TNUHDB/14/HD/SE(East -1)/2023

Amount

Labour Charges for providing bored cast – in – situ RCC piles of 500mm dia to the required depth from the existing ground level including boring through ordinary soil other than soft rocks hard stratum and providing arrangements for concreting by termite pipe method as per ISI 2911 excluding the cost of concrete, steel and fabrication of reinforcement in position but including the cost of mobilization charges betonies solution, clearing the removal mud away from the vicinity of the site and hire charges of all other tools and plants and rig required for the work etc., complete in all respect as directed by the Departmental Officers.

Test of single pile under routine load test, test load should be 1590 KN (safe load (1060x1.50) as per the testing inclusive all charges for extension or cutting of pile that may be necessary errecting loading platform in the manner acceptable and approved by departmental officer with labour and other incidental charges for loading and unloading test load and hire charges and all other incidental charges for conducting test including retaining the test load for 24hours at 100% capacity test certificate and calibration charges for pressure gauge are to be produced to the Executive Engineer, Executive Engineer in charge before commencing day of test, calibration of pressure gauge has to be done before taking up the Ist load test in every site of work for piles of 450mm with test load, 1000 KN etc complete in all respects as directed by departmental officers.

Earthwork excavation for foundation with all leads and lifts in all soils and sub soils and to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of 15cm thick well consolidated depositing the surplus earth in places shown and leveling the site with all leads and lifts etc., complete in all respects as directed by the departmental officers.

Filling in foundation and basement with quarry/stone dust in layers not exceeding 15cm thick well watered rammed and consolidated complying with relevant specification including the cost of supplying stone dust etc complete in all respects as directed by the departmental officers.

Filling in foundation and basement with M Sand in layers not exceeding 15cm thick well watered rammed and consolidated complying with relevant specification including the cost of M.Sand etc complete in all respects as directed by the departmental officers

Cement concrete 1:4:8 (one of cement, four of M-sand and eight of hard broken stone) using 40mm size hard broken stone inclusive of shoring, strutting, bailing out water, ramming, curing, etc complete in all respect as directed by the departmental officers

Providing and laying in position, Standardized Concrete Mix (RMC) M-30 Grade in accordance with IS 456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kglms and maximum water cement ratio of 0.45, including admixture (plasticiser super plasticiser) recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg of M-Sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying. vibrating with mechanical vibrators, finishing. curing. etc. and providing fixtures like fan clamps in the RCC floor roof slabs wherever necessary without claiming extra, etc complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards and as per the design mix. (No separate payment will be made by the Department for the excess usage of materials). For all Floors.

Providing form work for centering, shuttering etc., for all reinforced concrete work as plinth beam, raft beam, raft slab, grade beam etc., including shuttering, 3.00mm high using MS sheet of size 90cm x 60cm and BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joists of size 10cm x 6.5 cm (Spaced about 91cm center to center) distance and supported by casurina props of size 10cm-13cm dia (spaced at 75 cm center to center) and removing the same after a specified period without damaging RCC works in all floors etc., complete as directed by the departmental officer Grade beam/plinth beam

Providing form work for centering, shuttering etc., for all reinforced concrete work like slab, beams, lintels, loft etc., including shuttering, upto 3.00m high using MS sheet of size 90cm x 60cm and BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joists of size 10cm x 6.5 cm (Spaced about 91cm center to center) distance and supported by casurina props of size 10cm-13cm dia (spaced at 75 cm center to center) and removing the same after a specified period without damaging RCC works in all floors etc., complete in all respects as directed by the departmental officer. (For Slabs, Lintels & Lofts)

Providing form work for centering, shuttering etc., for all reinforced concrete work like lintels, window boxing etc., including shuttering, upto 3.00mm high using MS sheet of size 90cm x 60cm and BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joists of size 10cm x 6.5 cm (Spaced about 91cm center to center) distance and supported by casurina props of size 10cm-13cm dia (spaced at 75 cm center to center) and removing the same after a specified period without damaging RCC works in all floors etc.,complete as directed by the departmentalofficer.Sunshade, window boxing, column

Fabricating and placing the steel grills of Fe 500 D grade Corrosion Resistance Steel bars (CRS) reinforcement bars as per relevant IS code for all reinforced cement concrete works such as plinth beam, lintels, beams, sunshade, roof and floor slabs etc., including cost of steel and fabricating the reinforcement grills in position etc., complete in all floors (The rate to include the cost of binding wire steel also)

Brickwork in cement mortar 1:5 (One of cement and five of M-sand) using Fly ash bricks of size 9" x 4 3/8" x 2 3/4" for super structure in the following floors including fixing the frames of doors and windows scaffolding, proper setting curing etc., complete etc complete in all respect as directed by the departmental officers

Foundation and Basement

Masonry work using AAC Blocks (Auto Claved Aerated Concrete Blocks) in Cement Mortar 1:6 (One of cement Six of M-sand) of size 600mm X 200mm X 200mm for superstructure in the following floors including fixing the frames of doors and windows scaffolding, proper setting curing etc., complete in all respect as directed by the departmental officers.

In Groundfloor

In First floor

In Second floor

In Third floor

In fourth floor

In Fifth floor

In Sixth floor

In Seventh Floor

In Eighth Floor

In Ninth Floor

In Tenth Floor (Terrace Floor)

Masonry work using AAC Blocks (Auto Claved Aerated Concrete Blocks) in Cement Mortar 1:5 (One of cement Five of M-sand) of size 600mm X 200mm X 100mm for superstructure in the following floors including fixing the frames of doors and windows scaffolding, proper setting curing etc., complete in all respect as directed by the departmental officers

In First floor

In Second floor

In Third floor

In fourth floor

In Fifth floor

In sixth floor

In Seventh Floor

In Eighth Floor

In Ninth Floor

Brickwork in cement mortar 1:6 (One of cement and six of M-sand) using Fly ash bricks of size 9" x 4 3/8" x 2 3/4" for super structure in the following floors including fixing the frames of doors and windows scaffolding, proper setting curing etc., complete etc complete in all respect as directed by the departmental officers

In Groundfloor

In First floor

In Second floor

In Third floor

In fourth floor

In Fifth floor

In Sixth floor

In Seventh Floor

In Eighth Floor

In Ninth Floor

In Tenth Floor (Terrace Floor)

Providing 7.5 cm thick staircase parapet wall using Fly ash bricks of size 9"x4 3/8"x2" 3/4" in cement mortar 1:4 (One of cement and four of sand) and plastering the hand rails portion only with red oxide plastering in cement mortar 1:4 (one of cement and four of sand) 20 mm thick using 9.8kg of redoxide powder per 100 Sq.m and plastering either side of parapet with CM 1:4 (One of cement and four of sand) 20mm thick providing skirting, finishing smooth complete in all respects in all floors

Supply and fixing the both side polished cuddapah slab for cup board planks of size required, 20mm thick as directed by the departmental officers in all the floors etc., including fixing in position finishing curing etc., complete in all respects as directed by the departmental officers

Providing Ellis Pattern flooring 20mm thick (Ellis pattern) with layer of cement concrete 1:3 (one of cement and three of hard broken stone) (No sand) using hard blue granite chips of size 3mm to 10mm and surface rendered smooth over RCC slab and staircase landing slab including supplying and fixing 20mm dia GI pipe outlet etc., complete in all respect as directed by the departmental officers.

Plastering the walls with cement mortar 1:4, (One of cement and five of P-sand) 20mm thick including finishing smooth, scaffolding, setting, cornice, curing etc., complete as directed by the departmental officers

Plastering the walls with cement mortar 1:3, (One of cement and three of P-sand) 20mm thick with necessary water proofing compound at the rate of 1.06 kg /10 m2 including finishing smooth, scaffolding, setting, cornice, curing etc., complete as directed by the departmental officers

Cement Concrete 1:5:12.5 ( one of cement five of M-sand and twelve and half of broken brick jelly) using 20mm size for plain cement concrete including curing finishing etc., complete in all respects as directed by the departmental officers.

Supplying and fixing of factory made PVC rigid panel door with frame made from MS tubes of 19 gauge size of 19mm x 19mm and covered with heat moulded PVC channel of 5mm thick and width of 50mm to from styles and rails. The inner pannel should be inserted between the frame with 6mm thick PVC rigid foam sheet welded/sealed to the style and rail along with 5mm x 25mm PVC beading on all and their sides. The vertical tube may be filled with suitable materials to furthere enhance the screw holding capacity etc.m complete in all respects and colour as directed by the departmental officers Door Size 0.75 x 2.1 m.. size 750X 2100mm

Special ceiling plastering for all RCC works in cement mortar 1:3 (One of cement and three of P-Sand) 10mm thick including hacking the RCC surface, providing necessary water band using the same mix of mortar wherever necessary proper finishing, curing, scaffolding etc., complete with relevant standard specification, complete in all respect as directed by the departmental officer.

Plastering the walls with cement mortar 1:5, (One of cement and five of P-sand) 12mm thick including finishing smooth, scaffolding, setting, cornice, curing etc., complete as directed by the departmental officers

White washing two coats using clean shell lime including the cost of lime, gum, brushes and scaffolding etc., complete in all respects as directed by the departmental officers

Painting the walls with two coats of newly plastered wall surface with ready mixed exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, including necessary cement base putty, wherever required etc., paint brushes with scaffolding and labour charges etc., complete in all respect as directed by the departmental officers

Painting the new wood works with two coat of first class ready mixed synthetic enamel paint of approved quality and colour over one coat of priming including the cost of paint brushes and scaffolding etc., complete as directed by the departmental officers.

Painting the new iron works of doors with one coat of first class synthetic enamel paint of approved quality and colour including the cost of paint brushes and scaffolding etc., complete as directed by the departmental officers

Supplying and fixing in Position White Colour Glazed model European water closet of best quality and approved make with 100mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinge including cost of white cement for packing, spun yarn, teak wood plug brass screws, etc., including supplying and fixing 10 liters capacity PVC/ 12.5 liters capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fitting, such as, 15mm brass ball valve with polythene float with brass handle union coupling connected by means of 40mm White PVC flush hand using indian adopter joint including all internal fitting, such as, 15mm bras connections 15mm GM wheel valve .15mm bras nipple (2 nos), 15mm nylon connections,TW plugs, screws and also giving necessary connection to the PVC pipe and nainting the CI brackets with 2 coats of approved paint over one coat of red oxide paint etc., complete in all respects as directed by the departmental officers..

Supplying and fixing of Oriya type water closet 45cm with 'P' or 'S' trap (White glazed) earthen ware best (IN ALL FLOORS OTHER THAN GROUND FLOOR) including concrete packing fixing filling the sink portion with stone jelly lime concrete 32:12 1/2 (Thirty two parts of broken stone jelly and twelve and half of lime (no sand) using 20mm size broken stone jelly and plastering the top of flooring with cement mortar 1:4 (one of cement and four of sand) 12mm thick including plastering the sides of sink portion in cement mortar 1:3 (One of cement and three of sand) 12mm thick mixed with water proofing compound 4 lbs/cft in cement applying one coat of britex solution including curing for the sides and bottom of the sink portion, curing etc., complete in all respects as directed by the departmental officers..

Supplying and fixing PVC Nahini trap / Floor Trap with PVC grating 100mmx75mm over the bed of brick jelly concrete and fixing in position etc., complete in all respect as directed by departmental officers.

Supplying of Door Frame of overall Size 1000 mm x 2100mm with required dimensions of size~ 100 mm x 75 mm, with groove of size ~ 30 mm x 20 mm for resting the door shutter & chamfer finish at front using CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames including providing holes and fixing wooden blocks for fixing fixtures and fittings and 4 nos of hold fast using the iron angle of 15cm length with split ends one coat of redoxide primer / Chemical arcylic, Fabrication and Supply of 35mm thick solid core flush door with teakply on one side and commercial ply on other side with teak wood lipingalround with iron oxidised hinges ,tower bolts 12" 2 nos with receiver, Aldrop 30 cm and handle 1 no for door of size 1000mm X 2100mm

Supplying of Door Frame of overall Size 1000 mm x 2100mm with required dimensions of size~ 100 mm x 75 mm, with groove of size ~ 30 mm x 20 mm for resting the door shutter & chamfer finish at front using CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames including providing holes and fixing wooden blocks for fixing fixtures and fittings and 4 nos of hold fast using the iron angle of 15cm length with split ends one coat of redoxide primer / Chemical arcylic, Fabrication and Supply of 35mm thick solid core flush door with teakply on one side and commercial ply on other side with teak wood lipingalround with iron oxidised hinges ,tower bolts 12" 2 nos with receiver, Aldrop 30 cm and handle 1 no for door of size 0.91mx2100mm

Supplying and Erecting Pull and Push TypeRollingShutter with ISI make of approved size and sectionusing 18 GI sheet. The shutter shall be painted withone coat of red oxide primer and the rate is inclusive ofhood covers, transportation charges etc., complete in all respect as directed by departmental officers.

Supplying and fixing of 300mm (12") sweep (Heavy Duty) AC Exhaust fan complete without provision of hole in the wall etc., complete in all respect as directed by the departmental officers

Supplying and fixing of UPVC (unPlasticised Polyvinyl Chloride) Casement / Openable / Fixed windows made out of upvc profile section of size 74mm x 60mm as outer frame having outer wall thickness of 2.3mm (+/-0.3mm) and 3 box multi-champers hollow construction. the shutter of openable window shall be made of size 74mm x 50mm having outer wall thickness of 2.3mm (+/-0.3mm) with a fixed mullion of size 72mm x 60mm having outer wall thickness of 2.3mm (+/-0.3mm). All section of frames, sash and mullion shall be reinforced, wherever required and at the hardware fixing location with galvanized mild steel section of 1.2mm thick. All the corners / mullion joints of the frame & sash shall be mitered cut and fusion welded without any mechanical joining. Window Size 1.20mx1.20m

Supplying and fixing UPVC (un-plasticized polyvinyl cholride) Louvered ventilators of from the profile the size of ouetr frame 60mm x 58mm and shutters profile size of 60 x78mm both profile are reinforced with GI/1mm 125GSM and 100% corrosion free the, profile are multi chamber section with wallthick of 2.0mm. The EPDM rubber ( Blackcolour ) covered with all over the edges of frame and shutter.The corner and the joints should be welded and cleaned. Radiations pin headed glass 4.0mm thick should be provided in the louveres . The window should be fixed to the wall with 100% packing with screws and silicon packing alround the frames.The ventilator should be got approved from the Executive Engineer before the use on the work for window of size .60 m X .60 m

Weathering course in concrete broken brick jelly 20mm size in pure slacked lime over RCC roof slab the proportion being 32:12 1/2 (Thirty two parts of broken brick jelly and twelve and half of slacked lime) laying to a thickness of 110mm and compacted and well beaten to 80mm by using wooden hand beaten of weight not exceeding 2 kg hand beating during liberally with lime water and a small proportion of solution prepared by soaking water in dry nut of kadukka and giving required slope and thickness of roof etc. as directed by the departmental officers.

Finishing the top of roof slab with one course of pressed tiles 23cm x 23cm x 20cm using cement mortar 1:3 (One of cement and three of P-sand) mixed with water proofing compound at 2% weight of the cement and pointed with the same l mortar etc., complete in all respects.

Supplying and fixing of 110mm dia PVC soil pipe of 6kg / cm2 of approved quality confirming to IsI13592/1992 with ISI Monogram packing the joints with hemp yarn and cement including fixing into walls with necessary wooden plugs and holding down clamps, dismantling and making good of the dismantled portion with necessary connection to the sanitary fittings painted with two coats of anti-corrosive paint including testing etc., complete in all respects. Vertical line

Supplying and fixing of 75 mm dia PVC soil pipe of 6kg / cm2 of approved quality confirming to ISI 13592/1992 with IsI monogram packing the joints with hemp yarn and cement including fixing into walls with necessary wooden plugs and holding down clamps, dismantling and making good of the dismantled portion with necessary connection to the sanitary fittings painted with two coats of anti-corrosive paint including testing etc., complete in all respects as directed by the departmental officer. Vertical line

Supplying and fixing of 110mm dia PVC soil pipe of 6kg / cm2 of approved quality confirming to IsI13592/1992 with ISI Monogram packing the joints with hemp yarn and cement including fixing into walls with necessary wooden plugs and holding down clamps, dismantling and making good of the dismantled portion with necessary connection to the sanitary fittings painted with two coats of anti-corrosive paint including testing etc., complete in all respects as directed by the departmental officers. Horizontal line

Supplying and fixing of 75 mm dia PVC soil pipe of 6kg / cm2 of approved quality confirming to ISI 13592/1992 with IsI monogram packing the joints with hemp yarn and cement including fixing into dismantling and making good of the dismantled portion with necessary connection to the sanitary fittings painted with two coats of anti-corrosive paint including testing etc., complete in all respects.

Supplying and fixing of 110mm dia PVC rain water down fall pipe 4kg/cm2 with 2 nos of PVC bend & pipes with necessary clamps couplers gratings, teak wood plug etc., complete including fixing in proper position with solvent cement etc., including making good of the dismantled portion complete to the relevant std specifications etc., complete in all respects as directed by the departmental officers

Supplying of PVC pipe specials of approved quality suitable to pipe as per table II IS 14735/1999

110mm dia PVC vent Shoe

110mm dia PVC vent Cowl

75mm dia PVC vent shoe

75mm dia PVC vent Cowl

110mm dia PVC single “T “with door

75mm dia PVC single “T “with door

Construction of Inspection chamber 0.60M x 0.60M for the following depth brick jelly cement concrete 1:5:12 1/2 (One of cement and five of M- and twelve and half of broken brick jelly) using 40mm size brick jelly 15cm thick for foundation 23cm thick Fly Ash brick masonry wall in CM 1:5 (One of cement and five of M-sand) using Fly Ash bricks of size 23x11x7cm and inside plastering with 1:3 (one of cement and three of P-sand) 12mm thick including channeling, benching etc. and top covered with SFRC (medium duty) cover slab and fixing in position and necessary earth work excavation, refilling the sides of foundation in all soils except hard rock requiring blasting etc. complete in all respects as directed by the departmental officers. (Average Depth of .60m)

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works as per IS 4985

50mm diapvc pipe

40mm diapvc pipe

32mm pvc pipe

20mm pvc pipe

Supply of G1 pipes and ISS 1239 (medium) screwed at both ends and socketed both ends and complete in all respects as directed by the departmental officers 40mm dia GI pipe inlet

63mm dia GI pipe at inlet

Labour charges for cutting and jointing the GI ngid pipes using solvent cement required with necessary specials of the following dia above ground level including fixing to wall with necessary teak wood plugs, clamps and screws making holes in the wall or drilling holes in the roof making packed the same with necessary brick work and plastering wherever necessary painting etc., with necessary scaffolding etc.

63 mm diaGl pipe @ inlet

Supplying and fixing GI & GM wheel valve of approved quality complete in all respect as directed by departmental officers.

50mm dia GI Elbow

65mmx50mm dia Reducer

50mm GM wheel valve

20mm GM wheel valve

Supplying the following dia UPVC specials of approved quality confirming to IS4985/1988 and fittings of size as follows

20mm dia UPVC Elbow

20mm dia UPVC Tee

25mmX 20mm dia UPVC Threaded reducer

15mm dia screw down tap heavy type

40mm threaded Nipple Connection with flange set

50mm dia UPVC Coupler

50mm dia UPVC Elbow

50mm dia UPVC Tee

40mmX 32mm dia reducer

32mm dia Tee

32mm dia Elbow

32mm dia Coupler

32mm x 20mm dia UPVC reducer

Supplying and fixing stainless steel Sink of size 600mm x 450mm x 230 mm with 23mm dia 'B' Class G.I. waste water pipe & 32mm dia C.P. waste coupling etc., complete in all respects as directed by the departmental officers.

Dadooing of the walls with first quality Glazed tiles of size 150mm x150mm x 6mm of approved quality laid in cement mortar 1:2 (One of Cement and two of M Sand), 10mm thick and pointing with white cement neatly as directed by the departmental officers etc., all complete .

Flooring with ceramic tiles of approved quality, colour and design anti skid type joint free of size 305mm x 305mm x 6mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one of cement three of M-Sand) 20mm thick and laid straight alignment and pointed neatly with colour cement @ 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specification and as directed by the departmental officers.

Fabricating, supplying and fixing of M.S. safety steel grills for Balcony parapet ,Corridor end parapet, Staircase mid landing parapet and corridor duct parapet including one coat of primer with red oxide of good quality etc., Complete in all respects as directed by the departmental officers

Supply and run off 2 of 2.50sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark confirming to IS:694/1990 with continuous earth connection by means of 1.50 sqmm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable UPVC rigid pipe 1.8mm thick concealed in wall for mains including the cost of UPVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departmental officers.

Wiring with 2x1.5sqmm UPVC insulated single core unsheathed copper conductor cable of 1100V grade with ISI mark confirming to IS: 694/1990 in suitable UPVC rigid pipe of 1.8mm thick with ISI mark concealed in wall and ceiling with UPVC accessories in flush with wall including the cost of cable, UPVC pipe and specials, ceiling rose, flush type 5ams SP mark switch, UPVC junction box, 16gauge MS switch box 100mm x 100mm x 75mm covered by laminated hylem sheet 3mm thick, cement, labour and making good of concealed portion with suitable colour for concealed light point..

Wiring with 2x1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100V grade with ISI mark confirming to IS 694/1990 in suitable PVC rigid pipe of 1.8mm thick with ISI mark concealed in wall and ceiling with PVC accessories in flush with wall including the cost of cable, pvc pipe and specials, ceiling rose, flush type 5ams SP mark switch, PVC junction box, 16gauge MS switch box 100mm x 100mm x 75mm covered by laminated hylem sheet 3mm thick, cement, labour and making good of concealed portion with suitable colour for concealed etc. complete as directed by the departmental officers.

Wiring with 2x1.5sqmm UPVC insulated SC unsheated CU conductor of 1100 V grade with ISI mark confirming to IS: 694/1990 in suitable UPVC rigid pipe of 1.8mm thick with ISI mark concealed in wall and ceiling with UPVC accessories in flush with wall for 5 AMPS 3 PIN C.S. PLUG POINT AT CONVENIENT PLACES including the cost of cable, UPVC pipes and specials, brass screws, flush type 5 amps 3 Pin C.S. plug, 16 gauge Msjoint box, 16 gauge MS switch box covered by laminated hylem sheet 3mm thick, cement, labour and making good of the concealed portion with suitable colour for concealed UPVC plug point.

Supplying and fixing of 5 A /15A 3 pin flush type wall socket with15A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet including cost of wall socket, switch and labour charges fo wall cutting, grouting, flushing and making good, painting with primary and finishing coat for MS box etc., complete as directed by the departmental officers.

Wiring with 2 x1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100V grade with ISI mark insuitable PVC rigid pipe 2mm thick concealed for FOR 5 AMPS 3 PIN C.S.PLUG POINT AT SWITCH BOARD ITSELF including cost of cables, PVC pipe and special, brass screws, flush type Samp S.P.Mark switch, labour and making good of the concealed portion with suitable colour for concealed PVC plug point.

Supplying and fixing of 8 way single phase DB of 16amps/way with 16amps DP switch with metal glad of 500 volt(side handle) with Fuse and Neutral of suitable T.W. Board of size 40cm x30cmx6.3cm with earth connection etc., complete in all respects as directed by the departmental officers

Earthing as per the ISI specification with an earth electrode of 2.1 mtr class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 40mm RCC cover / CI cover slab for the brick masonry etc., complete in all respects as directed by the departmental officers

Supplying and run off 8 SWG copper wire on walls or below ground level with necessary 'U' nails, earth work excavation and refilling & including the cost of all materials etc., complete in all respects as directed by the departmental officers

Providing Ellis Pattern flooring 20mm thick (Ellis pattern) with layer of cement concrete 1:3 (one of cement and three of hard broken stone) (No sand) using hard blue granite chips of size 3mm to 10mm and surface rendered smooth over RCC slab and staircase landing slab including supplying and fixing 20mm dia GI pipe outlet etc., complete in all respects.

Supply and Fixing of Stoneware gully chamber etc.,complete in all respects as directed by the departmental officers.

Sectioning the site including cutting and filling the undulations upto 15cm thick and leveling etc, complete in all respects as directed by the departmental officers

Filling in foundation and basement with Gravel in layers not exceeding 15 cms thick well watered rammed and consolidated complying with relevant standard specification including the cost of supplying M-Sand etc., complete in all respects as directed by the departmental officers.

Plain Cement concrete 1:2:4( one of cement , two of sand and four of hard broken stone jelly) using 20mm size hard broken stone jelly for foundation and basement inclusive of shoring, strutting, bailing out water wherever necessary, ramming, laying vibrating and curing proper setting etc, all complete as directed by the departmental officers.

Providing through vertical joints, with 15mm space filled with Bitumen felt 2mm thick pad running from bottom of foundation upto the top etc., complete in all respects as directed by the departmental officer

Supplying and laying of 160mm dia UPVC non pressure pipes as per IS 15328/2003 [SN8- SDR(S 16.5)] and laying and jointing of UPVC pipes to the proper grade and alignment as indicated in drawing / design and hydraulically testing of the pipe line. The rate shall include cost of all necessary jointing materials testing charges with water conveyed within a lead of 1km, labour etc., complete in all respects as directed by the departmental officer

Manufacturing supplying and laying the Rubber Moulded Hydraulic Pressed Paver Blocks of 63mm thick of require size and approved design in colour over the bed of Quarry Dust filling & beneath layers including labour for layin, hand packing and compacting with necessary power rammer machine layer and finish with watering filling with Quarry Dust wherever required for proper compaction, alignment and gradient etc., complete in all respects as directed by the departmental Officers.

Cement concrete 1:3:6 (One of cement, Three of M sand and six of hard broken stone) using 20mm size hard broken granite broken stone inclusive of shoring, strutting, bailing out water, ramming, finishing, curing etc., complete in all respect as directed by the departmental officer.

Paiting the walls with two coat of approved good quality of cement paint such as snow cement &supercem including the cost of paint, brush, scaffolding and watering etc., complete and as directed by the Engineer,

Open earth work excavation for foundation with all leads and lifts in all soils and sub soils to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of 15 cm thickness well consolidated depositing the surplus earth in places shown and leveling the site with all initial leads and lifts etc complete in all respects as directed by the departmental officers.

With initial lead of 10m and initial lift of 2 M

With initial lead of 10m and additional lift of 1 M

With initial lead of 10m and additional lift of 2 M

Supplying and fixing 100mm dia CI ventilating pipe of 0.50 m length with cowl complete in all respects as directed by the departmental officer

supplying & fixing SFRC Manhole frame and cover slab of following size of best approved quality 0.60 x 0.60 x 30 Kgs. ( heavy ) etc., complete in all respects as directed by the departmental officer.

supplying & fixing fibre modan shear steps @ 30cm c/c inside sump from ottam to top of slab etc., complete in all respects as directed by the departmental officer.

Added GST of 18% (All Items)