REPAIR TO JOINERY, ROOF TREATMENT, FLOORING, PLUMBING AND CERTAIN MISC B/R WORK IN E/M INSTALLATION UNDER GE (W) MATHURA

Amount

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down shutter only of any description exc 1 sqm but n. exc 2 sqm each complete all as specified and directed.

S&F Pressed steel frame made out of MS Sheet 1.25mm thick for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified and directed. Note:- During fixing of chowkhat, surface shall be make good in plumb with existing finishies like cement plaster simlar wall tiles, floor tiles etc as per site requirement.

S&F Pressed steel frame made out of MS Sheet 1.25mm thick for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified and directed. Note:- During fixing of chowkhat, surface shall be make good in plumb with existing finishies like cement plaster simlar wall tiles, floor tiles etc as per site requirement.

M&L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified and directed.

S&F 35mm thick plain framed panelled door shutter, factory made (any number of panels) of 2nd class hard wood with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces including 2nd class hard wood kail beading 20mm wide tapering from 10mm to 5 mm on one side of shutter & fitted to chowkhats. The size of rail and style shall be as per IS –1003 (Part-I) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and directed.

S&F 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR pt-1 section 8.24 (a) complete all as specified and directed.

S&F Factory made PVC single door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as per specification and drawing of SSR Part-I and the door frame to be fixed to the wall using MS screw 75mm long with PVC fastener as per manufacturer's, instruction complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with particle board core and 2,4 or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front Face & 2mm Plain colour PVC sheet on back face, fixing in frame at site complete specification & drawing as per SSR complete all as specified and directed.

M&L for preparing new wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed.

S&F 150mm stainless steel barrel tower bolts with bright bolt and fixed complete all as specified and directed.

S&F 150mm long stainless steel handles, oval type complete all as specified and directed.

S&F 300mm stainless steel sliding door bolts, bolt type with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F factory made steel ventilator with top hung shutter including hinges , steel peg stay complete all as specified and directed.

S&F framed work such as grill gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters walk ways railing frame work of ceiling etc and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamels paints over a coat of red oxide primer complete all as specified & directed.

S&F MS Angle, flat iron ,round bars such as in door frame, ladders work to fix in PCC grouting, welding etc confirming to Fe-290 Gde E-165 complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 sq.m. in each pane complete all as specified and directed.

Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size straight or curved on plan exc 6mtr mean radius, built in CM (1:6) complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM in (1:4) finished fair and even external surface complete all as specified and directed. Note : this item will be executed in G+2 floor bldg.

M&L for rendering 15 mm thick in CM (1:6) on brick or concrete surface on other than fair faces of brick complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L preparation of new plastered surfaces and applying two coats of OBD over one coat of primer on walls complete all as specified and directed.

M&L for rendering dubbing coat over irregular surfaces of chajjas roof projections/ceiling/facia etc average 15mm thick in CM (1:4) over cement slurry coat @ 3Kg/Sqm making the surface even followed by 5mm thick rendering in CM (1:3) furnished even & smooth including making of drip course as required complete including roughening surface of old concrete by picking sweeping clean and washing with water complete all as specified and directed. Note : Rate for form work if required shall be deemed included in the unit rate quoted by the contrator.

Taking up or down steel tubing 15mm bore pipe complete all as specified and directed.

Taking up or down steel tubing 20mm bore pipe complete all as specified and directed.

M&L GI tubes medium grade, with all fittings and fixed complete to wall and ceiling/floor 15mm bore complete all as specified and directed.

M&L GI tubes medium grade, with all fittings and fixed complete to wall and ceiling/floor 20mm bore complete all as specified and directed.

Dismantiling floor, hearth or wall tiling including cement motar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premishes complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortor (1:6) for laying floor finishes. complete all as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surface 450x300x7 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match fixed over and including 15mm thick rendering on brick work/concrete surfaces in cement mortar (1:4) for skirting /dado finishes complete all as specified and as directed.

M&L Non skid coloured ceramic tiles 8 to 9 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortor (1:6) for laying floor finishes. complete all as specified and as directed.

Dismantling of ceiling boards of any type and any thickness including cover fillets and timber frame work complete all as specified and directed.

S&F 605X605 mm size of grid GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length ) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the internediate channel with connecting clips across the intermediate channel at 457mm centre to centre including providing and fixing 4mm thick everest designer ceiling board at size 600x600mm non combustible material as per AS-1530 Part-3 of IS-14802 with fixing arrangment complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floors and paving not exc 15cm thick below or above ground level complete all as specified and directed.

M&L for 100mm thick plain cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for sand filling under floors or in foundation complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block with grey cement & pigment any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

M&L for pre-polished chequered tiles (any colour) of size 30cm x 30cm x 25mm thick, with gray cement & pigment set, jointed and pointed in neat cement slurry in floors laid over and including 20mm screed bedding in cement mortar (1:4) complete all as specified and directed.

M&L for 100 mm thick plain cement concrete type B-1, (1:2:4) using 20 mm graded stone aggregate as in floor or floor finishes complete all as specified and directed.

M&L for Providing, cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in coping, coving, roof padding, roof kerb on roof chamfered on edge complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with pigment to match the shade of the slab including rubbing and polishing including screed bed and bedding layer of mortar 20 mm thick in CM (1:3) for laying floor finishes size complete all as specified and directed.

M&L for grinding, cutting and polishing to old surface of kota stone as in floor, skirting, dado, steps in three grinding with marble stone and cleaning of floor and disposal of rubbish outside complete all as specified and directed.

M&L for preparation of old plaster surfaces of walls and applying one coat of cement based paint on walls complete all as specified and directed.

M&L for preparation of old painted surface of any discpription and applying one coat of weather coat paint of Dark Shade, complete all as specified and directed.

M&L for preparation of old distempered surfaces of walls and applying one coat of distemper oil emulsion white or tinted, complete all as specified and directed by Engr-in-Charge

M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old steel surfaces of any description or girth over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion from natural ground and making good disturbed ground complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 m and making good surface in soft/loose soil complete all as specified and directed.

S&F mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long and diameter of neck in mm 5 to 10 complete all as specified and directed.

M&L for PCC (1:3:6) type B-1 using 20mm graded stone aggregate as in bed plates of vertical steel posts etc and similar works including necessary form work complete all as specified and directed.

Dismantling chain link fencing of any guage & size not exc 4 Kg/Sqm complete all as specified and as directed

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

S&F mild steel flat iron as in hold fasts, wind ties etc and similar small work confirming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for Mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Dismantling brick/concrete tiles any size complete all as specified and directed.

Demolition mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) including removing the demolished material to a distance exc 250m but n. exc 500m and deposited where directed at a level n.exe 1.5m above starting point complete all as specified and directed.

M&L for Providing, cement concrete (1:2:4) type B0 using 12.5mm graded stone aggregate as in roof padding complete all as specified and directed.

S&F precast hydraulically pressed PCC tiles of size 25cm x 25cm x 20mm thick laid over and including screed bed 15mm thick in CM (1:4) set and jointed in neat cement slurry and pointed in CM (1:3) mixed with WPC of approved make in screed bed and pointing on roof complete all as specified and directed.

M&L for water proofing treatment with APP modified bituminous membrane 3mm thick consisting of the following for RCC roof :- (a) Cleaning palstered roof surfaces and applying a coat of oxidised bitumen based solvented primer a@ 0.3Kg /Sqm of approved make on top of dry surface of RCC roof complete all as specified and directed. (b) M&L for APP modified polymeric water proofing membrance 3mm thick weight not less than 3.0 Kg/Sqm with non woven polyster core of approved make applied by heating one surface of membrane with LPG torch with lap of 100mm and the overlap shall be sealed by flame complete all as specified and directed.

S&F fully retro reflective sign board 1.0 Mtr x 0.76 Mtr board made out of 3 mm thick ACP (aluminum composite panel) sheet framed with 40 mm dia and wall thickness 2.0 mm stainless steel pipe having all sides and entire surface fully bonded with retro reflective sheeting of HIP (High Intesity Prismatc) grade having pressure sensitive adhesive. Borders and messages as indicated cut out. Background in blue and matter in white colour tape having two posts of 50mm dia wall thickness 3.0 mm stainless, steel pipe 4.50 mtr long any shape, size, design as a vertical supports and embedded in ground with PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) of size 450 x 450 x 600 mm incl necessary excavation and earth work complete and incl taking down old sign board complete all as specified and as directed. Note :One side with slogan and other side with indication as specified/directed.

M&L for 35mm thick (measured solid) precast cement concrete louvers and jallies type C-0 mix (1:3:6) (using 12.5mm graded stone aggregates) including all mouldings but excluding frame set in CM (1:6) complete all as specified and directed.

M&L for preparation of old painted surface and applying one coat of exterior emulsion paint of RCC over tank of 15 to 24m staging on outer surfaces of RCC coloumn , bracing, ring beam, surface area of dome , sides and soffit of stair case for the following location including necessary scaffolding for painting complete all as specified and directed. (a) New & Old RATC - 03 Nos (b) 1 CSR - 01 No (c) Army School - 01 No (d) HQ 1 Corps - 01 No (e) 1 CGSR - 01 No (f) EME Bn - 01 No (g) MES Colony - 01 No (h)PH No 24-01 No (j)PH No 09 - 01No (k) Near Radial well - 01 No (l) PH No 19 - 01 No (m) NHL - 02 Nos (n) Lohra Marg - 01 No Note:- The contractor has advised to visit all RCC overhead tank before quoting rates.

M&L for servicing of rolling shutter incl oiling, greasing and easing with all replacement of necessary fittings for smooth functioning of rolling shutter and with one coat of synthetic enameled paint to steel surface complete all as specified and directed.

S&F steel rolling shutters without ball bearing as specified inlcuding top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete push pull or manual type including dismantling old shutter complete all as specified and directed.

M&L for vitrified paving tiles (any colour) of size 300 x 300 x 10mm thick, with gray cement & pigment set, jointed and pointed in neat cement slurry in floors laid over and including 15mm screed bedding in cement mortar (1:4) complete all as specified and directed.

Deepak Saxena

M/s Hoti Lal Contractor

Ms Kamal Kant Agarwal