Rehabilitation and Improvement work of Gandhisagar Dam Project (Part-A) under Drip -II.

Amount

22 cm thick dry-stone pitching deprived of quarry spall with individual stone of 22 cm depth and minimum size 0.014 cum complete.

Providing and constructing Dry rubble wall (toe wall) with stone of minimum size 0.021 cum at the base of stone pitching or rip-rap excluding excavation etc. complete.

Providing and laying M-15 grade Mass Concrete design mix using graded aggregates, clean, hard, including cost of all materials, machinery, labour, formwork, cantering, scaffolding, cleaning, batching, mixing, placing in position, levelling, vibrating, finishing, curing, packing joints of shuttering etc. Complete. Using aggregate of maximum size.

Excavation in all kind of soft/loose/hard/dense soils, moorum & moorum mixed with boulders and mud including dressing, placing the excavated soil neatly in specified dump area or disposing off the same as directed, including cost of site clearance, all materials, machinery, labour and dressing etc. Complete.

Providing shotcrete on old damage concrete/masonry surface or on rock surfaces, comprising of cement, sand, coarse aggregates, water and quick setting compound in designed proportions having minimum density of 2000 kg/cum and strength not less than 25 MPA including preparation of surface by removal of old damaged concrete, cleaning by wire brush/ air water jet, including cost of all material, machinery, labour, T&P, cost of other incidental charges and testing as per relevant specifications etc complete. For average 40mm thick layer.

Construction of RCC railing of precast rails and cast in situ vertical post of M30 grade, aggregate size not exceeding 12 mm, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500, center to center spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertical post for expansion, complete as per approved drawings and technical and as per relevant clauses of sections 1500, 1600, 1700 and clause 2703 of specifications (as per MoST specification drawing SD/202 or SD/305)

Filler joint - Providing & fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing & Technical Specification.

Providing cement flush mortar pointing to coursed rubble (size stone) face stone masonry in CM 1: 2 proportion by volume including cost of all materials, labour, scaffolding, raking and cleaning, joints for 50 mm depth, batching and mixing mortar pressing cement mortar into joints finishing, curing etc. complete.

Excavation in soft/disintegrated/weathered rock including wet excavation, dressing, placing the excavated material neatly in specified dump area or disposing off the same as directed, including cost of site clearance, all materials, machinery, labour and dressing etc. Complete. Right side hillock from loading point to kaleshwar turn top drain

Providing and laying M- 25 grade Plain Cement Concrete Design Mix for filling foundation & Sub Structure using graded aggregates clean, hard including cost of all materials, machinery, labour, formwork, cleaning, batching, mixing, placing in position in alternate panels as directed, levelling, compacting, finishing, curing, packing joints of Shuttering etc. complete. Using graded aggregate of maximum size 40mm

Providing and constructing un-coursed rubble stone masonry with approved stones in CM 1: 4 proportion by volume for super structure portions of return walls / abutments including cost of all materials, machinery, labour, formwork, scaffolding, ramp, cleaning, batching, mixing, mortar, packing mortar and wedging, stone chips into joints, finishing, curing etc. complete

Providing 20 mm thick cement mortar plastering in CM 1: 3 proportion by volume in two layers including cost of all materials, labour, scaffolding, raking and cleaning, joints / surface, batching and mixing mortar, smooth finishing, curing etc. complete

Cleaning of one Big well near power grid and barrels (3Nos) inclined from hillock side to Power house and chambal river

Reaming and cleaning by redrilling the vertical pore pressure formed drains on existing drainage holes in instrument gallary including removing of leached matrrial if any inside of holes complete with water jet, air compressore etc. Fixing drainage caps after cleaning of holes etc. complete with all material labour cost & risk of contractor

Mobilization and demobilization of equipment & personal at site for drilling of boreholes

Providing and fixing of CCTV Camera for gandhisagar dam area safety purpose (all items including three-year maintenance) CAMERA DETAILS (including 3 year maintenance)

NVR 32 PORT CP PLUS PROJECT MODEL

PTZ CAMERA 4MP 100 METER

I P CAMERA 4MP METAL BODY 1049

ARMAT CABLE 305M. D—LINK

4 TB HARD DISC (SEAGATE)

RAKE 4U D-LIONK

INSTALLATION CHARGES CAMERA

500 METER PIPE (1200VALUE)

32 INCH TV SMART

19 INCH LCD.

2 TB HARD DISC

DVR 4 PORT

SMPS 40VOT.

CABLE BOX

Drilling by diamond drilling, holes of minimum 75 mm dia. vertical or at specified inclination using diamond core drilling bit, double barrel tube in masonry, concrete or rock including cost of all materials, machinery, labour, water, re-drilling in case of collapse of sides etc., complete.For depth up to 30 m from surface.0° to 10° vertically downwards

Drilling by diamond drilling, holes of minimum 75 mm dia. vertical or at specified inclination using diamond core drilling bit, double barrel tube in masonry, concrete or rock including cost of all materials, machinery, labour, water, collection of core samples, logging & labelling samples, supplying wooden core box and re-drilling in case of collapse of sides etc., complete.Up to but not including 45° to the horizontal (downward)

Conducting percolation test in the drill holes at the desired pressure including water supply arrangements and necessary accessories etc., complete. Add extra beyond 10 m depth for every addition of 10 m depth or part thereof.

Grouting with Micro fine cement grout mix of suitable consistency under specified grout pressure as directed in drilled holes by stage grouting method including cost of all materials, machinery, labour, redrilling, if necessary, etc., complete.

Thick shrub jungle (area above 50% covered by shrubs) clearance involving removal of grass, shrubs, bushes and twigs including rooting out & disposal etc. complete.

Providing and fixing 25 mm dia. steel rock bolts with one end provided with mechanical/ wedge type anchorage and other end provided with threads for fixing washers and nuts including cost of all materials, machinery, labour, ventilation, lighting, drainage, drilling 35-40 mm dia. holes, providing 150 mm long, 20 mm thick steel tapered wedge, providing 10 mm thick and 200 x 200 mm size plate washer and nuts, driving bolt, fixing washers and nuts, tightening bolt by torque wrench after hardness of the cement grout and all other ancillary operations etc., complete.

Providing and applying of wire mesh 100x100x3.15 mm thick including all machinery, labours, cutting, placing. fixing, scaffolding, lighting, drainage, ventilation with providing and all other ancillary operation etc., complete with all lift.

Supply and Erecting of Perforated type Fiber Glass Reinforced Polymer (FRP) /Glass Fiber Reinforced Polymer (GRP) cable tray of specific dimensions. The cable tray shall be hung from ceiling/fixed to wall with necessary angle/ flatiron ceiling suspensors, clamps, nuts, bolts, washers complete with required tees, bends etc. as per specification to complete the job. The tray shall be as follows with transportation.

Supply and Fixing of Fiber Glass Reinforced Polymer (FRP) / Glass Fiber Reinforced Polymer (GRP) flat cover of minimum thickness 3mm as per required size of cable tray

Dismantling the existing armored/unarmored cable or 2/3/4 wires of submain, main, in any system of wiring including recoiling

Dismantling of D.F. board, D.P. switch, T.P. & T.P.N. switch or D.B. of any size complete with board or angle/flat iron frame and making site clear including the refilling hole & repainting to match colour of wall including transportation

Boom Barrier 5m. Model No. CMP 100A Parking

Labour Charge for Removing Old Barrier

Polypropylene Block 685, 4''x4''x18'' weight per block Approx 7 KG, 250 RS per KG,(250x7=1750)

Lifting and Stacking of Cable for above work

Rail pole Supply of support for overhead line rail pole of I.S. standard including base plate, welding, drilling of required hole etc. complete as required. Steel tubular pole Supply of steel tubular pole swaged type as per IS:2713-1980 complete with base plate and top Canopy, SP-2 - 7.00 metre ,410 SP-2 - 7.00 metre with transportation.

Erection of poles, length 7 metres but not exceeding 10 metres Erection of RS Joist pole/'H' beam/steel tubular/steel rail pole of length 7 metres but not exceeding 10 metres in cement concrete 1:3:6 (1 cement: 3 core sand: 6 graded stone aggregate 40mm nominal size) base, foundation, muffing including excavation and back refilling etc. as required.

Single core PVC insulated FRLS cable Supplying and drawing single core PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing rigid PVC casing and capping/conduit in surface or concealed as per specification.35.00 sq. mm. cable,1 wire 1 X 35.00 sq. mm.

Aerial bunch cable accessories suspension clamp, Supplying & fixing of aerial bunch cable accessories suspension clamp i/c required attachment for single core cable of approved make on pole with clamp, necessary material as per specification for required size.

Aerial bunch cable, accessories tension clamp (dead end), Supplying &fixing of aerial bunch cable accessories tension clamp (dead end) i/c required attachment for single core cable of approved make in air with clamp, necessary material as per specification for required size.

Angle/channel/flat iron fitting for overhead line & substation etc. Supply, fabrication and erection of angle/channel/flat iron fitting for overhead line & sub- station etc such as 'D' bracket, cross arms, top clamp, 'V' cross arms, back/support clamp or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of aluminum paint as required as per specification. 3-phase line

Piercing connector, Supplying & fixing of waterproof insulation piercing connector for aerial bunch cable i/c required attachment for single core cable of approved make in air with necessary material as per specification of required size as mentioned below

Supply of ISI marked On-Load change over switches panel mounting type conforming to IS: 13947 (part I & III) with front operated 4 pole, 415 V with two earthing terminals if required. ,63A (With enclosure)

Street light with high power LED system Supply and fixing street light with high power LED of 3 to 6 Watt each on existing bracket assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy>120 lm/Watt. luminiare having color temp upto 6500K & 50000 hrs. burning life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare comprises of driver, PF> 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass, IP65 protection. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347 i/c connection wire, testing etc. to complete the job. 60Watt, color temp 3000-6500k as required.

Supplying and laying of approved make stainless steel wire rope 6 mm thick complete with binding for support of pump and motor.

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS: 8828: 1996, IEC: 60898 :2002 & 60947-2 but without enclosures: - Four pole, MCB FP 6Amp to 32Amp 10kA rating

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS: 8828: 1996, IEC: 60898 :2002 & 60947-2 but without enclosures: -, double pole, MCB DP 50Amp to 63Amp 10kA rating

Contactor 2 Pole rating 240/415V, Supplying and fixing of contractor 2 Pole rating 240/415V: for ON - OFF street light of approved make in existing LT panel including connections etc. as required as per specification

Supply of two-way Centre off MCB changeover switch conforming to IS:13947 (part III)/IEC: 60947- 3, 2/4 pole, AC 240/415 Volt, 50 Hz ,40Amp, Double pole (DP)

MCB 'C' Series, 240/415V, 50 Cycle,10kA/15kA, Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :-, MCB SP For 40Amp 10kA rating

Analog time switch for automatic ON - OFF street light, Supplying and fixing of analog time switch for automatic ON - OFF street light of approved make in existing LT panel including connections etc. as required as per specification

Dismantling of poles, dismantling of existing steel pole, R.S. Joist, girder with bracket clamp insulator or stay from the cement concrete foundation and making the site clear by refilling the pit to ground level i/c transportation to required destination within township.

Dismantling of overhead conductor, dismantling of existing overhead ACSR, AAAC, GI, conductor and making the site clear i/c transportation to required destination within township. Including transportation

Supply and fixing integral post top lantern LED fitting comprises of copper dust finish cast aluminium spigot and spun aluminium canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting, open construction driver and accessories are wired upto terminal block. LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100lm/Watt. LED driver PF > 0.95 & surge protection 10KV. The colour rendering index of LED light should be more than 70. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. 40-Watt LED, color temp 3000-6500k as required.

Providing and erection of black painted galvanized decorative designer poles in different section, top 60mm dia., bottom 140mm dia. with gold colour painted ornamental cast aluminium ring having lockable weather proof flush door junction box in bottom section, base plate dia. 290mm having 4 holes of 22mm dia. complete erected in an approved manner on existing foundation. Suitable size & type of foundation bolts 4 nos. X 16mm X 450mm 'J' type (EN8 grade) 3 meter Height

Supplying & installing G.I. pipe for protection of underground cable fixed on wall/support/in trench/fixed between two rigid existing support of wall/beam for erection of ceiling Fan/down rod for stiff pendent for light luminaries /fan/protective for earthing, lightening conductor down strip/overhead service line/for submersible cable or centrifugal pump for water supply with necessary iron clamp coupler, bend, tee, elbow, nuts and bolts etc. complete in an approved manner as required to complete excluding cost of excavation/dismantling & other finished masonry Item complete For 'B' class pipe ISI marked (IS-1161-68)

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor

Unarmoured 2 core 10 sq. mm.

3½ core unarmoured 25 sq. mm

Supplying and drawing single core PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing rigid PVC casing and capping/conduit in surface or concealed as per specification.

(i) 1 X 2.5 sq. mm.

Supplying of ISI marked iron clad/metal clad triple pole and neutral switch fuse unit with two earthing terminals & without HRC fuses – (i) 100Amp 415/500 Volts.

Erection of metallic street light pole length 3 metres but not exceeding 6 metres in cement concrete M-10 (1cement:3coarse sand:6 graded stone aggregate 40mm nominal size) foundation with cement concrete collar of size 0.4 metres dia x 0.5 metres height to accommodate the looping type cable end box including excavation and refilling etc. as required

Laying of underground cable armoured./unarmoured as per specification in air suspended on existing approved type of iron clamp, G.I wire 7/1.6mm & shackle insulator/insulated strip complete.

1/2/3/4 Core cable upto 16 sq. mm

1/2/3/3½/4 Core cable 25 sq. mm to 120 sq. mm

Providing laying and jointing of following galvanized Iron (MS) Pipes with specials (such as bends, elbows, tees etc) class light, medium & heavy including testing of joints, cost of pipes, specials and jointing materials all complete. Pipes and sockets conforming to IS-1239/2011 PartII

100mm dia Heavy for Pumping Water From Dam Reservoir to Chambal Mata Overhead Water Tank

50mm dia.Heavy for water supply from loading point to downside line upto Kaleshwar temple

15mm Dia Heavy for drinking water supplies at each Gate chamber

Providing and fixing following class-I Globe wheel valves, confirming to IS 778/1984 (Reaffirmed 2005), tested to 21.09 kg/sq.cmt.

100 mm dia ( Flanged )

50 mm dia ( Flanged )

15 mm Dia ( Flanged )

Providing & fixing including testing water taps 15 mm Dia Stainles Steel

Providing and fixing G. I. Bend 90 degree in G.I. Pipe line i/c cutting threading testing etc. complete (Old work) confirming to IS 1879 15mm dia

Providing and fixing G. I. Elbow in G.I. Pipe line i/c cutting threading testing etc. complete (Old work) confirming to IS 1879

Providing and fixing G. I. socket in G.I. Pipe line i/c cutting threading testing etc. complete (Old work) confirming to IS 1879 15 mm dia

Providing and fixing G. I. Tee in G.I. Pipe line i/c cutting threading testing etc. complete (Old work) confirming to IS 1879 15 mm dia

Providing and fixing G. I. Union in G.I. Pipe line i/c cutting threading testing etc. complete (New work) confirming to IS 1879 15 mm dia

New overhead Water Tank (GRP SECTIONAL PANEL TANK) with capacity of 40000 liters, made of Zn Aluminum clad Metals sheet as per industrial water supply standard for supplying of water to Chambal Mata Statue and tank should be placed 25 meter Above from ground level to maintain the flow required for waterfall and to maintain the Head for supply with civil structure for base formation and truss formation with 4 inches L shaped MS angles

60 hp Multi Stage Borewell Submersible Motor Pump with automatic star delta online starter and trolly arrangement ko keep the pump movable at new inclined separate civil structure with railing and chain pully system arrangements or jack well formation for changing Dam water level in different seasons

Supplying and fixing flood light with high power LED of 3 to 6 Watt each assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy>120 lm/Watt. luminiare having color temp upto 6500K & 50000 hrs. burning life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare comprises of driver, PF > 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass, IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job

120Watt, color temp 3000-6500k as required

250Watt, color temp 3000-6500k as required

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottom disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. (No extra lift is payable if work is done by mechanical means) All kinds of soil

Dry Lean Cement Concrete Sub- base Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing as per clause 601of specification complete in all respect.

Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement M-30 grade concrete over a prepared sub base with cement , coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, admixtures as approved, curing compound, finishing to lines and grades as per drawing as per IRC 15 2011and as per relevant clauses of section 602 of specifications complete but excluding cost of steel in dowel bar and tie rods etc.)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : M15-Grade concrete

Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign board as per IRC 67-2010 made of high intensity Micro-Prismatic Grade Sheeting (Type IV) vide clause 801.3.3 fixed over Aluminium composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminium with overall thickness of 4mm and aluminium skin of thickness 0.3 on both side, the ACM shall conform to Table 800-1 of specification and High Intensity Micro Prismatck Grade Sheeting shall conform to Table 800-3 of specification. The printing on the high intensity grade sheeting shall conform to Clause 801.3.7 with water based latex optimized transparent ink as specified by the sheeting manufacturer, supported on composite sign post of size 75mmx33.55mmx34.99 mm (5mm thick) made of Aluminium composite material in accordance to IRC 67-2010 fixed to ground by means of properly designed foundation with M15 grade concrete 450x450x600mm The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts.

60 cm equilateral triangle

60 cm circular

80 mm x 60 mm rectangular

60 cm x 45 cm rectangular

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: in lime mortar

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate (M 10)

Providing cement mortar flush pointing to coursed rubble (size stone) face stone masonry in CM 1 : 3 proportion by volume including cost of all materials, labour, scaffolding, raking and cleaning, joints for 50 mm depth, batching and mixing mortar pressing cement mortar into joints finishing, curing etc. complete.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm or more (having thickness 9 to 10mm) of 1st quality conforming to IS : 15622 of approved make in all colours white, ivory, grey, fume red brown laid on 20mm thick cement mortar 1:4 (1 Cement : 4 sand) including grouting the joints with white cement and matching pigments etc., complete.

8 mm thick.stones Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mmthick bed of cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings. This included jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer-in- Charge.25 mm nominal outer dia .Pipes.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level with : Cement mortar 1:6 (1 cement : 6 sand)

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth course of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45, 1.20 and 1.45 Kg per square metre of area respectively, second and fourth courses of roofing felt type 3 grade I conforming to IS : 1322 (Hessian based self finished bitumen felt) conforming to IS : 1322 and sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic dm per sqm including preparation of surface but excluding grading, complete. (with five years service gurantee).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : second class teak wood

Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of stone dust, compacting and proper embedding/laying of inter locking paver blocks into the bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including locking edges with M 15 cement concrete in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications and direction of Engineerin- Charge. 80mm thick C.C. paver block of M-35 grade with approved colour, design and pattern.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area beyond 3 sq. metres

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant ) etc. as per specifications, drawings and direction of Engineer-in-charge complete. also including of electrical work

Providing and laying Ceramic glazed floor tiles 300x300 mm or more (having thickness 6 to 7mm) of 1st quality conforming to IS : 15622 of approved make in any colours and shade laid on20 mm thick Cement Mortar 1:4 (1 Cement : 4 sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of stone dust, compacting and proper embedding/laying of inter locking paver blocks into the bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including locking edges with M 15 cement concrete in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications and direction of Engineerin- Charge. 80mm thick C.C. paver block of M-35 grade with approved colour, design and pattern.

Supply & fixing fencing of chain link mesh 100 x 100 mm, 12 SWG GI wire for D.P. structure electric substation switchyard including single post of angle iron size 50x50x5mm, 2.5 mt long should be provided upto 2.00 mt. apart or as required. The panel frame with required angle iron/ flat iron members/cross members including mesh welded in frame panel shall be erected between the posts. The angle iron post shall be erected in cement concrete M15 (1:2:4) (20 mm graded metal) foundation, including excavation of the pit and refilling the same. The fencing shall be provided with one entrance gate including locking arrangement as required as per specification. The height of fencing shall be 2 mt. above ground level. Fencing shall be painted with required shade.

Acrylic 3D Sign Board with all material, labour and machinery charges for installations. (After removing existing unwanted materials and repairing structure, making new structure if required, painting the structure, testing and trials included)

PSSC INFRA PRIVATE LIMITED (BID ID -1249878)