GE (N) P/TOKEN- 52 OF 2021-2022REPAIRS TO CEILING, PLUMBING, PERIODICAL SERVICES, PATH AND FINISHES IN PCDA(SC), CHITRAGUPTA COLONEY AND CERTAIN AREA UNDER AGE B/R (CENTRAL) UNDER GE (N) PUNE.

Amount

Taking down door and refixing shutters in the same opening after making necessary repair of any description exc 1.0 Sqm nut not exc 2.0 Sqm each.( Note :- Builders hardware used in repairs shall to measured separately)

Taking down chowkats or frames with shutters not exc. 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkats or frames with shutters exc. 1.5 Sqm but not.exc 4 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

Taking down shutter from frame of any description exc 1.00 Sqm but not exceeding 2.00 Sq.m each complete all as specified and directed. (a)

S&F factory made 100% solid wood plastic composite (WPC) door frame, single rivet 90 mm x 45 mm made from wood plastic composite (Single extruded process) material with density 780 Kg/ Cum complete all as specified and directed.NOTE: During fixing of chowkhat, surface shall be Made good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement. Make: Rajshri/ Sintex/Duraplast/Accucell

Supply and fix for 35 mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including 30mmx 4mm thick 2nd class hard wood plain cover fillets on all sides complete all as specified and directed.

Supply and fix for factory made solid Panel PVC door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail, bottom rail; panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90°) and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified and as directed. Make: Rajshri/ Sintex/Duraplast/Accucell

Factory made solid panel gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling shall be of wire gauze of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.4 mm . The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S.tubes. The wire gauge shall be stretched to tighten firmlyplain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing Make: Rajshri/ Sintex/Duraplast/Accucell

S&F in repair Capsule type automatic door closure stainless body 150mm long of make Godrej or equivalent

S&F Stainless steel butt hinges medium weight 100mm with all as specified and directed. NOTE :- All screws shall be self tapping chrome plated and length of screw not less 38 mm complete all as specified and as directed

M&L for double charged vitrified ceremic tiles 10 mm thick (square/rectangular) polished, area of each tile exc. 0.18 sqm not exceeding 0.36 sqm, in flooring etc , laid over and including screed bed of 15 mm thick cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match dark shade including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for double charged Vitrified ceremic tiles 10mm thick of approved shade as in vertical surfaces, skirting etc , set and jointed in neat cement slurry and pointed in white or coloured cement to match dark shade over and including rendering of 10mm thick in +cement mortar 1:3 including dismantling existing tiling, cement mortar rendering (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in sub base including demolition of existing PCC 0f subbase/ sunken floor and removing rubbish off the premises complete all as specified and directed.

M&L for 20 to 25mm thick coloured Glossy Chequered cement concrete tiles of area exc. 0.08 Sqm and n.exc 0.16 sqm each, set, jointed and pointed in net cement slurry mixed with grey cement and pigment in floors including 15 mm thick screed bed or bedding layer of cement mortar(1:6) for laying floor finishes including dismentling existing tiles complete all as specified and as directed.

M&L for Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including screed bed of 15 mm thick cement mortar 1:4 including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for Glazed coloured ceramic tiles in vertical surface 300mmx200mmx7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including rendering of 10 mm thick in cement mortar 1:3 including dismantling existing tiling, cement mortar rendering (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 600mm x 300mm x 7 to 8mm thick of colour and pattern as approved by GE, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick rendering in cement mortar 1:3 including dismantling existing tiling, cement mortar rendering (but not backing), removing rubbish off the premisescomplete all as specified & directed.

M&L for coloured glazed ceramic highlighter tile of size 600mm x 300mm x 7 to 8mm thick, colour and pattern as approved by GE, as in vertical surface set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick rendering in cement mortar 1:3 etc including dismantling existing tiling, cement mortar rendering (but not backing), removing rubbish off the premises complete all as specified & as directed.

M&L granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like over and including 15 mm thick screed bed of CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade including dismantling of existing stone slabs/ tiles of any description or thickness laid bedded and pointed in cement mortar and removing rubbish off the premises complete all as specified and as directed.

M&L for Machine cut cudappah stone slab 20 to 25mm thick over and including screed base in CM (1:6) , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling of existing stone slabs/ tiles of any description or thickness laid bedded and pointed in cement mortar and removing rubbish off the premises complete all as specified and as directed.

Labour only for full round moulding to 18 to 20mm thick granite slab all as directed by Engineer-in-Charge.

M&L 75 mm thick plain cement concrete (1:3:6) type C-1 using 20mm graded stone aggregates as in plinth protection, concrete shall be laid in alternate bays not exc 3.0m in length, finished even and fair including demolition of existing cement concrete removing rubbish off the premises complete all as specified and as directed.

M&L Brick work with fly ash old size bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:6 including demolition of brickwork built in cement mortar and rubbish off the premises complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement with sagol finish complete all as specified and as directed.

M&L for 15mm thick cement plaster in CM 1:4 on brick or concrete surfaces finished even and smooth without using extra cement with sponge finish using water proofing compound as per manufactuer's instructions etc complete all as specified and as directed. (Note: Waterproofing compound shall be measured and paid separately under relevant item as supply only).

Supply only liquid water proofing compound make pidicrete of pidilite /cement mix plus of berger all as spd and directed.

M&L for preparation of new plastered or unplastered surfaces and applying two coats of cement base paint over a coat of cement primer all as specified and directed.

M&L for preparation of new plastered or unplastered wall surfaces of any description over 10cm girth or width not otherwise described and applying two coats of acylic distemper over a coat of primer all as specified and directed.

Material and labour for two coats of waterproofing slurry to plastered surface of concrete or brick of wall and Chajjas using Advance latex plus ( make berger or equivalent make of pidilite) with one part ALP mixed with 4 parts water and 7 parts of cement including preparation of surfaces complete all as per manufacturer's instructions and as directed.

Material and labour for two coats of Latex shield 2K make Berger or equivalent grade of pidilite in sunken portion , terrace complete all as per manufacturer's instructions and as directed.

Taking down and removing old water proofing treatment of any description of roof slab and cleaning the surfaces with wire brushes, removing dust, foreign materials and removing the rubbish, debris off the premises to distance exc. 100m and not exc 250m complete all as directed.

M&L for two coats Home Shield PU roof coat of Berger make or equivalent chemical of Pidilite over plastered surface/ concrete surface of roof /wall including preparation of surface complete all as per manufacturer's instructions and as directed.

Material and labour for removing of plants, bushes, weeds with roots from walls, roof, chajja, canopy, parapets, roof kerbs, around water tanks, stagings, outlets junctions of water pipe lines , waste water pipe, bends and filling the disturbed area with cement concrete (1:1.5:3) or cement mortar (1:3) using water proofing compound as per manufacturer's instruction and making the patch finished as per surroundings complete all as specified and as directed. (Note: Rate quoted is deemed to be included for scaffolding, safety measured required for working on or up to height of 15 metres vertical slopes)

M&L for complete removal of existing treatment on walls using steel wire brush, sanding machine, rubbing ivory papers etc and washing , rubbing down and stopping of distempered and painted surfaces, preparing surfaces plastered or unplastered surfaces ready to receive new finish complete all as specified and directed. (For item No. 46, 48 and 50 as applicable)

M&L for complete removal of existing treatment on ceilings using steel wire brush, sanding machine, rubbing ivory papers etc and washing , rubbing down and stopping of distempered and painted surfaces, preparing surfaces plastered or unplastered surfaces ready to receive new finish complete all as specified and directed. (For item No. 47, 49 and 51 as applicable)

M&L for applying wall care putty 1 to 1.5 mm thick on walls surfaces etc complete all as specified

M&L for applying wall care putty 1 to 1.5 mm thick on celing surfaces etc complete all as specified

M&L for applying one coat of alkali resistant priming paint on wall etc complete all as specified

M&L for applying one coat of alkali resistant priming paint on celing etc complete all as specified

M&L for two coats of acrylic distemper of approved tint on wall surfaces etc complete all as specified

M&L for one coat of acrylic distemper of approved tint on ceiling surfaces etc complete all as specified

M&L for one subsequent coat of acrylic distemper of approved tint on ceiling surfaces etc complete all as specified

M&L for applying two coats of 100% acrylic exterior emulsion Apex paint over one coat of primer to mangalore tiles, roof, parapet, wall ,floor etc, on complete all as specified and as directed by Engineer-in-charge.

Preparation of old treated plastered surface of wall by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

M&L for one subsequent coat of acrcylic distemper complete all as specified and as directed.

Preparation of old treated plastered/ false ceiling surface of ceiling by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

M&L for preparation of old decorated surfaces of any description over 10cm girth or width not otherwise described and applying two coats of white wash on walls

M&L for preparation of old decorated surfaces of any description over 10cm girth or width not otherwise described and applying one coats of white wash on ceiling

M&L for preparation of old surfaces of wood and wooden based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint.

M&L for preparation of old painted steel surfaces of any description over 10cm girth or width and applying one coat of synthetic enamel paint.

M&L for preparation of old painted wooden/asbestos surface in ceiling and applying one coat of synthetic enamel paint

M&L for preparation of old treated plastered / unplastered surfaces by brooming down with steel brush and applying one coat of cement base paint complete all as specified and as directed.

M&L for preparation of old treated plastered / unplastered wall surfaces by brooming down with steel brush including removal of moss, fungus, green growth of vegetation,make surface free from loose particles, oil stains etc etc and applying two coat of cement base paint complete all as specified and as directed.

Material and labour for preparation of old treated plastered or unplastered/ concrete surfaces by brooming down with steel brush over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of old treated plastered surface of wall by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying plastic emulsion paint complete all as specified and as directed.

Preparation of old treated plastered surface of wall by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of lustre paint of ASIAN paint or equivalent of Berger/ Nerolac complete all as specified and as directed.

Preparation of old treated plastered surface of wall by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying two coats of lustre paint of ASIAN paint or equivalent of Berger/ Nerolaccomplete all as specified and as directed.

Material and labour for preparation of old wooden surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler and applying one or more coats of french polish till the desired finish is obtained complete all as specified and as directed.

Material and labour for scrapping out old treated wooden surfaces in floors, staircase etc ,sanding the surfaces using sanding machine, application of pigment and hardener to desired colour and finally applying two coats of melamine polish with spray guns, compressor etc complete till glossy surface is obtained complete all as specified and as directed.

- Ditto-all as per item No 68 here-in-before but as in wooden doors, window and wall paneling.

M&L for preparation of old surfaces and applying one coat of 100% acrylic exterior emulsion paint to mangalore tiles, roof, parapet wall ,floor etc, on buildings complete all as specified and as directed by Engineer-in-charge.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete including dismantling unserviceable asbestos cement (Corrugated, Semi corrugated etc.) sheets all as specified and as directed.

S&F in repair for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof, fixed with L-type or J-type or cranked hook bolts etc. complete all as specified and as directed.

S&F in repair for 6mm thick asbestos cement, two piece adjustable serrated ridge for corrugated or semi corrugated sheets fixed with L-type or J-type or cranked hook bolts etc. complete all as specified and as directed.

Dismantling structural steel work including doors, gates, framed truss etc. complete all as directed.

Supply and fix for mild steel work in tubular / rectangular/square trusses, purlins etc including special shaped washer etc. complete using hollow mild steel sections round, square or rectangular for structural use as in main and cross beams, hip and jack rafters, purlins conforming to IS 4923:1997 fixed with angle cleats or other connecting plates complete all as specified and as directed.

Dismantling unframed work timber scantlings 40 sq. cm and over in section, in any position all as directed

Removing debrises obtained from demolition from various locations (other than this work) to a distance of exceeding 3Km but not exc. 5Km outside MOD land complete all as as directed. The location at out side MOD land for disposal of debris material shall be located by the contractor himself).

S&F 35mm thick factory made 2nd class hard wood glazed and skelton shutters divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, open rebated and prepared to receive glass, gauze, edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for screwing glass etc size of member as specified in SSR Pt-I, Section 8, Clause 8.24(b)

Taking down and refixing of old steel rolling shutters/side hung shutters of various size in same opening after carrying out repair replacement of parts necessary by welding or bolting incl greasing,oiling for smooth running of shutters complete all as spd and directed.(MS parts,and other MS flat /angle if required will be measured and paid in relevant S&F item seperately) complete all as specified and directed.

Supply and fix for aluminium anodised powder coated three track sliding window with two glazed shutters with and including 4mm thick tinted glass of modiguard and one gauged shutter with and including stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing, handle, locks, PVC rubber lining of transparent colour etc complete all as specified and as directed. Catalouge numbers of Jindal company or equivalent make sections : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604 complete all as specified and directed.

S&F for aluminium powder coated louvered ventilator with provision of exhaust fan opening using ‘'Jindal” aluminium section including 3 mm thick glass and stainless steel wire mesh 0.36 mm nominal dia of wire, average width of aperture 1.40 mm etc complete all as specified and directed.

S&F aluminum powder coated partition using ‘Jindal’ aluminum SP/DP section with 5mm thick tinted glass with PVC rubber bidding/12mm thick prelaminated particle board fixed with glazing clips etc/ both complete all as directed by Engr-in-Charge.SP (Single partition) - 20033, DP (Double partition) - 20034,Glazing clips - 4407 including taking down existing old wooden partition of any type, description complete all as specified and directed.

Supply and fix for MS frame made out of 25 X 25mm square tube14 gauge thick, 25mm x 38mm aluminium rectangular tube, fixed over mild steel frame to shape semi circular /rectangular over and including 5mm thick coloured aluminium composite pannel (sheet) fixed with screws, cover joints filled with silicon and tape as in semi circular/rectangular sunshade of windows, doors, gate etc. or in wall cladding complete all as specified and as directed. (Aluminium frame/MS frame shall be paid seperately).

Supply and fix in repairs for 12mm thick toughened glass with etching fixed with necessary Ozone path touch fittings as in openable door including chamfered edge polishing etc complete all as specified and as directed.

S&F in repair 3mm thick, plain sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each panes including hacking out old broken glass (any thickness size quality in description from metal frame including punching or drilling old glazing/springs clips and rubbish off the premises all as specified..

Supply and fix in repairs 300mm long antique brass sliding door bolts with sand or die cast brass hasp, staple (bolt type) and fixing bolt with roller or drawn brass bolts, ISI marked, complete all as specified and as directed.( make- Godrej/Quba)

Supply and fix in repairs150mm size antique brass handles, extruded, fabricated type, polished complete all as specified and as directed.( make- Godrej/Quba)

Supply and fix in repairs 200mm long, antique brass barrel tower bolt, with cast or sheet barrel and rolled or cast bolt all complete as specified and as directed. ( make- Godrej/Quba)

S&F floor door stopper of brass alloy body & tongue, with hard drawn steel spring, fixed in floor overall length of cover plate 150mm.( make- Godrej/Quba)

S&F brass cyllindrical lock,for door Grade-I, 4 levers with duplicate keys including brass key hole complete( make- Godrej/Quba)

S&F pull it pully system of 6 feet long make Easy dry system private ltd or euivalent make all as spd and directed

Supply and fix for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

Supply and fix aluminium anodised, barrel tower bolts of extruded section of size 150mm.

Supply and fix aluminium anodised, framing of square hollow pipe for ACP panel.

Supply and fix aluminium handles, cast type, anodised of size 150mm long.

Supply and fix floor door stopper of aluminium alloy body & tongue, double rods, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 140mm.

Supply and fix100mm long butt hinges, medium weight cold rolled mild steel (ISI Marked) all as specified.

S&F in repairs, vitreous chinaware EWC including connection to drain or outgoing pipe and to PVC flushing pipe, antisyphonage pipe all necessary fittings & including plastic water closet seat black closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts complete all as specified and directed.

Supply and fix in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, 32mm dia PVC flush pipe and connections to pipes, making good the disturbed surfaces complete all as specified and as directed.

S&F in repair Vitreous China wash basin, white, flat back, size 630x450mm with brackets including cutting for and pinning in ends of brackets or erecting stand and fixing of supply and waste pipe all as directed and specified.

S&F in repairs, vitreous chinaware orissa pattern water closet squatt pattern of size 580 mm with P or S trap including connection to drain or outgoing pipe and to PVC flushing pipe, antisyphonage pipe all necessary fittings complete all as specified and directed.

Material and labour for 18mm thick plywood, grade BWR, type BB, number of ply 9 Nos, fixed with fevicol and nails for working table/ storage almirah to the size and pattern, includung dismentling existing complete all as shown on drawing and as directed.

Material and labour for 12mm thick plywood, grade BWR, type BB, number of ply 7 Nos, fixed with fevicol and nails for working table/ storage almirah to the size and pattern, includung dismentling existing complete all as shown on drawing and as directed.

Material and labour for 6mm thick plywood, grade BWR, type BB, number of ply 5 Nos, fixed with fevicol and nails for working table/ storage almirah to the size and pattern, includung dismentling existing complete all as shown on drawing and as directed.

Material and labour for 0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer’s instruction complete all as specified and as directed.

Material and labour for 2nd class hard wood cover fillets, bull nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails, sectional area exc. 3 Sq.cm but not exc. 6 Sq.cm complete all as specified and as directed.

Material and labour for 2nd class hard wood cover fillets, bull nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails, sectional area exc. 6 Sq.cm but not exc. 13 Sq.cm complete all as specified and as directed.

Material and labour for 2nd class hard wood cover fillets, bull nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails, sectional area exc. 13 Sq.cm but not exc. 25 Sq.cm complete all as specified and as directed.

S&F stainless steel power hinges suitable for shutter of not exc 0.50 sqm area all as spd

S&F stainless steel hinges 50 mm long for cupboard shutter all as spd

S&F 75 mm long stainless steel handles for cupboard shutter complete all as spd

S&F Safety lever locks mild steel with 4 levers for rolling shuttersall as specifed and directed by Engr-in-Charge

S&F Ball bearing for rolling shutters all as specifed and directed by Engr-in-Charge

S&F in repair mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate all as specifed and directed by Engr-in-Charge

Taking down cement plaster on brick/ stone walling including raking out joints, hacking for key, scrubbing down with water etc and rubbish off the premises complete all as directed.

Supply and fix in repair for 15 mm bore bib taps chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as per Cat No. 7306 of make Prayag or equivalent complete all as specified and as directed.

Supply and fix in repairs 15 mm bore pillar tap, chromium plated, fancy type high pressure screwed for iron pipe all as per Cat No. 9802 of make Prayag or equivalent complete all as specified and as drected.

Supply and fix in repairs for 15mm dia stop cock (male or female thread), chromium plated pressure screwed for iron pipe all as per Cat No. 7318/20 of make Prayag or equivalent complete all as specified and as directed.

Supply and fix in repairs for 15mm dia angle cock, chromium plated, high pressure screwed for iron pipe all as per Cat No. 8510 of make Prayag or equivalent complete all as specified and as directed.

Supply and fix for 15mm dia PVC connection 450mm long including PTMT check nuts etc complete all as specified and as directed

Material and labour for cast iron Nahani trap, with grating of diameter of outlet 75mm including jointing to waste pipe fixed in PCC (1:2:4) type B-1 (using 20mm graded broken stone aggregates) complete all as specified and as directed.

S&F in repairs chromium plated wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete with wall flange with 115mm long bend pipe, connecting legs ,Cat No. 7280 of make Prayag or other equivalent series as approved by GE complete all as specified and as directed.

S&F in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste coupling, waste pipes etc complete all as specified and as directed

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including waste coupling, waste pipes etc complete all as specified and as directed

Supply and fix for aluminium powder coated three track sliding window with two glazed shutters with 4mm thick float glass ordinary quantity and one shutter of stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing handle, locks, PVC rubber lining etc complete all as specified and as directed. Catlouge numbers of Jindal company or equivalent make complete all as specified and directed. Sections of Jindal company : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

Supply and fix in repair for brackets for drapery/ curtain rod, decorative type, powder coated aluminium section as per sample kept in GE (N) Pune office complete all as specified and as directed.

Supply and fix in repair for drapery/ curtain rod of 25mm dia, decorative type, powder coated aluminium section complete all as specified and as directed.

Material and labour for 12mm thick mineral fibre false ceiling board on and including GI powder coated grid work of size 605mm x 605mm with using 32.0 mm x 23.5mm x 1.5 mm thick main tee, 26.5 mm x 23.5 mm x 1.28 mm cross tee and 23.5mm x 23.5mm x 1.5 mm angle fixed to wall for false ceiling including necessary supporting hanger with 3.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling, suspended @ 120 cm C/C both ways, including dismentling old false ceiling boards and grid complete all as specified and as directed. Make :- Armstrong, Diaken, New Age. Note: Height of ceiling is above 5 metres.

M&L for precast cement concrete glossy interlocking paver block, any shape and size as approved , 80mm thick, conforming to IS 15658-2006, M-40 grade in floor/pavement laid dry to the profile, including dismentling existing tiles complete all as specified and as directed. NOTE: Manufacturers test certificate for crushing strength and Water absorption shall be submitted alongwith sample.

M & L for Sand filling under floors for cushioning for paver block including watering and consolidation complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing with all fittings and connections complete all as directed.

Taking up or down 20 mm bore steel tubing with all fittings and connections complete all as directed.

Supply and fix for 15 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fix for 20 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

S&F in repair Grating doom 100mm dia of PTMT (Minimum weight 25gms)

S&F in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

S&F in repair 15 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F in repair Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, for ornamental and intricate design.

Note : 1. Rerformance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

L.T Associate

M/s Akshay Contruction

VISALAKSHI WATER PROOFINGCOMPANY PRIVATE LTD

M/s Asrani and sons