SPECIAL REPAIR TO BLDG NO P-66 AND P-67 AT KANJOLI LINE AT BHARATPUR MIL STN

Amount

Taking down chowkats or frames with shutters not exceeding 1.50 Sqm each (without taking off shutters from the frames) etc complete all as specified and directed.

Taking down chowkats or frames with shutters exceeding 1.5 sqm but not exceeding 4.00 sqm each (without taking off shutters from the frames) etc complete all as specified and directed.

Taking down chowkats or frames with shutters not exceeding 4.00 sqm each (without taking off shutters from the frames) etc complete all as specified and directed.

Resecuring or easing & adjusting, without taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each etc complete all as specified and directed.

Resecuring or easing & adjusting, without taking down shutters of any description exceeding 2 sqm each etc complete all as specified and directed.

Taking down Shutters of any description exceeding 1 sqm but not exceeding 2 sqm each and refixing in same opening etc complete all as specified and directed.

Taking down Shutters of any description exceeding 2 sqm but not exceeding 4 sqm each and refixing in same opening etc complete all as specified and directed.

S&F 30mm flush shutters, solid core construction, single or double leaved rebating shall be square or splayed ,with block board core and playwood face panel free from twist or wrap in plane, both faces are covered with decorative face veneer with internal wooden frame lipping not less than 50mm etc complete all as specified and directed.

S&F of 35 mm thick 2nd class hardwood (hollock) factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete. The shutter shall be fitted to chowkhat as directed by Engineer-in-Charge.

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixing in opening etc complete all as specified and directed.

S&F of 30mm thick factory made PVC factory made PVC rigid foam panelled door shutter made out MS square tube of min 19 gauge thickness and min 19mmx19mm for styles and 15mmx15mm for top and bottom rails MS frames to be given a coat of steel primer of approved make MS tube to be covered by PVC sections as under:- (a) Styles -`C' channels of thickness 5mm (min) size 30x75mm (b) Top rail 5mm (min) thickness 75mm wide sheet on either side and 5mmx20mm cross PVC sheet. (c) Bottom rail-5mm thick (min) x125mm wide sheet on either side and 5mmx20mm cross PVC sheet. (d) Lock rail-5mm thick (Min) x75mm wide sheet on either side. Panelling sheet should be of min 5mm thick PVC rigid foam sheet. The panelling sheet shall be fixed to the styles and rails with 5mm thick and 2mm thick PVC sheet beading. (e) The fixing of PVC Doors shall be all as per manufacturers instructions and directed.

M&L in repair 19/20 mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice laminations , fixed with screws to timber frame work etc complete all as specified & directed.

S&F continuous (piano) hinges, brass, bright finish or electro galvanised with width of flap (when open) 30mm etc complete all as specified & directed.

S&F in repair brass Locks 4 levers, cupboard, grade 1, of size 65 mm etc complete all as specified & directed.

S&F of mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, door chowkhat of angle or other section and similar works complete of Gde Fe-290 Gde E-165 including welding etc. complete all as specified and directed.

S&F of MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position etc complete all as specified and directed.

S&F 300mm long bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type)and fixing clips of sheet, cast or extruded sections and fixing bolts and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and directed.

S&F 200mm long bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type)and fixing clips of sheet, cast or extruded sections and fixing bolts and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodised etc complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section and fixed length of bolt 150mm etc complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section and fixed length of bolt 200mm etc complete all as specified and directed.

S&F of 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkhat including welding etc complete all as specified and directed.

S&F of 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkhat including welding etc complete all as specified and directed.

M&L for providing cement concrete(1:2:4) B1 type using 20mm graded stone aggregate ,in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses parapets and railings upto 60 cm in heights coping kneelers, apex stone bed plate, water trough and the like including weathering, slightly chamfered angles and throating including necessary formwork all as directed by Engineer-in-Charge.

M&L for treating back of chowkats of wood and wood based materials steel and iron work including preparing surfaces new or old and treating ends of posts hacks of chowkats etc area tarred exceeding 0.1 sqm but not exceeding 0.50 sqm each and treated with tar or coal tar black paint etc complete all as specified and directed.

S&F of small fitting such as brackets of any type latch and hinge blocks shaped door and window stops and the like not exceeding 200 cum each of second class hard wood including all necessary labour complete as directed by Engr-in-Charge.

Supply only 50 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkhat including welding etc complete all as specified and directed.

M&L for painting new or previously untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over one shop coat of zinc chrome primer including preparation of surfaces. etc complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified & directed.

M&L brick work with fly ash brick straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/ brick surfaces including raking out joints hacking for key scrubbing down with water including removal to debris to a distance not exceeding 100 m and deposited where directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in two layer of 10mm thick in CM (1:6) and second layer 5mm thick in CM (1:4) mixed with WPC @ 3% weight of cement on stone masonry surfaces or surfaces other than fair face of brick wall or concrete surface finished even& smooth without using extra cement etc complete all as specified and directed. Note:- WPC shall be measured and paid separately under respective item.

M&L for rendering 10mm thick in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) stone masonry surfaces or surfaces other than fair face of brick wall or concrete surface finished even& smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:4) on concrete surfaces including finished even & smooth on ceiling etc complete all as specified and directed.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings etc complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall by washing,rubbing down and applying two coats of oil emulsion distemper over a coat of wall care putty on wall etc. complete all as per specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of Oil bound distemper over a coat of alkali resistant primer etc complete all as specified and as directed.

M&L for preparing new plastered surfaces and applying three coats of white wash on wall etc. complete all as per specified and directed.

M&L for preparing new plastered surfaces and applying three coats of white wash on ceiling etc. complete all as per specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer on wall etc. complete all as per specified and directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of wall care putty on walls etc complete all as specified & directed by Engineer-in-Charge.

M&L for preparing old plastered surfaces and applying two coats of oil bound distemper over a coat of primer on ceiling etc complete all as per specified and directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer on walls etc complete all as specified & directed by Engineer-in-Charge.

M&L for preparing old plastered surfaces and applying three coats of white wash on wall etc. complete all as per specified and directed.

M&L for preparing old plastered surfaces and applying three coats of white wash on ceiling etc. complete all as per specified and directed.

Demolition Cement concrete (reinforced) concrete of any description and in any position not otherwise specifically provided etc complete all as specified and directed.

Demolition Cement concrete (unreinforced) concrete of any description and in any position not otherwise specifically provided etc complete all as specified and directed.

M&L 75mm thick cement concrete type B-1 (1:2:4) using 20mm graded aggregate in flooring finished even and smooth without using extra cement etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiling to store and rubbish off the premises etc complete all as specified and directed.

S&F coloured glazed ceramic tiles first quality of size (300x450)mm, 7 to 8 mm thick , in vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match shade of tiles and including providing 15mm thick backing coat in CM (1:4) etc complete all as specified and directed.

M&L non skid ceramic tiles (coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including providing 15mm thick screed bed in CM (1:6) etc .complete all as specified and directed.

M&L vitrified ceramic (light shade) coloured tile of 10 mm thick square/rectangular polished area of each tile not exceeding 0.36 sqm in floor etc set and jointed in neat coloured cement to match the shade over and including providing 15 mm thick screed bed in CM (1:6) etc complete all as specified and as directed.

M&L vitrified ceramic (light shade) coloured tile of 10 mm thick square/rectangular polished area of each tile not exceeding 0.36 sqm in skirting and dado etc set and jointed in neat coloured cement to match the shade over and including providing 10 mm thick backing coat in CM (1:3) etc complete all as specified and as directed.

M&L of 20 to 25mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and rounding the edges etc complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as specified & as directed.

M&L machine cut kota stone slab flooring as in staircase 20-25 mm thick laid over 20 mm thick cement screed base laid in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grooving, rubbing and polishing etc complete all as specified & as directed.

M&L machine cut kota stone slab flooring 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over 10 mm thick cement plaster laid in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified & as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe in 15mm.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe in 20mm.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe in 25mm.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) bore dia pipe in 15 mm.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) bore dia pipe in 20 mm.

M&L in repair new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of bore of tube 15mm etc complete all as specified & as directed.

M&L in repair new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of bore of tube 20mm etc complete all as specified & as directed.

M&L in repair new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of bore of tube 25mm etc complete all as specified & as directed.

S&F in repair fancy type chromium plated bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore etc complete all as specified & as directed.

Taking down the existing unserviceable stop valve and providing supply and fixed stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed of bore dia of pipe in 15mm etc complete all as specified & as directed.

Taking down the existing unserviceable stop valve and providing supply and fixed stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed of bore dia of pipe in 20mm etc complete all as specified & as directed.

S&F in repair angle stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated dia (or bore) of pipe in 15mm etc complete all as specified & as directed.

S&F in repair angle stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated with long shank and cup (concealed type) dia (or bore) of pipe in 15mm etc complete all as specified & as directed.

S&F in repair 15mm brass chromium plated 3 in 1 mounted on wall for mixing hot & cold water screwed down for iron pipe and fixed etc complete all as specified & as directed.

S&F fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore including taking down old pillar tap etc complete all as specified & as directed.

S&F in repair vitreous china wash hand basin white of size 550x400mm flat back excluding taps, waste, chain and plug but including brackets including cutting for and pinning in ends of brackets or erecting stand including dismantling of old existing unserviceable WHB glazed etc complete all as specified and directed.

M&L Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms bore dia of discharge pipe 32mm etc complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres capacity with inlet ball valve float & handle, syphonic action type including brackets & flush pipe of polyethylene of low or high density or PVC 32mm dia for low level flushing cistern fixed in repairs.

S&F in repair 125mm size brass chromium plated shower rose etc complete all as specified and directed.

S&F in repair Vitreous China Wash down water closet pan pedestal pattern white in colour, and including plastic water closet seat, closed pattern with flat bottom and cover and MS chromium plated hinging device including connection to outgoing pipe and flushing pipe etc complete all as specified & directed by Engineer-in-charge.

S&F in repair toilet paper holder, vitreous china white ,box type to wall with CP brass screws etc complete all as specified & directed.

S&F in repair soap dish vitreous china white of size 160mmX160mmX90mm etc complete all as specified & directed.

S&F in repair aluminium anodised tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges etc complete all as specified and directed.

S&F in repair MS chromium plated grating 125mm dia of weight not less than 50gms for floor trap / Nahani trap. etc complete all as specified and directed.

Disconnecting existing tanks of capacity in litres exceeding 250 litres but not exceeding 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes, etc complete all as specified and directed.

Removing building materials etc. to a distance of exceeding 100 m but not exceeding 2 Km, beyond the lead included in the rates, including loading and stacking at the destination etc complete all as specified and directed.

Water proofing treatment shall be carried out as under :-

(a) Cutting or uprooting grass on old mud phuska removing rubbish off the promises cleaning surface and preparing to receive new treatment etc complete all as specified and directed.

(b) M&L 20 mm thick screed bed or bedding layer of cement mortar (1:4) finished even and smooth without using extra cement etc complete all as directed by Engineer-in-Charge.

(d) M&L for 40mm thick PCC type B-0,( 1:2:4) using 12.5 mm graded stone aggregate with integral water proofing compound as per manufacturers specification with galvanised chicken wire mesh ensuring a gradient min 1:80 towards drain. After the application of screed, provide contol joints along the length and breadth of entire screed area. The joints can be provided by using a saw cutting machine attached with a 3 mm blade. The joints will be 12 mm deep. 28-30 days later the joints shall be filled with elastomeric sealant as per manufacture’s instruction.

(c) M&L for preparing surfaces for roof treatment by removing all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surfaces mechanically or by grinding to make it smooth before application, repair all cracks by cutting "V" groove and fill with PMC mortar (Polymer modified cement mortar) prepared in ratio as per manufacturers specification, provide 75 mm x 75 mm coving made out of PMC mortar as above on all joints of vertical up stands to ensure that moisture content in the prepared surface does not exceed 5% immediately before application of liquid membrane. Material incorporation & Protection be provided as terrasheild first apply with water (ratio terrasheild : water will be 4:1) as primer with coverage area 0.1 Kg per Sqm. After 2-3 hour later, second step apply directly first coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller. Spread non woven geo textile of 40 / 50 gsm with overlap of 50 mm in both direction when the surface is still tacky. After 4-6 hour later, apply third step apply directly second coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller. final thickness of complete treatment should be minimum 1.0 mm. Water tank and Khurra location one additional coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm be provided. after complete application full curing minimum 7 days . Above complete application will be done authorized applicator from Manufacturer and manufacturer's specification. Make of IWL / STP/Pidilite or equivalent. Note:-WPC shall be measured and paid separately.

Supply only Integral water proofing compound.

S&F in repair UPVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor, type 'B', ISI marked of 110mm bore etc complete all as specified and directed.

S&F in repair UPVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, type 'B', ISI marked of 110mm bore etc complete all as specified and directed.

S&F in repair UPVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor, type 'B', ISI marked of 75mm bore etc complete all as specified and directed.

S&F in repair UPVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, type 'B', ISI marked of 75mm bore etc complete all as specified and directed.

S&F in repair UPVC (SWR) bend of any radius of 110mm bore etc complete all as specified and directed.

S&F in repair UPVC (SWR) bend of any radius of 110mm bore etc complete all as specified and directed.

S&F in repair UPVC (SWR) single junction (Single T) of 75mm bore etc complete all as specified and directed.

S&F UPVC (SWR) vent cowl of 110mm bore etc complete all as specified and directed.

M&L Granolithic concrete (1:1:2) floor topping 30mm thick; laid over cement concrete like facia, column, slab, chhajja etc. and finished to an even and fair surface including roughening surfaces of old concrete by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0kg of cement per sq. metre etc complete all as specified and directed.

S&F harrison rails anodised aluminium alloy with fancy type fixing brackets, stops, rollers etc. complete all as specified and directed.

Cutting channels, grooves or rebates not exceeding 15cm girth, and trimming surface With or without reinforcement etc. complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws etc complete all as specified and directed.

S & F in repair sink with drainage board made of stainless steel 1 mm thick kitchen with plug, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 mm X 460mm bowl size 410 mm X 330 mm X 160 mm etc complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack of overall minimum size 900 x 750 x 225mm with partitions for small/ large plates etc made out of stainless steel 24 gauge, fixed with rawl plug and CP steel screws all as directed of approved quality etc complete all as specified & directed.

M&L for 100mm thick Sand stone slabs in sun - shades, chajjas, shelves, cills, landings, cover stones templates, etc. not exceeding 2 m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in lime mortar (1:2) or cement mortar (1:4)complete all as specified and directed.

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

Taking down carefully surface aluminium or copper point wiring with PVC casing capping or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces etc complete all as specified & directed.

Taking down carefully sub main wiring with PVC casing capping / PVC surface conduit and service wiring with making good surface etc complete all as specified & directed.

Taking down carefully unserviceable rusted main switch/DB of any size capacity and make etc. complete all as specified and directed.

M&L point wiring complete with 1.5 sq.mm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in PVC conduit pipe with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface of wall/ceiling by means of PVC sleeve/dash fasteners with cadmium plated screws including suitable size of PVC boards/ existing sunken box for mounting fittings like switches, sockets, fan regulator etc including 1.5 sq.mm insulated but unsheathed copper earth continuity conductor to common earth and connected to earth dolly etc complete all as specified and directed for the following :-

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One bell/buzzer point controlled by one push button

(d) One 3 pin 6 Amp switch socket outlet on the same board with other switches

(e) One 3 pin 6 Amp switch socket outlet on the independent board

All as per item No 112 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps switch socket outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly etc complete all as specified and directed

S&F switch socket combination 2 in 1, 6 Amps multi-purpose flush type 230 volts etc. complete all as specified and directed.

S&F switch socket combination 2 in 1, 16 Amp flush type multi-purpose 230 volts etc. complete all as specified and directed.

S&F switch piano flush button single pole one way 6 Amp 230 volts etc. complete all as specified and directed.

S&F ceiling rose surface bakelite 50mm x 40 mm three terminal ISI marked including suitable size of PVC board etc. complete all as specified and directed.

S&F bell multi musical type 230 volts grade etc. complete all as specified and directed.

S&F step type electronic fan regulator EME type 450 watts etc. complete all as specified and directed.

S&F modular socket 6 amp 2/3 pin combined 2 module etc complete all as specified & directed.

S&F modular socket 6/16 -2/3 pin combined 2 module etc complete all as specified & directed.

S&F modular switch one way, SP, 6 amp, 1 module etc complete all as specified & directed.

S&F modular switch one way, SP, 16 amp, 1 module etc complete all as specified & directed.

S&F modular bell push, flush type 6 amp, 1 module etc complete all as specified & directed.

S&F modular hum free electronic step fan regulator, 120 watts, 2 module etc complete all as specified & directed.

S&F white cover plate with frame 2 module etc complete all as specified & directed.

S&F white cover plate with frame 3 module etc complete all as specified & directed.

S&F white cover plate with frame 4 module etc complete all as specified & directed.

S&F white cover plate with frame 6 module etc complete all as specified & directed.

S&F white cover plate with frame 8 module etc complete all as specified & directed.

S&F metal flush box 2 module etc complete all as specified & directed.

S&F metal flush box 3 module etc complete all as specified & directed.

S&F metal flush box 4 module etc complete all as specified & directed.

S&F metal flush box 6 module etc complete all as specified & directed.

S&F metal flush box 8 module etc complete all as specified & directed.

M&L submain wiring complete with 10 Sq.mm single core multi standard PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 10 Sq.mm copper cable for earth continuity conductor in and including drawn through PVC casing capping PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc. complete all as specified & directed.

S&F of Distribution board factory made and tested made of sheet metal enclosure, powder coated suitable for mounting the MCB 240 volt of the following size:-

(a) 4 way SPN with 200 Amps rated busbar 240 volts (double door type)

(b) 8 way SPN with 200 amps rated busbar 240 volts (double door type).

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of following ratings:-

(a) Single pole 10 to 32 amps

(b) Single pole Neutral 40 amps

(c) Single pole Neutral 63 amps

S&F Linear LED T8 tubular lamp of 20 watt with extruded aluminium body, PC diffuser and inbuilt driver with Batten suitable for LED T8 lamps , complete with all accessories internally pre-wired and including connecting to ceiling rose with three core flexible copper conductor cable of size 1.0 sq.mm of Make: Crompton Cat Part No: DIJB12LT8-20 and Lamp Cat Part No:LGT8-20-865-2 or equivalent as mentioned in Appx’B’

M&L for batten holder insulated with back plate including suitable size of PVC round block complete.

S&F galvanised pipe 40 mm bore medium grade ISI marked with fittings as required etc complete all as specified & directed.

M&L for earthing with galvanized steel earth plate electrode 600mmx 600mmx6mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with the top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No. 03 of SSR Part -I connected to earthing point and including 15mm bore light grade G.I. protection pipe (up to 7.5 meter from edge of the pit), PCC pit in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40mm thick cover, watering arrangement with funnel and wire mesh and 20mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work including testing on completion.

M&L for One light point controlled by two, 2 way switches, with copper conductor cables 1.5 sq. mm size etc complete all as specified & directed.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine for laying underground pipe etc complete all as specified & directed. Note :- GI pipe shall be measured and paid in respective item.

Taking down carefully unserviceable underground cable PVC insulated armoured PVC sheathed aluminium conductor, LT cable any size and make etc. complete all as specified and directed.

S&F 20 watts LED street light fittings new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP66 with 10 KV surge protection roadway, luminaries with high power LED as light source with warranty option of 5 years and suitable drivers etc and connecting with 4 sqmm multistranded aluminium conductor PVC insulated twin core weather proof cable from fittings to over head lines oe to the junction box and fixing to complete all as specified and directed of make Crompton cat ref No LST-20-CDL-M or equivalent as mentioned in Appx’B’

Refixing only serviceable LED fitting 1X20 watts including connecting wire upto ceiling rose at same place after repair of wall and roof etc complete all as specified and directed

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good cutting not exceeding 10 cm girth in stone concrete block or slab wall.

S&F sheet metal enclosure of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of SP 20 Amps, 240 volts etc complete all as specified & directed.

S&F LED mirror light fitting 1 x 14 watts, 230 volts attractive wall/ ceiling mounted type with decorative grey end caps, polycarbonate body and ribbed opal diffuser, metallic channel and white reflector suitable for mirror fitting, complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable 0.5 Sqmm size etc complete all as specified & directed. Make-Crompton Code No LCL-14-CDL or equivalent as mentioned in Appx’B’

S&F LED light fitting 14 watts, 230 volts decorative wall mounting type with multicolour ABS housing with poly carbonate rings and glass shade with lamp holders connector block etc complete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size etc complete all as specified & directed. Make: Havells Cat No LHFOECE1TZ1O014 or equivalent as mentioned in Appx’B’

M&L submain wiring complete with 6 Sq.mm single core multi standard PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 6 Sq.mm copper cable for earth continuity conductor in and including drawn through PVC casing capping PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc. complete all as specified & directed.

M&L submain wiring complete with 4 Sq.mm single core multi standard PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 4 Sq.mm copper cable for earth continuity conductor in and including drawn through PVC casing capping PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc. complete all as specified & directed.

M&L submain wiring complete with 2.5 Sq.mm single core multi standard PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 2.5 Sq.mm copper cable for earth continuity conductor in and including drawn through PVC casing capping PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc. complete all as specified & directed.

Supply and laying or fixing on wall or passing through pipe testing and commissioning 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape / wire armoured underground stranded aluminium conductor cable of size 50 sq mm 3.5 core complete all as specified & directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, etc or for shaft, well, cesspit, manhole, pier holes etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out hard/dense soil.

Returning filling with earth obtained from excavation including spreading watering and consolidation in layers not exceeding 25 cm thick .etc complete all as specified & directed.

Removal of excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point .etc complete all as specified & directed.

M&L for unwashed dry river sand for sand cushioning and covering the underground cable etc complete all as specified & directed. Note :- Punning thickness shall be measured.

M&L for brick protection with brick common burnt clay building bricks ; sub-class 'B' designation 75 old size bricks flat over cable perpendicular across the cable in trenches .etc complete all as specified & directed.

S&F or laying galvanised steel water tubing medium grade with all fittings and fixed complete for protection of underground cable on pole/walls under road crossing of size bore of tube 50mm etc complete all as specified & as directed.

S&F street light GI bracket of 0.6 mtr long made out of 40mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of FL 40 x 6mm including nuts bolts & washers complete necessary fixing arrangements on pole as directed.

M&L for providing TV socket/telephone point drawn in and including separate conduit concealed in wall surface etc complete all as specified & as directed.

M&L for TV cable for dish/cable connection etc complete all as specified & as directed.

Supply and install commissioning and testing of distribution cum meter box indoor type, wall mounted factory made out of CRCA sheet thickness not less than 2 mm duly powder coated suitable for 4 No energy meter with provision of independent housing to each meter making of qtr No on meter with each compartment to MCB TPN, power control wiring with minimum 10 Sqmm copper single core cable for each control from main MCCB to meter and 6 Sqmm copper single core cable from meter to MCB SPN cable, gland suitable for distribution cum meter box with display glass to check the meter reading including disconnecting and taking out existing U/S meter box and making good to disturbed surfaces complete including following accessories all as specified and directed. INCOMING : (a) MCCB 160 Amps TPN 36 KA with adjustable setting-01 No. (b) Copper bus bar TPN 300 Amps current rating – 1 set. OUTGOING : (a) MCB SPN 63 Amps – 08 Nos (b) MCB SPN 32 Amps – 08 Nos (c) Housing/compartment with 3 phase smart energy meter capacity upto 60 Amps with in built GPRS/RF communication module for automatic metering. Complete -04 Nos (d) MCB SPN 10Amps -01 No for stair case (e) RYB indication lamp – 01 Set.

M&L for providing telephone cable 2 pair 0.4mm thick etc complete all as specified & as directed.

M&L date concentrator unit with (RF and GPRS communication) including monthly data SIM charges software has already exist etc complete all as specified & as directed.

Schedule of Credit

M/S MAKHIJA TRADERS

krishna Associate