Special repair to MD Accn of KV school at Varanasi Cantt Under GE (East) Prayagraj.

Amount

Demilition of cement concrete of any description and in any position is reinforced (reinforcment cut as required to facilitate demolition) not other wise specifically provided for complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L for 25mm thick Cement concrete 1:2:4, type B-0 (using 12.5mm graded stone aggregate) in levelling course, benching etc, finished even & rough to receive cement mortar screed bed complete all as specified and directed.

M & L for 75mm thick Cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) in levelling course,for floor benching etc, finished even & rough to receive cement mortar screed bed complete all as specified and directed.

M&L for chequered cement concret tiles, 25 mm thick, machine pressed set jointed and pointed in neat cment slurry, in floors with grey cement and pigment over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) in plinth protection,, finished surface even and smooth without using extra cement, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Roughening surfaces of old concrete floors by picking, sweeping clean and wahsing down with water to remove dust etc, complete all as specified and directed

M&L for Non - skid Coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

All as per item No. 09 above but as in vertical surfaces such as skirting/ dado over and including rendering layer 10 mm thick in CM (1:4) complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface, size 450X 300X 7mm thick ,set and jointed in neat cement slurry and pointed in white or colour cement to match in coloured cement to match tiles over and including 10 mm thick rendering layer in CM (1:4) complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab over and including 20 mm thick screed bed or bedding layer in CM (1:4), rubbing and polishing complete all as specified and directed.

M&L for Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid and jointed with grey cement mixed with pigment to match the shade of slab over and including 10 mm thick screed bed or bedding layer in CM (1:4), rubbing and polishing complete all as specified and directed.

M&L for Makrana white marble tiles 18-20 mm thick, machine cut, bedded, jointed and pointed with grey cement slurry including cutting and polishing complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work class 'B' old sizefly ash bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with class 'B' old sizefly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15 mm thick on wall, in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 10 mm thick on wall, in cement mortar 1:4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specfied and directed.

M&L for Rendering 5 mm thick in cement mortar 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement , complete all as specfied and directed.

S&F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specfied and directed.

M&L for preparing new plastered surfaces of walls, applying two coats of Oil bound distemper in approved colour/shade over a coat of primer including application of 1mm thick wall care putty for preparation of smooth finish wall surfaces complete all as specified and directed.

M&L for preparing new plastered surfaces of walls, applying two coats of cement base paint in approved colour/shade over a coat of primer including application of 1mm thick wall care putty for preparation of smooth finish wall surfaces complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with machenical scrapping machine, including filling depressions of scrapped surfaces and prepairing old decorated plastered surfaces of wall including cornices,pilastered etc. and applying two coats of Oil bond distemper over one coat of primer over wall care putty on wall surface complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with machenical scrapping machine, preparing surface by applying wall care putty (min. 1mm thick) on screpped wall surface, cornices, pilastered etc. (for filling depressions and make surface smooth) and applying two coats of cement base paint complete all as specified and directed.

M&L for preperation of old surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

Dismantaling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 15-20mm thick Granite (of any type) work (table rubbed and polished and moulding of outer edges) in steps, jambs and pillars, window cills, cooking platforms and the like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed .

Taking up or down steel tubing and connections and supply and fixing 15mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

Taking up or down steel tubing and connections and supply and fixing 20mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors all as specified and as directed.

Taking up or down steel tubing and connections and supply and fixing 25mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

S&F in repair, 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) of 500 litres capacity, ISI marked double layered, hoisted and fixed in position, connecting up pipes etc including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210 gms) and dismantling water tanks & removeing from site complete all as specified and directed.

S&F in repair 20mm bore PVC nipple suitable for HDPE water tank. (Minimum weight 45gms) complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe , complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, white coloured, with integral foot rests, including provision of lime concrete bedding complete all as specified and directed.

S&F in repair Vitreous china coloured wash down water closet pan (Padestal Pattern) with fixing bolts, including connection to flush pipe, 'P' or 'S' trap, antisyphonic pipe etc and PVC seat cover with chromium plated mild steel hinges device, complete all as specified and directed .

S&F in repairs Vitreous china wash basin, white, flat back, size 550x400 mm including brackets and cutting for and pinning in ends of brackets,complete all as specified and directed.

S&F in reapir primium stainless steel soap dish complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125 mm size with swivel joints, complete all as specified and directed.

S&F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges brackets complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair fancy type bib taps cast copper alloy chromium plated with crutch or butter fly handle screwed down screwed for iron pipe 15mm bore complete all as specified and directed.

M&L for preparing new surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparing old painted surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing old painted steel & iron surfaces of any description over 10 cm in width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L preparing new steel & iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1(using 20 mm graded stone aggregate) in chajjas and similar work (reinforcement to be measured separately) complete all as specified and directed.

M&L for form work to chajja and similar work including edges for flat rough finished surface of concrete complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8 mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F in repair 15 mm dia fancy type chromium plated with long shank and cup angle valves cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete and all as specified and directed

S&F in repair 15 mm dia stop valves cast copper alloy chromium plated long shank(concealed type), screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs grating doom 125 mm dia with waste hole of PTMT (min weight 40 gms) complete all as specified and directed.

S&F stainless steel tubing of 25 mm dia as in curtain rod including end brabs brackets, socket and knobs (wall to wall or flush to wall) for securing to curtain rod, fixed in repair complete all as specified and directed.

Taking down chowkhat with shutters (W/O taking off shutters from the frame), area of each opening exc. 1.50 Sqm but n exc. 4 Sqm complete and all as specified and directed

Taking down chowkhat with shutters (W/O taking off shutters from the frame), area of each opening n exc. 1.50 Sqm complete and all as specified and directed

S&F Flush shutters 30mm thick, solid core consturction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick glazed and skeleton shutters of 2nd class HW open rebated and prepared to receive glass or gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered bead for securing glass/gauze etc size of shutter as specified in SSR part I section 8, clause 8.24(a) complete and all as specified and directed

S&F 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The Lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two laces by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete all as specified by the manufacturer and as per directions of Engg-in-charge.

S&F factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm frame complete all as specified by the manufacturer and as per directions of Engg-in-charge.

M&L for rolled mild steel sections conforming to Gde Fe-410-0 (Grade E-250) quality A as in framing for cladding, glazing and the like including door frames/chowkats, cooler stand fixed with angle cleats and connecting plates, etc complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as bed blocks for fixing hold fasts and similar woek includnig necessary form work complete all as specified and directed.

S&F 200 mm long alluminiuml anodised tower bolt, complete and all as specified and directed

S&F Aluminium alloy, anodised, sliding door bolt 300 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised150mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised100mm size complete all as specified and directed.

S&F Hasp and staple 150 mm size, safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate, fixed with screws in repair complete all as specified and directed.

Supply only Second class hard wood small fittings such as brackets of any type, shaped door and window stops and the like, including all necessary labours, articles not exceeding 200 cu. cm each complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 50 mm size complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete and all as specified and directed

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete and all as specified and directed

S&F 18/19mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed .

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open) complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, with glazing bars complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, without glazing bars complete all as specified and directed.

S & F steel ventilators with top hung shutter including hinges, steel peg stay including two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm in each panes complete and all as specified and directed

S&F, 3mm thick Figured glass, pin headed type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repair of 3mm thick sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed .

M&L for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed .

S&F in repair 110mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints,fixed to walls complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints,fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single (SingleT)equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single (SingleT)equal or unequal complete all as specified and directed.

S&F 110mm PVC (SWR) Vent cowl complete all as specified and directed.

S&F 75mm PVC (SWR) Vent cowl complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrte type B1 (1:2:4) suitable for 75mm bore pipe complete all specified and directed.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs Stainless steel plate rack (utensil rack) of size (600mm x 750mm) and depth 300mm made with 0.63mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts fixed complete all as specified and directed.

S&F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (minimum weight 300 gms) complete all as specified and directed.

S&F in reapair 15mm bore fancy type pillar tap cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered 'hot' or 'Cold' with long screwed shanks and fly nuts fixed to pipe complete all as specified and directed.

M&L for Plain cement concrete, 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels or drains, complete all as specified directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete all as specified directed.

M&L for providing cement concrete type B0 1:2:4 (using 12.5mm graded crushed stone aggregate) in roof kerbs or mud stops, rounded or chamgered on edges and misc surfaces using water proofing compound, complete all as specified and directed. (Note: water proofing compound shall be paid separately).

M&L for application of glass fibre reinforced acrylic modified cementitious coating system in sunken portion as top coat @ 1.5 kg/m2 over and including protection plaster (12–15 mm) admixed with appropriate integral waterproofing compound @ 0.10 kg per bag of cement after prepration of surface i.e. cleaning of RCC surface to remove dust, loose particles, and grinding any sharp edges complete all as specified and directed. NOTE :- (i) The product should conforms to IS 2645. (ii) Pipe penetration of toilets core cutting shall be sealed using solvent free, moisture insensitive epoxy resin based patch repair putty on pipe penetration surfaces. The putty shall be applied to a groove thickness of minimum 20mm on pipe penetration joint to concrete including 50mm dia spout pipe .The cost of this process deemed to be included in qouoted rate.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as filling in sunken floors and similar works including demolition of existing cement concrete (un-reinforced) any position and any thickness including removal complete all as specified and directed.

Welding in repairs n. exc 2.5cm in length and not exceeding 6 mm thick for steel window ventilator and steel gate/door etc., errecting in position to make functional complete all as specified and directed .

Repairs to existing steel rolling shutters without ball bearing by taking down top cover, anchoring rod, spring etc and providing new springs and anchoring rod, replacing the worn out strips of shutters and welding of handle, hasp staple and other broken articles etc, greasing the spring, guide rail, shaft etc and making functional and errecting in position, including refixing of top cover / hood etc, opening n.exc. 10 sqm each and finally painting with two coats of synthetic enamel paint, complete all as specified directed. Note : Springs, anchoring rod, worn out strips, handle, hasp staple etc shall be paid seperatly under respective items here-in-after as supply only

Removing / taking down of existing water proofing treatment of any pattern/thickness from roof/concrete surfaces, cleaning the surface by means of sweeping, washing etc so as to make the concrete surface ready to receive new WPT with entire setisfection of Engineer -in-charge including removal of debries to a distance exc 250 Mtr where directed complete all as specified and directed.

M&L for providing water proofing treatment over cleaned roof surface using APP modified bitumenous membran, weight not less than 3 Kg per Sqm comprising of the following and testing complete:- [a] 10 mm thick rendering or screed bed or bedding layer in cement sand mortar 1:4 mixed with water proofing compound @ 3%by weight of cement and surface finished even & fair. [b] Applying one coat of bitumen primer @ 0.3 Litre per Sqm on plastered surface. [c] Applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg per Sqm. [d] laying APP modified polymeric water proofing membrane having weight not less than 3 Kg per Sqm with 100 mm wide side or end lap and joint sealed with flamed torched pasted over full length [e] Applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg per Sqm. [f] Spread coarse sand over entire bitumen surface and than topping with 40mm thick 250x250x25mm concreat tiles laid over & including 15 mm thick screed bed in cement sand mortar 1:6, jointed and pointing with CM 1:3 complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Taking down shutters of any description area not exceeding 1.00 Sqm and removing from site, complete all as specified and directed .

Taking down shutters of any description, area exc 1.00 Sqm bu n'exc 2.00 Sqm each, and removing from site, complete all as specified and directed .

Supply only Spring suitable for rolling shutter reaired under item No. 110 here-in - before,

Supply only anchoring rod suitable for rolling shutter reaired under item No. 110 here-in - before

Supply only worn out strips suitable for rolling shutter reaired under item No. 110 here-in - before.

Supply only handle suitable for rolling shutter reaired under item No. 110 here-in - before.

Supply only hasp staple suitable for rolling shutter reaired under item No. 110 here-in - before.

Taking down carefully aluminium point wiring(any type)for one light point, fan point ,exhaust fan point, bell point, power point complete including all fittings such as switches, socket, pendents holder, ceiling rose, sketch fittings, tube light fittings, regulatores unscrewing the switch sockets, ceiling rose, regulators from boards/outlet boxes and making good the disturbed surfaces of wall/ ceiling and colour washing matching with the existing colour wash all as specified and directed by Engineer-in-Charge.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/bell/buzzer / exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

Ditto- all as item No.122 here-in-before but for one light controlled by two way switch

Ditto- all as item No. 122 here-in-before but one 3 pin, 5amp socket out let on independent board complete all as specified and directed.

Ditto -all as item No.122 here-in before but 3pin, 5amp socket out let on the same board with other switch complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 4.0 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/bell/buzzer / exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 2.5 Sqmm FR type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

M&L sub main wiring with two single core PVC insulated & unsheathed cable 6.0 Sqmm (nominal area) FRLS type having multi-stranded copper conductor drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring with and including 4.0 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as earth wire connected to common earth as per IS & cutting chasing for conduit & sinking for boxes & making good to walls disturbed surface & applying finishes to match existing surface complete including taking down of exsting sub main wiring complete all as specified and directed. NOTE : Two runs of 6 Sqmm and one run of 6.0 Sqmm cable and PVC conduit shall be measured as a one unit length.

S & F for switch piano, flush type, 5 amps, single pole , one way , 230 volt complete all as specified and directed.

S & F for switch piano, flush type, 5 amps, single pole , two way , 230 volt complete all as specified and directed.

S & F bell push switch 5 Amp flush type complete all as specified and directed.

S & F for 2/3 pin, 5 Amp/ 6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

S & F for bell, ding- dong , AC, 230 Volt, single pole complete all as specified and directed.

S&F lamp holder PVC/Polycorbonate type with cord grip cap/back plate suitable for batten/angle /pendent fitting complete all as specified and directed.

S&F LED retrofit lamp of capacity 12/15 watt, B-22 holder base with polycabonate body and aluminium heat sink warm white complete including taking down old/ unserveciable CFL/bulb complete all as specified and directed.

S&F switch socket combination 2 in 1, 6 pin 16Amps multipurpose type 240 volts complete all as specified and directed.

S&F ceiling rose single phase , PVC poly carbonate,insulated body three terminals ISI marked complete all as specified and directed.

S&F stepped type electronic fan regulator flush type 2 module AC 230 volt suitable for any type of ceiling fan complete all as specified and directed.

S&F in repair LED tube light fitting ,20/22 Watt ,decorTive type ,slim alluminium square profile ,high lumen output energy efficient ,direct surface mounting including connecting up with twin core PVC insulated copper conductor of suitable size, including taking down the old unserviceable light fittings complete all as specified and directed..

S&F LED integral ultra slim round shape surface mounting high power LED luminaire , dome shape opal diffuser lamp of capacity 18w complete including taking down old/ unserveciable CFL/bulb complete all as specified and directed.

S&F Phillips comet wall light unique Aesthetic white colour having suitable holder for B-22 Bulb complete including taking down old/ unserveciable CFL/bulb holder complete all as specified and directed.

S&F LED edgelite linear & compact 9W mirror light with decorative grey end caps , polycarbonate body and ribbed opal dufuser of Make Havells or equivalent of Make of Philips/Bajaj including taking down the existing unserviceable light/mirror fittings complete all as specified and directed.

Supplying, installation and testing of energy efficient five star rating electric water heater 25 litres 2 KW (Geyser), ISI marked including fixing the water heater (geyser) on wall with and includng nuts bolts/anchoring bolts and making water /electric connection and making good disturbed surface of wall to match the existing complete all as specified and directed

Supply and Fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB single pole 20 amp complete all as specified and directed.

S&F 15 mm dia stop valve fancy type chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair bib taps cast copper alloy chromium plated with capstan head screwed down, screwed for iron pipe or for brass ferrule 15 mm bore of approved make complete all as specified and directed.

S&F hot water outlet PVC connection heavy duty made of chromium plated nut, bolts and flexible tubing 15 mm dia, 450 mm complete all as specified and directed.

Supply & fix exhaust fans of metallic body heavy duty AC single phase 230/ 240 V of size 300 mm sweep with bracket, louver shutters, nuts & bolts including connection with PVC copper flexible wire for Exhaust fans complete all as specified and directed. Note: cost for drilling Suitable dia of hole in the wall deemed fit in quoted rate

S & F Building security/street LED light fitting 35 watt IP-65 protection pressure diecast alluminium body ,heat resistant glass ,including driver and making necessary electric connection with 2.5 sqmm twin core copper wire fixed in GI pipe 1 m long complete all as specified and directed.

S& F for sheet metal enclousre factory made for MCB DB's SPN, 8 way, double door, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete make -Havells all as specified and directed.

S& F for sheet metal enclousre factory made for MCB DB's TPN, 4 way, double door, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete make -Havells all as specified and directed.

S&F Isolator/MCB TPN 240 Volt 63 Amp ISI marked conforming to 'C" curve, breaking capacity 10 KA complete all as specified and directed.

S&F Isolator/MCB SP 240 Volt 6 TO 40 Amp ISI marked conforming to 'C" curve, breaking capacity 10 KA complete all as specified and directed.

S&F Isolator/MCB SPN 240 Volt 40 Amp ISI marked conforming to 'C" curve, breaking capacity 10 KA complete all as specified and directed.

S&F Isolator/MCB SPN 240 Volt 63 Amp ISI marked conforming to 'C" curve, breaking capacity 10 KA complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galavanised earth lead wire 4.0 mm dia (7.5m) as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISImark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing of earthing & dismantling /taking down existing old / unserveciable earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe upto 7.5 meter beyond the earth plates electrode.)

Supplying ,laying, commissioning & testing cross sectional area 25 Sqmm , 3.5 core XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down existing old /unserveciable cable complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,laying of cables etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L Sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed. NOTE : Punned thickness only shall be measured.

Supply and laying dry well burnt locally available brick sub class'B' modular bricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as spcified and directed

Bore hole for passing cable through / insertion of 50mm dia GI pipe under PCC road/ taxi track/ runway/ hard standing (without damaging the surfac), upto the depth 450mm to 1200 mm complete all as specified and directed. NOTES :- (i) Cost of equipments, tools & plants, material required for boring shall be deemed to be included in unit quoted rates above. (ii) GI pipe 50mm dia shall be measured and paid separetely.

S &F for 50 mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hardstanding including taking down existing pipe complete all as specified and directed.

R.S Enterprises