PROVN OF SENTRY BOX SHED AND GUARD ROOM AT 2003 STATION AND SPECIAL REPAIR FOR REPLACEMENT OF EXISTING PCC LT POLE TO STEEL TABULAR POLE INCLUDING ALLIED WORKS AT AF STATION GURGAON UNDER GE AF GURGAON

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out all as completed.

Excavation in trenches n.exc 1.50mtr wide and 1.50mtr in depth for foundation etc or for shafts, wells cessipts, manhole etc not exceeding 10 Sqm on plan and not exceeding 1.5 mtr deth and getting out in soft /loose soil etc complete all as specified and as directed

Removing excavated soil/ building material/debries to a distance exc 250 mtr but not exceeding 500 mtr and depositing where directed etc complete all as specified and directed

Returning filling in, with soil inlcuidng spreading, levelling, watering and well ramming in layers not exc 25 cm thicks etc complete all as specified and as directed

M&L for cement concrete 1:2:4 type B-2 (using 40mm graded aggregates) as in foundation , filling in and mass concrete etc complete all as specified and directed

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) foundations, including rafts, footings, foundation ,beams; plinth beams; bases for columns, etc.; basement slabs, under- eamed piles and mass concrete complete all as specified and as directed .

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) for Columns, pillars, piers, posts and struts complete all as specified and as directed .

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed .

M&L for M-25 Reinforced cement concrete (using 20mm graded aggregates) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed . Note for Srl No. 6 to 9 :- Design mix shall be got approved by GE before incorporation in the work.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter all as specified.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) all as specified.

M&L Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. all as specified.

M&L for fly ash brick work straight or curved on plan exc 6.0 mtr mean radius built in CM 1:4 etc complete all as specified and directed

M&L for 15mm thick Rendering on fair faces of brick work or concrete sureces in Cement Moratar 1:6 finished surface even and smooth without using extra cement.Note the area includs in this up to 4th stories building complete all as specified and as directed .

M&L for 15mm thick Rendering on fair faces of brick work or concrete sureces in Cement Moratar 1:4 finished surface even and smooth without using extra cement complete all as specified and as directed .

M&L for 5mm thick Rendering on ceiling surface fair faces of brick work or concrete sureces in Cement Moratar 1:3 finished surface even and smooth without using extra cement complete all as specified and as directed .

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F Aluminium anodized powder coated ventilator/Window Double Shutters Glazed and Gauged of Stainless Steel Wire Cloth having nominal dia of Wire 0.36mm and average width of aperture 1.40mm along with Aluminium Section with 50 micron anodizing size of Frame 125x44.5mmx16 gauge having size of Shutter, Top/ Bottom/central Rail shall be 44.5x44.5mm x16 gauge Aluminium Section with 50 micron anodizing and 5.5mm thick Black/ Tinted Sheet Glass to be fixed on Glazed Portion including Aluminium Grill and Stainless Steel Hooks and Eye to be provided as stay of Shutters, etc. complete including necessary Jointing Cleats, Glazing Clips, Rubber Packing, Aluminium Snap Beading, Screws anodized Aluminium Fittings such as Peg Stay 150mm long (1 No. for each Leaf), Hinge Type B-21 of 100mm long (2 No. for each Leaf), suitable Handle (1 No. for each Leaf) and 100mm Aluminium Tower Bolts (2 No. in each Leaf), complete all as specified and as directed. NOTE : (a)Cost of Black/Tinted Sheet Glass, Stainless Steel Wire Cloth, Jointing & Packing Materials, anodized Aluminium Fittings, etc. shall deem to be include in the Quoted Unit Rate. (b)For the purpose of Measurement & Payment Double Shutter with Frame shall be considered as One Unit.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 125x60mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-0 (12.50 mm graded aggregate) back of chowkhats and incl two coats of synthentic enamel paint all as specified.

S&F in repairs Factory made solid panel moulded PVC door shutter wood grain 30mm thick(style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall becovered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottim rail. Penelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F PVC wood grain moulded Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS Square tub, suppling & fixing in opening as per specification and drawing.

S&F 100mm Butt hinges, meduim weight, cold relled stainless steel and fixed

S & F for aluminium anodised, barrel tower bolts of extruded section 125mm long and fixed

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

S&F 30 mm thich 2nd class Hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, guaze etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securiing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(a) and fitted to chowkats complete all as specified and as directed .

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and as directed .

S & F for Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed .

S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of exctruded sections or cast aluminium alloy and fixed.

M&L Glazed coloured ceramic tiles in vertical surfaces 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed .

M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4 complete all as specified and directed

M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4 complete all as specified and directed

M&L 25mm thick Cement concrete 1:2:4 type B-O(using 12.5mm graded aggregate) as in flooring, finished surfaces even and smooth without using extra cement complete all as specified and as directed .

S&F 15 mm bore CPVC tube all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed .

S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed .

S & F 15mm bore Bib taps, fancy type chromium plated cast copper alloy with crutch or butterly handle, screwed down, screwed with cup for iron pipe or for brass ferrule and fixed complete all as specified and directed

S & F 15mm bore Stop Valve/ angle valve fancy type chromium plated , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends with cup for iron pipe or for unions and fixed complete all as specified and directed.

S & F 15mm bore Pillar taps central hole Basin mixer with regular spout without popup waste system with 450 mm long braided hosedd 20 mm carttridge size fancy type, cast copper alloy, chromium plated, complete all as specified and directed.

S & F 15mm bore brass CP wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting & wall flange fancy type, cast copper alloy,chromium complete all as specified and directed.

S & F single towel rall 450mm long fancy type chromium plated fixed with PVC plug and steel screw complete all as specified and directed.

S & F towel ring round with round flange fancy type cromium plated fixed with PVC plug and steel screw complete all as specified and directed.

S & F soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed.

M & L in repair for hand shower (health faucet) with 8mm dia 1.20 mm lonf flexible tube and wall hook complete all as specified and directed.

S & F in repair for PVC conection 15 mm size with PTMT nuts of length 450 mm long

S & F in repair Swivel shower of PTMT any colour for fixing with 15mm pipe Minimum weight 40gms complete all as specified and directed.

S & F Vitreous Chine wash down water closet pan single piece with UF seat cover hinges, fixing accessories set, cistern fitting of size 365x655x760 with S trap complete all as specified and directed.

S&F vitreous China wash basin white, flat back size 550x400mm including S&F 32mm dia waste coupling, waste PVC pipe complete all as specified and as directed.

Supply only 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve float, handle including bracket complete all as specified and directed with glaged finish.

S& F stain less steel decorative cutrain rod of 25 mm bore inluding 2 nos steel finale and bracket 02 nos etc and fixed to wall with plastic rowl plug and steel screw complete all as specified and directed.

S&F 100mm PVC waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors all as completed.

S&F 75mm PVC waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors all as completed.

S&F 75mm bore Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed to walls all as completed.

S&F 75mm bore Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as completed.

M &L for prepepring the entire surface with appliying 2-3 mm thick putty on wall surface internal surface finished even and smooth complete all as specified and directed.

M & L for new plaster surface applying two coat Oil Bound distember on wall surface with roller brush complete all as specified and directed.

M & L for prepring new plaster surface and applying two coat of cement base paint on wall surface complete all as specified and directed.

M & L for new plaster surface applying three coat white wash ceiling surface with roller brush complete all as specified and directed.

M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over pink primer complete all as specified and as directed .

M&L for preparing new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enemal paint complete all as specified and directed.

S&F rotational moulded polythene, triple layers, (white)water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position incl S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed incl Dismantling water tanks Exc 250 Ltr & not exceeding 500Ltr complete all as specified and as directed .

Appliying 15 mm thick cement plaster with CM 1:4 smooth with adding 200ml water profing compound at 50 kg of cement finish the surface clean with water at roof complete all as directed by Engr-in-Charge.

M&L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) with 15 cm longitudinal & horizontal over lapping and joints finally pasted with thermo- fused withblow lamp laid over a coat bitumen @ 1.20 Kg /Sqm over bituminous primer 0.30 ltr per sqm as per APP manufacturer instructions etc complete all as specified and as directed. Note :-item includes repair in patches complete all as specified and directed by Engr-in-Charge.

M&L two coat of aluminium paint over top surface of water proofing membrane etc complete all as specified and as directed

Excavation in post holes (or similar holes) in hard /dense soil each n exe 0.5 cu.m, gettting out, returning, filling in and ramming earth or broken rubble mixed with earth around , in layers not exeeding 25cm, watering, and removing surplus soil to a distance n exe 50 m and making good surface complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 1.50 km and n exc 5.0 km depositing outside of MOD land or where directed

Hardcore of guage exc 63mm,Broken bricks, spread & leveled in two layers n exc. 15 cm thick , watered & rammed to a true surface complete all as specified and as directed.

M&L for providing cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregates) as in foundation filling and mass concrete , post holes, cills, steps; seismic and other similar bands, plinth courses, string courses, ramp, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , on roofs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, etc including necessary formwork complete all as specified and directed by Engineer-in-Charge.

S&F rolled sections, MS Angles, MS tubular Structures, MS Channels, Tee, etc. (Fe 410-W Gde-E-250 quality-A) as in main and cross beams, hip and jack rafters, purlins , posts,trusses (framed or unframed) structures where connected to common rafter and running rails and guides for sliding doors, fixed with angles clleats or other connecting plates all as specified.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,with riveted, bolted or welded attachment Fe-410-W(Gde E-250) quality B complete all as specified and as directed.

M&L for preparation of new surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surface over 10cm width or girth complete all as specified and as directed.

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa with hot dip alloy of 55% Al, 43.5% Zinc and 1.5% silicon and finished with resin coat on both side @ 150 gm/sqm as in roof covering/cladding/ridge to wall, fixed with self tapping screws as specified and directed by Engineer-in Charge

M&L for surface dressing upto a depth of 15 cm (on average) as in soft/loose soil all as specified and directed

M&L for 100 mm thick PCC 1:4:8 ( 40 mm aggregate ) as in subbase complete all as specified and as directed.

Machine pressed precast concrete glossy interlocking color rubberised paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade finishes complete all as specified and as directed.

M&L for 25mm thick sand cushioning including watering and consolidations etc complete all as specified and directed.

Brick work with fly ash bricks (Old Size bricks) straight or curved on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:4 (Externally) on Fair Faces of Brick Walls finished Even and Smooth without using Extra Cement and applying two coats of cement based paint complete all as specified and as directed.

Excavation over arear n.exc1.50mtr in depth for foundation etc or for shafts, wells cessipts, manhole etc not exceeding 10 Sqm on plan and not exceeding 1.5 mtr deth and getting out in soft /loose soil etc complete all as specified and as directed

Excavation over area exc 1.50mtr in depth for foundation etc or for shafts, wells cessipts, manhole etc not exceeding 10 Sqm on plan and not exceeding 1.5 mtr deth and getting out in soft /loose soil etc complete all as specified and as directed

Formwork to Columns, pillars, beams, bressumers, piers, posts and struts complete all as specified and as directed.

M&L for Glossy Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments all as specified and directed

M&L for point wiring for light points controlled by two, two way switch using 1.5 Sqmm nominal cross sectional area copper conductor multistranded, PVC insulated unsheathed FRLS cable in and including Heavy duty 2mm thick ISI marked concealed conduit of suitable dia complete with all ISI marked PVC conduit accessories/ fittings and 1.5 sqmm nominal cross sectional area stranded copper conductor PVC insulated unsheathed FRLS green colour cable earth wire and connecting to earth dolly etc. complete all as specified and directed. The point wiring shal include the wiring of light/ outlets of any length from the distribution board via switch to the point.

One light/fan point controlled by one switch.

One socket outlet 5 Amps on the same board.

One 3 pin socket outlet 5 Amps independent.

All as per item No. 83 above but with 2.5 Sq mm two single core and 2.5 Sq mm one single core as earth wire for 15 Amps socket.

S&F piano switch flush type 5 Amps 230 Volts single pole one way complete all as specified and directed by Engineer in Charge.

S&F piano switch flush type 15 Amps 230 Volts single pole one way complete all as specified and directed by Engineer in Charge.

S&F socket outlet combination 2 in 1, 3 pin 5 Amps flush type universal complete all as specified and directed by Engineer in Charge.

S&F socket outlet combination 2 in 1, 3 pin 15 Amps flush type universal complete all as specified and directed by Engineer in Charge.

S&F steped type electronic fan regulator flush type on the existing phenolic laminatedsheet etc complete all as specified and directed by Engineer in Charge.

S&F ceiling rose surface bakelite 3 terminal with base plate complete all as specified and directed by Engineer in Charge.

S/F LED tube light fitting 1x22Watt Saviour slim energy saving channel suitable for LED lamps with standerd fittings all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed at site.

S&F sheet metal enclosure for MCB's (D.B) 8 way (SPN) 200 Amps rated bus bar complete all as specified and as directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engineer in Charge.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN poles and 40 AMP current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and directed.

Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep BEE 5 star rated complete all as specified and directed by Engineer in Charge.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer in Charge.

Supply and laying in replacement for unsv cable XLPE insulated screened PVC bedded. Galvanized steel strip or wire armoured ,electric power cable(heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core comlete all as directed by the Engineer-in-charge.

Ditto all as per item no 101 described here in before but 3.5 core 25 sqmm.

M&L for drilling hole under hard standing /road in different location as per site requirement (between 03 mtr to 12mtr maximum) for laying of pipe for protection of cable etc by means of mannual bookle and without disturbing the top surface and making good the disturbed surface if any complete as sepecified and directed by Engr-in-Charge.

Supply and laying GI tube medium grade 80 mm bore, ISI marked complete as sepecified and directed by Engr-in-Charge.

Excavation in trenches in hard/dense soil , not.exc 1.5 mtr wide and not.exc 1.5 mtr deep and getting out in hard/dense soil for laying of cable/foundation of pole and stay etc in complete as sepecified. Note- Interlocking tiles dismantling during excavation and refixing the interlocking tiles including PCC after laying is included in this item.

Removal of excavated material/surplus soil to a distance n exc 50m and depositing where directed at a level n exc 50m above the starting point complete all as specified and as directed.

Supply and filling river sand in trenches including spreading for cushioning of LT UG cable complete all as specified and as dirceted. Note : Punned down thickness shall be measured and paid .

M&L for sub class ‘B’ bricks old size laid flat dry in trenches over cable, across the direction of cable complete all as specified & directed .

Supply and fixing in replacemnt of unsv weather proof street light junction box of size 300 x 200 x 105mm including MCB SP 6 Amps and connecting terminals 4 way and fixing with street light poles using necessary MS clamps, nuts, bolts washers, lugs for incoming and out going cables, gland for cable etc of suitable size complete all as specified and as directed. Make : Hensel/Sintex/Universal Switch Gear control Note : The rates quoted shall inclusive of provision and fixing of suitable lugs and glands for cable connection.

Dismantling concrete poles any size complete and transporting and removing from site and making good the disturbed surface incl refilling of soil and making good all as specified and directed. Note- Rate of hydra and lorry is deemed to be included in the quoted rates.

Supplying, transporting to site, erecting & fixing in vertical position, steel tubular swaged and welded poles straight in length of overall height 09 metres, type 410SP-31 , IS-2713 marked complete with CI base plate, taper plug,bolts, nuts, washer and screws etc duly painted internally and externally with metal oxide anti corrosive paint before errection and painting with two coats aluminium paint after erection complete all as confirming to IS 2713 (Part-I to 111) and complete all as specified and as directed. Note: Painting of pole upto 1.5 metre above coping in different colours of alternate equal size of layers with blue and white in colour and marking of Serial No of pole with yellow paint in black circle complete all as specified and directed is deemed to be included in the quoted rates.

Supply and fixing in replacement of unsv LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make- CG/ Havells/ Bajaj

M&L for foundation for tubular swaged pole type including excavation, getting out, pole foundation with PCC type D2 1:4:8 (with 40 mm graded aggregate). Coping of poles with PCC type C1 1:3:6 (with 20 mm graded stone aggregate) and removing surplus soil to a distance n exc 50m and making good surface all as specified and directed by Engr-in-Charge and painting the coping with 2 coat of super enamel paint in two layers of blue and white complete all as specified and as directed.

M&L for PVC flat twin core 4 sqmm aluminium wire 1100 volts grade laid in 20 mm dia medium grade rigid PVC conduit (and fixing brackets on PCC pole) from Loop-in-loop out junction box to light fitting terminal complete all as specified and as directed. Note- PVC conduit shall be clamped properly with suitable clamps and no extra payment will be done on this account.

Supply and jointing in replacement of cold shrinkable straight through joint suitable for LT 1100 volts XLPE cable of size 16 sqmm 3.5 core complete all as specified and as directed

Supply and jointing in replacement of cold shrinkable straight through joint suitable for LT 1100 volts XLPE cable of size 25 sqmm 3.5 core complete all as specified and as directed

Repair/Maintenance of high mast light of any size, oiling of motor of wench, repairing/renewal of burnt out cables, CG box, luminaire and made it functional all as specified and as directed. Note : (i) All unsv Components & parts to be replaced is included in the quoted rates. (ii) If high mast light is stuck in the top, contractor has to arrange the hydra or any m/c required for proper functioning and this is included in the quoted rate. (iii) Only unsv flood light will be paid separately.

Supply and fixed in replacement of integral post top ideal to lit up luminaires energy saving 40 watt LED lamp, with symmetrical light distribution system di-cast aluminium luminairie with high power LED as light source including LED lamp complete all as specified and as directed. Make : Cat pt no LPTO-40-CDL-M of Crompton or equivalent in Havells/Bajaj/polycab. Note: All fixing material is included in the unit rate.

S&F in replacement of Energy saving environment friendly High mast Light with innovative di cast aluminium IP 66 Flood light fitting with 120W LED as light source complete all as specified and as directed Make: Havells/Phillips/Wipro/Crompton Note- Rate of hydra and lorry is deemed to be included in the quoted rates for fixing the light in the high mast.

M & L in replacement for Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.0mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including using galvanised iron strip 25×4mm as earthing strip by means of bolts, nuts, check nuts and washers of galvanized iron or steel, earth plate surrounded by packed layer of char coal dust and common salt, 15cm thick all around bottom and top and watering pipe 20mm bore of GI light grade with funnel, wire mesh and 40 mm dia GI protection pipe medium grade all as shown in electrical plate No 3 of SSR Part-I and connected to earthing test point, main switch board and testing on completion including excavation, earth work concrete pit with 80mm thick RCC cover in RCC 1:2:4 type B-1 duly reinforced with MS bars 8mm dia @ 150C/C both ways and pit chamber in PCC 1:2:4 type B-1 with 2 Nos suitable lifting handles of 12mm MS bar complete all as specified.

Supply and fix GI strip in trenches or wall 32 x 6 mm galvanised iron strip complete all as specified and directed.

akhil enterprises (BID ID -3350458)

Goyal Enterprises (BID ID -3340673)

Nikunj Bansal Govt Contractor (BID ID -3341686)