for windows, ventilators etc are provided with stiles and rails, complete all as specified and as directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (Without taking off shutters from the frames), complete all as specified and as directed.

S&F 35 mm thick 2nd class soft wood glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats, complete all as specified and as directed.

S&F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete all as specified and as directed.

S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge.

S&F Aluminium anodised 100 mm long Butt hinges with galvanised mild steel screws complete all as specified and as directed.

MS Cold rolled Butt hinges medium weight 100 mm long complete all as specified.

MS Cold rolled Butt hinges medium weight 75 mm long complete all as specified.

S&F 300 mm long mild steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minium of 6 bolts and nuts four on bolt plate and two on stapple plate and fixed, complete all as specified and as directed.

S&F 300 mm size mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F mild steel barrel tower bolts, ISI market stove enamelled block with bright bolt and fixed complete all as specified and directed 200 mm long.

S&F Aliminium anodised barrel tower bolts, 150 mm long complete all as specified and as directed.

S&F mild steel pressed handles, oval type ISI marked stove enamelled black complete all as 150mm size specified and as directed.

S&F Aluminium anodised handles, cast type anodised 125 mm long complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.46 mm nominal dia of wire and avarage width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple, complete all as specified and as directed.

Hacking out old broken glass from wooden/metal frame of any thickness incl punching or drilling out old glazing pins/springs clips and providing and fixing new ones complete all as specified and as directed.

M&L sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames, complete all as specified and as directed.

Taking down or up 15mm bore GI tubing including cleaning for refixing or removal to store etc, complete all as specified and as directed.

Taking down or up 20mm bore GI tubing including cleaning for refixing or removal to store etc, complete all as specified and as directed.

S&F 15mm bore medium graded GI tubing with all fittings and fixed complete to wall and ceiling or laid in trenches, complete all as specified and as directed.

S&F 20mm bore medium graded GI tubing with all fittings and fixed complete to wall and ceiling or laid in trenches, complete all as specified and as directed.

S&F Lagging to 15mm internal dia GI pipes used in internal water supply or plumbing all round with, 40mm thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh, complete all as specified and as directed.

All as per above item No. 47 but for 20mm internal dia GI pipes, complete all as specified and as directed.

S&F in repairs 1000 ltrs capacity Rotational moulded polyethylene in white coloured three layered ISI Marked water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as per specified and directed.

S&F Fe-290 (Gde E-165) angle of 65x65x6mm size for compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.

S&F in repairs 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & hihdesity plastec ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms) etc complete all as specified and as directed.

S&F in replacement of 20mm bore gun metal gate valves, with iron wheel head, screwed both ends suitable for iron pipe, complete all as specified and as directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe etc complete all as specified and as directed.

S & F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repair PVC low level cistern of 10 litres capacity inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle and Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete of approved make complete all as specified and as directed.

S&F Vitreous China wash hand basin with pedestal, white, flat back size 550x400mm excluding tap, chain, plug but including brackets and cutting for providing ends of brackets fixed in repair complete all as specified and as directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality, complete all as specified and as directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality, complete all as specified and as directed.

S&F in repair 15 mm bore Angular stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe or for unions and fixed,complete all as specified and as directed.

S&F Central hole basin mixer Brass CP for mixing hot & cold water screwed down for iron pipe and fixed for mixing hot and cold water screwed down for iron pipe and fixed for 15mm dia bore pipe fixed in repair, complete all as specified and as directed.

S&F Wall mixer two-in- one Brass CP for mixing hot & cold water screwed down for iron pipe and fixed for mixing hot and cold water screwed down for iron pipe and for OH shower fixed for 15mm dia bore pipe fixed in repair complete all as specified and as directed.

S&F of Bib tap chromium plated in repair of 15 mm dia bore, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges, complete all as specified and as directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F in repair CP soap tray fixed to walls with rubber plugs complete all as specified and directed.

S&F 125mm dia CP grating doom with/without waste hole (Minimum weight 40 gms) complete all as specified and as directed.

Excavation in trenches in any type of soil, n exc 1.5 M wide and n exc 1.5 M deep for foundation, etc or for shafts, wells, manholes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out soft and loose soil complete all as specified and as directed.

Returning filling in incl spreading leveling, watering and well ramming in layers n exc 25 cm of loose and soft soil complete all as specified and as directed.

Removing excavated materials n exc 50M and depositing where directed at a level n exc 1.5 M above the starting point, complete all as specified and as directed.

Demolition of brick work stone masonary of any type built in cement mortar in foul condition etc complete all as specified and as directed.

M&L Brick work with sub class 'B' burnt bricks (old size bricks) straight on curved on plan exc 6 M mean radius built in CM (1:4) complete all as specified and directed.

M & L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6), complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth complete all as specified and as directed.

M&L for 100mm thick PCC type B-2, 1:2:4 using 40mm graded aggregate and finishing the surface even & smooth without using extra cement, complete all as specified and as directed.

Providing, precast cement concrete type B1 1:2:4 (20 mm graged aggregate) as in manholes cover slab, etc.(of any section indicated), with plain fair faces, including chamfers weatherings, throating etc. and setting in mortar complete with joints to match, complete all as specified and as directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Taking down pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc complete all as specified and as directed.

S&F 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint laid in trenches or in floors etc complete all as specified and as directed.

S&F 75 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls etc complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) Bends with accesss door etc complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) Bends with accesss door etc complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) junction single (Single T) equal of unequal, complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) junction single (Single T) equal of unequal, complete all as specified and as directed.

M&L for 125/110 mm PVC (SWR) trap setting and jointed with solvent cement complete all as specified and as directed.

M&L for 75 mm PVC (SWR) floor trap setting and jointed with solvent cement complete all as specified and as directed.

Demolition and breaking up to 150 mm internal dia of drain pipes (SGSW, AC or Re-inforced concrete) set in cement laid in trenches incl all fittings & accessories, complete all as specified and as directed.

S&F 100mm bore Asbestos cement pipes in any length with cement joints; complete all as specified and as directed.

S&F bends plain for 100mm bore asbestos cement pipes, complete all as specified and as directed.

M&L for concrete bed to drain pipes in PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate including packing under haunching against the sides of pipe after they are laid and tested for 150mm dia.

Cutting in to existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for as specified dia of pipe 150mm.

Cutting in to existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for as specified dia of pipe 100mm.

Preparation of old painted surface of wood and wood based surface any description not otherwise described over 10cm width or girth including knotting and stopping and all preparation work required and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and as directed.

Preparation of New or previously untreated steel and iron based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide primer complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil complete all as specified and as directed.

M&L Plain Cement concrete 1:4:8 type D-2 (40 mm graded aggregate) in foundation, filling and mass concreate, complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, plinth beam columns and stanchions in rough finished surface of concreate at square, complete all as specified and as directed.

M&L for RCC (Norminal Mix) 1:2:4 using 20 mm graded aggregate for Foundation, including rafts, footings, foundation beams, plinth beams, bases for columns ect, basement slabs under reamed piles and mass concrete, complete all as specified and as directed.

M&L for Factory solid Pre-cast cement concrete 1:3:6 type C1 (20 MM graded aggregate) (vibrator made) mechnically pressed block masonry, exc. 10 cm in width and setting in cement mortar (1:6), complete all as specified and as directed.

M&L Rendering 15 mm thick in cement and sand mortar 1:4 on other than fair faces of brick work or cement concreate surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of plastered surface of wall and applying two coats of cement base paint on new surface, complete all as specified and as directed.

M&L for hardcore of gauge not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to true surface complete all as specified and as directed.

M&L Cement concrete 25 mm Thick type B-1, 1:2:4 ( 20 mm graded aggregate finished the surface even and fair without using extra cement, complete all as specified and as directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm,set and jointed in neat cement slurry and pointed in white or coloured cement to match. Incl screed bed 15 mm thick in CM (1:4) complete all as specified and as directed.

S&F for 50 mm thick wall panel made of 0.5 mm thick not dipped galvanized steel sheet on both side with 50 mm thick, layer of rigid etc free closed cell polyurethane foam with tongue and groove joint including cam lock system for interlocking fixed on base channel 30x36x1.25 mm thick density of form shall be 40 kg/cum (+- kg/cum) the panel shall be precoated as approved by GE complete all as specified and as directed.

S&F for 40 mm thick puff insulated panel made of 0.5 mm thick on both side with 40 mm thick rigid polyurethane with tongue and groove joint interlocking for ceiling to be fixed with and both including inverted CRCA Tee secion 50x50x5 mm thick and L section of 50x50x5 mm thick to roof trusses including handing arrangments complete all as specified and as directed.

S&F for sliding type three track alluminium window provided with top and side member 92x317x1.5 mm thick (1.06 kg/Rmminimum weight) bottom three track rail shall be 90x31.75x1.5 mm (1.248 kg/RM) shuttter shall of 40x31.75x1.5 mm section (0.547 kg/RM weight) shutter shall be provided with handle and self locking arrangement interlcking style shall of 40x18x1045 mm(0.607 kg/RM) pannel shall be of 6 mm thick clrae grade 6/2 Rs. 1.3 mm polycarbonate shall the winoe shall be fixed to wall panel as per standrad practice two shutter shall glazed and one shutter shall be wire gauged of aperture 1.40 mm all as specified and directed.

S&F Flush shutters 30 mm with solid core construction, with block board core and plywood face panels, commercial type complete all as specified and as directed.

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade all as specified and directed by Engr-in-charge.

S&F mild steel plates, Fe-410 W (Gde-E250) quality B plain or chequerd, 5 mm thick or over in thickness in available sizes.

S&F of mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, n exc 30cm long, complete all as specified and as directed.

Mild steel TMT bars 6mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

M&L for providing 75 mm thick plain Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in plinth protection complete all as specified and as directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

Aluminium handles, cast type, anodised (150 mm) complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed (200 mm) complete all as specified and as directed.

M&L for Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil, complete all as specified and as directed.

M&L Hard core of broken stone or boulder of gauge exceeding 63mm but not exc 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L 100mm thick Cement concrete type D-2 1:4:8 (40mm graded aggregate) mass concrete as in sub base, complete all as specified and as directed.

M&L Chequered cement concrete tiles (vibrator made) 30cm x 30cm x 25 mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment over 15mm thick screed bed in CM (1:4) finished with coloured cement to match the shade of the slab.

M&L for Providing, cement concrete type B-0 using (12.5 mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and as directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and as directed.

Complete removal of existing treatement preparing plastered surface or unplastered surface by Washing, rubbing down and stopping of distempered and painted surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and as directed.

Supply, install and commissioning of kero based water heating plant of capacity 500 Liters alongwith complete connected/requirement accessories for operating kero based water heating plant with full effieciency complete all as specified and directed. (Note: quoted rate is inclusive cost of foundation)

M&L for lagging on 20mm internal dia pipe all round with 25mm thick bonded mineral wool pre-formed 'SNAP ON' pipe section of density of 144 Kg/Sqcm confirm to IS 9842 including providing with chicken mesh wire netting 25 gauge 29mm mesh etc, complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 in foundations, filling and mass concrete, complete all as specified and as directed.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles as necessary gusset plates, riveting etc confroming, to Fe-290 Gde E-165 complete all as specified and as directed.

S&F 6mm thick Plates (Plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming with riveted, bolted or welded attachment confirming to Fe-290 (Gde E-165) etc complete all as specified and as directed.

Taking down carefully copper/aluminum point wiring (light. Fan, socket or power) complete, incl fittings such as switches, ceiling roses, pendants, regulators, sockets etc, removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors etc

M&L for point wiring in PVC casing caping with 1.5 Sqmm size multi stranded FRLS copper conductor cable 1.5 Sqm including clamps, screws guttier/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable of size 1.5 Sqmm as earth continuity conductor.

(a) One light point/fan point/Ex fan point controlled by one 5 Amps switch one way

(b) One 3 pin 5 Amp switch socket outlet on independent board

(c) One 3 pin 5 Amp switch socket outlet on same board with accessories

M&L for point wiring in PVC casing caping with 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps, screws guttier/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated fire retardant cable of size 2.5 Sqmm as earth continuity conductor.

S&F switch piano Flush type, single pole, one way 6 amp 240 volts, complete all as specified and as directed.

S&F switch piano Flush type, single pole, 15/16 amp 240 volts, complete all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 Amps, flush type complete with gang box, all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 Amps, flush type complete with gang box, all as specified and as directed.

S&F ceiling rose 3 terminal / PVC/ Polycarbonate, isolated body, complete all as specified and as directed.

S&F in repairs Distribution Board, SPN 8 Way, Double door complete all as specified and as directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200 mm sweep. BEE 5 Star with brushless direct current motor.

S&F in repairs MCB,DP 40 Amps 240 Volts B curve, complete all as specified and as directed.

S&F in repairs MCB, SP 6-32 Amps 240 Volts B curve, complete all as specified and as directed.

S&F LED fitting 1x20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified and as directed.

S&F LED light fitting 1x10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED Bulb 12W, 220 V suitable size from lamp holder, complete all as specified and as directed.

S&F LED Bulb 15W, complete all as specified and as directed.

S&F lamp Holder, PVC/Polycarbonate type with black plate suitable for batten fitting complete all as specified and as directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm complete all as specified and as directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified an as directed.

S&F in repair capacitor 1.5/2 mfd suitable for 1200mm sweep ceiling fan complete all as specified and as directed.

M&L sub main wiring with two run single core 6 Sqmm FRLS copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia PVC conduit/casing caping, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall along with one run of 6 Sqmm single core PVC FRLS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion etc complete all as directed. Note: Two runs of 6 Sqmm and one run of 6 Sqmm cable and one run of casing capping shall be measured as one RM

Taking down & dismantling the ceiling fan from site and removing its allied smaller parts for cleaning, servicing, oiling and lubricating and replacement of unserviceable parts such as bearings, bushes, etc and refixing the same fan in its original position with all the parts i.e. down rod, canopies, fan blades, split pins, screws, nuts and spring washers complete including, flexible chord of 24/ 0.20mm with neccessary connector (for blade/ body) as required after rewinding complete all as specified and as directed. Note : Spares used and rewinding shall be measured and paid separately under relevant item.

M&L in repairs for Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia(up to 7.5 m in length from earth plate) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and as directed by Engineer in charge and tested on completion. Note : The rate is inclusive of necessary earth work, RFR and removal etc

Supply and laying XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size 25 Sqmm 2 core laid in trenches or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing, complete all as per specified and as directed.

M&L for sheet metal enclosure for DBs when MCB to be used single phase 240 Volts, double door 04 Way with 200 Amps rated bus bar complete all as specified and as directed.

S&F 1100 V grade heavy duty cable with pvc insulated aluminium conductor served with an inner sheathing of pvc tape and overall pvc sheathed in service connection suspended by insulating hangers not more than 1mtr apart including 4mm suspension wire one twin core cable flat or circular of size 16 sqmm all as specified and as directed.

S&F voltage stabilizer copper wound of capacity 4 KVA working range 150v - 270v , complete all as specified and as directed.

Supply and spreading clean dry sand in trenches for cushioning all as specified for cable protection complete all as directeed. (Note: The punned down thickness shall only be measured)

Supply and laying sub class 'B' bricks laid across the cable for cable protection complete all as specified and as directed.

S&F Gl Tubing light grade 40mm dia with all fitting laid in trenches, complet all as specified and as directed.

Note:- Schedule of credit Rs 35,987.00 will be deducted from total amount quoted while accepting the bid. Details of schedule of credit is given in tender documents.

M/S JAVID AND CO (BID ID -3116776)

M/S BHAT AND CO (BID ID -3117111)

M/S IQ ENTERPRISES (BID ID -3115961)

M/S SUMJI BROTHERS (BID ID -3115184)

M/S NISAR AND CO (BID ID -3116658)

ALI MOHD NAJAR (BID ID -3115158)

M/S GHULAM QADIR WANI AND SONS (BID ID -3116515)

M/S ESS EMM ENTERPRISES (BID ID -3116274)