Design Supply Erection Fabrication Testing and Commissioning of Cold Store of size 6m x 10m x 3.5m

Amount

Earthwork in excavation by manual means over area for leveling purpose including disposal of excavated earth up to 1m from cutting edge and should be disposed in near-by all kind of soil Plinth work for Store = 688 Cft Plinth work for CGI Shed = 240 Cft Floor area = 760 Cft Total = 1688 Cft = 47.79 Cum Area to be excavated keeping in view the earth quake resistance for which a MS mesh(10 mm) is to be provided in the base foundation of the plinth

Providing and laying of cement concrete (1:5:10) using 40mm nominal size nallah stone. Qty = 13.22 Cum

Centering and shuttering including strutting, propping etc. and removal of form work for: 4.6.1 Foundations, footings, bases for columns Quantity = 129.32 Sqm

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead up to 50m and lift up to 1.5m. Qty = 16.48 Cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Mild steel and medium tensile steel bars 10mm bar for Plinth Tie beam Cold Store = 203.10 Kg 10mm bar for Plinth Tie beam CGI Shed = 73.34Kg 8mm bar for Plinth Tie beam Rings for Cold Store and CGI Shed = 530.94 Kg 10mm bar for Floor Raft Cold Store and CGI Shed = 571.70 Kg Total = 1379.08 Kg

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand) Qty = 0.301 Cum

12 mm cement plaster to plinth wall of mix 1: 4 (1 cement: 4 fine sand) for water tank walls, tank flooring and RCC plinth 1’ of Mushroom unit AGL. Qty = 22.96 Sqm

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size Plinth = 1044 Cft Rafts = 350 Cft Total = 1394 Cft = 39.47 Cum

Structural Steel work welded in built up section/framed work including cutting, hosting, applying a priming coat using structural steel. In gratings, frames, guard bard, ladders, railings etc. 6 No. of trusses including primer and enamel paint including nut bolts, kingpost, struts etc. Column Rectangular Hollow Pipe Section(80x40x2mm) COLD STORE Columns, Tie and Cross Members CGI Canopy for rain water protection Truss Vertical Members , Truss Inclined Members, Truss Tie Members CGI Shed for Electrical Installations Columns, Tie Members TOTAL = 1631.21Kg

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern. over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer- in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. Area = 47.93 Sqm

Carriage of Sand aggregate below 40 mm, Carriage of Bazri aggregate 40 mm nominal size and above, Carriage of Steel, Carriage of Cement and carriage of other allied material By Mechanical Transport including loading, unloading and stacking beyond 10 km upto 20 km per km

Racks for Apple Saplings :- Providing of Slotted Angle Metal Storage Racks of size 84”H x 23”L x 18”D - 22 Gauge, 16 Gauge Angle with7 Shelves for storage and display of Wool items in the display rooms of the wool centre. Job is inclusive of the cost of material, transportation and all taxes etc.

Supply, installation and Commissioning at site of Prefabricated PUF (Poly-Urethane Foam) Panels of size 80 mm thick Fire proof Panels for walls (PPGI finish on both sides), Ceiling Roof and Floor to make a closed structure on the outer frame. Prefabricated Sandwich PUF panels with Cam toggle type fasteners fitted and self-locking PVC gaskets fitted on all sides of wall and ceiling/roof including rivets, Silicones, Anchor fastener, self-drilling screw and all other allied accessories required for the installation/erection of PUF panels. The Panel Thickness and density should be 80mm/40+/-2Kg/Cum. Floor Type should be 80mm bare PUF with Bitumen tarfelt finished with KOTA Stone and Panel type be PPGI on the both side and Wall to wall cam locking system. Internal/External flashing to be provided. Temperature required in the room is 2˚C +/- 8˚C Qty = 488.13 Sqm

Supply, installation and Commissioning at site of Prefabricated PUF (Poly-Urethane Foam) Panels Heavy Duty Swing Type Flush Door for Cold Room of size 34’’x78’’ with PPGi outside and Inside equipped with heavy duty hinge & lock and sweep gasket. Door lock from outside, automatic door closer and other allied accessories. Heavy duty cast alloy handles with heavy duty hinges with chrome finish. Air right heavy duty sealing gasket below door with double sweep, posi seal closure cushions closing of door. Safety release knob to be provided from inside the door with PVC Strip Curtain Job includes the cost of material, transportation, labour cost and all taxes

Refrigeration Unit:-SITC of refrigerant unit of capacity 36000 BTU/Hr(420V/3Ph/50Hz) (5TR) for maintaining a temperature of 2˚C +/- 8˚C (or as per requirement of end user) around the year. The unit shall comprise of four machines one working and one standby in each chambers ( 2 Nos) with following features. a. Indoor unit (04 Nos) Evaporator Cubical type, of capacity 36000 BTU/Hr, Evaporator size: 2215x565x616mm, Fans- 03 Nos., Total air Flow: 12121 CMH, Fan Power: 555Watts (03x185). b. Outdoor unit (04Nos) Hermit Recip Compressor to be sealed heavy duty air cooled with low noise level and minimal vibration. MOC should be GI powder coated. Filter dryer can be internal/external. Cooling Capacity 7.3KW/set at 0 Degree. C Evap. & 50 Deg C Condensing. Size: 975x400x82mm, Total air flow; 5100 CMH, Fan Power 107 Watts (01x107). c. R407a/R22 refrigerant or any other equivalent as per OEM design. d. Control panel should have microprocessor based digital temperature controller/humidity controller cum indicator for easy readability with following features. i.It should protect device from single phasing, voltage unbalance, phase reversal and under/over voltage. ii. It should also show real time voltage between phase and neutral. iii. It should shut down the system in case of fault from pressure control/similar device. iv. It should have safety controls such as delay at start up and minimal disable time to protect compressor from close start. The job includes complete installation of refrigeration system with suitable MS Stands for Outdoor units, Constant Voltage Stabilizer for operation of machines and fitment of digital controller along with copper pipes, tees/elbows/reducers brazing charges and tools and tackles required for the execution of the job.

Fresh air Damper /Blower/ Ducts/Plenum:-Supply and installation of air mixing chamber inside the cultivation room, Aluminum Damper for CO2 exhaust, fresh air damper system and return air as per site requirement. The Job includes SITC of blowers of requisite specifications as per OEM design along with all allied accessories. The job also includes providing/ fitting of Elbow Duct with Air filters for fresh air inlet and CO2 exhaust outside the plant along with installation of air plenum duct/air tight cloth duct with evaporator and poly duct inside the room for air distribution. It also includes fresh air dampers in the packing room along with pre filters for protection against insects and dust as and where required. Job includes the cost of material, transportation, labour cost and all taxes.

Supply, Installation, Testing and Commissioning of Automatic Controller & Sensor based Controlling Humidifier with humidity range from ambient to 85% controlled by digital humidifier indicator cum controller 24x7 hours working, humidification capacity of 6-8 litres/hr and capable of generating high RH levels upto 90%. Job includes the cost of material, transportation, labour cost and all taxes.

Electrical fittings: - The job includes electric fittings along with embedding of PVC conduits in the walls with multi stranded electric cables with switch boxes and switch boards/Sockets/Switches/MCB’s of requisite amperage suitable for Refrigeration system, Stabilizer, Blowers, Humidifier, Vapor proof LED Lights, LED flood lights of suitable watts inside and outside the cold store and Electrical installations CGI shed. Complete job includes cost of material and labour charges for the execution of job.

Providing/Fabrication of Mobile Structural Steel Library type ladder/stairs with platform of size 2’x2’ and height of ladder from ground upto platform deck 7’ fabricated out MS pipes and angle of suitable size duly primed and painted as

Providing and Fitting of 50KVA Three Phase Oil Cooled Servo Stabilizer (AVR) of standard Make with microprocessor based control system, 100% copper wound, overload and short circuit protection, automatic shutdown in case of fault, output voltage 415V+/-1% under unstable voltage conditions. AVR to cover overhead by CGI Sheets. Job also includes the earthing of AVR with 04 sets of earthing i.e. 2 for neutral & 2 for body. job includes cost of material and labour charges and all taxes for the execution of job

SITC of silent type Diesel Generator set of 40 KVA prime rating, 415 volts at 1500 RPM, 0.8 lagging power factor suitable for 50 Hz ± 3%, three phase system & for 0.85 load factor with CPCB sound proof acoustics enclosure fabricated out of 14/16 SWG CRCA Sheet, cooling, fuel, exhaust intake air, fuel, lube oil & governing systems etc., Synchronous alternator 40KVA, with proper starting & shut down arrangement, Base frame & RCC Foundation, Engine Protection and Alarms for low lube pressure, high water Temp, high/low Dc Voltage, weak battery, over speed, fail to crank, fail to start, sensor failure, Battery charger, Acoustic Enclosure, Automatic Mains Failure (AMF) Panel (40 KVA) with all automatic controls, HRC fuses, contactors 100A – 2 nos one each for mains and DG Set, indicating warning lamps, 04 sets of earthing i.e. 2 for neutral & 2 for body, PVC/XLPE Al power Cables (1.1 KV grade armored cable Sq mm of 3.5 core – 30 mtr). DG Set to covered overhead by CGI Sheets.

Job charges for priming and painting structural steel parts of the cold store and CGI shed by applying two coats of superior quality red oxide primer and two coats of anti-corrosive paint. Job also includes providing and fixing of Flex board of size 10’x3’ indicating the name and specifications of the cold store fixed in front of the cold store. Complete job includes cost of material and labour charges and all taxe for the execution of job.

Job charges for laying of KOTA Stone of superior quality inside the cold store including the cost of Kota stone fixing, grinding and polishing. Complete job includes cost of material and labour charges and all taxes for the execution of job. Qty = 1320 Sft

Providing and fixing 0.50 mm pre-profiled colour coated corrugated sheets to laid over frame work of trusses columns, purlins and side rails using hot dipped zinc coated self-drilling hexagonal washers, fastener etc. Roof: Total area = 163.50 Sqm

deepairconditioning

kuldeep singh

HITECH ASSOCIATES