SPECIAL REPAIRS TO BLDG NO. OWT-190, 189, 49 AND 48 (COOK HOUSE AND DINNING HALL) OF AVN SQN AND PROVN OF CERTAIN REVENUE WORKS AT LKB MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Taking down Shutter of any description, not exc. 1.00 Square Each, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Steel Sheeting, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Hacking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Fittings, segregating Serviceable Pipes & Fittings, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Fittings, segregating Serviceable Pipes & Fittings, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Surface Excavation not exc. 30 Cm Deep and averaging 15 Cm Deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation in Over Areas, not exc. 1.50 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Over Areas, Depth exc. 1.50 Metre but not exc. 3.00 Metre and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) to a distance not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

M&L Sand Filling under Floors or in Foundations including Watering and Consolidation in layers not exc. 15 Cm thick, complete all as specified and as directed.

M&L Hardcore Broken Stone or Boulders, gauge not exc. 63mm, deposited, Spread and Levelled in layers not exc. 15 Cm thick, Watered and Well Rammed to a True Surface, complete all as specified and as directed.

M&L Loose filling with Broken Bricks Aggregates of gauge 80mm to 150mm in Soakage Pits, Soakage Wells, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Roof Beams, Lintel Bands, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns; in Floors, Roofs, Landings Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Landings, Cover Slabs, Manhole Cover Slabs, etc., Set in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid separately under relevant Item.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) in Coping, Bed Plates, Benching, Holdfast, Bed Block, Kerb Stones, etc. including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry (Honey Combing) with Solid Blocks in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and setting in Cement Mortar 1:4, complete all as specified and as directed.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams and Similar Work; Square, Rectangular or Polygonal, Vertical or to Batter, Rough Finished Surface of Concrete Flat, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc, Rough Finished Surfaces of Concrete Flat, complete all as specified and as directed.

M&L Formwork to Soffits of Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Work not exc. 200mm thick (Horizontal or Sloping) Rough Finished Surface of Concrete Flat, complete all as specified and as directed.

M&L Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Concrete Railings, Openings in Concrete Walls, Floor and Roofs not exc. 20 Cm Wide and Sides of RCC/ PCC Bands in Walls, Horizontal or Sloping and Similar Work, exc. 5.0 Cm but not exc. 10 Cm Wide, Rough Finished Surface of Concrete Flat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectangular or Triangular in Section, exc. 13 Sq Cm but not exc, 25 Sq Cm, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned), Plain Fillets, Wrought, Square, Rectangular or Triangular in Section, exc. 6.0 Sq Cm but not exc, 13 Sq Cm, fixed with Screws, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

M&L Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and wood grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet beading used inside Stiles and Rails and decorative PVC Beading of 10mmx10mm (90) and jointed together with Solvent Cement and fixing in the Frame at Site with and including Stainless Steel Hinges, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle and Steel Peg Stay, complete with Glazing Bars, dovetalied or welded, complete all as specified and as directed.

S&F Steel Ventilator with Centre Hung Shutter including 2 Pairs of Brass Cup Pivots, Catch Spring and Pully Wheel and fixing, complete all as specified and as directed.

S&F Steel Ventilator with Top Hung Shutter including Hinges, Steel Peg Stay and fixing, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt 125mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt 150mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 75mm in size (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 100mm in size (as approved), complete all as specified and as directed.

S&F Aluminium Handle 125mm (as approved), Fabricated type, anodised, complete all as specified and as directed.

S&F Aluminium Handle 150mm (as approved), Fabricated type, anodised, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

S&F Floor Door Stopper (as approved) having Overall Length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

M&L Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

M&L Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and Fixed-in-repairs, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Sheet Glass 4.0mm thick, Frosted quality and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane and fixing to Wooden/Steel Windows, Ventilators, etc., complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Rolled Mild Steel in Joist, Channel, Angle, or Tee Sections in Vertical Post, conforming to Fe-410-W (Gde E-250) Quality 'B', fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or Other Connecting Plates, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or notched (Ordinary and Counter Sunk) forming Holes, without any attachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Hand Rails, Half Round or Other Stock Section or Core for Wooden Hand Rail Straight Portion, drilled and counter sunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embeding in Concrete and screwing etc; Wind Ties for Roof including securing Bolts, Posts and Struts in Fencing including cutting Tops to Shape as directed, drilling Holes, Notching for Wire, etc.; Flat Iron Fillets (for securing Wire Mesh, etc.) including all necessary drilling, bolting or riveting, etc. and Similar Work, conforming to Fe-290 Gde, E-165, complete all as specified and as directed.

M&L Framed Work in Doors or Gates of Angle or Other Section with Gusset Plates, Rails, Braces, etc., conforming to Fe-290, Grade E-165, drilled for fixing of Steel Sheeting or Other Covering. Doors, etc. to be prepared for Hanging or Sliding with and including either Hooks and Hinges or Steel Hanging Door Fittings (exclusive of Steel Sheeting or other Covering, Running Rails & Guides), hanging also fastening and fixing, complete all as specified and as directed.

M&L Framed Work such as Grills, Gratings, etc, with Ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars, Barred Iron Doors, Ladders, Framed Balusters, Walkways, Railings, Frame Work of Water Tanks and Similar Works, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Welded Steel Wire Fabric, not exc. 4.0 Kg/Sqm and fixed complete to Steel Members, complete all as specified and as directed.

S&F Mild Steel Plain Black Sheet 0.80mm thick in Wall Cladding, Steel Gates and Similar Work, cut to Size, Holes punched; including Round Headed Screws, Clout Nails or Rivets and fixed to Wood or Steel Framing with Plain 40mm Lap Joints with riveted or welded Seams including bending or turning up, mitred angles, etc. as required, complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 275 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Refixing Corrugated Mild Steel Sheeting 0.63mm thick (Serviceable Steel Sheets obtained from Item No. 1.006 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 275 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Refixing Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick (Serviceable Galvalume Sheets obtained from Item No. 1.006 here-in-before) in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L GI Frame Work for Seamless Ceiling comprising of GI Perimeter Channnel 0.55mm thick with 2 Unequal Flanges of 20mm and 30mm and Web of 27mm fixed to surrounding Wall using Nylon Sleeves and Screws at 450mm Centre to Centre, Intermediate Channel 0.9mm thick having 2 Equal Flanges of 15mm Each and Web of 45mm suspended from Soffit at approx 900mm Centre to Centre with Gl Cleat and Steel Expansion Fasteners with and including Ceiling Section (not exc 1.20 Metre length) of 0.55mm thickness having Kurled Web of 50mm and Flange of 26mm Each with Lips of 10.5mm fixed to the Intermediate Channel with Connecting Clips across the Intermediate Channel at 457mm Centre to Centre, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to GI Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Flooring, Pavings, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Floors, etc., finished Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Roughening Surfaces of Old Concrete Floor by Picking, Sweeping Clean and Washing down with Water to remove Dust, etc., and Brushing with Neat Cement Slurry @ 3.0 KG/SQM on Cleaned Concrete Surfaces, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Joint Free Tiles 7.0mm to 8.0mm thick (Square/ Rectangular) area of Each Tile exc. 0.06 Sqm but not exc. 0.11 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Non-Skid Ceramic Coloured Joint Free Tiles 7.0mm to 8.0mm thick (Square/ Rectangular) area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rectan-gular) area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Glazed Ceramic Coloured Tiles 300x200x6.0mm-7.0mm thick (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Joint Filling in Plinth Protection, etc., not exc. 6.0mm in Width with 1 Part of Bitumen and 3 Parts of Sand, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick/PCC Blocks or Concrete Works including mixed with WPC, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Ceiling and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (as approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (as approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of Cement Based Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted AC Boards Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel Sheets on Roofs, Walls, etc. of any descrip-tions, over exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade), complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Stencil Writing Letters or Figures (Block. Roman, Italic or Indian) of Height exc. 150mm and not exc. 200mm with White Synthetic Enamel Paint on Black Base Painted Surfaces, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Connections/ Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Connections/ Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butterfly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Chromium Plated Wall Flange and Fixed-in-repairs (if ordered) complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Angle/ Stop Cock/ Valve 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F Gun Metal Gate Valve 20mm bore (dia) with Iron Wheel Head including Flange, screwed both Ends for Iron Pipe, complete all as specified and as directed

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, hoisted and fixed in Position all as specified in MES Schedule and Re-connecting Water Supply Connections including Lowering down unserviceable Water Storage Tank after disconnecting of Water Supply Connections, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, hoisted and fixed in Position all as specified in MES Schedule and Re-connecting Water Supply Connections including Lowering down unserviceable Water Storage Tank after disconnecting of Water Supply Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), High Pressure with Epoxy coated Aluminium Rod & High Density Plastic Ball (minimum Weight 210 Gram), screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/ Distrubed Surfaces, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) 'P' or 'S' Trap and Fixing Bolts and Making Good to Floors and distrubed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device, complete all as specified and as directed.

S&F Stainless Steel Jet Spray (Butter-fly or 'L' Bend) Chromium plated, suitable for EWC including 1.0 Metre Tube with necessary Nuts, Bolts, complete all as specified and as directed. MAKE : PRAYAG, Model No. DROPLETS, Cat No. BEA-17 (Butter-fly type) & BEA-18 (L-Bend type) or Make as approved by GE

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, and PVC Flush Pipe 32mm bore (dia), a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back) with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Distur-bed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Kitchen Sink with Drainage Board made of Stainless Steel l.0mm thick of Overall size 915x460mm having Bowl size 410x330x160mm with Plugs, Washers and Stainless Steel Waste Fittings, etc. including bedding in Cement Mortar to Dwarf Wall or including fixing Cantilever Brackets and Connecting Union to Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Waste Pipe 32mm/40mm bore (dia) suitable for Wash Hand Basin, Sinks, Urinals, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size with PTMT Nuts of Length 450mm and Fixed-in-repairs (if ordered), complete all as specified and as directed.

M&L Corner Glass Shelf 200mm with ABS Brackets, complete all as specified and as directed. MAKE : PRAYAG, Model No. ABS BRACKETS, Cat No. BEA-48 or Make as approved by GE

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair) and Fixed-in-repairs (if ordered), complete all as specified and as directed.

S&F Stainless Steel Grating Doom of Size 75mm dia with Waste Holes, Chromium Plated (as approved) and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Grating Doom of Size 100mm dia with Waste Holes, Chromium Plated (as approved) and Fixed-in-repairs (if ordered), complete all as specified and as directed.

M&L PVC (SWR) Floor Trap, Diameter of Outlet 75mm, Plain with Grating and jointing with Solvent Cement, complete all as specified and as directed.

M&L Cast Iron Floor Trap, Diameter of Outlet 75mm with Grating and jointing to Waste Pipe fixing in Cement Concrete type 1:2:4 (20mm graded stone aggregate) and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Pipe 75mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, fixing to Walls, complete all as specified and as directed.

S&F PVC (SWR) Pipe 75mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia) of any type, provided with Access Door, etc., jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia) of any type, provided with Access Door, etc., jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 75mm bore (dia), jointing with Solvent Cement, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Bed to PVC (SWR) Drain Pipes 160mm bore (dia), laid to Falls, including Packing Under and Completely Surrounding Pipes with Concrete after they are laid and tested; complete all as specified and as directed.

S&F PVC (SWR) 160mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches, complete all as specified and as directed.

M&L Cutting into existing Manholes for Connecting PVC (SWR) Pipes of 160mm bore (dia), Making Good to Pipe and rendering, cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, etc. but except Light Fittings of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White Washing/ Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down/out unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treat-ment (White Washing/ Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping will deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Casing Capping only. Wires required for looping, etc. as ordered will deem to be include in the Quoted UNIT RATE.

S&F PVC Rectangular Block of size 100x100x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/ out unserviceable PVC Block (if ordered), complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 5-in-1, Multi Plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F LED Lamp 7 Watt, 230 Volt (as approved) including Taking down/ out unserviceable Lamp of any description (if ordered), complete all as specified and as directed. MAKE : HAVELS, Model : LED ADORE 7 W E27 WW Ball Lamp or equivalent in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

S&F LED Bulk Head e-TATRA Series Light Fitting 1x6.0 Watt having Plastic Housing with Clear Prismatic Diffuser LED 6.0 Watt Lamp and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description (if ordered), complete all as specified and as directed. MAKE : C&S E-TARTA Series 6W or equivalent Model/ Cat No. in Make : BAJAJ/ CG/ HAVELS/ PHILIPS (as approved by GE).

S&F LED Bulk Head Light Fitting 1x10 Watt, Environment Friendly, Ultra Modern, Energy Saving, Surface mounted, comprising of High Brightness LEDs Light Source complete with all Accessories and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable, complete all as specified and as directed.

S&F LED Wall mounted Tube Light Fitting 1x10 Watt of Aluminum Housing having Integrated Electronic Driver with LED 10 Watt Tube and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable, complete all as specified and as directed. MAKE : BAJAJ/ CG/ C&S/ HAVELS/ PHILIPS (as approved by GE)

S&F LED Decorative Wall Light Fixture 1x10 Watt made of Polycarbonate with LED 10 Watt Bulb and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description, complete all as specified and as directed. MAKE : BAJAJ/ CG/ C&S/ HAVELS/ PHILIPS (as approved by GE)

S&F LED Integrated Batten T-5 Tube Light Fitting 1x20 Watt with LED 20 Watt and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description (if ordered), complete all as specified and as directed. MAKE : HAVELS E-LITE PRIDE PLUS 20W or equivalent Model/ Cat No. in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

S&F Ceiling Fan Regulator, Dimmer Switch type, 230 Volt AC, Rotary Stepped Electronic, 120/280 Volt including necessary Connection and connecting up, complete all as specified and as directed.

M&L Taking down Ceiling Fan, Exhaust Fan of any Make, Size after disconnecting and Keep in Safe Custody for Re-hanging/ Re-fixing, complete all as specified and as directed.

M&L Preparing Old Painted Surfaces of Fan including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Hanging/Fixing only Ceiling Fan, Exhaust Fan and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

M&L Exhaust Fan 300mm Sweep with Louver, 1400 RPM, Single Phase, 230/ 240 Volt AC, fixing with Mild Steel Bolts, Nuts, Washers, etc. and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable, complete all as specified and as directed.

M&L Exhaust Fan 450mm Sweep with Louver, Turbo Force 1400 RPM, Single Phase, 240 Volt AC, fixing with Mild Steel Bolts, Nuts, Washers, etc. and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable, complete all as specified and as directed.

M&L Cutting Holes in Walls of suitable size to fixing Exhaust Fan and Making Good to dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) including providing Surface Treatment to match the Existing/ Adjoining Surfaces, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (if ordered), complete all as specified and as directed.

S&F MCB Single Pole & Neutral 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (if ordered), complete all as specified and as directed.

S&F MCB Distribution Board Sheet Metal Enclosure, Double Door with Steel Phosphotised Powder painted, SPN, 4-way, 240 Volt, suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-going, complete with 200 Amp rated Neutral Bars & Earth Bar, Connecting Cable Links with Top and Bottom Removable Gland Plate complete with IP-43 Protection and connecting up, complete all as specified and as directed. MAKE : HAVELS/ LEGRAND/ L&T/ SCHNEIDER

S&F MCB Distribution Board Sheet Metal Enclosure, Single Door with Steel Phosphotised Powder painted, SPN, 4-way, 240 Volt with 200 Amp rated Neutral Bars & Earth Bar and connecting up including Taking down/out unserviceable MCB DB (if ordered), complete all as specified and as directed. MAKE : HAVELS, Cat No. DHDPSHOSRW04 or equivalent Model/ Cat No. in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

S&F MCB Distribution Board Sheet Metal Enclosure, Single Door with Steel Phosphotised Powder painted, SPN, 8-way, 240 Volt with 200 Amp rated Neutral Bars & Earth Bar and connecting up including Taking down/out unserviceable MCB DB, complete all as specified and as directed. MAKE : HAVELS, Cat No. DHDPSHOSRW08 or equivalent Model/ Cat No. in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

Supply & Laying or Passing through Pipe 1100 Volt grade heavy duty, Cross-sectional area 10 Sqmm, 2 Core, Flat or Circular Cable with PVC insulated Aluminium Conductor served with an inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed in Service Connection suspended by insulating Hangers not more than 1.0 Metre apart including 4.0mm Suspension Wire including Taking down/ out Unserviceable Service Connection (if ordered), complete all as specified and as directed.

M&L House Service Bracket (Hook type) complete with GI Pipe 40mm bore (dia), Medium grade, 3.0 Metre Long with 2 No. GI 40mm bore (dia) Bend 90°, Mild Steel hook and Stay or Guy, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description (if ordered), complete all as specified and as directed.

M/S. NOBIN RAJKHOWA

D. D. Construction

FREEZCON