MISC B/R REPAIRS AND PERIODICAL SERVICES BY USING SMART PERIODICAL METHODILOGY TO INTERNAL AND EXTERNAL SURFACES OF OMQs AND SMQs AT SECTOR 31 UNDER GE (AF) MC CHANDIGARH

Amount

M&L Rendering 15mm thick in cement mortar (1:4) on fair face of brick work, or concrete surfaces finished fair and even with out using extra cement with WPC @ 1% by weight of cement, up to Ten meters height including scafolding complete, including taking down cement plaster and racking out joints, hacking for key scrubbing down with water etc, complete all specified and directed by Engr-in-Charge. Note :- WPC shall be measured and paid separetely.

M&L for Rough cast plaster After applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered complete all as specified and directed, including taking down cement plaster and racking out joints, hacking for key scrubbing down with water etc, complete all specified and directed by Engr-in-Charge.

Supply only integral WPC (as per manufacture instructions) complete all as specified.

M&L for Preparation of new plastered / unplastered Wall surface and applying two coats of cement base paint over priming coat, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plaster / untreated surface of wall / coloum, beam, chajja etc. and leveling / edgesing the disturbed surface a thin layer of putty and making smooth by using sand paper applying two coat of extrior acylic emulsion (weather proof treatment) including one coat of ext primer, to be applied using an airless spray machine, complete all as manufacturer's instruction and as directed.

M&L for Preparation of old plastered / unplastered Wall surface and applying one coat of cement base paint, complete all as specified and directed by Engr-in-Charge.

M&L Rendering 15mm thick on brick surfaces of wall in cement mortar (1:6), finished even and smooth without using extra cement, including taking down cement plaster and racking out joints, hacking for key scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge.

M&L for applying 2 mm thick wall care putty on wall new or old surfaces complete all as specified and directed by Engr-in-Charge.

M&L preparation of old/new plaster surfaces and applying two coat of oil bound distemper white or tinted complete,to be applied using an airless spray machine, all as specified and directed by Engr-in-Charge.

M&L for prepration of old surface of wall and applying one coat of oil bound distemper white or tinted, to be applied using an airless spray machine, complete all as specified and directed by Engr-in-Charge.

M&L Rendering 10mm thick on brick surfaces of ceiling, in cement mortar (1:3), finished even and smooth without using extra cement, including taking down cement plaster and racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed by Engr-in-Charge.

S&F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste.

M&L prepration of new surface of ceiling and applying two coat of oil bound distemper white or tinted complete all as specifeid and directed by Engr-in-Charge.

M&L prepration of old surface of ceiling and applying one coat of oil bound distemper white or tinted complete all as specifeid and directed by Engr-in-Charge.

M&L preparation of old wall surfacesand applying one coat of white washing complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old/new surface of wall and applying two coat of white wash in stairecase , garaze complete all as specified and directed by Engr-in- Charge.

M&L preparation of old ceiling surfaces and applying one coat of white washing complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of old wood or wood based surfaces over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of New steel or iron surfaces over 10cm width or girth not otherwise described and applying Two coat of synthetic enamel paint over and including a coat of red oxide primer complete all as specifeid and directed by Engr-in-Charge.

M&L Preparation of old steel or iron surfaces over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specifeid and directed by Engr-in-Charge

Hacking out old broken glass (any thickness) from wooden/steel frames, glazed with putty of fixed with screws complete all as specified & directed by Engr-in-charge.

S&F Glass Sheet plain glass 4 mm thick, glazing with oil putty / 10 mm hollow square section welded or fixed with screwes in square not exceeding 0.5 Sqm in each pane at height up to three story bldgincl necessary scaffolding complete all as specified and directed by Engr-in-charge.

S&F Pinhead glass 4 mm thick, glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatment by scrapping and sanding with mechanical wall sander (having mechanical vacuum mechanisum) having RPM not less than 1500, sanding pad of of diameter of 7'/9' using a 80 grit sand paper to make the surface free from dust, loosew paint etc. by skilled labour complete all as specified.

M&L for one coat of acrylic water based exterior grade primer @ 1L/11 sq. mtr diluted with water in 1:1 ratio to be applied using an airless spray machine of with a flow rate of 2L per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface for painting of subsequent coats.

M&L for two coat water based premium acrylic smooth exterior emulsion of approved colour with silicon additives, with heat reflectant property which can reduce the painted surface temp, by 5 degree and gives excellent protection against UV attack with VOC less than 50 gram/litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1L/6sq mtr diluted with water as per manufacturer instructions applied over priming coat with airless spray machine of paint application with a flow rate of 2L per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint, at any height, complete all as directed.

Cutting of small trees / peepal trees girth not exceeding 15 cm including cutting of trunk portion protuding over wall surface/roof surface/terrace of building of height up to 10.0 mtr. Including necessary scaffolding and necessary safety measure if required and make good the surface in cement mortar (1:3) and applying one coat of anti growth of vegitation chemical as directed by Engr-in-Charge and removing of unserviceable material outside MD land and cleaning site, complete all as specified and directed by Engr-in-Charge.

Writing letters or figure (Blocks, Roman, Italic or Indian of size 15 cms height, 15mm wide tape, 4-5 letters per Tile base, using Reflective sheets/ tapes of Black colour, Plain white coloured tiles of size 300 x 300 mm over vertical surface, over 10 mm thick rendering in CM 1:3, also roughening of existing surface & making good the disturbed portion, complete all as specified.

Writing letters or figure (Blocks, Roman, Italic or Indian of size 15 cms height, 10 mm wide tape, 2 to 3 letters per Tile base, using Reflective sheets/ tapes of Black colour, complete all as specified.

M/S SATYA SAI CONSTRUCTION (BID ID -3334839)

S S CONSTRUCTION (BID ID -3334529)

jmv engineers (BID ID -3335334)