REPAIRS TO PATHS GATES GRILLS OPEN CLOSE DRAINS COMPOUND WALL FENCING HARDSTANDING AND CERTAIN MISC B/R WORKS AT ZONE C AREA AT NDA KHADAKWASLA

Amount

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc including cleaning off premises where complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints,hacking for key ,scrubbing down with water etc complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including cleaning off premises where complete all as specified and directed.

M&L 75 mm thick PCC (1:4:8) type D2 using 40 mm size graded stone aggregates as in sub base complete all as specified and directed.

M&L for rough dressed sahabad stone slab flooring (30 mm thick) incl bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) complete all as specified and directed

Ditto all as per Item No 5 above here-in-before but except sahabad stone.

M&L for glossy finish machine pressed precast conctete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade incl 30mm thick sand chusioning complete all as specified and directed

M&L for 100 mm thick PCC (1:2:4) Cement concrete type B-1, 1:2:4 (20mm size graded stone aggregate) and Finishing cement concrete surface even and smooth Without using extra cement complete all as specified and directed

M&L for providing & laying 100 mm thick Cement Concrete with nominal mix 1:1.5:3 tremix concrete and tremix machine and plate vibrator by using 20mm graded coarse aggregates as in floor surface/ hardstanding/roads/slabs over drain; finished surface of concrete surface with smooth finish as required without using extra cement etc complete all as specified and directed

M&L for forming Contraction (dummy) joint 60mm deep x 5mm wide filled with sealing compound grade 'A' as in floor surface complete all as specified and directed

M & L for providing precast RCC 1:2:4 type B1 (using 20mm grade stone aggregate as in cover slabs for manholes set in CM (1:6) complete including dismantling of existing all as specified and directed ( Note : Reinforcement shall be measured & paid separately)

S & F for providing mild steel TMT bars 6 to 8 mm dia cut to length bent to shape required includig cranking, bending etc & binding with ms wires (annealed) n. exe 0.9mm dia complete all as specified and directed

M & L Cement concrete type C- 2, 1:3:6 (40mm graded aggregate) 75 mm thick as in plinth protection incl complete all as specified and directed

Dismantling of stone sett pavings any description or thickness laid bedded pointed in cement mortar in floors, appron etc. complete all as specified and directed

M&L for Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified and directed

M&L for light colour non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) in floors etc, area of each tile exc 0.11 sqm and n. exc .18 sqm, set and jointed in neat cement slurry and pointed in coloured cement to match over and incl 20 mm thick screed bed or bedding layer in CM (1:4) complete including dismantling of existing tile work all as specified and directed

M&L for Colored ,Glazed ceramic tiles in vertical wall surfaces 350x250mmx7mm / 450X350X7mm thick set and jointed in neat cement slurry and pointed in white or color cement to match, laid over and incl provn of 10 mm thick plaster in CM (1:3), complete including dismantling of existing tile work all as specified and directed

M&L for joint free Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 including dismantling of existing tile work complete all as specified and directed

M&L Machine cut cuddapa stone slab 20 to 25mm thick over cement screed base ,laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete all as specified and directed

M & L machine cut superior quality Kota stone slab flooring 20-25 mm thick over cement screed , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete match including bulnosed to edges complete and incl 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

Demolition of brick / block masonry / Stone masonry built in Cement mortar complete all as specified and directed

M&L precast cement concrete 1:3:6 type C-1 ( using 20mm graded aggregate ) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar 1:6 complete in wall all as specified.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

M&L for Rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surfaces as in ceiling finished even and smooth without using extra cement complete all as specified and directed

M&L for Rendering 15mm thick in two layers, 5mm thick in CM 1:4 with WPC over a coat of 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement (at any height incl necessary scaffolding) complete all as specified and directed

Supply only integral water proofing compound complete all as specified and directed

Extra for forming fair finished drain or channel girth not exc 30cm in cement concrete using extra cement including form mounds etc complete all as specified and directed

M&L Preparing new plastered surfaces of wall applying two coats of cement base paint complete all as specified and directed

M&L Walling of squared rubble, regular coursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed

M&L for Raised pointing to random or polygonal rubble, uncoursed on brought upto courses in cement mortar 1:4 complete all as specified and directed

M&L Raking out joints/pointing to squared rubble masonry, coursed or uncoursed built in cement mortar complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S&F for framed work as in doors or gates of angles or other section with gussest plate, rails, braces,etc complete drilled for fixing of steel sheeting or other covering door etc, to be prepared for hanging or sliding with and encluding either hooks and hinges or steel hanging door fitting incl of steel sheeting or other covering , running railand guides and hanging, also fastening and fixing complete all as specified and directed

Dismantling posts or structs (wood steel or RCC) any section, including taking out embedded portion and making good distrubed ground complete all as specified and directed

M & L for PCC (1:2:4) type B2 (using 40mm graded stone aggregate) in foundation , filling and mass concrete complete all as specified and directed

S&F rolled mild steel angle iron posts for fencing posts and struts split at bottom including flat iron 40x4 mm with necessary welding with drilling bolting or rivetting etc and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed

S&F mild steel round bars , 10 mm dia and over cut to length , bent to shape as in staining to fencing complete all as specified and directed

Fixing only Chain link MS gavanised fencing any size ot type including line wires, any mesh, size and type of standard, rails, straining bolts etc with provision of binding wire complete including dismantling of existing fencing all as specified and directed. (Note: Chain link fence will be supplied under item No 39 below)

Supply only chain link MS galvanised fencing, 50mm x 50mm size with 3mm dia wire complete all as specified and directed

M&L for two coats of synthetic enamel paint over a coat of Red oxide primer including preparation of new steel/iron surface of any description over 10 cm in width or girth complete all as specified and directed

Taking down up or down steel tubing and connections incl cleaning for re-fixing or removal to stores ,15mm dia pipes complete all as specified and directed.

Ditto all as per item No 41 above but 20mm dia pipes.

Refixing of old serviceable 15 mm bore of steel tubing pipe take out from item No 1 and conection in new or old position on wall, cieling, floor etc complete all as specified and directed.

Ditto all as per item No 43 above but 20mm dia pipes take out from item above

S&F galvanised mild steel medium grade tubes 15mm dia bore with all fittings and fixed to wall , floor etc. complete all as specified and directed.

Ditto all as per item Ni 45 above but 20mm dia pipes.

S&F in repairs Bib tap 15mm dia standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed (Minimum weight 15mm-90gms/20mm-125gms).

S& F in repairs Stop valve 15mm dia of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed (Minimum weight 15mm-90gms/ 20mm- 92gms)

S&F in repairs for Brass chromium plated shower rose 125mm size complete all as specified and directed and sample to be approved by Engr-in-charge.

S&F in repairs for PVC flushing cistern valve less, syphonic action type low level, ball valve, float and handle with bracket fixed in repair of 10 ltrs capacity all as specified and directed including taking down old one complete all as specified and directed

S&F in repairs for Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern including necessary cutting to floor tiles and connection to WC complete all as specified and directed

S&F in repairs PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed

S&F in repairs Vitreous China wash basin, white, flat back, size 550x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets ,fixed in repairs complete all as specified and directed

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed , screwed for iron pipe of bore 15 mm fixed in repairs complete all as specified and directed

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F in repairs Waste coupling of PTMT (half or full threaded) (Minimum weight 40 mm-45gms/40mm-60 gms) for 32mm bore dia pipe complete all as specified and directed

S&F in repairs Waste coupling of PTMT (half or full threaded) (Minimum weight 40 mm-45gms/40mm-60 gms) for 40mm bore dia pipe complete all as specified and directed

S&F in repairs doom grating 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed

S&F in repairs Grating doom 125/100 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified and directed

S&F in repairs Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe 50mm bore of pipes

Taking down chowkhats or frame not exc 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed

M&L Solid PVC door frame of size 50x47mm ,made out of 5mm plain colour PVC sheet re inforced with MS square tube ,supplying and fixing in opening complete all as specified and directed

M&L Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed

S&F 100mm butt hinges cold rolled mild steel medium weight and fixed complete all as specified and directed

S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F Aluminium anodised barrel tower bolts of extruded section 100mm long complete all as specified and directed

S&F 300 mm long aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections complete all as specified and directed

S&F in repair Water closet (Squatt pattern) vitreous China squatting pan, ‘Orissa’ pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) connection to trap and squatting pan including P' trap set in and including concrete etc. complete all as specified and direted by Engr-in-charge including making good to floor

S&F in repair wash down water closet (Pedestal pattern), white incl traps and all fittings complete all as specified and directed

Dismantling of cast iron 100 mm bore pipes jointed in cement motar complete all as specified and directed

Dismantling of cast iron 75 mm bore pipes jointed in cement motar complete all as specified and directed

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as specified and directed

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as specified and directed

S&F for 75mm bore dia PVC (SWR) bends with access door complete all as specified and directed

S&F for 75mm dia PVC (SWR) branch piece single(single Y) equal or unequal with access door complete all as specified and directed

S&F for 75mm dia PVC (SWR) vent cowl complete all as specified and directed

S&F for 100mm bore dia PVC (SWR) bends with access door complete all as specified and directed

S&F for 100mm dia PVC (SWR) branch piece single(single Y) equal or unequal with access door complete all as specified and directed

S&F for 110mm dia PVC (SWR) vent cowl complete all as specified and directed.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed

Excavation in trenches in Soft/Loose soil n. exe 1.5m wide & n. exe 1.5m depth for foundation etc n.exe 10sqm on plan and getting out in complete all as specified and directed

Demolition and breaking up drain pipes ( SWG,AC or RCC pipes ) set in CM 150mm dia complete all as specified and directed

M & L for providing bed to drain pipes 150mm dia in cement concrete (1:3:6) type C2 using 40mm graded stone aggregate including packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and directed

M & L for providing reinforced cement concrete pipes 150mm dia class NP 2 with collars laid and jointed with cement jointed complete all as specified and directed

M&L for Cutting into existing manholes for connecting new drains internal dia of pipe 150mm dia making good to pipe & rendering cutting out existing benching for forming branch channel (1/2 round or 3/4 section in cement concrete (1:2:4) type B-1, smooth finished complete all as specified and directed

Returning filling in including spreading levelling, watering & well ramming in layers n. exe 25cm complete all as specified and directed

Removing excavated material any type of Soil n. exe 50m and depositing where directed by Engg-in- charge at a level n. exe 1.50m above the starting point in complete all as specified and directed

M & L for providing plain cement concrete 1:2:4 type B1 using 20mm grade agg. as in surfaces channels & drains complete all as specified and directed

M & L for providing plain cement concrete 1:2:4 type B1 using 20mm grade agg. as in coping including weathering slightly, rounded or chamfered angles and throating and necessary use and waste of form work complete all as specified and directed

Prem Singh

Harish Enterprises

Sunil Constructions

Pranjal Associates

Sayili Enterprises

Sky Vision Construction

Mehta and Co.

R & Y CONSTRUCTION COMPANY

AVS CONSTRUCTION

OM GANESH CONSTRUCTION