Construction of Rajsav Sadan at Reckong Peo in Distt. Kinnaur HP (SH-Building portion, W.S. and S.I., Site Development, Septic Tank and Rain water harvesting system thereof)

Amount

Cutting in earth work in all heights and depths and in all kinds of soils including saturated soil comprising of Pick, Jumper , blasting work both in soft and hard rock with chiseling, wedging-out of rock where blasting is prohibited, their intermediate classification of soil, setting-out true to the required lines, grades, side slopes, trimming bottoms to levels as shown on the drawing and as directed by the Engineer-in-charge at site according to HP.PWD, specification of 1990 Vol-I and sorting-out useful/ un –useful materials and stacking the same in all leads and lifts in acquired width of the road and transportation of useful/ un-useful materials for filling in road ways camber, embankments for grades, improvement and leveling to required grade and disposing of all surplus excavated earth in acquired width of the road or on approved dumping sites (To be arranged by the contractor i/c prescribed dumping charges of M.C / Local body if levied any) through all modes of transportion including head load or animal transport or mechanically means alongwith its leveling, fine dressing and all labour, machineries, tools, equipments and safety measures and other incidental, necessary to complete the work by mechanised means and labour if required. All useful materials such as stones , shingles, aggregates and slates shall be sorted- out and stacked along road side, the quantity of which shall not be less then 280.35 Cum., failing which recovery @ Rupees 300/cum. (Three hundred per cubic metre) shall be effected from the bill of the contractor. Any loss of the public/ private property during the course of execution shall be absolute responsibility of the contractor which shall to be duly compensated by him in all respect, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out , construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto all lead dressing of sides and bottom and backfilling in trenches with excavated suitable material upto all depth, including carriage of material within all leads and lifts.

Excavation in drain and channel in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer-in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor i/c prescribed dumping charges of M.C / Local body if levied any) as per satisfaction of Engineer-in-charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per the direction of Engineer-in-charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer-in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor i/c prescribed dumping charges of M.C / Local body if levied any) as per satisfaction of Engineer-in-charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per the direction of Engineer-in-charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges

Providing form work with steel plates 3.15mm. (Three point fifteen milimetre) thick welded with angle iron in frame 30X30mmx5mm.(Thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden/ steel battens and ballies, height of propping and centring below supporting floor to ceiling any floor/height and removal of the same for in situ-reinforced concrete and plain concrete work, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Foundation, footings bases of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto any thickness in Super-structure for all floor level in all heights.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like.

Columns, pillars, posts and struts. Square, rectangular or polygonal in plan, in Super-structure for all floor level in all heights.

Stair cases with sloping or stepped soffits excluding landings in Super-structure for all floor level in all heights.

Beams, cantilevers, girders and lintels sides and soffits of beams, beam hunchings, cantilevers, bressumers and lintels up to any depth in Super-structure for all floor level in all heights.

Edges of slabs and breaks in floors and walls up to any width in Super-structure for all floor level in all heights.

Providing and laying cement concrete 1:6:12 (One cement : six sand : twelve graded/crushed stone aggregate 40 mm (Forty millimeter) nominal size) mechanically mix by concrete mixer including curing complete excluding cost of centering and shuttering in Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specifications clause 802,803 1202 and 1203. 1:6:12 (One cement : six sand : twelve graged stone aggregate 40mm (Forty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and laying cement concrete 1:4:8 (One cement : four sand : eight graded stone aggregate 25 mm (Twentyfive millimeter) nominal size) and curing complete including cost of form work in foundation of Breast and Retaining wall etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete work 1:2:4 (One cement : two sand : four graded stone aggregate 20 mm (Twenty millimeter) nominal size) mechanically mixed and vibrated for compacting concrete and curing complete to give smooth and even surface including centering and shuttering etc but excluding cost of reinforced work including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Mouldings as in cornics window sills etc. in all thickness and girth

Providing and laying cement concrete work 1:2:4 (One cement : two sand : four graded stone aggregate 20 mm (Twenty millimeter) nominal size) mechanically mixed and vibrated for compacting concrete and curing complete to give smooth and even surface including centering and shuttering etc but excluding cost of reinforced work in Suspended Floor roofs, landing and shelves and their support balconies,beams, girders, bressumers and contilever upto floor twolevel including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge

Providing and laying reinforced cement concrete 1:1.5:3 (One cement : one point five sand : three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mix by concrete mixer and compacting the concrete with vibrator and curing complete excluding cost of form work and reinforcement for R.C.C. work, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Foundation footings complete in all respect

Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers in Super-structure for all floors in all heights.

Column, pillars, posts and struts in Super-structure for all floors in all heights.

Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing in Super-structure for all floors in all heights.

Lintel beam girder bressumers and cantilever upto first level complete in all respect

Providing Tor steel reinforcement including cost of binding wire for R.C.C. work including cutting, bending, binding and placing in position complete in Super-structure for all floor level in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve crushed stone aggregate 20mm (Twenty millimeter) nominal size) at plinth level in Cement Mortar 1:6 (One cement: six sand) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Square rubble masonary coursed with hard stone of approved quality in foundation and plinth in walls including rakingout joints in Cement Mortar 1:3(One cement :three sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204. Random rubble masonry in cement mortar 1:6 (One cement: Six sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Brick work using common burnt clay building bricks in super structure for all floors in all heights using second class bricks in cement mortar 1:6 (One cement isto six sand) and curing complete including carriage of material through all modes of transporation within all leads and lifts and as per PWD specification and entire satisfaction and direction of Engineer-in-charge

Half Brick masonry in common burnt clay building bricks in Cement Mortar 1:4 (One cement: four sand) in Super-structure for all floors in all heights including curing complete :- Second class brick, as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying 20mm (Twenty millimeter) thick marble work Table rubbed and polished in flooring/ work top/ lining over 20mm (Twenty millimeter) thick base in cement mortar 1:3 (One cement : three sand) including jointing with Cement mortar 1:2 with an admixture of pigment to match the shade complete, including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

White makrana marble

Baroda green marble

Stone filling under floor dry hand packed with hard stone of approved quality consolidated properly with hand or mechanical rammer or by hand durmoot to required level as per HPPWD specification 1990 (One thousand Nine hundred Ninety) volume-I including carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing woodwork in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position. 2nd class Deodar wood in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing pannelled and glazed door shutter( in first class Deodar wood having Top rail 10x4 cm (Ten into four centimetre) middle rail 15x4 cm (Fifteen into four centimetre) and bottom rail 20x4 (Twenty into four centimetre) cm sash bar 4x4 cm (Four into four centimetre) and panel 12 mm (Twelve ) thick Phenol bonded (both side) prelaminated Bwp grade partical board in matt finish ISI marked IS.No. 12823 as per approved shade of Kavista or its equvalent below middle rail and above middle rail 5 mm (Five millimeter) thick glass)i/c black enammelled iron butt hinges with necessary screws etc comp. 40 mm (Forty millimetre) thick as per Arch. drg. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56mm (Zero point fifty six millimeter) for doors, windows and clerestory windows including first class deodar wood ornamental beading 20 mm × 12.5 mm (Twenty millimeter into twelve point five millimeter) section including bright finished black enamelled iron butt hinges with necessary screws 40 mm (Forty millimetre) thick 1st class deodar wood as per Arch. drg. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing 12 mm (Twelve millimeter) thick prelaminated board both side BWP phenol bounded shutter with frame of 1st class deodar wood I/C bright finished / black enamelled iron butt hinges with screws. 40 mm (Forty millimeter) thick frame including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge .

Providing and fixing 19mm (Ninteen milimetre) thick commercial board water proof (ISI mark) shutter for cup boards including fixing with nickle plated piano hinges with screws etc. complete as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 1 mm (One milimetre) thick coloured or plain lamination sheet (ISI mark) (sunmica) on boards/ply wood sheets with approved adhesive and nails etc. complete as per HPPWD specification 1990 (One thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing square edges cover fillets (beading) 19mmx6mm (Ninteen milimetre into six milimetre) section i/c mitring at junctions with wood screws and nails complete as per HPPWD specification 1990 (One thousand Nine hundred Ninety ) volume-I , including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 8 mm(Eight milimetre) thick water proof ply in walls fixed with nails and screws completeincluding carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Rai wood panalling with plank size 75X25mm ( Seventy five into twenty five millimetre) and 75X12.5 mm (Seventy five into tweleve point five millimetre) in combination over frame of wood work (to be paid sparately ) with top moulding complete in all respect through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 75 mm x 60mm (Seventy five millimetre into sixty millimetre) rounded hand rails in straight length complete in. 2nd class kail wood. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing brass curtain rail with rollers stop ends and brackets in pelmets instead of wooden curtain rod 25 mm dia (Twenty five mllimetre diametre) and brackets of first class deodar wood (actuallenght) of rails of be measured. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws.Plain grill. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing 40x3 mm(Forty into three millimetre) flat iron hold fast 40 cm(forty cetimetre) long including fixing to frame with 10 mm (Ten millimetre) dia bolts, nuts and wooden plugs and embeding in cement concrete block 30 x 10 x15 cm (Thirty into ten into fifteen centimetre) in 1:3:6 (one cement :three sand :six graded stone aggregate 20 mm(Twenty millimetre) nominal size ). including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing Aluminium sliding door bolt with bolts and nuts screws etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

300x16mm (Three hundred into sixteen millimeter)

250 x 16 mm (Two hundred fifty into sixteen millimeter)

Providing and fixing Aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

300 x 10 mm (Three hundred fifty into ten millimeter)

250 x 10 mm (Two hundred fifty into ten millimeter)

150 x 10mm (One hundred fifty into ten millimeter)

Providing and fixing Aluminium.handles with necessary screws etc., including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

125 mm (One hundred twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (Seventy five millimeter)

Providing and fixing bright finished brass handles with screws etc. complete. 75 mm (Seventy five millimetre) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing bright finished brass ball catcher 10 mm dia (Ten millimetre diametre) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws.150mm (One hundred fifty millimetre) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing powder coated aluminium hooks and eyes 150mm (One hundred fifty millimeter) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing hydraulic door closer with necessary screw etc complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Double Glass panel with rubber gasket to fill the air gaps in windows complete in all respect through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying White glazed tiles 6 mm ( six millimetre) thick in skirting risers of steps and dado of approved make and size 30x45 cm (size thirty centimetre into forty five centimeter) over base of 12mm thick cement mortar 1:3 (one cement : three sand) and jointing with neat cement slurry complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing Garsa stone stone 12mm ( Twelve millimetre) thick Cladding on R..C.C surface side as on faces of Arch masonry walls etc.over base of 12mm (Tweleve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointing with neat cement slurry complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying red mandana sand stone slab flooring 40 mm (Forty millimeter) average thick on 20 mm (Twenty millimeter) average thick base of cement mortar 1:4 (One cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab i/c rubbing and granite polish finish complete. including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying Duro stone vetrified tiles (300mmx300mmx10mm) (Three hundred millimetre into three hundred millimetre into ten millimetre) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm (Tweleve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.t complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying Duro stone vetrified tiles (300mmx300mmx8mm) (Three hundred millimetre into three hundred millimetre into eight millimetre in grey/coloured or of approved shade in skirting risers of steps , dedo on 12mm (Tweleve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.t complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying spartic ceremic tiles 5.5mm. (Five point five millimeter) thick in flooring (300 x 300mm. size) (Three hundred into three hundred millimeter) treads of steps laid on a bed of 12mm. (Twelve millimeter) thick cement mortar 1:3 (One cement: three sand) finished with flush pointing in white cement 1st quality ceramic tiles matt finish Somany/ Orient or its equivalent, as per the direction of Engineer-in-charge including carriage of materials with in all leads and lifts.

Providing and laying heavy dutyprecast cement conrete inter locking paver blocks vibro compacted upto M- 50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm (Twenty five millimetre) thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Cement concrete pavement (25 mm to 50 mm thick) (Twenty five millimetre to fifty millimetre) with 1:2:4 (1 cement :2 sand :4 stone aggregate 20 mm (Twenty millimetre) nominal size) including finishing with a floating coat of neat cement complete. including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying 40mm (Forty millimeter) cement concrete flooring 1:2:4 (One cement: two sand: four graded stone aggregate 20mm (Twenty milimetre) nominal size) laid in one layer finished with a floating coat of neat cement as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing HDF Decoretive laminate core board german kerono flooring AC4 class 8 mm thick (Eight millimetre) placed over cushion of 2 mm (Two millimetre) thick cxpanded polythene foam plus 100 (One hundred) micron thick polythene sheet under lay no 045 beech west including boder including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 0.60 mm (Zero point sixty millimeter) thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm (Six millimeter) diametre with prepainted limpet and rubber washers complete with all accessories, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing ridges or hips 60cm (Sixty centimeter) over all with 0.60 mm (Zero point sixty millimeter) thick prepainted steel sheets of TATA DURASHINE in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating+ back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia (Six millimeter diameter) & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing valley 60 cm (Sixty centimeter) over all 0.60 mm (Zero point sixty millimeter) thick prepainted steel sheet of TATA DURASHINE in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia (Six millimeter diameter) with prepainted G.I. limpet and bitumen whashers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing on wall faces PVC (D Plast) accessoreis for rain water pipes of working pressure not less than 4.5kg/ sqm (Four point five kilogram per squarevmetre) including filling the joints with approved adhesive complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing M.S. BP Sheet 1.66mm (One point sixty six millimeter to 2mm (Two millimeter) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separately)as per the direction of Engineer-in-charge including carriage of materials with in all leads and lifts.

Providing and fixing 6 mm ( Six millimetre) thick cement board celing of everest or its equivalent with standard GI section (GI section paid to be seprately) complete in all respect through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing steel work of TATA,SAIL or RASHTRIYA ISPAT welded in built up section/ hollow section trusses & framed work, including cutting,hoisting & fixing in position including applying a priming coat of red lead paint in grating,framed guards,bars ladders,railing brackets and similar works joists channels, angles, tee, flats / hollow section and the like and as per HP. PWD. Specifications of 1990 vplume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

In trusses and trussed purlins in buildings.

In gratings framed guard bars, laddres, railing, brackets and similar works.

Providing and fixing moulded hand rail of mild-steel hollow pipe 100mm (hundrad millimeter) diameter welded in straight length over mild steel flat at top of vertical balusters including one coat of red oxide priming coat complete (Mild steel flat & balusters of railing shall be measured and paid separately) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 15 cm. (Fifteen centimetre) wide 45 cm. (Forty five centimetre) overall semicircular plain G.I. sheetgutter with iron brackets 40x3mm (Forty into three millimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design. 0.80mm (Zero point eighty millimetre) thick sheet. through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand as per complete.With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chromen including carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Painting two costs (excluding priming cost on new steel and other metal surfaces under coat with ready mixed paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters with Enamel paint other than white/ white, including carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Applying white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand pepered smooth to give final matter finish to the surface complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

6mm (Six millimeter) Cement Plaster to ceiling. In cement mortar 1:3 (One cement : three sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster in single coat on fair side of brick/concrete walls for internal / exterior plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80 mm (Eighty millimeter) in girth and finished even and smooth with Cement mortar 1:6 (One cement : six sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster in single coat on the rough side of brick/concrete walls for internal plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80 mm (Eighty millimeter) in girth and finished even and smooth. Cement mortar 1:6 (One cement : six sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

20mm (Twenty millimetre) Cement plaster in two coats,backing coat 15mm (Fifteen millimetre) and finishing coat 5mm (Five millimetre) thick on rough side of brick/stone masonry walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth.including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Distempering (Two coats) with Ist quality oil bound washable distemper of Asian paints or equivlant of approved shade and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on under coated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface. including sand paper smooth complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing plinth protection 50 mm (Fifty millimetre) thick in cement concrete 1:3:6 (One cement isto three sand isto six graded crushed stone aggregate 20mm (Twenty millimetre) nominal size including finishing the top surfaces of concrete smooth as per HP. PWD. Specifications of 1990 Volume-I, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing under layer for plinth protection of 75 mm (Seventy five millimeter) thick (unconsolidated) bed dry brick/stone aggregated 40 mm (Forty millimeter) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing weep holes in brick masonry /stone masonry/plain reinforced concrete abutments, wing wall, return wall,with 100mm (One hundred millimeter) dia PVC pipe extending through the full width of the structures with slope of 1(v):20(H) (One vertical : twenty horizontal) towards drawing face complete as per drawing and technical specification clauses 614,709,1204.3.7 (For R/wall) , including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 1204.3.8. Granular material ,including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying of boulder apron laid in wire crates with 4mm dia (Four millimetre diametre) GI wire conforming to IS;280 and IS;4826 in 100mm x 100mm (One hundred millimetre into one hundred millimetre) mesh(woven diagonally) including 10 (Ten) per cent extra for laps and joints laid with stone boulders weighing not less than 25 Kg. (Tenty five Kilogram) each as per drawing and technical specifications Clause 1301, including carriage of material within all leads and lifts.

Providing and laying in trenches galvanised mild steel tubes (medium grade), tube fittings (earh work in trenches to be measured and paid separately) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

20 mm (Twenty millimeter) nominal bore

Constructing chamber 300x300x500mm (Three hundred into three hundred into five hundred millimeter) inside size for stop cock with C.I surface box 100mm x 100mm x 75mm (One hundred millimeter into one hundred millimeter into seventy five millimeter) with hinged cover fixed in cement concrete slab 1:2:4 graded stone aggregate 20mm (Twenty millimeter) nominal size) 75 mm (Seventy five millimeter) thick foundation concrete 1:5:10 and inside palstering with cement mortar 1:3 finished with a floating coat of neat cement incluiding curing complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Constructing chamber 600mm x 600mmx750mm (six hundred millimeter into six hundred millimeter into seven hundred fifty millimeter) inside size for fire hydrants with C.I. surface box 350mmx 550mm (Three hundred fifty millimeter into five hundred fifty millimeter) top and 165 mm (one hundred sixty five millimeter) deep (inside) with changed lid and RCC top slab 1:2:4 mix (one cement : two sand four graded stone aggregate 20mm (twenty millimeter) nominal size) 100mm (one hundred millimeter) thick foundation concrete 1:5:10 ( one cement : five sand : ten grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (one cement :three sand) finished with a floating coat of neat cement including curing complete With 150 mm (one hundred fifty millimeter) thick walls of reinforced cast in situ plain cement concrete walls in 1:2:4 mix (one cement: two sand : four grades stone aggregate 20 mm (twenty millimeter) nominal size complete with form work and reinforcement with 6mm (six millimeter) bars not exceeding 150 mm (one hundred fifty millimeter) centres both ways , including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(One cement : one sand) (Seat and over to be measured and paid for separately) as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Anglo Indian Universal closet of Hindware Cat No. 20012 of white shade

Providing and fixing 100 mm (One hundred millimetre) size 'P' or 'S' trap for water closet ( squatting pan)including jointing the trap with the pan and soil pipe in cement mortar 1:1(1 cement : 1 sand)Vitreous China as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers HOLLOW TYPE:Black or white plastic seat and cover as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing vitreous china wash basin No. 10001 with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings:- Flat back 630mm x 450 mm (Six hundred thirty millimeter into four hundred fifty millimeter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing viterious china pedestal for wash basin complete recessed at the back for the reception of pipes and fittings, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing rubber plug for sink/ wash basin 32mm dia (Thirty Two millimeter diameter)including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing M.I. Union for wash basin or sink 32 mm dia (Thirty two millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass S. Trap for wash basin and sink 32 mm dia (Thirty two millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 100mm (One hundred millimeter) sand cast iron grating for gully, floor or Nahni trap, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 600 mm x 450 mm (Six hundred millimeter into four hundred fifty millimeter) bevelled edge mirror of superior glass mounted on 6 mm (Six millimeter) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws and washers. 750 mm x 20 mm (Seven hundred fifty millimeter into twenty millimeter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 600x120mm (Six hundred into one hundred twenty millimeter) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. brass screws, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P.Brass Toilet peper holder, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass bib tap (heavy duty ISI marked IS:8931 & 8934) of Jaquar with capastan head. 15 mm dia (Fifteen millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass pillar tap of Jaquar with Capstan head (heavy duty ISI marked IS:8931 & 8934) 15 mm dia (Fifteen millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Brass stop cocks of Jaquar 15 mm dia (Fifteen millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P.brass angle valve of Jaquar (heavy duty ISI marked IS:8931 & 8934) 15 mm (Fifteen millimeter) without Nuts and pipe, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing P.V.C. connection with brass unions:- 300/450 mm (Three hundred/four hundred fifty millimeter) length (heavy duty ISI marked IS:8931 & 8934) 15 mm (Fifteen millimeter) nominal bore, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixig brass full way valve with wheel 20mm (Twenty millimeter) nominal bore, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Polytheline-Aluminium-Polythelene(PE-AL-PE) composite pressure pipe U.V. stabilized with carbon black conforming to IS-15450-2004 water supply including clamp at one metre spacing, cutting,fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall. Internal work-Exposed on wall, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

1620 (20 mm (Twenty millimeter) O.D. pipe)

1216 (16 mm (Sixteen millimeter) O.D.Pipe)

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (Fifteen millimeter) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 2000 litres (Two thousand litres) net capacity tank, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete 110 mm x 75 mm (One hundred ten millimeter into seventy five millimeter), including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

75 mm dia (Seventy five millimeter diameter)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (Three millimeter) thick bolts and nuts complete including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

75 mm dia (Seventy five millimeter diameter)

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (Three millimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

75 mm dia (Seventy five millimeter diameter)

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

75 mm dia (Seventy five millimeter diameter)

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

75 mm dia (Seventy five millimeter diameter)

Providing and fixing P.V.C. Reducer ISI marked including jointing with approved adhesive etc. complete., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150mm × 110mm (One hundred fifty millimeter into one hundred ten millimeter) diameter.

110mm × 75mm (One hundred ten millimeter into seventy five millimeter) diameter.

Providing and fixing 10.00 ltr. (Ten liter) capacity PVC low level duel flushing cistern CERA catalogue No. 2603 or equivalent with a pair of brackets with fittings such as lead valve, less syphon, 15mm (Fifteen millimeter) nominal size PVC ball valve with polythene float, PVC handle, union and coupling for connection with inlet, outlet and overflow pipes 40mm (Forty millimeter) diameter PVC flush bend with cistern and closet & over flow pipe to be paid for separately, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT ball valve of approved quality and colour 15mm (Fifteen millimeter) nominal bore, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing PTMT jet spray of approved quality and colour with one meter tube, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Bottle Trap for wash basin and sink 32 mm dia (Thirty two millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Constructing manhole with R.C.C. top slab in 1:2:4 mix (One cement: two sand : four graded stone aggregate 20 mm (Twenty millimeter) nominal size), foundation concrete 1:4:8 (One cement : four sand : eight graded stone aggregate 40 mm (Forty millimeter) nominal size), inside plastering 15mm (Fifteen millimeter) thick with cement mortar 1 : 3 ( One cement : three sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 mix (One cement : two sand : four graded stone aggregate 20mm (Twenty millimeter) nominal size) finished smooth complete including curing and testing including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Inside size 800 mm x 800 mm and 500 mm deep including precast RCC cover with frame (Heavy duty single seal Pattern-1) 455 mm x 610 mm (Four hundred fifty five millimeter into six hundred ten millimeter) internal dimensions. With 230 mm (Two hundred thirty millimeter) thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (One cement : three sand)

Providing and fixing CI underground type fir hydrant confirming to IS 909, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Box (Surface) for fire hydrant waight 30/31 Kg (Thirty / Thrity one kilogram) , including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying ( to level for sope) and jointing reinforced concrete light duty non pressure pipe in 1st class NP-2 of following internal diameters with collars and butt ends prepared for coller joints including testing of joints in 300 mm diameter (Three hundred millimeter diameter) , , including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

BASANT KASHYAP