AMC FOR ELECTRICAL WORK OF LAB AREA BUILDINGS AT CSIR CSIO CAMPUS SECTOR 30 CHANDIGARH

Amount

Sub Head-I :- Man Power Note:- Before Quoting the rate, contractors should be ensured that Basic Per Month Rate for Item No.1 and 2 should not be less than Rs.95136.00 and Rs.84572.00 per month, respectively. This is the minimum saturatory requirement amount for compliance of the labour laws, which is based upon latest minimum wages declared by DC Chandigarh for w.e.f. 1st April'2019 + EPF@13% + ESI @3.25% + Bonus @8.33% + GST@12% + 1% labour cess but without contractor profit. Further, Contractors are advised to quote the rate by adding suitable service charges/overhead charges amount over the above mentioned minimum amount , as per their convenience. If the per month rate quoted by the contracror found below the above mentioned rates then the tender will be rejected straight way. Note:-The payment on account of enhancement/escalation charges on account of revision in wages by DC, Chandigarh Administration from time to time shall be payable by the CSIR-CSIO to the contractor.

Deployment of Electrician/Technician - 04 Nos. for day to day electrical operation, upkeeping and and general maintenance work in lab area, at CSIR-CSIO campus, Sector-30, Chandigarh.

Deployment of semi skilled Helper/Assistant Electrician-04 Nos. for day to day electrical operation, upkeeping and and general maintenance work in lab area, at CSIR-CSIO campus, Sector-30, Chandigarh.

Sub Head-II :- Supply of material Following material will be supplied during the execution of maintenance work (to be used by the above stated deployed man power) from time to time as and when required.Specification and make of the material will be used as per annexure attached.

Piano type one way switch 5/6 A

Piano type two way switch 5/6 A

Piano type switch 15/16 A

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Modular one way switch 5/6 A of different Make/models as per requirement.

Modular switch 15/16 A of of different Make/models as per requirement.

3 pin 5/6 A modular socket of different Make/models as per requirement.

6 pin 15/16 A modular socket of different Make/models as per requirement.

PVC Batten/ Angle Holder any one of make Anchor model Anchor/ Deluxe / Penta NOA.

Three pin plug top 5/6 amps, 230/250 volts, 50Hz ISI marked Anchor / SSK make

Three pin plug top 15/16 Amps, 230/250 volts, 50Hz ISI marked Anchor / SSK make.

Capacitor of rating 2.5 mf to 4 mf, single phase, 240/440 volts anyone of make Asian EPCOS / Bajaj / CG

Two modular rotory stepped type electronic fan regulator suitable for 230/250 Volts, 50Hz, single phase AC supply .

LED Batten of rating 20W, minimum lengh 1150mm, lumens effieciency not less than 100lm/watt, suitable for 230V, 50 Hz, single phase AC Supply, complete as required. Make Havells/CG/Philips.

Tube starter suitable for FTL fitting 36/40 watts, 230/250 volts, 50 HZ. ISI marked any one of make Bajaj / Philips / CG.

Tube fitting side holder, single-phase 230 volts any one of make Bajaj / Anchor /Philips / CG.

Fluorescent lamp (tube rod ) 4 feet long, 36/40 watts, 230/250 volts, 50 Hz anyone of Make: Phillips/Bajaj/CG make as required.

Tube rod 1X28 watts, T-5 ,4 feet long any one of Make: Phillips/Bajaj/CG make as required.

Tube rod 1X14 watts, T-5, 2 feet long any one of Make: Phillips/Bajaj/CG make as required.

Electronic tube ballast/chock 1X36/40 watts, 230/250 volts 50 Hz. Bajaj Rezo models Philips/CG make. Compact and ordinary models.

Electronic tube ballast/chock 1X28 watts, 230/250 volts 50 Hz. Bajaj Rezo models Philips/CG make. Compact and ordinary models.

Electronic tube ballast/choke 4X14 watts, T5, 230/250 volts 50 Hz. Bajaj/Philips/CG make. Compact and ordinary models.

LED lamp of Pin/screw type, 7-10 Watt, single phase, 230V, 50Hz any one of make CG/ Osram/ Philips.

LED lamp 14-15 Watt, Pin/screw type, single phase, 230V, 50Hz any one of make CG/ Osram/ Philips.

LED lamp 23-25 Watt, Pin/screw type, single phase, 230V, 50Hz any one of make CG/ Osram/ Philips.

PVC insulated, FRLS, single core copper conductor cable 1.5 sq. mm ISI marked, any one of make Ecko/Havells/Ralison /Anchor.

PVC insulated, FRLS, single core copper conductor cable 2.5 sq. mm ISI marked any one of make Ecko/Havells/Ralison /Anchor.

PVC insulated, FRLS, single core copper conductor cable 4.0 sq. mm ISI markedany one of make Ecko / Plaza / Ralison Anchor.

PVC insulated, FRLS, single core copper conductor cable 6.0 sq. mm ISI marked, any one of make Ecko / Plaza / Ralison Anchor.

PVC insulated Twin core flexible cable size 30/0.25mm (1.5 Sq.mm.) copper conductor, 1.1Kv grade, ISI marked any one of make ECKO / Empire / National /Kinjal/Arr Kay Lite.

PVC insulated three core flexible cable size 50/0.25mm (2.5 Sq.mm) copper conductor multi stand 1.1KV grade any one of make ECKO/ Empire/ National/ Kinjal/ Arr Kay Lite.

PVC insulated 3 Core flexible cable size 84/0.3mm (6 Sq. mm) copper conductor multi stand 1.1 KV grade any one of make ecko empire National /Kinjal.

One no. PVC insulated and PVC sheathed/ XLPE 1.1 kV grade, armoured aluminium conductor cable of size 4x10 sq. mm ISI marked anyone of make Ecko/ Ralison/ Citirana/ KEI/ Havells.

PVC conduit Pipe 25 mm dia. of medium class, ISI marked.

MS flexible pipe 25 mm dia. with PVC coating along with all ancillaries and accessories like coupler etc. as required.

PVC flexible pipe 20mm to 25mm dia. of good quality as approved.

PVC batten of size 25 mm X 10 mm (casing & capping) ISI marked any one of make Diplast / Anchor or equivalent make.

U-PVC adaptable trunking system of size 100mm X 50mm complete with trunking cover etc. for housing the electrical modular box for fixing modular switch sockets, telephone socket etc, on the wall/tables/pillars etc. as required.

PVC moduler box 6 to 8 modules with cover plate and blanking plate suitable for fixing in 100mmx50mm DLP U-PVC trunking for fixing the moduler switch and socket 5amp./15amp. Complete as required at site.

PVC gang box suitable for 2 switches and 2 sockets of 5amp. Complete in all respect as required at site.

PVC gang box suitable for 1 switch and 1 socket of 15amp. Complete in all respect as required at site.

Minor material like iron staples/ saddles/ screws for fixing of bakelite sheet with MS boxes, PVC pipe, flexible pipe etc. as required.

Miniature circuit breaker of rating 5 A to 32 A, 10 kA, “C” curve, single pole, 240/415 V, suitable for inductive load as required.

Miniature circuit breaker of rating 5 A to 63 A,10 kA, “C” curve, double pole, 240/415 V, suitable for inductive load as required.

Miniature circuit breaker of rating 5 A to 63 A, 10 kA, “C” curve, Triple Pole & Neutral , 240/415 V, suitable for inductive load as required.

Isolator 63Amp, four pole, 415 V, as required.

Residual current circuit breaker (RCCB), 63 Amp., four pole, (three phase and neutral), 415 V, having a sensitivity current 30 mA as required.

MCCB of rating 80-100 Amps, 4 pole, 25 KA breaking capacity, Make: L&T/ C&S as required.

SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps 'C' series, SP, MCB, in sheet steel enclosure as required.

Timer switch Series FM/1 Quartz Type QT(Daily)Single phase 230/ 240 volts 50/60 Hz GIC/ L&T make suitable for street light controls.

LED Flood Light, 50 Watt, single phase 230V, 50Hz complete in all respect any one of make CG/ Osram/ Philips.

LED Flood Light, 80 Watt, single phase 230V, 50Hz complete in all respect any one of make CG/ Osram/ Philips.

LED street light fitting 36/40 Watt, single phase 230V, 50Hz complete in all respect any one of make CG/ Osram/ Philips.

LED street light fitting 72/80 Watt, single phase 230V, 50Hz complete in all respect any one of make CG/ Osram/ Philips.

LED type street light fitting driver/ controller of 36/40 watts and LED plate 36 watt complete in all respect as required at site.

LED type street light fitting driver/ controller of 72/80 watts and LED plate 72 watt complete in all respect as required at site.

DOL starter complete set in sheet steel enclosure of 3-phase 415 volts for 3 HP-10 HP Motor control, Make: L&T/Schneider as required.

Water level sensor controllar, float type as approved as required at site.

Ball bearing of size from No.6200 to 6203 anyone of make NBC/ CG/ SKF/ TATA

SUB HEAD-III: PETTY JOBS

Charges for rewinding of ceiling fan of size 1200/1400 mm sweep of USHA/ Kessle/ Khaitan/ CG make of different models complete in all respect up to working condition of ceiling fan.

Charges for repair, and overhauling of single phase ½ HP rating mono block pump set complete in all including all material like bush/ capacitor/ bearing of etc. upto running condition of motor at site.

Charges for rewinding of single phase ½ HP rating mono block pump set including repair of pump, shaft, seal bearing etc. and complete in all respect upto running condition of motor as required.

Charges for rewinding of Exhaust fan / Wall fan size 12”-18” (300mm-450mm sweep) complete in all respect up to working condition.

Charges for repair/overheauling/replacement of bearings including extra material like fledge/ gaskets, nut & bolts etc for 3-phase water booster pumps/motors of rating 3 HP to 5 HP, 415 volts including dismantling and Re-erection of the motor at site any one of make Crompton Greaves/ Kirlosker.

Changes for Rewinding of 3-phase water booster pumps/motors of rating 3 HP to 5 HP, 415 volts including dismantling and Re-erection the motor at site including all material like fledge/ gaskets, nut & bolts etc any one of make Crompton Greaves/ Kirlosker.

Alluminium Painting of street light pole from size 3 metre to 9 metre GI/Tuber type pole including white washing of cement muff and red/gray painting of connector box of street light pole complete in all respect as required at site.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and Laying of 6 SWG GI cable at 0.50 Metre below ground level for conductor earth electrode, including soldering etc. as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade upto 35 sq. mm. direct in ground including excavation, sand cushioning, protective convering and refilling the trench etc. as required.

Providing and laying cement concrete 1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) in muffs of Dia 15 inche and height 2 feet approx. for street light poles , including of Centering and shuttering including strutting, propping etc. and removal of form and 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) complete as directed by Engineer in charge. It also includes breaking of existing RCC muff and shifting of material from site as required.

FAIR DEAL ENGINEERS