SPECIAL REPAIR TO BLDG NO KND-54 AND OTM BLDG NO KHY-54 AT JUTOGH CANTT UNDER GE (I) JUTOGH

Amount

Demolition of cement concrete (un- reinforced) in ground floor and paving n. exc 15 cm thick below or above round level complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as specified and directed.

Dismantling of RCC shelf other than ground floors and similar suspended works complete all as specified and directed.

Taking down cement plaster of any description on brick wall surfaces etc including raking out joints hacking for key , scrubbing down with water etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L for brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick built in CM 1:4 with sub class 'B' bricks of class designation 10 (minimum compressive strength of brick 100 kg/Sqcm) complete all as specified and directed.

M&L for rendering 10mm thick on stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement required necessary scaffolding, complete all as specified and directed.

M&L for rendering 15mm thick CM 1:4 on fair face of brick ,hollow block, concrete surface finished even and fair without using extra cement & required necessary scaffolding from GL to SF, complete all as specified and directed. Note: WPC Shall be measured and paid separately.

M&L for 5mm thick rendering in CM 1:3 on concrete surface of chajjas or ceiling, finished surfaces reqiured necessary scaffolding from GL to SF, complete all as specified and directed.

M&L Non Skid ceramic tiles (coloured) 400x400x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6) complete all as spd & as directed.

M&L for 1st quality, glazed ceramic coloured tiles 350x250x 7mm/450x350x 7mm thick on verticle surface of walls with neat cement slurry @ 3.00 Kg / Sqm incl pointed in white cement with pigment to match the shade of tiles, over and incl scrceed bed 10mm thick 1:4, complete all as specified and directed.

M&L for black polished granite self ,windows cill,or on cooking platform 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick cement screed bed in CM(1:6) complete all as specified and directed. Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achieve the desired granite finish all as spfd.

M & L for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in shelves / slabs and like with and incl use and waste of necessary form work complete all as specified and directed.

M&L for MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annamled) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for MS TMT Bars 8 mm dia cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

Taking down chawkhat or frame with (without taking of shutters from the frames) exc 1.50 sqm but n. exc 4sqm complete all as specified and directed.

All as per Srl Item No 18.00 above but for n.exc 1.5 sqm, complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm from chowkhat and removing to or from store as required complete all as specified and directed.

Taking down shutters of any description ,n.exc 1 sqm from chowkhat and removing to or from store as required complete all as specified and directed.

S&F in repair IInd class HW Plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 30mm flush shutters, solid core construction, with block board core and plywood face panells, commercial types on both sides incl teak wood beading alround the shutters complete all as specified and directed.

S&F 2nd class hard wood 30mm thick made glazed and skeleton shutters factory made open rebated and prepared to recieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed.

M&L factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottam rail . paneling of plain colour PVC sheets to be filted in MS frame welded, sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with the solvent cement complete all as specified and directed.

S&F in opening solid PVC door frame of size 50mm x 47mm made out 5mm plain colour PVC sheets re-inforced with MS square tube complete all as specified and directed.

S & F in repair 30mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); fitted to chowkats , windows, ventilators etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.20 (b) complete all as specified and directed.

Dismantling of boarding of any description and in any position complete all as specified and directed.

S&F 6mm thick in 5 layer Plywood, grade BWR,type BB, fixed withscrews to timber frame work etc,as in use false ceiling & incl beading size 40mm wide, for making to joint free false ceiling, complete all as specified and directed.

Dismantling timber scantlings in any position in fillets, rails, posts, rafters , purlins, etc. under 40 sq. cm in section (Unframed work) complete all as specified .

M&L for plain fillets, square, rectangular or triangular in section, and secured with nails or brads, using IInd class hard-wood clean sawn in sectional area exc 13 sq.cm and not exc 25 sq.cm complete all as specified and directed.

S&F in repair galvanized mild steel wire cloth 0.56mm fixed nominal dai of wire and avrg widh of aperature 1.18mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

S&F in repair 3mm thick Sheet glass, ordinaly quality and glazing with oil putty or secured with wdn beads as required in square n exc 0.5 sqm in each pane, complete all as specified and directed.

S&F in repair 4mm thick figured glass, pin head type quality and glazing with oil putty or secured with wdn beads as required in square n exc 0.5 sqm in each pane, complete all as specified and directed.

M&L for 50mm thick plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and incl use and waste of necessary form work complete all as specified and directed.

S & F Mild steel butt hinges medium weight , clod rolled, 100mm, ISI marked, complete all as specified and directed.

S & F Mild steel butt hinges medium weight , clod rolled, 50mm, ISI marked, complete all as specified and directed.

S&F 2nd class hard wood hollock small fittings such as brackets of any type, latch and hinge blocks, door stops and window stops, the like incl all necessary labours articles n. exc 200 cucm each complete all as specified and directed.

S & F 200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified

S & F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 150mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F 125mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F in repair of 300mm mild steel ordinary rate tail rod pattern door spring incl roller and roller plate complete all as specified and directed.

S&F in repair 20mm dia mild steel chromium plated curtain rails fixed with brackets, stops, rollers, etc. complete all as specified and directed.

Taking up or down 15 mm dia steel tubing incl connection and removal from site, complete all as specified and directed.

Taking up or down 20 mm dia steel tubing incl connection and removal from site, complete all as specified and directed.

S & F GI tubing medium gde with all fittings fixed to walls or laid in floors 15mm bore(concealed& open) complete all as specified and directed.

S & F GI tubing medium gde with all fittings fixed to walls or laid in floors 20mm bore (concealed&open) complete all as specified and directed.

S & F in repair 15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm bore CP fancy type (wall mixer & WBH mixer for mixing hot & cold water cast copper alloy with capstan handle, screwed down for iron pipe and fixed on wall , WHB, complete all as specified and directed.

S&F in repair stop valve/Angle cock/concealed fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type complete all as specified and directed.

S & F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Dismantling water tanks exc 500 n. exc 1000 ltr capacity complete all as specified and directed.

S & F 1000 ltr capacity rotational moulded polythene water storage tanks (clyndrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part I, complete all as specified and directed.

S & F 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified and directed.

S & F viterious china squatting span ORISSA Pattern size 580x440mm with integral foot rests, (excl flushing cistern and flush pipe) but with and incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete incl provn of lime concrete and making good to floor, in repair complete all as specified and directed,

S&F in repair 10 Ltrs capacity virgin polypropylene cistern, syphonic action type, ISI marked, white at low level complete with PVC bends, flush pipe and making all connections with and incl inlets ball valve float, handle, brackets and making good the disturbed sufaces in CM 1:3 to match with the existing surface, complete all as specified and directed.

S&F in repair Vitreous china wash hand basin white flat back or angle back type size 600mm x 480 mm white incl C P pillar taps 15mm bore waste chain & plug , waste pipe and prop stopper but incl cutting for and pinning in ends of brackets or erecting stand fixed, complete all as specified and directed.

S&F in repair vitreous china urinal, half stall type, of size 600 x 355 x 265mm, white (excluding flushing cistern, flush pipe), but including waste pipe fixed, complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, complete all as specified and directed.

S&F in repair soap dish chromium plated of size 180x160x90mm any type, fixed complete all as specified and directed.o plugs with chromium plated brass screws complete all as specified and directed.

S & F in repair brass chromium plated tabular towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains,incl fair finished & necessary formwork complete all as specified and directed.

M&L for mild Steel works as in bends straps, hold fasts etc, conforming to Fe-290 Gde-E-165, embedded portion duly painted with bituminious paint and sanded, complete all as specified and directed.

S & F 150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt, complete all as specified and directed.

Dismantling of Cast Iron pipe 75mm to 100mm dia complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) bends with oval accesse door with rubber ring joints fixed as required complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with SS grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) junction double, (double T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified and directed.

S&F 75mm dia PVC (SWR) junction double, (double T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified and directed.

S&F 75mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified and directed.

S&F 110mm dia PVC (SWR) "P" trap single, equal or un equal of any length including jointing with solvant cement as required complete all as specified and directed.

M&L for preparation of new or previourly untreated surface of wood or board materials of any description not otherwise described over 10cm in or girth & appyling two coats of synthetic enamal paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface of any descreption not otherwise described over 10 cm width or girth & appling two coats of sytnetic paint complete all as spd .

M&L for preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces including preparation of surfaces and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of plastered or unplastered old decorated surfaces of walls incl cornices, chajjas, sun shades etc. and applying one coat of cement base paint (1st quality) with and incl curing the surfaces and curing the same after application of cement base paint (tint as approved by GE) including complete removal of existing surface with sand paper or iron patti/ flat complete all as specified and directed.

M&L for preparation of old decorated plastered / unplastered surfaces of ceiling one coat of white wash on ceiling and AC plain building board surfaces as in ceiling complete all as specified and directed

M&L for preparation of newly decorated plastered / unplastered surfaces of ceiling one coat of white wash on ceiling and AC plain building board surfaces as in ceiling complete all as specified and directed

Complete removal of existing old surfaces applying two coats of oil bound distemper over one coat of wall putty(2mm) on walls complete all as specified and directed.

M&L for preparation of Newly plastered surfaces of walls incl cornices, chajjas, sun shades etc. and applying two coat of cement base paint (1st quality) with and incl curing the surfaces and curing the same after application of cement base paint (tint as approved by GE) over one coat of primer, complete all as specified and directed.

M&L for two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface incl 1mm thick wallcare putty, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any guage thickness incl Nainital pattern as in roof covering complete all as specified and directed.

S&F for Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, facia, flashing, eaves board, valley gutter etc, fixed all as per manufactures's instructions, fixed with self tapping screws at site with suitable arangement as required, complete all as specified and directed..

S&F in repair for 75mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate , as in filling of mass concrete for sub base floors complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded and pointed in any mortar, complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid & dado and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete over and including 15 mm thick screed bed or bedding with CM 1:6 ,etc complete all as specified and directed. Note:- (i) The rate of kota stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achieve the desired granite finish all as spfd.

Machine cut kota stone slab 20-25mm thick in riser steps,skirting,dado , nosing and pillar over 10mm thick cement screed base laid with CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing,etc complete all as specified and directed. Note:- (i) The rate of kota stone shall be deemed to incl for full rounded off corner/ edges/nosing incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achieve the desired finish all as spfd.

Roughening surface of old concrete by picking,sweeping clean and washing down eith water to remove dust and brushing neat cement slurry with 3.0 kg of cement per sqm. complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position (Unframed work) complete all as specified and directed.

S & F second class hard-wood, timber fixed and clean sawn, in scantlings or post complete all as specified and directed.

All as per serial item No 96.00 above but except timber, complete all as specified and directed.

Supply only water proofing compouond all as specified as per manafature instruction, complete all as specified and directed.

M&L for coloured chequred cement conc tiles (30cmx30cmx22mm thick) in grey cement and with pigment in floors etc, set and jointed in neat cement slurry, over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F mild steel framed work as in grills,guard bars etc. with ends of bars shouldered/welded and/or riveted and other simillar works confirming to Fe410-0 or Fe310-0 complete all as specified and directed.

Chipping of unsound /weak concrete materials from slabs , beams,columns ,lintel,chajja, fin , facia etc. including tapering all edges, making square shoulders of cavities air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting incl foreign matrials, loose concrete/ aggregate etc and disposal of all debris out of MOD land (upto 4 storey of building) for 25mm average thickness for slabs/Chajja, complete all as specified and directed.

Removing of concrete all around reinforcement including from behind the reinforcing bars to give an average 25mm (but not less than 15mm clear air gap) by manual methods (using wire brushing ,chiselling etc) and applying alkaline rust removing chemical followed by removing rust including from behind the reinforcing bars by emery paper and cleaning the area throughly by water and allow it to dry all as per manufacturer's instruction to give it a totally rust free finished steel surface upto 12 mm dia bar ( upto 3 storey of building), complete all as specified and directed. Make : SIKA/ FOSROC or equivalent as approved.

M&L for providing single coat of epoxy bond adhesive of prepared non metallic surface (existing surface) and applying by brush all as per manufactures instruction/specification. The bonding agent shall have minimum compressive strength of 40 N/Sqmm and upto 3 storey, complete all as specified and directed.

Supply and application of Epoxy Zinc rich primer on the prepared steel surface by brush the primer shall have a minimium specific gravity 1.75 minimum weight film thickness/coat 40 microns and minimum adhesive bond strength with steel is 1.5N/mm2 upto 3storey High, complete all as specified and directed.

M&L for introducing new reinforcement bars for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling,fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc upto 12 mm dia bar upto 3 storey High, complete all as specified and directed.

Removing demolished/excavated material /soil .n exc 50m,or out side station depositing were directed at a level n.exc 1.5m above the starting point , complete all as specified and directed.

M&L for stone walling of random rubble stone masonary, uncoursed, well bounded, bedded & solidely hearted built in cement mortar (1:6) using locally available best stone complete all as specified and directed

M&L for rendering 20mm thick on stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6,incl chiken mess, finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S&F structural steel work as in roof trusses (framed), trussed, purlins crane gantries, rails & fastenings & heavy bracketsframing (beam, tee, angle, gusset plate, channel or flat section including distance pieces, cleats etc, structural steel confirming to Fe-410w, Gde-250, quality- 'A', complete all as specified and directed.

S&F Mild steel plain black sheet 2mm thick in hearths, covering to door shutter, ducts, etc. cut to size, edges beaded if directed, holes punched, including round headed screws, clout nails or rivets, fixed to wood or steel members with plain 40mm lap joints or welded/ riveted seams including bending,turning up, mitred angles, stopped ends, etc as required, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and smooth without using extra cement, with and incl use and waste of necessary form work complete all as specified and directed.

S & F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board, valley gutter etc, fixed all as per manufactures's instructions, fixed with self tapping screws at site with suitable arangement as required, complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment set over sand cushioning, complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in flooring finished even and smooth surface complete all as specified and directed.

S&F fibre reinforced translucent corrugated sheeting, 2mm thick with two corrugation side lap fixed with coach screws and washers, in roofs, wall etc complete all as specified and directed.

S&F 5 mm thick plain poly carbonate translucent sheeting fixed with self tapping screw incl dismantling complete all as specified and directed .

M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains incl fair finises & necessary formwork, complete all as specified and as directed.

S&F hand rails, half round or other steel section or core for wooden hand-rail straight portion,drilled and countersunk for balusters, running bars, for ornamental and intricate design for doors, gate, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, nut & bolt, slding door bolt, slider wheel etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for rubber moulded pre polished lacquer finish chequered cement concrete tiles 300 x 300 x 25mm thick, with grey cement and pigment set, jointed and pointed in neat cement slurry in floors over Screed bed or bedding layer of mortar as in 1:6 15 mm thick for laying floor finishes, complete all as specified and directed.

Taking down carefully aluminium point wiring (light, Fan, Socket or power) complete including fittings and fixtures such as switches, ceiling roses pendants, regulators, sockets light fitting etc removing materials to store for keeping in safe custody or for taking credit including making good the disturbed portion/surface complete all as specified and directed.

M&L for point wiring with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed size 1.5 sqmm with concealed Conduit PVC medium grade not less than 20mm dia with fixing accessories, to be fixed , for one light /fan/bell point controlled by one switch with pressed steel concealed terminal boxes covered with 3mm thick laminated sheet incl. continuous earth wire of PVC insulated unsheathed multi stranded copper conductor cable size 1.5 Sqmm for earth wire connected to common earth dolly complete all as specified and directed.

All as per Srl item No 123.00 above but for one 3/5 pin socket 5 Amp on same board, with 1.5 sqmm wire with 1.5 sqmm earth wire complete all as specified and directed.

All as per Srl item No 123.00 above but for one 3/5 pin socket 5 Amp on independent board with 1.5 sqmm wire with 1.5 sqmm earth wire complete all as specified and directed.

All as per Srl item No 123.00 above but for 3 pins socket outlet 15 Amps independent with 2.5 sqmm incl continuous earthing with multistandard copper conductor PVC insulated unsheathed size 2.5 Sqmm complete all as specified and directed.

S&F switch piano flush type/ Bell push, 5 Amps, single pole one way complete all as specified and directed.

S&F socket 3/5 pins, 5/6 Amp, flush type piano (multi purpose) complete all as specified and directed.

S&F Socket 15 Amps flush type,3/ 6 Pin, 230 Volts , AC complete all as specified and directed.

S&F switch 15 Amps flush type 230 Volts , AC complete all as specified and directed.

S&F ceiling rose, PVC/ polycarbonate isolated body of size, 65x20mm, three terminals complete all as specified and directed

S&F lamp holder PVC body with back plate complete with 9 Watt lamp warm type complete all as specified and directed .

S&F VTPN prewired distribution board TPN-DPX 100 MCCB including one No MCCB 100 Amps as incomer and suitable SPN/TP MCBs as outgoing double door type sheet metal enclosure 415V with 200 Amps rated standard busbar of suitable size plate and common neutral link without MCBs with blank plate suitable for 4 way complete and including taking down all as specified and as directed. Note :- MCB/SP/TP shall be measured in respective items.

S&F SP&N sheet steel powder coated Distribution board for MCBs fitted with bus bar, Neutral link, earth bar and din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 12 ways complete including taking down complete all as specified and directed.

S&F MCB SPN 32 to 40 amp rating 240V, 10KA, B-Curve incl all terminals and fittings etc., complete all as specified and directed.

S&F MCB SP 6-32 amp rating 240V, 10KA, B-Curve incl all terminals and fittings etc., complete all as specified and directed.

M&L for earthing complete with galvanized steel plate earth electrode 60cmx60cmx6mm thick surrounded by char coal and salt buried directly in ground vertically in pit of depth not less then 2.25 mtr below ground level with top edge of the earth plate at depth of not less then 1.5 mtr below ground level surrounded from all sides by char coal dust and common salt in alternate layers of 15 cm depth and earth plate electrode connected to galvanized earth lead wire of 4.0mm dia at two points by means of GI nuts bolts, check nuts and washers and connected to earthling test point drawn through GI pipe for protection of earth lead wire incl PCC earth pit 1:3:6, type C-2, with CI frame and RCC cover all as shown in electrical Plate No 3 on SSR Part-I including testing and dismantling, taking down old unserviceable earthing complete all as specified and directed. Note: (I) Rate of Earth work, Earthing electrode, all connections, nut-bolts, washers, complete labour, testing, Earth lead upto 7.5 mtr, char coal dust, common salt, porcelain insulator, PCC earth Pit, CI frame, RCC cover, funnel with wire mesh are incl in quoted rate and watering pipe, earth lead protection pipe, test poit, earth lead exceeding 7.5 mt are measured and paid separately.

M&L for sub main wiring with two runs of single core 6 Sqmm (nominal area) PVC insulated and unsheathed multi stranded copper conductor cable LT 1100 grade FRLS-H cable drawn and PVC rigid conduit 20 mm dia with all necessary fittings and accessories and one run of PVC insulated and unsheathed single core cable with copper conductor of size 6 Sqmm as earth wire (green in colour ) run through PVC rigid conduit and connected to common earth dolly , including taking out the old sub main wiring complete all as specified and directed. Note. Two run of cable and one run of PVC conduit and one run of earth continuity wire shall be measured as one run complete all as specified and directed

S&F LED Bulkhead luminaire 10W Decorative type as per sample complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings complete all as specifed and directed. Make: Polycab Cat ref 60 BHE 10W 60, CROMPTON CAT REF LBHP-10-CDL/ BAJAJ CAT BIBWP 10W LED .

S & F LED tube light along with fixture, 18/20W (4 feet) wall mounted LED batten, extruded PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffused, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings complete all as specified and directed. Make: Polycab Cat ref INTENSO LXS LED BATTEN 4 FEET 18 W/ CROMPTON CAT REF LCTL-18-CDL/ BAJAJ CAT BCLSB 18 WH .

S&F in replacement of Wall Lamp/ Wall light 10 Watt decorative for bedroom, living room and all home decor vintage surface mounted classic sconce with new styles antique lamp shades branded LED bulb with e27 holder, complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Metal clad ingle pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20 Amp, 240V, complete all as specified and directed.

M&L for Fresh Air Fan made of PVC body 250 mm sweep 1200 RPM, 230V including fixing arrangement complete with louver sutters and making opening in wall of suitable size incl making good to the surface of wall complete all as specifed and directed. Note:- Old U/s fan to be deposited in E/M store yard.

S&F LED building secuity light 25 watt, fixed on existing bracket with all connected accessories complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings all as specified and directed.

S&F Air termination, single pointed aluminium rod 12mm dia and 300mm long, complete all as specified and directed.

S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw, complete all as specified and directed.

Supply and laying Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground, complete all as specified and directed.

Supply and laying Galvanised iron strip 32 x 6 mm buried in ground with saddles and fixing screws etc.buried in ground, complete all as specified and directed.

Supply, Fixing & laying GI tubing light grade 40 mm dia used as protection pipe for earth lead strip in earthing or alongwith pole/ wall/ culvert/ drainge etc for mechanical protection of cable, complete all as specified and directed. Note: All required items and acessories, bend, joints, nut and bolts, clamps etc are incl in quoted rates.

S&F of sheet metal enclosure for MCB DB TPN double door, 4 way complete with 200 Amps rated Bus bar, complete all as specified and directed.

S&F sheet metal enclosures for MCB distribution board SPN 8 way double door type with 200 amp rated bus bar and suitable for SPN Isolator as incomer, complete all as specified and directed.

S&F MCB TPN 40Amps 415V incl all termnials, fitting etc incl taking down complete all as specified and directed.

S&F RCBO for earth leakage , over load & short circuit protection 2 pole, 40 Amp rating, 100mA capacity suitable for 240 Volts, complete all as specified and directed.

M&L for exhaust fan heavy duty, MS body, 450 mm sweep, 1200 RPM including fixing arrangement with fastner, nut , bolt, washers etc complete with louver shutters and making opening in wall of suitable size including making good to the disturbed surface of wall, incl taking down of old unsv exhaust fan, complete all as specified and directed. Note: Old U/s fan to be deposited in E/M Yard.

NSK TRADER