Rehabilitation of Anicuts, Construction of canal head sluices, culverts and inlets and improvements to supply channels in Paralaiyar river in Paramakudi, Kamudhi and Muthukulathur Taluk of Ramanathapuram District.

Amount

Clearing Juliflora Jungle without uprooting

Clearing juliflora jungle with uprooting as directed by the Engineer complying with standard specification.

Dismantling, clearing away and carefully stacking material and without disturbing nearby structure useful for reuse for any thickness of brick or stone masonry in Cement Mortar walls under 3 (Three) meters high etc, complete as directed by the Engineer in charge of works and as per the technical specifications.

Dismantling, clearing away and carefully stacking material and without disturbing nearby structure useful for reuse for any thickness of plain cement concrete etc, complete as directed by the Engineer in charge of works and as per the technical specifications

Earth work excavating and depositing on bank with a initial lead of 10 m & initial lift of 2 m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size of boulders hard gravelly soil including refilling the excavated earth as directed by the Engineer in charge and watering and consolidation of earth fill layers throw appropriate compaction equipment complying with standard specification and as directed by the departmental officers. (cut open bund) SS 20B

Earthwork excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size of boulders hard gravelly soil inclusive of shoring to full depth strutting and bailing out water wherever necessary and refilling the sides of foundation with excavated soil other than sand in layers of not more than 15 cm thick, well rammed, consolidated and depositing the surplus earth in places as shown by the departmental officers with an initial lead of 10 metres and initial lift of 2 metres and clearing, levelling the site etc., complete complying with standard specification and as directed by the departmental officers.

Earth work deploying earth moving machineries for desilting channel and forming bund on either side depositing the earth on banks including jungle clearence etc., complete complying with standard specification and as directed by the Departmental Officers.

Having width 3m to 10m

Having width more than 10 m

Collection and supply of Sand Gravel mix 1:1 (one CS sand and one gravel) ratio for basement including stacking, mixing and spreading the Sand Gravel mix in layers of not exceeding in 150 mm thickness over properly prepared surface, watering and consolidating the same with approved type of compaction equipment complete complying with the standard specification and as directed by the Engineer in charge of work.

Providing and placing Plain Cement Concrete M10 grade using crusher broken hard coarse aggregate (well graded) of nominal maximum size of 40mm and downgraded to I.S specified grading (To achieve the specified characteristic strength of 10N/mm2 in 28 days) and mixing the ingredients in approved mixer including dewatering of the placement site by baling / pumping and diverting wherever necessary, placing concrete in layers, water curing, finishing the surface with all leads and lifts compacting and finishing the surface watering, curing wherever necessary for various depth and height below and above ground level so as to attain the profile and strength specified in the drawings etc., complete complying with standard specification and as directed by the Departmental Officers.

Below GL-1.50m Lvl to -4.50 m Lvl

Below GL-1.50m Lvl to AGL +1.00 m Lvl

Providing and placing in position of plain Cement concrete of grade M15 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 40mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers

Below GL-1.50m Lvl to -4.50 m Lvl

Below GL-1.50m Lvl to AGL +1.00 m Lvl

Providing and placing Plain Cement Concrete M15 grade using crusher broken hard coarse aggregate (well graded) of nominal maximum size of 20mm and downgraded to I.S specified grading (To achieve the specified characteristic strength of 15N/mm2 in 28 days) and mixing the ingredients in approved mixer including dewatering of the placement site by baling / pumping and diverting wherever necessary, placing concrete in layers and vibrating, water curing, finishing the surface with all leads and lifts etc., complete complying with standard specification and as directed by the Departmental Officers.

Below GL-1.50m Lvl to -4.50 m Lvl

Below GL-1.50m Lvl to AGL +1.00 m Lvl

Providing and placing in position of plain Cement concrete of grade M15 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 40mm (60%) and 20mm (40%); weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; vibrating, compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers. with vibration(SS20B)

Below GL-1.50m Lvl to -4.50 m Lvl

Below GL-1.50m Lvl to AGL +1.00 m Lvl

Above GL +1.00m Lvl to 4.50m Lvl

Providing and placing in position of plain Cement concrete of grade M20 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 20mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers. without vibration Wearing coat Sluice & Weir) with Vibrator

Providing and placing in position of plain Cement concrete of grade M20 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 20mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers. without vibration Wearing coat Sluice & Weir) without Vibrator

Below GL-1.50m Lvl to AGL +1.00 m Lvl

Above GL +1.00m Lvl to 4.50m Lvl

Providing and laying in position of Standardised Concrete Mix M25 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 350 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 25N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Below GL-1.50m Lvl to AGL +1.00 m Lvl

Above GL +1.00m Lvl to 4.50m Lvl

Providing Steel centring for RCC Slabs, beams or plain surfaces including strutting upto 3.29 m high using MS sheets, 10 guage thick of size 90cm x 60cm, Stiffened with Ms angles of size 25mm x 25mm x 3mm laid over silver oak joists of size 10 cm x 6.5 cm spaced at 90 cm c/c and supported by casurina props of 10 cm to 13cm dia spaced at 75 cm c/c and removing the centring and shuttering after specified period without damaging the concrete laid, etc., complete complying with standard specification and as directed by the Departmental Officers. (For Retaining walls and Sluices)

Without Strutting

With Strutting (0 to 3.29m Lvl)

Supplying, fabricating and placing in position of HSD (high Yield Strength) bars for all reinforced cement concrete works including cost of binding wire, steel rods, conveyance charges and labour charges etc., complete complying with standard specification and as directed by the Departmental Officers. (Specification No.9.1 to 9.12.1) cutting, bending and tying the grills complete complying with standard specification. Steel and binding wire will be at the contractor's own cost.

Providing filter zone below the concrete block with M sand for bottom layer and broken graded stone for top layers as furnished in the drawing and as directed by the departmental Engineer including collection of coarse sand conveying, stacking the same for pre-measurement and providing a layer of 20cm thick, watering and consolidating, supplying hard broken stone of the following sizes, stacking for pre-measurement,. laying the stones of 10 mm size for 7.5cm thick, 20mm size of 7.5cm thick, 40mm size for 10cm thick and 80mm size for 15cm thick in layer etc., complete complying with standard specification and as directed by the departmental officers.

Gravel backing for apron and revetment of 15cm thick including the cost of gravel at site of work, mixing with water so as to form into stiff plastic balls and laying and finishing etc., complete complying with standard specification.

Rough stone dry packing using new stones for apron and revetment including stacking charges for premeasurements and finishing etc,complete complying with standard specification and as directed by the specification and as directed by the departmental officers

Rough stone dry packing for apron and revetment using old available hard granite stone including stacking the stones for Pre-measurements complying with standard specification.

Providing and fixing weep holes of 110mm dia pvc pipes of working pressure 4kg/m2 to a required length for protection wall, abutment and wing wall including cost of conveyance of all materials to work site including cost of labour charges for 90cm spherical back fill arrangements with 110mm dia and 20mm size hard granite broken stone charges at the peripery, the labour charges for fixing and to drain the back fill etc., complete complying with the standard specifications and as directed by the departmental officers.

Refilling the excavated earth in layers not exceeding 23cm thickness and watering to OMC (Optimum Moisture content) and compaction of each layer to 95% of proctor Density through deployment of appropriate compaction equipment (8-10T power roller) vibratory power roller of short width ( 0.90m width drum) power roller or vibratory power roller/fuel operated or electrically operated, vibratory plate compactors, ensuring compaction of designed bund section including side slopes etc., complete complying with standard specification and as directed by the Departmental Officers.

Providing construction contraction and lift joints in masonry concrete with jointing and placing mastic pad of 20mm thick with mastic filling as specified in the drawings directed by the departmental officers complete complying with standard specification. ( for Protection wall masonry and concrete joints).

Providing and laying in position of Standardised Concrete Mix M20 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 325 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Supplying demarcation R.C.C. pre cast post in Cement concrete M20 grade with well graded aggregates and the nominal maximum size of coarse aggregate of size 20 mm of size 0.15 x 0.15 x 1.20 M and fixing the post 40 Cm depth below ground level, the post includes using 4 numbers of 8 mm RTS main rod to a length of 1.325 M, using 6 mm MS 9 numbers as strrups with steel centering and painting the post with enamel paint to a height of 0.80 M alround the post etc. complete and conveying the post to the site of demarcation boundary such as tank bund and foreshore including earth work excavation for foundation in HSC, and the post embedded by using Cement concrete M10 grade with well graded aggregates and the nominal maximum size of coarse aggregate of 20 mm, as per the direction of the Engineers and complying with standard specification.

Pointing with cement mortar 1:4 (One cement and four sand) for flush pointing in Random Rubble masonry complying with standard specification.

Earthwork in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machineries and tippers including benching, formation of bunds, breaking clods, sectioning etc. complete including extra watering and compaction of earth fill layers to specified density of 95% of proctor density through deployment of appropriate compaction equipment (standard 8-10 ton power roller; short width drum vibratory power roller; vibratory power roller, complete complying with standard specification and as directed by the Departmental Officers.

Providing composite paddle shutters with shutters of various size is made of composite material as per the following specification. The skin plate shall be made out of 6mm composite panel. The composite horizontal stiffeners on the rear side shall be made of 35x40x5mm channel. The vertical stiffeners shall be made of 35x40x5 mm angle lifting handle in mild steel rod 20mm dia & length 200mm shall be impregnated at the top of the shutter on either sides. Twi 12mm holes shall be suitably drilled in the handle to accommodate MS bolts & nuts and connect to the shutter. The composite paddle shutter shall be given a corrosion resistance & UV barrier coating. The composite shutter has good mechanical properties, ease in handling and excellent corrosion resistance property. Then the shutter shall be loaded, transported to the site, unloaded & erected as directed by the departmental officers. The cost includes cost of all materials, pattern and mould cost, process charges ,cost of consumables, process charges, labour charges for dismantling, loading, lifting, unloading, transport, erection, hire charges for equipments like grinding machine, conveyance to site and clearing them after completion of work, including cost of trial operation, etc., complete as directed by the departmental officers.

Fabricating, Supplying and erection of Screw gearing steel shutters of size above 1.00 m and upto 2.00m width consist of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50mm mild steel channel at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipments required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc..complete

Fabricating, Supplying and erection of Screw gearing steel shutters of size above 2.00 m and upto 3.00m width consist of skin plate made out of 10mm thick mild steel plate and horizontally stiffened with 150x75mm ISMB 150 at an interval not more than 0.50m and vertical stiffeners made out of 100x50mm mild steel channel ISMC at an interval not more than 0.60m and provided with 10mm thick mild steel gusset plateof required size on both sides fastened with rust free bolts and nuts etc.Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipments Erecting the new shutter and the shuttering arrangements in the vent in proper position by using necessary hoisting equipments. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipments required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc..complete

Fabricating, supplying and fixing of 63mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod,conveying and stacking at section store. The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete

Fabricating, supplying and fixing of 80mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod, conveying and stacking at section store. The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete

Fabricating, supplying and fixing of Shutter Groove Angle made up of 100x100x10mm Mild Steel angle for required height including welding hold fast of size 40x40x6mm Mild steel angle 3 Nos on both sides and conveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment including dismantling the existing damaged groove angles, conveying and stacking at section store. The groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours, charges for all fabricating and hoisting equipments, conveyance, petty civil works and warranty for 5 years etc., complete.

Fabricating, Supplying and fixing of Top Beam made up of 150x75mm (ISMB 150) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 12mm mild steel plate of size 0.30 x 0.15m 2Nos with required holes. Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete.

Fabricating, Supplying and fixing of Top Beam made up of 200x100mm (ISMB 200) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 16mm mild steel plate of size 0.20x 0.30m 2 Nos with required holes. Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete.

Supplying and fixing of Head Set Assembly medium duty with hexagonal nut (Approximate 70 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust fre bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly, conveying and stacking at sectio store. The Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc., complete

Supplying and fixing of Bottom Flat Rubber seal with Mild Steel Flat plate throughout the length of Rubber seal and fitted with the existing structure by means of Mild Steel Washers, Nuts and Bolts including dismantling the old corroded bolts by cutting, removing old flats and hardened or damaged old rubber seals beam, then conveying, loading and unloading and stacking to section store, etc.., complete.

Providing new 3T capacity worm gear box assembly consist of cast iron top and bottom plates, worm nut made up of pig iron, worm shaft made up of EN8 steel rod and two numbers of thrust bearings. The top and bottom plates machined to suit the worm nut and shaft. The worm nut threaded inside to suit the 63mm dia screw rod and the outer side formed with helical teeth cutting to suit the worm shaft. The worm shaft machined to the required shape and size and provided with helical teeth to suit with the worm nut.The assembly fixed with two numbers of thrust bearing one on top and another on bottom of the worm nut and fastened with required bolt and nuts. The operating key made with 80mm square rod shaping with wire cutting machine and welded with operating handle made up of 32mm dia steel rod for required length. The gear box is to be rest on the top of MS stand made up of 75x75x8mm MS angle and the top covered with 16mm thick MS plate and the stand fixed on the 150x75mm MS channel fixed over top of the beams in platform. The gear box align with the screw rod and fixed with required bolts nuts etc., complete and as directed by the departmental officers. Painting the hoisting arrangements with two coat of aluminium oxide paint over two coat of zinc rich primer The rate including cost of worm gear, cost of all materials required, labour charges, process charges like gas cutting, welding, machining, milling, labour charges for dismantling, loading, lifting, unloading, transport, erection, charges for equipment’s like derrick, chain pulley block, conveyance charges of to and fro of equipment’s and labours to the site including cost of trial operation of the Shutter, inclusive of all taxes, etc., complete and as directed by the departmental officers and warranty for 5years etc., complete .

S.G.Shutter size of 1.30 X 1.60 m

Fabricating, Supplying and erection of Screw gearing steel shutters of size above 1.00 m and upto 2.00m width consist of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50mm mild steel channel at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipments required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc..complete

Fabricating, supplying and fixing of 63mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set . The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete

Fabricating, supplying and fixing of Shutter Groove Angle made up of 100x100x10mm Mild Steel angle for required height including welding hold fast of size 40x40x6mm Mild steel angle 3 Nos on both sides and conveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment . The groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours, charges for all fabricating and hoisting equipments, conveyance, petty civil works and warranty for 5 years etc., complete.

Supplying and fixing of Head Set Assembly Heavy duty with hexagonal nut (Approximate 70 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment . The Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of malerials, labours, charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc, complete..

Fabricating, Supplying and fixing of Top Beam made up of 200x100mm (ISMB 200) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 16mm mild steel plate of size 0.20x 0.30m 2 Nos with required holes. Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete.

Painting with two coats of coaitarepoxy paint over two coat good quality zinc rich primer. This includes cleaning the surface to be painted to remove grease, oil, and other impurities and coating the surface with zinc rich primer (85%+/-5% zinc content) as per IS 14177:1994 and then application of two coats of coaitar epoxy paint.

Supplying and fixing of Bottom Flat Rubber seal with Mild Steel Flat plate throughout the length of Rubber seal and fitted with the existing structure by means of Mild Steel Washers, Nuts and Bolts.Then conveying, loading and unloading and stacking to section store, etc.., complete.

S.G.Shutter size of 1.15 X 1.05 m

Fabricating, Supplying and erection of Screw gearing steel shutters of size above 1.00 m and upto 2.00m width consist of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50mm mild steel channel at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipments required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc..complete

Fabricating, supplying and fixing of 63mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set . The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete

Fabricating, supplying and fixing of Shutter Groove Angle made up of 100x100x10mm Mild Steel angle for required height including welding hold fast of size 40x40x6mm Mild steel angle 3 Nos on both sides and conveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment . The groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours, charges for all fabricating and hoisting equipments, conveyance, petty civil works and warranty for 5 years etc., complete.

Supplying and fixing of Head Set Assembly Heavy duty with hexagonal nut (Approximate 70 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment . The Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of malerials, labours, charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc, complete..

Fabricating, Supplying and fixing of Top Beam made up of 150x75mm (ISMB 150) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 12mm mild steel plate of size 0.30 x 0.15m 2Nos with required holes.Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete.

Painting with two coats of coaitarepoxy paint over two coat good quality zinc rich primer. This includes cleaning the surface to be painted to remove grease, oil, and other impurities and coating the surface with zinc rich primer (85%+/-5% zinc content) as per IS 14177:1994 and then application of two coats of coaitar epoxy paint.

Supplying and fixing of Bottom Flat Rubber seal with Mild Steel Flat plate throughout the length of Rubber seal and fitted with the existing structure by means of Mild Steel Washers, Nuts and Bolts.Then conveying, loading and unloading and stacking to section store, etc.., complete.

CHITRAHEM CONSTRUCTION COMPANY (BID ID -1445340)

G ILANGUMARAN (BID ID -1446090)