PROVISION OF SECURITY FENCE TO FASF, OLD VALLA ASTRIDE NH-3(APPROX 600 MTR) AND SPECIAL REPAIR OF OTM BLDG NO- 01 OF NO 6 DET WCLU AND TOILET BLOCK IN BUILDING NO P-41(A) MDC UNDER GARRISON ENGINEER AMRITSAR CANTT

Amount

15 ID/ALBW(ASR)- 01/2023-24 Excavating in post holes in soft/loose soil each not exc. 0.50 cum and getting out , returining filling and ramming earth or broken rubble mixed in layer not exc 25 cm ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing rolled mild steel sections ( angles, tees etc ) as in post and Ties fixed with angle cleats, MS plate etc including necessary welding etc ; Complete all as specified and directed by Engineer-in-charge. ( Fe-410 w gde E-250)

Material and Labour for PCC (1:3:6) type C-2 using 40 mm graded aggregate as in foudation Filiing Etc ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for applying two coats of synthetic enamel paints to steel surfaces over a coat of red oxide primer over 10 cm width or girth ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing pre-painted galvalume aluiminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MS Screw bolts(machine made)with haxagonal or square heads at one end and screwed the other or screwed both ends each screwed to be fitted with washer and one haxagonal or square nut not exceeding 5cm long dia of shank 5 to 10mm.; Complete all as specified and directed by Engineer-in-charge.

(Job No-AC/SRW (BLDG)-01/ 2023-24) Dismantling Brick tiles or terracing tiles, single layer on roofs ; Complete all as specified and as directed by Engineer-in-Charge.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in padding concrete fair finish, roof kerbs or mud stops, rounded or chamfered on edges and like including weathering slight rounded and throating ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing (minimum) 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application over entire roof area with over lapping 100mm to either sides and sealed in after cleaning down the roof by brooms ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for 40mm thick brick tiles, laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for brick tiles, but except brick tiles ( Note:-Old serviceable tiles shall be reused) laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement ; Complete all as specified and as directed by Engineer-in-Charge.

Disconnecting existing tanks 1000ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc ; Complete all as specified and directed by Engineer-in-charge.

Disconnecting existing tanks 500ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc ; Complete all as specified and directed by Engineer-in-charge.

Taking down Chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters ( without taking off shutters from the frames) ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing powder coated aluminium frame for doors ,windows, ventilators with one or more rebates including joining cleats for fixing complete all as specified and directed by Engineer-In-Charge.( Min. thickness of powder coating 50 micron)

Supply and Fixing Anodised aluminium grill of approved design/pattern, with approved standered section and fixed to the window frame with CP brass/SS screw@ 200mm c/c, including cutting the grill to proper opening size for fixing and opration of handle and fixing approved anodised aluminium section around the opening all complete as per requirement and direction of Engineer-in-charge.

Supply and Fixing powder coated Anodised aluminium sliding window shutters or side hung type, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as roller, locking arrengment, peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as required at site all as directed by Engr-in-charge. Note: Glass and wire mesh shall be measured and paid separately.

Supply and Fixing Sheet glass, 4.00mm thick ordinary quality, in squares,not exceeding 0.50 sqm in each pane including rubber packing and aluminium beading with and incl solar control film 25 Micron reflective type sticked to glass panes as per instructions of manufacturer s; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing stainless steel wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples ; Complete all as specified and directed by Engineer-in-charge.

AC/SRW(BLDG)-02/2023-24 Taking down cement plaster on brick, concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Of any description ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 15mm thick cement plastering in cm 1:6 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 10mm thick cement plastering in CM 1:3 on ceiling surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 15mm thick cement plastering in cm 1:4 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plaster surface and applying two coats of white wash on wall ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plaster surface and applying two coats of white wash on ceiling surfaces ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of newly plastered surface of wall and applying two coats cement base paint over a coat of primer to match the existing treatment ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old decorated brick concrete, plastered/unplastered surfaces of walls pillars cornices by brooming down with steel wire brushing scrapping down smoke soot, moulds moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on the walls pillars, cornices etc. ; Complete all as specified and directed by Engineer-in-charge.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats ) ; Complete all as specified and directed by Engineer-in-charge.

Taking down chowkats with shutter exc 1.50sqm but n.exc 4Sqm (without taking off shutter for the chowkats ) ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Factory made single extructed WPC but frame size 50x 100 mm (wood polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum,screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2,modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Factory made single extructed WPC (wood polymer Composite) solid Plain flush door shutters of 30 mm thick comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minumum dencity of 650 kg/ cum and screw withdrawa strenth of 1800 N (Face )&900 N (Edge), minimum compressive strength of 50 N/mm2,modules of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/moisture proof and fire retardant and fixed with steelness steel butt hinges of requred size with necessary full body threank SS screw ; Complete all as specified and directed by Engineer-in-charge. ( steelness srew and butt hinges and necessary SS Screw shall be paid separatly)

Supply and fixing10 mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet Suitably placed fixing in Aluminium door etc ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Anodised aluminium frame for doors,windows,ventilators,side hunge one or more rebates including necessary jointing cleats,glazing clips, ruber neoprene packing anodised aluminium snap beading screw Tee etc section for weighing not less than 1.4 kg/RM ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing powder coated(Min thickness of powder coating shall be 50 micron) aluminum windows shutter of size min 18mmx50mm for sliding type windows of standard tubular sections of approved make having glazed panels or glazed and gauzed panels of appropriate size running on seperate tracks in the channel conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. All the panels shall be of appropriate size having overlaps as required and including all required beadings, clips, rollers, rubber gaskets, cleats,complete and powder coating in approved shade and colour. Note:- Each panel shall be measured separetely. Glass pane and wire mesh shall be measured and paid separetely.

Supply and Fixing 5.5 mm thick sheet glass ordinary quality in square or rectangular in size n.exc .5 sqm each in aluminium door or window shutter including taking out old damaged glass pane ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing powder coated anodised aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc(Thickness or powder coating not less than 50 micron) ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing figured glass pin head type, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing for aluminium door & window, aluminium wire cloth, .36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Floor door stopper aluminium ally body and tongue anodised of size 140 mm etc ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Aluminium, anodised, barrel tower bolts 150mm of extruded section and fixed ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 125 mm long Aluminium handles, cast type anodised ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing stainless steel butt Hinges, 100mm size, medium weight, cold rolled mild steel ; Complete all as specified and directed by Engineer-in-charge.

Dismantling water tanks and Supply & Fixing rotational moulded polythene water storage tanks of 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs stop value 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-charge.

Taking up and down GI pipe15mm bore including fittings, connection, including cleaning for refixing in any position ; Complete all as specified and directed by Engineer-in-charge.

Taking up and down GI pipe20mm bore including fittings, connection, including cleaning for refixing in any position ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings incl taking down ISI marked ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings incl taking down ISI marked ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule and fixed in repairs ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs stop valves(Concealed cock) 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs angel valves 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs vitreous China Squatting pan 'Orrisa' pattren size 580x440mm white with integral foot rest and PVC(SWR) 'P' trap 110/110mm bore; Complete all as specified and directed by Engineer-in-charge.. Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately.

Supply and Fixing of Vitreous china wash down water closet pan( pedestal pattern), white with PVC(SWR) 'P' trap 110/110mm bore ; Complete all as specified and directed by Engineer-in-charge.. Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately.

Supply only 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flote handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia; Complete all as specified and directed by Engineer-in-charge.

Supply only Plastic water closet seat,white/ivory,closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (Toilet Seat Cover) ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing Chromium plated Health faucet in repairs with 1 metre long chain ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing sheet glass shelf assembly 60 cm oval shape consisting 5.5 mm thk 8mm thk glass with brass bracket including stainless steel railing, fixed to wall as ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minium weight 190 gms) ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixinf approved anodised aluminium standard section around the opening, all ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs viterous chinaware wash hand basin light colour/white of size 550x 400cm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets,32mm bore PVC waste pipe of appropriate length ilcluding taking out of old WHB & making necessary connections ; Complete all as specified and directed by Engineer-in-charge.

Dismantling structural steel work in any work ; Complete all as specified and directed by Engineer-in-charge.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 110mm bore PVC (SWR) ISI marks pipes single socketed in any length with rubber ring joints fixed to wall or floor ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor height ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC (SWR ) bends 75 mm bore any radius ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC (SWR ) vent cowl 110 mm bore ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for PVC (SWR ) floor trap 110/75 mm plain with grating incl. jointing with solvent cement as per site requirement ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Stack clamps (110 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Stack clamps (75 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof ; Complete all as specified and directed by Engineer-in-charge.

Demolation of brick work built in cement mortar or cement lime mortar as cutting, opening of exsiting wall ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for brick work with sub class 'B' bricks straight curved on plan exc 6 mean radius built in CM 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Demolition of Stone slabs and tiles of laid, beded and pointed of any mortar in any description or thickness in floors, aprons etc. ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Granite (of any type) work (table rubbed and polished) 20 mm thick in steps , jambs, pillars, window cills, cooking plateforms and like in cemnet mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 ; Complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection finishing the surface even and fair ; Complete all as specified and directed by Engineer-in-charge.

Dismantling of brick tiles single layers on roof, jointed and grouted / pointed in cement mortar including cleaning serviceable tiles and stacking properly for re-use, disposal of unserviceable tiles and debris /rubbish from site ; Complete all as specified and directed by Engineer-in-charge.

Demoliton of mud in roof any thickness including mud plastering and removing to distance exc 250m but n exc 500m ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs, sloping padding and finishing the surface even and smooth (without using extra cement) ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm includingcleaning surfaces etc ; Complete all as specified and directed by Engineer-in-charge.

Material & Labour for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces by forced application over entire roof area, sunken portion with overlapping 100mm to eiher side; Complete all as specified and directed by Engineer-in-charge.

Material and labour for 40 mm thick brick tiles laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 mixed with 5% of crude oil by weight of cement ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for brick tiles but except tiles( Note : (i) Serviceable brick tiles obtained from dismantling shall be reused )laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 mixed with 5% of crude oil by weight of cement ; Complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for joint free Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm to 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for glazed ceramic coloured tiles in vertical surface of size 600x1200x8 mm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles ; Complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (Reinforcment) of any description ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for RCC in 1:2:4 type B-0(using 12.5 mm graded stone agg) as in chajjas facia, shelves, lintel etc and similar work; Complete all as specified and directed by Engineer-in-charge.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 10mm dia over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securing with clips ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 110mm PVC (SWR) bends any radius with access door ; Complete all as specified and directed by Engineer-in-charge.

Supply & Fixing vitreous china urinal half stall type with CP spreader white incl CP waste coupling with grating and union fordischarge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for two coats of synthetic enamel painting on steel surfaces of any description over 10 cm in width or girth not otherwise described above priming coat of red oxide including prepration of previously untreated surfaces ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for plain cement concrete( 1:3:6) type C-2 using 40mm graded stone aggregate as in surface channel and drains ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for sub class B bricks (old size) laid on edge on floor straight or curved on plan exceeding . 6 metre radius bedded and jointed in CM 1:6 and pointed in CM 1:3 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for brick work in sub class 'B' bricks old size brick straight or curved on plain in half brick thick wall in CM (1:4) for sides of drain etc. ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for flush pointing to brick wall of drains in CM (1:3) ; Complete all as specified and directed by Engineer-in-charge.

Extra for forming fair finised drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds mitred/stopped ends etc ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for applying two coats of white wash on wall including preperation of newly plastered surfaces ; Complete all as specified and directed by Engineer-in-charge.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, sockets, lamp holders, brackets, bulk head fittings, tube light fittings etc. and making good disturbed surfaces of walls etc. as per existing finishes by plastering, repairss and white / colour wash etc.; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing point wiring for one light point / fan point / bell point / 5 Ampere socket outlet point (independent point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated 1.50 sqmm size copper conductor cable as in earth wire and connected to common earth dolly ; Complete all as specified and directed by Engineer-in-charge. One light/one fan/one bell point controlled by one, one way switch.

Supply and Fixing point wiring for one 5 Ampere socket outlet point (independent point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated 1.50 sqmm size copper conductor cable as in earth wire and connected to common earth dolly ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing point wiring for one 5 Ampere socket outlet point (same point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated 1.50 sqmm size copper conductor cable as in earth wire and connected to common earth dolly ; Complete all as specified and directed by Engineer-in-charge.

All as per item here in before but wiring with using cable 4.0 sqmm FRLS cable and 4.0 sqmm cable earth continuity wire for one 3 pin socket outlet, 16 Amperes on independent board.

Supply and Fixing Modular switch 6 Amp 1 way 1 module size ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing Modular switch 16 Amp 1 way with indicator 1 module size ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing Modular socket shuttered 6 Amp 2/3 pin combined 2 module size ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing Modular socket 16Amp multipurpose type 2 module size ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing Ceiling rose, PVC / Polycarbonate . Isolated body with face Bakelite 65 x 50 mm 3 terminal, 240 volts, 5 Amps with back plate ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing sheet metal enclosure for DB’s (Double door type) , single pole and neutral, 8 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wall with IP-43 and IK-09 protection ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing MCB single pole, 240 volts, 5 to 32 Ampere, rupturing capacity 10 KA, ‘C’ curve type ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing MCB double pole, 240 volts, 32 Ampere, rupturing capacity 10 KA, ‘C’ curve type ; Complete all as specified and directed by Engineer-in-charge

Material and Labour for sub main wiring with PVC insulated, 1100 volts grade single core multistranded copper conductor cable conforming to IS specifications, 2 runs of 4 sqmm single core multistranded copper conductor PVC insulated cables as neutral continuity conductor drawn through and including one run of 4 sqmm multistranded PVC insulated FRLS , copper conductor cable as earth continuity conductor incl 25mm dia rigid PVC conduit and conduit accessories fixed on wall/ceiling etc., or concealed in wall and connecting to common earth dolly including taking down all sub main wiring ; Complete all as Specified and as directed by Engineer-in-Charge.

Supply & Fixing for LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose including taking down ; complete all as specified and directed by the Engineer in Charge.

Supply and fixing Dusk and down LED roadway luminaries 45 Watt 230 V AC outdoor type with epoxy black powder coated sheet , high pressure die cast aluminium housing and heat resistant complete with dryer , lamp bracket of suitable size with impact and corrosion resistant including thermal managment in multiple optics complete with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fittings complete and testing incl taking down old one ; Complete all as specified and directed by Engineer-in-charge

Supply and Fixing fresh air fan 250mm size incl making of hole in wall of suitable size to fixed/grouted the exhaust fan with suitable bolts , nuts etc and connecting up with & including 3 core flexible copper conductor cable from ceiling rose to fan ; complete all as specified and directed by the Engineer in Charge.

Supply and Fixing or passing through and incl GI pipe 1100 Volts, heavy duty stranded conductor cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sqmm 2 core nominal cross section in service connection ; Complete all as specified and directed by Engineer-in-Charge.Note

Material and Labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note : - (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt. (iii) Earthing work will be done by contractor ub presence of JE /Engr-in-Charge, the earthing work carried in absence JE /Engr-in-Charge will not neasured & paid for the same. (iv) All earthing material will be approved before bulk procurement and got approved from Engr-in-Charge

Supply and Fixing Automatic Hand dryer infrared sensor high jet ; Complete all as specified and directed by Engineer-in-charge

J S S BUILDERS & ENGINEERS

ESS KAY BUILDER

M/s. M Company