Multifarious Repairs and Restoration Work at Municipal Workshop

Amount

Multifarious Repairs & Restoration Work at Municipal Workshop.

LED Tubelight fixtures 1X 18W

Ceiling fan of 900 mm sweep with all accessories including Electronic Regulator for completing installation

Fixing of Ceiling fans Above 0.5 Mtrs. to 1 Mtr.

Removing old cement plaster of any finish from the wall, complete with racking out the joints to a depth of 20 mm.

25 to 30 mm thk. rough Shahbad stone

Wiring for submains- medium class PVC- 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire in 20mm Conduit

Providing and laying in position plain cement concrete Nominal Mix of 1:3:6 (1 Cement OPC: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Excavation for foundations, substructures, basements, tanks, sumps, walls, chambers, manholes, trenches, poles, pits & general building works in all types of soils, vegetable earth, soft murum, running sand, shingle, turf clay, loam, peat, ash, shale, slag, chalk, garbage, muddy/ marshy/ slushy soil, marine clay, reclaimed land etc. for depths/lifts upto 1.5M

LED LIGHT FIXTURE Outdoor LED Street Light fittings – 36-48 W

Providing & Laying 150 mm thick dry stone Rubble Soling with average 150 mm size hard stone set in regular lines, handpacked and interstices thoroughly filled with small chips including filling in with good quality murum brought from outside, compacting with iron rammers, watering, sand spreading 12mm thk. layer of grit on top etc

Brick work with common burnt clay modular bricks of class designation 3.5 and above in superstructure above plinth level upto floor five level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Exhaust fan of 305mm sweep, 900/1400RPM, with 750 CFM free air delivery, AC 230V/415V , 50 Hz, single phase / three phase complete with all necessary accessories for completing installation .

Providing and applying 20 mm thick external sand faced cement plaster In cement mortar 1:3 with neat cement rendering upto 10m from ground level and at all locations in cement mortar proportion specified below in two coats for masonry (except stone masonry) and concrete surfaces including providing water proofing compound to the first coat of plaster as per manufacturers specification, racking out joints, hacking of concrete surface, finishing, curing, scaffolding etc complete as directed By Engineer In Charge. Min. time lag between two coats shall be 24 hours.(as per IS 2402 of 1963.)

Providing and applying 20 mm thick internal sand faced cement plaster at all heights and locations In cement mortar 1:4

Fan safety rope/ Fan wire.

Removing mosaic, cement marble, granites non-slippery, tandur, kotah, shahabad stone or Indian Pattern stone, glazed tiles in flooring and dado including bedding brick bat coba etc., and delivering materials in Ward Office and carting away unserviceable materials.

Providing and laying 800 x 800 x 9 to 10 mm thk. Light coloured glazed vitrified tiles

Wiring for submains- casing n cap -2 X 1.5 sq. mm+ 1 X 1.5 sq. mm earth wire in 20 x 12 mm(1/2 in.)

Providing and applying first single coat of approved primer and two coats of anti-algal, anti-fungal, exterior paint as specified below of an approved make and colour as per manufacturers specifications to any surface, upto 10m height from ground level and at all locations as directed including preparing surfaces for painting by any approved means, scaffolding, cleaning and curing etc.

Providing and applying first single coat of approved primer and two coats of acrylic plastic emulsion paint of an approved make and colour as per manufacturers specifications to any surface, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting by any approved means etc. complete as directed by Engineerin-charge.

Wiring for submains- medium class PVC- 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire in 20mm Conduit

Providing and fixing single skin trapezoidal profiled sheeting 930 - 1020mm cover width 28-32 mm crests depth at 186-250 c/c ( above 195 mm c/c crest distance there will be minimum 2 ribs at the centre for stiffening)

Providing, detailing, and fabricating as per specifications, transporting to site and erecting M.S. ladder using hot rolled sections, hollow pipes (Hollow pipes conforming to IS 1239 part 1 and 2)

Removing doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below

S' type M.S. fan hook fabricated from suitable dia. M.S. rod & suitable size M.S. brackets, nut bolts, washers for fixing ceiling fan on trusses. The 'S' type hook & bracket shall be painted in approved manner.

Providing and fixing superior quality factory made phenol bonded solid core single leaf flush commercial door shutter of thickness 25mm thick shutter

Providing and fixing in position two track aluminum window of extruded modular and anodized aluminum sections of approved make and of size 61.85 mm x 45.5 mm x 1.3 mm thk (wt 1.055 kg/Rm) for bottom, 61.85 mm x 31.75 mm x 1.3 mm thk. (wt 0.659 kg/Rm) for top & sides, mounted on anodized aluminum rectangular frame of size 63mm x 38mm x 2.0mm(1.054). The shutter comprising of bearing bottom and top of size 40mm x 18 mm x 1.25 mm thk (wt. 0.417 Kg/Rm) Interlocking section of size 40mm x 26,7 mm x 1.10 mm thk. (Wt. 0469 kg./Rm) and hand sides of 40mm x 18mm x 1.25 mm thk (wt. 0.417kg/Rm) with 5 mm thick plain / frosted / tinted glass fixed in shutter including approved quality neoprene gasket, fixtures, fastenings and accessories like PVC rollers, PVC weep holes, locks, handles etc.

Providing and fixing anodized (anodic film must not be less than 15 microns i.e. 6mm Acrylic sheet

Light /Fan / Ex. fan Points

2/3 Pin Independent Plug (IP)

R J INFOTECH (BID ID -6471413)