Replacement of over aged signalling installation at Caranzol, Dudhasagar and Sonalim stations of Hubballi Division.

A1-Schedule A1: Purely Execution (Non SOR)

B1-Schedule B1: Purely Supply(Non SOR)

C1-Schedule C1: Supply & Installation (Non SOR)

E1-Schedule E1: Electronic Interlocking

F1-Schedule F1: Block, HASSDAC, MSDAC

G1-Schedule G1: Fire Alarm System

H1-Schedule H1: Telecom Non- SOR

Item Breakup - A1-Schedule A1: Purely Execution (Non SOR)

Laying / drawing of various type of cables Metre on PVC pipe / capping casing, or cable trays, ladder, shelter etc as instructed by Railway engineer at site. (Indoor cables to be drawn through pipe, outdoor cables if required to be clamped on wall/Floor etc)

Provision of Lighting arrangement for NI Set working at both side Goomty and Point locations.

Erection o f C T R a c k w i t h scaffolding Numbers suitably concreting tri-pod bases and reel insulators with "J" bolts and nuts. Tripod and other supportings are to be painted in 2 coats with enamel.

Cable terminals fuses, L D s e t c meggering the Conductor cables and recording the readings.

Earthing and soldering of the cable Per Unit armours. (Per Unit = Per Cable)

Strengthening of foundations of Signals, Numbers full/ half location boxes, by carrying out the earth work around the foundation, ramming of the earth carrying out masonry work from bottom of earth work using country stones and cement masonry to prevent the earth from sliping down the bank. As per technical specification. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Trenching under rails for crossing the Metre track (Track crossing) and refilling of trenches as per RDSO drawing no SDO/Cable laying /009. The track crossing shall be done at right angles. The depth of cable trench shall be 1.2Mtrs below the rail flange. The depth between top cable and the level of rail flange of the rail shall never be less than 1.0Mtr. The ballast shall be stored seprately. While making the trench and the earth soil has to be filled first to the ground level and the ballast has to be properly put in the track. this work has to be done under supervision of supervisor of S&T and supervisor of P.Way.

Hiring of Vehicle for execution of the Year Project.

Excavation of square coil pit upto a depth Numbers of 1 Mtr.x 1.5 Mtr for providing coil at locations box,point,signals etc This includes back filling and ramming of trench/pit after laying the cable and consolidation of soil.

Laying of PLB HDPE duct, 40/33 mm Dia, Metre in the trenches and in the protective works already provided including in HDD portion and supply pulling of Nylone rope through it at different places as per direction of engineering charge or site engineer.

Testing a n d commissioning t h e entire Station signalling installations jointly with the Railway representative at site at the stations/ LC gates covered under various schedules of the Contract, a n d ensuring that all the signalling gears are installed and adjusted as per theexisting rules. The work also involves supply of required number of bound registers with good quality papers with all updated details of cable meggering, relays, batteries, block joints, route cancellation, relay room key e n t r i e s , b l o c k instrument k e y , earth resistance etc., and handing over to Railways.(Supply of 'As mades' is not covered in this schedule).Testing and commissioning of stations (upto 5 roads).

Testing a n d commissioning t h e entire Station signalling installations jointly with the Railway representative at site at the stations/ LC gates covered under various schedules of the Contract, a n d ensuring that all the signalling gears are installed and adjusted as per theexisting rules. The work also involves supply of required number of bound registers with good quality papers with all updated details of cable meggering, relays, batteries, block joints, route cancellation, relay room key e n t r i e s , b l o c k instrument k e y , earth resistance etc., and handing over to Railways.(Supply of 'As mades' is not covered in this schedule).Testing and commissioning of stations (above 5 roads). UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Releasing of existing control equipments Set - complete including way station equipments, telephones, p o w e r supply f o r w a y s t a t i o n e q u i p m e n t and t e l e p h o n e s , a l o n g w i t h all wiring, accounting and stacking them neatly at a p l a c e a s i n s t r u c t e d b y Railway representative at site.

Blowing/Drawing of OFC cable/Power Kilometre cable/Signalling cable inside permanently solid lubricated HDPE Pipe already laid. This work includes necessary duct integrity test for solid lubricated HDPE pipe. ( This includes Transportation of materials from nominated stores to site).

Engaging mechanical excavators like JCB Hour o r other machineries f o r regarding and levelling t h e formation, dismantling any i n f r i n g i n g s t r u c t u r e s , c l e a r i n g and removing debris etc., with all leads and lifts etc. complete and as per the instruction of Railway representative at site.

Installation of Unit Maintenance Free Set Earth Pit as per RDSO specification No.RDSO/SPN/197 Ver.1.0 or latest and as per Technical Specification.

Installation, Testing/ commissioning of Numbers Earth Leakage Detector 12 channel.

Provision of GI pipes (50/100/150mm dia) Metre for cable laying with offset at both ends and with couplings over RCC Bridges/ Drainage/ Culverts with concrete masonry supports of size 300mm x 300 mm x 300 mm at an interval of 2m.The ends of the pipes shall be closed with brick masonry abutments work so that no cable is exposed, the work shall be carried out as per the instructions of Railway representative at site (Supply of GI pipes with couplings and laying of cables is not included in this schedule). [Stone jelly of size 20/25mm, bricks, sand, cement and all other miscellaneous materials required for the work shall be supplied by the Contractor].

Provision of GI pipes-(50/100/150mm dia) Metre for cable laying with offset at both ends and with couplings over girder bridges by fixing on suitable MS Clamps at an interval of 2 Mtrs. The ends of the pipes shall be closed with brick masonry abutments work so that no cable is exposed, The work shall be carried out as per the instructions of Railway representative at site. (Supply of GI pipes with couplings and laying of cables is not included in this schedule).[MS angles, flats, bolts and nuts for manufacturing fixing clamps, bricks, river sand , cement and all other miscellaneous required for the work shall be supplied by the Contractor].

Laying Telecommunication cables a s p e r cable pla n i n cable trenches, masonry ducts, RCC Pipes, DWC pipes, GI Pipes etc. ( Supply of cables is not included in this schedules) UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Digging of cable trench to a depth of not Metre less than 30CMs in rocky terrain, concreting the trench with 150mm thick concrete with 1 cement, 2 sand, 4 grade stone 20mm nominal size. (All the materials is to be supplied by the contractor).

Excavation of pit, casting concrete Numbers foundation as per Drg.No.SG/SWR/052 using metallic templates, for erection of colour light signals up to 4 aspects. [Foundation bolts, cement, river sand, stone jelly of size 20/25mm dia and all other miscellaneous materials required for the work shall be supplied by the Contractor].

Erection of surface base, signal pole, Numbers mounting of colour light signal up to 4 aspects complete on Signal pole/ Off-set bracket, (for LED/ filament bulbs) with lenses, triple pole lamp holder, filament switching units, CLS transformer, current regulators (whichever is applicable), fixing of ladder with platform complete and concreting of ladder shoe, fixing of number plates, marker board, lens guard, fixing of speed limit board wherever necessary, termination of tail cables, wiring of signal unit with PVC wire 3/0.75mm copper, provision of EWS locks, and painting of one coat of red oxide and two coats of aluminium/ enamel paints. When the aspect is fixed on Offset bracket using 'U' bolts and nuts, a through bolt shall be provided by drilling a hole in the signal pole to prevent the offset bracket from sliding down. (Supply of surface base, Offset bracket, CLS pole, CLS aspects complete, ladder with shoes and platform, Speed limit board, LED aspects, current regulators, lamp holders, lamps, filament switching unit and CLS transformer is not covered in this schedule). ['U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm dia, river sand, Signal CollarRings, wire PVC 3/0.75mm copper, lens-guard, all fixing bolts and nuts, lead wool, paints PVC/Nylon sleeves, enameled number plates. enameled marker boards, EWS locks, and all other miscellaneous materials for the work shall be supplied by the Contractor].

Track Crossing by Horizontal Boring Metre method . This also includes insersion of HDPE duct (pipe) of 110mm dia in the bore drilled. ( Supply of HDPE duct (pipe)is not included). UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Carrying out Alterations to the existing Per Relay relays in the relay racks/apparatus cases as per the approved circuit diagram using wire PVC 16/0.2mm copper. The work includes painting alterations and releasing the unwanted wires carefully without disturbing the existing wiring. [Wire PVC 16/0.2mm copper, soldering materials, bunching threads, condensers, resistances and teakwood plank for fixing them and all other miscellaneous materials required for the work shall be supplied by the Contractor].

Provision of signaling arrangement Station during Non-Interlocked working of Signals and Points, such aserection and wiring of temporary r e l a y r a c k s and wiring of relay s, S M ' s s l i d e instruments, wiring alterations in the cable termination rack, apparatus cases, signals, Control panel etc , a s p e r t h e instructions o f Railway representative a t site. (Supply of relay rack, relays, a n d S M slide instrument is not included in this schedule). [All other miscellaneous materials required for the work shall be supplied by the Contractor].

Provision of PA system and Magneto Per Unit telephone communication at stations/ tents as p e r t h e instructions o f Railway representative at site. The PA system and magneto telephones will b e returned to the contractor after the completion o f NI working. Signalling cables available may be used for the communication. (Hiring of P A system equipments and magneto t e l e p h o n e s s h a l l be done by the Contractor) [All o t h e r miscellaneous materials required for the work shall be supplied by the Contractor]. (Per unit= per Tent per day)

Hiring of tarpaulin tents and providing Per Unit the same at places as instructed by R a i l w a y representative at site. The spacing inside the tent shall be app 8ft x 8 ft. Each t e n t shall b e provided w i t h a table, chair, tube lights and pedestal fan. Drinking water in cans. The tents shall be fixed firmly to withstand rain, strong wind etc.(Per unit= per Tent per day)

" Fi x i n g o f E K T instrument w i t h (or) Numbers w i t h o u t c r a n k h a n d l e o r o n suitable fi x t u r e s at station/apparatus case, provision of economiser push switch with locking facility, wiring with wire PVC 16/0.2mm copper, provision of teakwood terminal box covered with decolum along with locking facility and painting. (Supply o f electric k e y transmitter and crank handles is not covered in this schedule). [wire PVC 16/0.2mm copper, wire wound resistance, decolum covered terminal box with locking facility by using 25mm thick teakwood, bolts a n d nuts, paints, push s w i t c h e s , p a d l o c k s a n d other miscellaneous materials required for this w o r k s h a l l be supplied by the contractor]." UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Releasing o f existing apparatus cases Numbers (Full/ Half/Quarter size) without damage after releasing the shelf planks, Terminal blocks, Fuse Blocks, Terminal Boards, Relays of all types EKTs, Secondary Cells, power equipments, 'E' type locks, etc., and breaking the concrete foundation. After releasing, t h e resultant pits a r e to b e closed and consolidated b y ramming and levelling. The released materials shall b e accounted and stacked at a place as instructed by Railway representative at site.

Breaking of concrete and releasing the Numbers existing cable termination boxes, after releasing the b a s e p l a n k , Terminal blocks, Fuse Blocks, Terminal Boards, cut rails, pipes, etc., closing the resultant pits and consolidating it by ramming and levelling. The released materials shall be accounted and stacked neatly at a place a s instructed b y Railway representative at site.

Releasing o f existing Block Instruments Numbers ( a l l t y p e s ) , B l o c k counters, batteries, block filter, block b e l l equipment etc., c a r e f u l l y w i t h o u t a n y damage, accounting and stacking them neatly at a place as instructed by Railway representative at site.

Re l e a s i n g o f a l l p o w e r equipments Set including equipment s t a n d s , terminal boards, power panel etc., i n t h e power r o o m c a r e f u lly w i t h o u t c a u s i n g any d a m a g e t o the equipments after disconnecting all the supply wires. The released equipments shall be accounted and stacked at a place as instructed by Railway representative at site. After releasing any holes i n the walls/ flooring shall b e filled w ith cement mortar and plastered.

Excavation o f p i t i n a n d a r o u n d the Numbers existing location b o x e s v e r y carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringement as instructed b y the Railway representative a t site. T h e w ork includes ensuring the safety of the signaling system, releasing the cable coils to give access for shifting/turning t h e l o c a t i o n boxes. Necessary masonry work and earth work i n and around the location boxes t o the required level shall be done as instructed b y the Railway representative a t site. If t h e existing earth connections to the location boxes are disturbed, the earth wires shall be properly re-connected.[All materials required for the work shall be supplied by the Contractor]. Shifting of apparatus case (full) UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Excavation o f p i t i n a n d a r o u n d the Numbers existing location b o x e s v e r y carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringement as instructed b y the Railway representative a t site. T h e w ork includes ensuring the safety of the signaling system, releasing the cable coils to give access for shifting/turning t h e l o c a t i o n boxes. Necessary masonry work and earth work i n and around the location boxes t o the required level shall be done as instructed b y the Railway representative a t site. If t h e existing earth connections to the location boxes are disturbed, the earth wires shall be properly re-connected. [All materials required for the work shall be supplied by the Contractor]. Shifting of apparatus case (half)

Releasing of Existing tail cables and Per Unit drawal of new tail cables for colour light signals up to 4 aspects with or without route indicator, post type shunt signal and Calling on signals, termination of new tail cables and wiring using wire PVC3/0.75mm copper. This work includes drawal of new tail cables into the signal post duly releasing the existing tail cables from the relevant signals and re- surfacing the earth excavated as instructed by Railway . (Per Unit = Per Cable)

Excavation of cable trench in all kinds of Metre soil except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.3 Mtrs. (Laying of cables is not included in this schedule).

Refilling of cable trench 1m depth by Metre 0.3m width through out, with earth after laying of cables, and consolidating the trench by ramming and leveling.

Excavation of cable trench in all kinds of Metre soil except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.5 Mtrs. (Laying of cables is not included in this schedule).

Refilling of cable trench 1m depth by Metre 0.5m width through out, with earth after laying of cables, and consolidating the trench by ramming and leveling.

"Transportation, Erection and wiring of Numbers IPS to power distribution panel. This includes transportation of IPS batteries from stores to the site, Erection of IPS panels on teakwood planks, interconnection between panels and wiring the IPS to power distribution panel using 10 sqmm multi-strand copper cable. The wiring should be done neatly using Aluminium ladder with Phynolic sheet (Aluminium ladder, Phynolic sheet of thickness 6 mm, teak wood plank of width 150 mm and thickness 25mm, 10 sqmm multi-strand copper cable and all other miscellaneous materials to be supplied by the contractor). UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Excavation of pit, casting concret Numbers foundation and erection of apparatus case full size as per Drg. No. SG/CN/02/06 and fixing of 2 nos of "E" type locks, one for the front door and another for the back door, fixing o f one hard wood shelf plank 37mm thick and painting the appratus case inside and outside with one coat of red oxide and two coats of aluminium paints, along with painting of terminationand equipment particulars on the doors of appratus cases instructed b y railway representative at site. ( Supply of appratus case is not included in this schedule). [ Foundation bolts & nuts, 'E' type locks, cement, river sand, stone jelly of size 20/25mm, hardwood plank of 37mm thick, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required for the work shall be supplied by the contractor].

Excavation of pit, casting concret Numbers foundation and erection of apparatus case half/quarter size as per Drg. No. SG/CN/02/07 and fixing of 2 nos of "E" type locks, one for the front d o o r and another for the back door, fixing o f one hard wood shelf plank 37mm thick and painting t h e appratus c a s e inside and outside with o n e coat o f red oxide and two coats of aluminium paints, along with painting o f terminationand equipment particulars on the doors of appratus cases instructed b y railway representative at site. ( Supply o f appratus c a s e i s not included i n this schedule). [ Foundation bolts & nuts, 'E' type locks, cement, river sand, stone jelly of size 20/25mm, hardwood plank o f 3 7 m m thick, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required for the work shall be supplied by the contractor].

Concreting o f cable laid i n the trench or RMT GI pipe/DWC/HDPE pipe in which cable is already laid to a size of 300*300mm with 1:3:6 mortar. (All the materials required for the work should be supplied by the contractor){Per Unit- RMT}.

Provision of One skilled and One Month unskilled staff round the clock to attend to teething trouble of the installation along with SSE/JE(Sig) after the installation has been brought into commissioning. The work includes routine maintenance, failure restoration as per the direction of the SSE/JE(Sig).

Arranging Stores/site for loading/unloading/stacking of departmental materials.

Transportation of Signalling materials by MT-Km road as per the instructions of Railway representative at site. The work also includes loading and unloading of the materials. Transportation more than 100 Kms.

Releasing of Diesel Generators in the Numbers existing room along with all other gadgets without causing any damages . UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Transportation of 10/15/20 KVA DG set, Per Trip including all lifts and leads (Lift arid lead shall be done using suitable Hydraulic crane/Fork Lift. The contractor will be responsible for the safe transshipment of the DG set without causing any damages during transportation). h Transport at of the DG set over a distance of 80 to 150kms.

Provision of DC Single/ Double rail track Numbers circuit in Point zone to suit RE/Non-RE areas as per approved signaling plan using Plug-in type track relays. This work includes provision of double bonding, and parallel jumpers, provision of bond wire clips, provision of track lead connections using 2c X 2.5 sq.mm cable, provision of TLD boxes 2 Nos. at Relay end, 2 Nos. at Feed end and 2 Nos for parallel jumpers as necessary to suit layouts, for each Track Circuit, and termination of jumpers and tail cables in track lead junction boxes, installation of relays, track feed battery chargers to charge up to 4 cells, track feed resistance, B type choke and secondary cells - 80 AH capacity in apparatus cases and wiring with wire PVC 3/0.75mm copper. The work also includes painting of track Circuit No. with Feed end/ Relay end details on the TLD boxes. The work also includes provision of insulations for gauge tie plates and nose crossing plates wherever required. (Provision of rail joint insulation is not covered in this schedule.) (Uninsulated gauge type plate and nose crossing plate will be supplied by Railways. Supply of track feed battery charger, B type choke, track relays, uncharged secondary cells (2V - 80AH), TLD boxes with stumps, 2cX2.5 sq.mm cable, is not covered in this schedule). [track feed resistance, Gauge tie plate and nose crossing plate insulations, PVC/Nylon bushes for TLD boxes, PVC sleeves, all types of fixing bolts and nuts with spring and flat washers, teakwood stand for fixing track feed resistance, GI bond wire 8 SWG, Channel bond pins, bond wire clips, paints and all other miscellaneous materials shall be supplied by the contractor. Secondary cells-80 AH capacity shall be charged by the contractor through reputed charging agencies]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Provision of DC Single/ Double rail track Numbers circuit in Other than Point zone to suit RE/Non-RE areas as per approved signaling plan using Plug-in type track relays. This work includes provision of double bonding, and parallel jumpers, provision of bond wire clips, provision of track lead connections using 2c X 2.5 sq.mm cable, provision of TLD boxes 2 Nos. at Relay end, 2 Nos. at Feed end and 2 Nos for parallel jumpers as necessary to suit layouts, for each Track Circuit, and termination of jumpers and tail cables in track lead junction boxes, installation of relays, track feed battery chargers to charge up to 4 cells, track feed resistance, B type choke and secondary cells - 80 AH capacity in apparatus cases and wiring with wire PVC 3/0.75mm copper. The work also includes painting of track Circuit No. with Feed end/ Relay end details on the TLD boxes. The work also includes provision of insulations for gauge tie plates and nose crossing plates wherever required. (Provision of rail joint insulation is not covered in this schedule.) (Uninsulated gauge type plate and nose crossing plate will be supplied by Railways. Supply of track feed battery charger, B type choke, track relays, uncharged secondary cells (2V - 80AH), TLD boxes with stumps, 2cX2.5 sq.mm cable, is not covered in this schedule). [track feed resistance, Gauge tie plate and nose crossing plate insulations, PVC/Nylon bushes for TLD boxes, PVC sleeves, all types of fixing bolts and nuts with spring and flat washers, teakwood stand for fixing track feed resistance, GI bond wire 8 SWG, Channel bond pins, bond wire clips, paints and all other miscellaneous materials shall be supplied by the contractor. Secondary cells-80 AH capacity shall be charged by the contractor through reputed charging agencies].

Supply of design set for circuit. ( SIP, Set TOC, RD etc). UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Preparation of Cable Route Plan, Cable Station Core Plan, Cable Termination Rack Particulars, Location Box Particulars, Power Supply Diagram, Track Circuit Bonding Diagram and/or any other drawing on Auto- CAD in A2/A3/ A4, etc. size (as per instructions of Engineer in- charge). Initially Contractor shall submit 2 sets of'AS PLANNED' documents complete for approval of Railways. Oneset is returned either duly approved for making a fair copy or forre- submission for approval after incorporating the changes asrequired by railways. After preliminary approval, execution ofwork shall be carried out at site. After Completion of work, 2 sets of 'AS MADE' Check Prints are submitted for Administrative approval. Railways will return one set to the contractor duly approved with alterations/corrections if any. The contractor shall incorporate Railways alterations/corrections in the tracingswithout any deviation and submit all tracings complete in all respect along with its soft copies in USB Pen Drive and 6 sets of final completion drawings in properly bound booklets. [For Centralized Electronic Interlocking Stations/Small Stations]. Total 20954819.86

Item Breakup - B1-Schedule B1: Purely Supply(Non SOR)

Supply of Steel Almirah (Model : Godrej Numbers Store well/slimline 4S ). [inspection by Consignee].

Supply of terminal block 1 way PBT Numbers 60mm as per RDSO Drg. NO SA 23745/Alt.5 & IRS S75/91 & IRS S 23 with latest amendment. [inspection by RDSO].

Supply of DWC pipe of 315mm outer dia / Numbers 271 mm inner dia in lengths of 6 mtrs with coupler to IS specification no 14930 Part- II. The IS Spec shall be marked on the pipe. [inspection by RITES].

Supply maintenance console (Laptop) . [inspection by Consignee].

A3 Multifunction Laser colour printer with Numbers Automatic document feeder. Xerox Versalink C7020 + 2 trays with 2 years warranty or similar make. [inspection by Consignee].

Desktop PC with wireless keyboard and Numbers mouse for office use. [inspection by Consignee].

Supply of Resistors/ Condensers/ Diodes/ Numbers Electrolytic Condensors 470 mfd. [inspection by Consignee]

Supply 50V/1000/2000 mfd. [inspection by Consignee].

Supply 10W/100/150/500/2200. [inspection by Consignee]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of Diodes by [inspection by Consignee].

Supply of 2T VF Transformer Cylindrical Numbers type as per RDSO Specification no IRS:TC76/2021 OR latest.[inspection by Consignee].

Standard 19" Rack Mountable Multiplexer Set device consisting of four E1 interface, dual optical ports with dual core and Single core path 20 Kms driving distance. Multidirection supporting upto 5 direction either with optical or E1. Ethernet ports for camera connectivity. RS232 interface for RTU connectivity. E&M cards with 8*E&M ports with 2W/4W setting.FXO/FXS card support with 10*FXO/FXS ports. Total 4 hot swappable slots for field upgradable Multi service Modular cards. Device Management with Telent & NMS. Unit Support Audio Buzzer Alarm Interface. Potential Free contact. Dual DC with 18-72VDC range. Accessories - AC-DC adaptor, E1 & E&M cable.( Similar to Maple 4CS/FABIO. [Inspection by Consignee].

"Supply of E&M card suitable to be Numbers accomodated in maple 4C(O) Multiplexer with 8 channel 2W/4W configureable with one number of 50 pin SCSI connector cable. Firms offer make/model: MAPLE/ FABIO.[Inspection by Consignee]"

Supply maintenance Free (SMF) Batteries for 25W VHF radio Communication use. As per specification enclosed with 24 months warranty: Make: Panasonic, Exide, Amaron, Quanta or HBL. [Inspection by Consignee]

Supply of 19"-42U Rack complete with Numbers fittings for housing SDH equipment, FDMS, DDF and other equipment like cable managers, completely wired using krone module and other equipments like runawayladders etc., as per technicalspecification below. It should be ableto lock all the equipment with onlyorder wire telephone outside the rack, the rack should of APW President/Rittal make etc., The components ofthe rack are specified below. this includes transportation and installation of rack in prefab/building at specified stations. a. Rack S33 42U600WX600D-1 no. b.fixed side panels 42U x 600 D -2nos. c.Frontglass door plain 42U/600W -1 no. d.Rear MS DOOR PLAIN 42 U/600W-1no. e. Caster with brakes- 2nos.f. Fans directly mounted on the top48v Dc 90CFM -2NOS. g.Kronemounting bracket -01 No. h. MCBmounting panel with MCBS a)32Amps MCBs (DP) -2 nos. b) 6 AmpsMCBs (DP) -6 nos. i) earth continuity kit -01 nos j. Equipment trays- 5 nos.k. channel with cable loops 42U- 2NOS Rubber matt of 1mtr x 2 mtr. [inspection by Consignee]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of 6 Fiber Armored OFC Cable, Metre Single Mode OFC for laying over the Platform shed as per latestTEC/BSNL Specification. [inspection by Consignee].

"Supply of Permanently Lubricated High Metre Density Polyethylene Duct (PLB HDPE), 40/33 mm Dia, along with End Cap, End Plug, Cable Sealing Plug and Couplers, as per RDSO/SPN/TC/45/2013 Rev.2 (upto Amdt.2) or latest.[inspection by RITES]."

Supply of Calling on signal unit complete Numbers and U bolts to drawing No SA.24381/Adv. [[inspection by Consignee].

Supply of Universal locks ( EWS Locks) Numbers with one key for every ten locks. [inspection by Consignee].

Supply of Double walled corrugated pipe Metre - 103.5mm inner dia & 120mm outer dia conforming to specification No. IS 14930(Part 2): 2001 with one coupler for every 6m of pipe. [inspection by Consignee].

Supply o f 2 pin socket - 5 A with switch, Numbers fixing t h e same o n t h e hardwood plank available a n d extending t h e 110VAC using wire P V C 3/0.75mm copper, i n all the apparatus cases, as per the instructions of Railway representative at site. [2 pin socket - 5A with switch, wire P V C 3/0.75mm c o p p e r a n d a l l other miscellaneous materials required for the work shall be supplied by the Contractor]. [inspection by Consignee].

Supply of Guage Tie Plate Insulation. Set [inspection by Consignee].

Supply of Insulations for IRS point Set machine. [inspection by Consignee].

Supply of DWC Pipe of 180 mm outer dia Numbers 153mm inner dia in lengths of 6 mtrs with coupler to IS specification No 14930 Part -II. The IS Spec shall be marked on the pipe.[inspection by RITES].

Supply of GI pipes - 100mm dia-4.5mm Metre thick as per Technical specification. [inspection by RITES].

Supply of GI pipes - 150mm dia-4.8mm Metre thick as per Technical specification. [inspection by RITES].

Supply of Relay Non-AC immune, plug in Numbers type style QN1, DC neutral line, 24V,8F,8B contacts, front and back contacts metal to carbon with plug board retaining clip and connectors confirming to BRS 930, IRS-S34, IRSS23 (as applicable). The interlocking code for this unit shall be ABCDF (with ATC clips). [inspection by RDSO].

Supply of AC immune plug in type style Numbers QNA1 DC Neutrel line 24 V 8F/8 B contacts front and back contacts metal to carbon with plug board ,retaining clip and connectors to BRS :931A,IRS:S@58<44@ IRS:S:34 & IRS:S:23 (as applicable) the interlocking code for this shall be ABDGH. [inspection by RDSO]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of Relay Plug in type AC LED all Numbers aspects AC lamp proving relay unit with inbuilt current transformer type slow to release neutral line Relay with 4F/4B contacts metal to carbon, shall be suitable for working with 110V AC LED signal lamp proving rates at 15W conforming to RDSO spec. no. STS/E/Relay/AC lit LED Signal/09- 2002, Amendment- 1, BRS 941A, IRS:S-23 and IRS:S-34 (as applicable). [inspection by RDSO].

Supply of Relay AC Immune, Plug-in Numbers type, Style QBCA1 DC biased point contactor, 24V DC, 2F(HD)/2F4B contacts front contact (heavy duty) and back contact metal to carbon, complete with plug board, retaining clip & connectors. Confirming to BRS 943, IRS S 34 & IRS S 23 as applicable. Interlocking Pin Code BCEJK. [inspection by RDSO].

"Supply of AC immune Plug in type Style Numbers QTA2 DC Neutral track relay 9 Ohm, 2F/1B contact as per Spec. No. BRS:933A along with IRS :S-23,S@45"38@ IRS:S@45<40@As applicable) or Latest. [inspection by RDSO]."

Supply of AC immunized Relays, plug in Numbers type, style QNA1K, 6F/6B contacts. DC neutral line Relay, working voltage 24V DC 1000 ohms, metal to carbon with plug board, retaining clip and connectors as per RDSO Specification No. BRS:931A & STs/E/Relays/UEA/PI dtd 30.05.97 Annex II & IRS:S-23@44"38<44@ STR: SIQ 0420 Ver.1 or latest. The interlocking code for this relay shall be CDEKY. [inspection by RDSO].

Supply of QBAT track Relay, AC Numbers immunized, 2F-2B, contacts, 9 ohms. Complete with plug, board, retaining clip and connectors as per RDSO/SPN/84 Ver. 2.0. [inspection by RDSO].

"Supply of Relay,AC Immunised,Plug in Numbers type ,Style ""QSPA1, DC Neutral line ,slow to pickup, 24VDC,8F/4B Contacts front and back contacts metal to carbon, complete with plug board, retaining clip and connectors conforming to BRS:933A,IRS:S@45<44@IRS:S-34 and IRS:S-23 or latest[as applicable]. [inspection by RDSO]."

Supply of Relay, Plug-in Type, QL1, Numbers 11F.4B contacts, Magnetically latched, neutral line Relay, working voltage 24V DC, Metal to Carbon with Plug board, retaining clips and connectors as per RDSO Specification No. BRS 935 A,IRS:S

applicable. The interlocking code for this unit shall be ABDEG. [inspection by RDSO].

"Supply of ARA terminal block PBT 6 way Numbers 25mm center as per RDSO Drg No. SA 23756/Alt.3 & IRS S. 75/2006 with latest amendment. [inspection by RDSO]." UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of Electric key transmitter rotary Numbers type of required ward nos with necessary inspection as per specification / drawing/ description enclosed in this document. [inspection by RDSO].

Supply of Signal aspect - LED Signal Numbers Lighting Unit Red with current regulator, as per RDSO specification No. RDSO/SPN/199/2010 revision 1.1 or latest. [inspection by RDSO].

Supply of Signal aspect - LED Signal Numbers Lighting Unit Yellow with current regulator, as per RDSO specification No. RDSO/SPN/199/2010 revision 1.1 or latest. [inspection by RDSO]

"Supply of Signal aspect - LED Signal Numbers Lighting Unit Green with current regulator, as per RDSO specification No. RDSO/SPN/199/2010 revision 1.1 or latest. [inspection by RDSO].

Supply of Signal aspect -Calling On LED Numbers Signal Lighting Unit with current regulator, as per RDSO specification No. RDSO/SPN/153/2011 Rev 4.1 or latest. [inspection by RDSO].

"Supply of surface base to suit CLS signal Numbers pole 140mm dia with necessary inspection as per specification / drawing/ description enclosed in this document. [inspection by Consignee].

"Supply of FRP 2 aspect color light unit Numbers assembly as per RDSOSpec. No. RDSO/SPN/ 194/2006 Rev .2.0 or latest (Terminal box,mounting socket, hood, side flange and fixing bolt & nut, eye bolt, M12bolt-3 Nos. and Fixing bolt 08 Nos. [inspection by RITES].

Supply of color light signal pole 140mm Numbers dia, 4.6m/3.6m tall with necessary inspection as per specification/ drawing/ description enclosed in this document, Supply of color light signal pole (3.6m). [inspection by Consignee].

Supply of CLS ladder with Platform and Numbers Shoes to suit CLS ploe 3.6m, as per specification / drawing enclosed. [inspection by Consignee].

Supply of offset bracket large/ small Numbers made of cast iron with necessary inspection as per specification / drawing / description enclosed in this document. a) Supply of offset bracket large. [inspection by Consignee].

Supply of PVC insulated wire copper Per Unit conductor 16/0.20 mm Each coil length of 100 mts (50% Red and 50% Black) as per RDSO spec No. IRS.S 76/89 amendment 3 or latest. [inspection by RDSO]. (per Unit = per Coil)

Supply PVC wire coils of size 28/03 multi Numbers strand flexible Spec . IRS. S76/89. Excise Duty. Amendment, NO.2 or latest. Each coil of 100 mtrs, material should be from RDSO approved firms only. [inspection by RDSO]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of PVC insulated wire multi-strand Per Unit copper conductor 10 Sq.mm flexible Each coil length of 100 mts (50% Red and 50% Black) as per RDSO specification IRS.S 76/89 or latest. [inspection by RDSO]. (per Unit = per Coil)

N D Fuse holder with blocks. [inspection Numbers by Consignee].

Supply of Non-deteriorating type fuse Numbers links 2 Amps for Railway signalling, voltage 240 AC/DC to Specn. No. IRS S.78/92. [inspection by RDSO].

Supply of Non-deteriorating type Fuse Numbers links 6 Amps for Railway signalling, voltage 240 AC/DC to Specn. No. IRS S.78/92. [inspection by RDSO].

Supply of Non-deteriorating type Fuse Numbers links 16 Amps for Railway signalling, voltage 240 AC/DC to Specn. No. IRS S.78/92. [inspection by RDSO].

Cable termination racks size 880mm X 2 Numbers Meters made out of 50mmX50mmX6mm thick MS angle POWDER COATED with stainless steel nuts and bolts for fixing the racks with suitable holes for hylem sheet complete as per standard practice with tripod bases and reel insulators. Cable ladder of 400mmx2000mm be provided at both sides with angle size 40mmx4mmx5mm with supporting flat of size 25mmx5mm.

Supply of apparatus cases size Full as Numbers per specification/ drawing. [inspection by RITES].

Supply of apparatus cases size Half as Numbers per specification/ drawing. [inspection by Consignee].

Supply of E type locks of different wards Numbers as per requirement with key per E type lock to Drg. No. SA.3376IM/Latest and RDSO Specn. No. IRS. S.30 64.Rev.0. [inspection by Consignee].

Supply of 6 Lever 75 mm NAVTAL Locks Numbers with 3 Keys or more Godrej make or similar. [inspection by Consignee].

Supply of UL standard PPTC fuses Numbers complies to UL Themistor standard 1434 with rating - 2 Amps. [inspection by Consignee].

Supply support Revolving Chairs (Bravo high back and Cushioned) of Godrej or reputed firm for seating arrangement. [inspection by Consignee].

Supply of Office table with plywood plank Numbers with thickness of 4 8mm, teakwood beading with three draws of size 4' X 2' with heavy duty S type chair with hand rest. The above is of Godrej or similar make. [inspection by Consignee]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of Basic material to construct Unit Set maintenance free eath as per RDSO spec. No. RDSO/SPN/197 Ver.1.0 or latest. consisting of a) copper bonded steel electrode of 3.0m long, 17.0 mm dia with copper bonding thickness mini 250 micron and UL listed and marked--1 no. b)Earth enhancement compound of RDSO approved brand supplied in sealed bags of min 10 Kgs-03 No. c) Copper strip of 150X25x6mm to terminate earth rod-1 No. d) Copper strip of 300X25x6mm (MEEB)-1 No. e) Copper strip of 150X25x6mm (SEEB)-1 nos. [inspection by RDSO].

Supply of Earth Leakage detector 12 Numbers channel (4 Channels110V AC, 2 Channels- 110V DC, 6 Channels- 24V DC) as per RDSO Spec./256/ 2002 or latest with 6 digit counter. [inspection by RDSO].

Supply of High Density Polyethylene Metre Pipes (HDPE) of 110 mm Outer Dia, 10 mm Wall Thickness, along with one coupler for every 6 Meters as per specification No. IS 4984: 2016 with latest amendments and Material Grade:PE 80. [inspection by RITES].

Supply of Insulation Sets for Ground Numbers Connection, Made of Nylon for 220mm throw Point Machine as per Specification No. IRS.S.40/84 Amdt No.01 or latest. One Set consisting of :- a) Insulating Washer Drg. No.-S-8640 = 12 Nos. b) Insulating Washer Drg. No.- S- 8640/1=04 Nos. c) Insulating Washer Drg. No.-S-8640/2=02 Nos. d) Insulating Bush Drg. No.-S- 23199=06 Nos. e) Insulating Bush D7Drg. No.-S-3463=01 N o . f) Insulating Bush Drg. No.- S22179=02 Nos. g) Insulating Bush Drg. No.-S-8912=02 Nos. h) Insulating Plate Drg. No.-S- 3404=02 Nos. i) Insulating Bush Drg. No.-S-8813 = 04 Nos. [inspection by Consignee].

Supply of insulations for 'D' clamp switch Set extension bracket to suit to universal point machine as per drawing supplied by the Railways. (One set consists of 'D' clamp insulation 2 No. Nylon insulation bushes 4 No., Nylon insulation washers 8 No.). [inspection by Consignee].

Supply of track feed battery charger as Numbers per Technical specification enclosed. [inspection by RDSO].

Supply of Low maintenance stationary Numbers secondary cells 2V-80AH capacity as per IRS: S 88/2004 Version 1.0 or latest. [inspection by Consignee].

Supply resistance disk type 0 to 30 ohms as per Drg.No.SA.20161/06/M. [inspection by Consignee].

Supply of Channel bond pins single Numbers groove 7mm dia. [inspection by Consignee]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of Track lead junction box - FRP Numbers type with 4 terminals and stumps with necessary inspection as per specification/ drawing enclosed. [inspection by Consignee].

Supply of 10 pair annealed tinned copper Metre conductor PVC insulated colour coded twisted pair switch board telephone cables PVC sheathed with nylon rip size 0.5 mm of reputed make.[inspection by Consignee]

Supply of STP CAT- 6 Cable compliant Boxes with latest EIA/TIA-568-B-2-1 StandardforCAT 6 Cable 305 Meters Roll /Bundle.[inspection by Consignee] Total 29426589.20

Item Breakup - C1-Schedule C1: Supply & Installation (Non SOR)

Supply and fixing of PVC pipe of 25mm Metre size of IS standards on wall/floor etc All necessary items like screws/nails required to be supplied by contractor. [inspection by Consignee].

"Supply, commissioning of SMPS based Integrated Power Supply (IPS) upto 4 Lines in RE area confirming to RDSO Specification No. RDSO/SPN/165/2023 Ver. 4.0 Amdt. 1 or latest with STR No:- SIQ 0110 Ver. 3.0 or latest along with status monitoring panel as per Drawing No.B/SG/Proj/BNC/ IPS /PI-4L/RE/01 of dated 06-10-2021 enclosed as Annexure A and B. IPS should be supplied with (55+5@61<41@ Nos. of uncharged LMLA Secondary Cells 2V-200AH as one set for one IPS confirming to QA IRS:S-88/2004 Low Maintenance Lead Acid Stationary Secondry Cells For S&T Installations along with 16 Sqmm cable for each IPS set is (50 Mtrs Red + 50 Mtrs Black) = 100 Mtrs. SPECIAL CONDITIONS:- 1. The supplier shall take up installation , wiring, testing and commission with minimum one month prior notice period from R a ilw a y s . 2.All the required cables/ Miscellaneous items for commissioning shall be supplied as part of this tender. 3.Supply, installation, testing and commissioning of SPDs (class B&C) are covered in scope of this tender, Supply items shall be inspected by RDSO. [inspection by RDSO]." UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Fabrication, supply and erection of Numbers conventional Earth to Siqnallinq/Telecom equipments -Excavation of earth and No. 6652 providing earth pipe of size 50mm dia. 3.5mm thick 2.0 m. long G.I. pipe of heavy quality with masonry tub constructed around at earth locations as specified by site Engineer. Alternate layers of 30kgs-charcoal and 30kgs- common salt to be filled in the pit while closing. The pipe perforation etc., to be arried out as per drawing No. SK 10/10. The earth pipe to be connected to the function with cable as supplied by Railways. The reading should be painted on the masonry tub. The masonry tub of 300 mm x 300 mm x 300mm (along with Kundi) should be covered with cement slab.[inspection by Consignee]

Transporting and supply and installation Numbers of concrete (RCC) route indicators at intervals of 50 mtrs as per technical specification They should be of standard RCC with Letters"SWR Telecom cable" as per type of cable laid to drawing.In case of telecom quad cable joint locations it shall be painted with red colour.

Installation, commissioning of Diesel Generator Set 15 KVA, Single Phase, 240V, 1500 RPM, 50 Hz, 8 BHP (minimum) mounted with air cooled double cylinder diesel engine with acoustic enclosure complete silent type DG sets confirming to RDSO Specn.No.IRS:S-69/86 or latest (CPCB Noise & Emission Complaint) Kirloskar make engine/alternator. This also includes supply of standard AMF control panel, supply of 12V/80 AH battery set along with battery charger of suitable rating for charging the batteries to ensure self starting arrangement of DG sets. It also includes supply of start/stop buttons,volt/Ampere/Frequency meters and 63 AMP MCB. Note: DG set will be procured from OEM or authorized dealer of OEM's with the warranty certificate of minimum 1 year. All masonry work required for installation of DG set will be done by contractor under supervision/ instructions issued by site engineer incharge.

Supply and Installation Testing and Numbers Commissioning of Isolated DC-AC Inverter 1+1 HA input 48 V DC,Output:220V AC 1000VA or higher, with all required Protection Circuits. [inspection by Consignee].

Supply, installation, commissioning of Set capacity 48V/200Ah VRLA Battery bank incharged condition as per technical specification. [inspection by Consignee].

Supply and installation of SMPS based Numbers charger 230V AC 50Hz input and 48V DC/25 Amps output in (2+1 configuration) suitable for VRLA battery as per RDSO specs: RDSO/SPN/TL/23/1999 Ver.4 Amdt. 1 or latest.[inspection by RDSO]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply and installation of lightening & Numbers surge arrestors of class B & C suitable for single phase supply in TT network. [inspection by Consignee].

Supply and Fixing of PVC pipes concealed Metre type duly breaking concrete bed/wall levelling surface by using cement ,sand etc and drawing different types of cables through it ( all the required material for except cable should be arranged by the contractor) (Inspection Consignee).

Supply and installation of yard layout Numbers diagram board in the station master's room. The board shall be made of Phynolic synthetic industrial fibre base fine weave cotton fibre board (matt finish) 6mm thick size 1800mm X 1200mm with aluminium channel frame. T h e yard layout shall b e neatly painted a n d fi x e d a s instructed b y Railway representative a t s i t e . [ A l l materials required for the work shall be supplied by the Contractor]. [inspection by Consignee].

Manufacturing, Supply, painting and Numbers fixing of markers of G/P/C/A/IB Markers/Number plates with engineering grade reflective sticker on MS sheet with clamps asper drawings/as per site incharge. including all fixing materials. [inspection by Consignee].

Supply and provision of Rubber mat of Square not less than 6mm thick a n d w i t h an Foot insulation t o withstand 650VAC, o n the fl o o r o f r e l a y r o o m e t c a t p l a c e s as indicated by railway representative at site. [inspection by Consignee]. Total 7967523.45

Item Breakup - E1-Schedule E1: Electronic Interlocking

Supply of Electronic Interlocking System Station Complete Manufacture and Supply of Microprocessor based Electronic Interlocking(EI) system complete as per RDSO Specification No. RDSO/SPN/192/2019 Ver. 2 or latest with latest amendments, as per Special Conditions of Contract and Technical Specification enclosed, including all fixtures, interconnection cables and jumper wires, mounting arrangement and accesories to make the EI System functional at stations enclosed. This EI system shall be of Hot standby with Centralized Architecture. This system should have either relay interface or object controllers to drive field gears. If object controllers are used, it shall be installed at relay room of station.The system shall be designed with Dual Operator VDU of size 65"" with industrial grade Embedded Fanless PC as per RDSO TAN No.STS/E/TAN/3012 Version 3.0 or latest. The Signal lamps are to be lit with 110V AC in case of direct-fed signals. (B) Installation, Testing and Commissioning of Electronic Interlocking System Complete Design, Installation, Wiring, Testing and Commissioning of EI equipments as per RDSO Specification No. RDSO/SPN/192/2019 Ver. 2 or latest, including installation of Relay racks and Fixing & wiring of all types of interface relays, termination of interface wires on the CT rack (FTOT) and printing sleeve paritculars. The input and output cables/wires (RDSO approved) used for interface wiring of EI shall be made of twisted pair.(C) Submission of ""As Made"" documents for EI: The contractor has to supply six sets of documents as mentioned below along with system details, site installation details/drawings, maintenance manual, operation procedure in a bounded book as per practice of SW Railway. 'As made' shall be prepared by the Contractor in AUTOCAD 2000 or latest in A3 size. (System Configuration 2 ) All indoor work details shall be prepared by contractor and submitted to Railways before testing the circuits. On execution of the work, one copy of the 'As made' check print along with soft copy of the drawings shall be submitted for checking. The final negatives shall be made in tracing sheet and submitted to Railways for approval. On approval, the contractor shall submit along with the negatives, six sets of documents duly making neatly bounded booklets. Out of 6 sets, 2 sets of drawings and other plans shall be kept in transparent plastic cover (2 sheets back to back in one plastic cover) and handed over to Railways. Note: Complete Description of this item is uploaded along with the Tender Document as "" EI Schedule Complete Description. [inspection by RDSO]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply of Essential Spares at 10% for Set Normal Cards and 15% for Vital Cards for all kinds of EI module/cards as per

Item Breakup - F1-Schedule F1: Block, HASSDAC, MSDAC

Installation, testing and commissioning of Set high Avalibility HASSDAC t o b e installed, wired , tested and commissioned by OEM as per the guidelines issued by RDSO wiring discipline should be as per RDSO TAN No. STS/ E/TAN/ 6001 Version 1.0 or latest. The pre commissioning check list issued by RDSO for HASSDAC to be prepared by OEM and jointly signed by OEM & railway before commissioning of HASSDAC. OEM should submit site installation certificate.

Installation, commissioning of SSBPAC(D) and SM's Block panel with Block telephone complete including SPD & Auto change over card for Double line block working suitable for RE area. as per RDSO Spec No.RDSO/SPN/175/2005 VER-1 or Latest, (One set consist of two numbers).

Multi Section Digital Axle Counter - Station (MSDAC G 39 Version 00) as per RDSO specification, RDSO / SPN / 176 / 2013 version 3.0 Shifting of prewired racks and relay racks (all indoor equipment, consisting of fewer than 15 DP) from the old relay room to the new relay room.

Multi Section Digital Axle Counter - Numbers (MSDAC - G 39 Version 00) as per RDSO specification, RDSO / SPN / 176 / 2013 version 3.0. Wheel Sensor Base Clamp Type Split (G36-T212505 & G36- R212505). [inspection by Consignee].

Multi Section Digital Axle Counter - Numbers (MSDAC G 39 Version 00) as per RDSO specification, RDSO / SPN / 176 / 2013 version 3.0 Mushroom Box with Cover. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply, commissioning of Block proving by Digital Axle Counter (BPAC) using UFSBI for single line operation as per RDSO Specn. NO. IRS/S/105/ 20129 ( Ver.0) it comprises of auto change over facility for Quad and OFC working. Necessary modem for quad and OFC should be supplied along with auto changeover arrangement details are as follows. (I) Universal Fail Safe Block Interface (UFSBI) with complete accessories as per RDSO Spec No. IRS/S/104/2012 (II) Block Panel as per RDSO S-32019 (III) Relay rack with locking and sealing arrangement duly wired as per RDSO:S:32020 along with complete Relays. (IV) Block telephone with accessories as per RDSO/SPN/191/2005. (V) Automatic Media change over along with additional modem as per manufacture specification for BPAC using UFSBI(ITEM NO I) for supply of above items, Unit will be in set consisting of 02 Nos of each items. ( PTJ - TLBI instrument with UFSBI). [inspection by RDSO].

Supply, commissioning of Automatic Media changeover and modems working on redundant channels for data transmission on OFC/Quad. This included installation & configuration of Industrial grade modem, wraping of E1 connections etc.(Per Unit=Set Per Block Section). [inspection by RDSO]

Manufacture and Supply of Block Numbers counters as per the sketch 700mmx950mmx800mm with application of patty and good quality painting and shall have the provision to fix the PBT terminals boards and cableinlet holes at bottom (4 Places) and dummied.(Plywood sheet of thickness 25 mm x 25 mm x 6 mm,pad locks, tower bolds, Decolum Sheet for top, sheetguage for front slit door with tower top and bottombolts, paints, patty shall be supplied by the contractor.). [inspection by Consignee].

Supply of High Avalibility Single Section Set Digital Axle Counter (HA-SSDAC) with Dual Track sensor Devices as per RDSO specification No. RDSO/ SPN/ 177/ 2012 version 3.0 or latest ( Phase reversal type) as per details given below:a) Configuration 2DP-1 section. b) length of cable required with each track devices - 15 mtrs. [inspection by RDSO]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Microprocessor based Solid State Block Per Unit Proving by Axle Counter(Digital) [SSBPAC(D)] complete for Single line operation as per RDSO Spec. No. RDSO/SPN/175/2005Ver.1 or latest including Station Master's Block Panel, Wired Relay Racks with Relays, necessary Lightening & Surge Protection Devices for Power Lines 24V DC & Data Lines and Block Telephone as per RDSO/SPN/191/2005 or latest (Per Unit = Set Per Block Section). [inspection by RDSO].

Installation, Testing and commissioning Per Unit of SSBPAC(D) complete including Station Master's Block panel and Automatic Media Changeover Card for Single line operation as per RDSO Spec. No.RDSO/SPN/175/2005 Ver.1 or latest,. [All misc items required for comissioning shall be supplied by contractor (Per Unit = Set Per Block Section)

Installation, Testing and commissioning Per Unit of SSBPAC(D) complete including Station Master's Block panel and Automatic Media Changeover Card for Single line operation as per RDSO Spec. No.RDSO/SPN/175/2005 Ver.1 or latest,. [All misc items required for comissioning shall be supplied by contractor (Per Unit = Set Per Block Section)

Supply of Adaptor Card. [inspection by Numbers RDSO].

Supply of Display card of Block Panel Numbers (Eft-688M). [inspection by RDSO].

Supply of Modem Card (Eft-1000M2). Numbers [inspection by RDSO].

Supply of Non-Vital output module (Eft- Numbers 531M3). [inspection by RDSO].

Supply of Vital output module 532M3). [inspection by RDSO].

Supply of Voter card module (Eft-530M2). Numbers [inspection by RDSO].

Supply of Communication card Module Numbers (Eft-533MS). [inspection by RDSO].

Supply of Input Module (Eft-529-M3). Numbers [inspection by RDSO].

Supply of CPU module [inspection by RDSO]. Total 13426522.70

Item Breakup - G1-Schedule G1: Fire Alarm System

Supply, commissioning of Heat and smoke multi sensor as per RDSO/SPN/217/2021 ver-3 or latest. along with its base, backbox and all accessories with IS:2175 and IS:11360 standards and Under writers Laboratory (UL) listed. [inspection by RDSO].

Supply of Analogue linear heat sensing Metre (LHS) cable as per RDSO/SPN/217/2021 ver-3 or latest. [inspection by RDSO]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply, commissioning of linear heat sensing interface module, (Monitor module) for LHS cable with backbox and all other accessories as per RDSO/SPN/217/2021 v e r- 3 or latest in complaince with IS standards and Underwriters Laboratory (UL) listed. [inspection by RDSO].

Supply of Fire survival cable 2x 1.5 Metre sq.mm unarmoured as per RDSO/SPN/217/2021 ver-3or latest. [inspection by RDSO].

Supply, commissioning of Manual call point (resetabble) with backbox and all other accessories as per RDSO/SPN/217/2021 ver-3 or latest. [inspection by RDSO].

Supply, commissioning of Relay module with backbox and all other accessories as per RDSO/SPN/217/2021 ver-3 or latest. [inspection by RDSO].

Supply, commissioning of Hooter and Visual strobe alarm units with backbox and all other accessories as per RDSO/SPN/217/2021 ver-3 or latest along with its power supply unit. [inspection by RDSO].

Supply, commissioning of Control module with backbox and all other accessories as per RDSO/SPN/ 217/2021 ver-3 or latest. [inspection by RDSO].

Supply, commissioning of Monitor module for 3rd party with backbox and all other accessories as per RDSO/SPN/217/ 2021 ver-3 or latest. [inspection by RDSO].

Supply, commissioning of Networkable single loop addressable Fire alarm Control panel expandable upto 4 loops with GSM interface(without GSM module) as per RDSO/SPN/217/2021 ver-3 or latest. This work involves supply ,fixing, installation and testing of control panel. The control panel shall be networkable to Zonal /Divisional headquarters preferably over TCP/lP and shall have clock synchronization facility. This includes Networking module (TCP/IP) for control panel along with power supply unit and battery set of required capacity for 24 hours backup as per RDSO specification.. The panel should support degrade mode operation in complaince with IS: 2189 , EN 54 standards and Underwriters Laboratory (UL) listed. [inspection by RDSO].

CO2 installation , testing and commissioning of CO2 fire extinguisher 6.5 kg capacity conforming to IS 15683 with ISI mark provided with all fittings and accessories. Make Safex/Bharat or similar. [inspection by Consignee]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supervision, programming , testing & Numbers Commissioning charges for Aspiration smoke detection .

Supply Commissioning of aspiration type smoke detector. Highly sensitive smoke aspiration system for monitoring of rooms and equipment's for earliest possible fire detection For Relay rooms No.RDSO/SPN/217/2021ver-3 or latest. [inspection by RDSO]

Supply and Installation of Air sampling Numbers CPVC Pipes with all required accessories for Aspiration system . [inspection by Consignee]. Total 4638951.00

Item Breakup - H1-Schedule H1: Telecom Non- SOR

Supply and installation of 100 pair cable Numbers termination box (single door with lock & key, powered coated - Siemense grey) along with wago terminals as per technical specification.[inspection by Consignee].

Supply of Emergency Socket boxes of Numbers FRP make conforming to specification: RDSO/SPN/TC/44/2002 Ver. 3.0 and 6 pin socket flat as per RDSO Spec. IRS:TC: 42/2020 Ver. 1.1 or latest.[inspection by Consignee].

Provision of emergency communication Numbers along the railway track. Fabrication of emergency post as per drawing No. UBL/SG/CON/6/2004 and fixing of emergency socket post and burying the post to a depth of 1m after entry of cable. The post to be painted with red oxide before installation. This includes termination of derivation cables on termination strip inside the emergency socket, painting of emergency socket post with alternate black and white strips of 6" width. The paint used should be of standard quality and two coats of paints should be applied. The EMC post should be painted with red oxide base before painting.

Supply of 2/4 wire combined portable Numbers emergency control phone as per RDSO specification IRS TC 75/99 with amendment No.04. [inspection by Consignee].

Supply of 4 wire DTMF way station Numbers equipment as per RDSO specification No. IRS- TC 60/2007 with amendment no 1 latest with 4 wire control telephone as per specification no IRS TC@45&47@97 with Amendment No.2 latest.[inspection by Consignee].

Supply of Power Supply Unit for Way Numbers Station Equipment with MF Battery 12 Volt / 7 AH as per RDSO Specification No IRS-TC-72/97 with Amdt. 1 or latest. [inspection by Consignee]. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply, Installation and Commissioning Numbers for 4 Port Gateway to support 4 Port Concurrent Emergency Communication at HQ /Way station to support 4 wire ports as Per clause no. 10.1 of RDSO/SPN/TC/99/2023 Ver. 3.0 or latest. [inspection by Consignee].

Supply of Digital Clock suitable for Office Numbers Complex with GPS synchronisation in standalone mode (Colour of LED:Red) as per clause 6 of RDSO Specification No. RDSO/SPN/TC@47>47@2008 Rev.3.0 or latest along with GPS receiver as per Clause 8 of this specifications. This includes Supply and installation of complete GPS clock and receiver as per direction of Railway Site engineer of the Consignee.[inspection by Consignee].

Supply and transportation of Thermo Numbers shrink jointing kit RTSF4 for quad cable as per RDSO specification No.IRS.TC:77- 2012 (rev.3) or latest.[inspection by Consignee].

Supply management system (SC type) and termination of IN and OUT 24 fiber OFC cable as per TEC specification. (with all connector material) routing/dressing fiber as per direction of engineer/in charge. [inspection by Consignee]

Supply of Single Mode Patch Cord length Numbers 5 meters (LC-SC/SC-SC/LC-LC/FC-LC) as per site requirement. [inspection by Consignee]

Supply of factory crimped 2 meter CAT 6 Numbers Patch cord.[inspection by Consignee]

Supply of caller ID push button telephone Numbers similar to Beetel M59 ABS Telephone instrument.[inspection by Consignee]

Supply and installation of Layer 2 Switch Numbers of minimum 8+2 Port manageable with 8 Nos 10/100/1000 Mbps Ethernetport, POE + & single fiber 2 Nos 1G SFP Port with BX SM SFP Optical Modules loaded with all accessories. [inspection by Consignee]

Supply of GI back box of 4 modules to fix Numbers RJ-45/RJ-11/TV sockets into the box with suitable 4 way face plate.[inspection by Consignee]

Fixing of GI black box of 2 way/4 way/6 Numbers way and fixing the RJ11/RJ45/dish socket and terminating the suitable wires into the socket and installation of suitable face plates as per instruction of site incharges.

Supply of RJ-45 I/O concealed type of Numbers reputed make.[inspection by Consignee] UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply, Installation and Testing of Set Transceiver VHF Mobile 25 watt synthesized. Band: 136- 174 MHz Full band along with 3dB gain GP antenna suitable for the 25 watt VHF set with 30 mtr. RG-213 Co-axial Cable with both end Connectors suitable with the VHF set MAKE:- MOTOROLA OR KENWOOD and POWER SUPPLY unit, SMPS based,12 Volt DC, Output current: 15 Amp. Charging: Float & Boost mode Suitable for 25 watt VHF set.[inspection by Consignee]

Supply of Walkie Talkie Charger Model Numbers KSC- 43 Suitable for Kenwood TK 2207 / TK3207 / TK2207s of 5 watt Walkie Talkie set. Make/Brand KSC-43. as per clause no. 4.0 of RDSO/SPN/TC/107/2018 Ver.- 2.1 or latest. [inspection by Consignee]

Supply of Rapid Trichemistry charger Numbers base with adapter for Motorola GP 328/338, NiMH/Li-ion, LED indications, 1 to 3 hr charging time, AC Surge protection.[inspection by Consignee].

Supply of Kenwood Walkie Talkie Battery Numbers Model No. KNB-69L of 2550 mAH Liion.Battery Suitable to Kenwood TK 2207s Model as per clause no. 3.0 of RDSO/SPN/TC/107/2018 Ver.- 2.1 or latest. [inspection by Consignee].

Supply of batteries OEM approved for Numbers Motrola GP328, 5watts walkie Talkie sets, 2 volts , ni-mh, 2400 Mh or similar as per specifications.[inspection by Consignee].

Supply of Helical Antenna Kenwood Numbers Suitable for TK-2207 Make Model: KRA 26 as per clause no. 5.4 of RDSO/SPN/TC/107/2018 Ver.- 2.1 or latest. [Inspection by Consignee]

Supply of Helical Antenna suitable for Numbers Motorola GP-328 WALKIE TALKIE sets . [Inspection by Consignee].

Straight through/derivation with/without Numbers transformer joints: Installation Thermo shrinkable jointing kits for straight through /derivation joints for LC gate, pump houses etc where VF transformers are not required and derivation joint by using 2T transformer (to be housed in the joint). This includes tapping of nominated Quad at a specific location shown by the Railway Engineer at site to the jelly field cable already laid. All materials including valco tapes except thermo shrinkable jointing kit shall be supplied by the contractor.(Refer Annexure for instructions on cable jointing).

Supply and installation of SIP Based Basic Numbers IP Phone as per Specification. [Inspection by Consignee] UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Shifting and Wiring of complete Telecom Numbers equipments, SDH ADMs, PDMUX, Maple MUX with accessories, surge protection arrangement, FDF, racks, DDF, runway ladder and Shifting & re-wiring of PRS/UTS Equipment etc which available in OFC/SM Room. this includes connecting all pigtails and optical patch cards etc. to SDH and primary mux equipment with all interface cards to 48V bus including supply of wires and connectors, terminations of all E1s on DDF, termination of VF interface circuits to krone type MDF at both ends including taking PVC cable over runway or a wall, krone type DP with all surge and lighting protection complete for all the circuits derived from PD mux. This work includes wiring and connection of telephones in SM's room and extension of generator supply equipment. All miscellaneous materials like power wires conduit and accessories etc. shall be supplied by the contractor. Suitable link panel should be provided on this rack for testing and isolation of fault.

Telecom WAGO/Pheonix/Elmex make or similar disconnecting Terminals blocks of size 1500mm x 600mm x 200mm thickness 1.6mm (16 SWG) in two compartments with single transparent door and locking facility integrated with 3 rows, (2 rows consisting of 50 nos of 2 conductor cage clamp disconnectng type terminal blocks & one row consisting of 10X10 krone modules) (accessories such as end stops&end plates are a part of the terminal blocks) additional krone hand tool-1 nos will be supplied. [Inspection by Consignee]

Fixing of telecom termination panel and Numbers termination of cables on WAGO krone connectors as per the instructions of site engineer.

Supply of 2 MP Full HD CMOS image Numbers sensor dome camera as per the enclosed specifications. The OEM should comply with a valid STQC ER certificate. [Inspection by Consignee]

Supply of 16 channel NVR supporting IP Numbers camera as per specification enclosed. [Inspection by Consignee]

Supply of 8 TB Hard disk for NVR. Numbers [Inspection by Consignee].

Installation & commissioning camera with accessories.

Installation & commissioing of 16 channel Numbers NVR with accessories.

Supply and installation of 3 MP PTZ dual Numbers camera, 256 GB SD card Wi-Fi,SIM based, solar power with built in battery. [Inspection by Consignee]

Supply & installation of jointing chamber Numbers as per drawing with cover and required trenching to ease out cable duct. [Inspection by Consignee]

Providing dry sand in FRP/RCC joint Numbers chambers upto 400mm height. UBL-PROJECT-S AND T/SOUTH WESTERN RLY

Supply & installation of OFC joint closure Numbers (Normal Joint/ T-Joint) including splicing (24 Fiber).[Inspection by Consignee]

Splicing /Dropping/Termination of each CORE Fiber /Pigtail in the LIU/FDMS/Termination Joints through fusion Splicing of the termination of OFC Cables. Total 4316445.12