ADDITION / ALTERATION AND SPECIAL REPAIRS OF CERTAIN BUILDINGS IN AGNIVEER LINES AT ARTY CENTRE UNDER GE NASIK ROAD CAMP

Amount

Taking down carefully existing bitumen tar felt incl. Screed and cleaning of surfaces of roof etc. With wire brush incl. Flashing and junctions of parapets/kerb walls etc. And removing of the rubbish to a distance exc. 500 metres but not exc. 1.5 km and deposting where directed.

M&L screed bed / bedding layer 10mm thick in cement mortar (1:3) on concrete surfaces mixed with water proofing liquid and smooth finished and smooth(without using extra cement).

Waterproofing on roof including flashing and junction of parapet, kerb, wall etc. As under (a) Applying oil based bituminous primer on cleaned and dried surface @ 0.2 kg/sqm. (b) Laying by thermo fusion ( torch applied) 3 mm thick APP based polymeric water proofing membrane weighing not less than 3.6kg/sqm and reinforcement with polyester non woven fabric ( not less than 150 gms/sqm) (c) Painting the exposed APP membrane surface with bituminous aluminium paint @ 0.15kg/sqm (Note: Material for Ser No. (a), (b) & (c) above shall be of same approved make)

Supply only liquid water proofing compound

Disconnecting existing tanks, setting aside (or lowering if required) for repairs exc 500 n exc 1000 litre, cleaning, etc. and hoisting if required reconnecting and refixing in position. (Cleaning repairing, etc. measured separately)

M&L for type B1 (1:2:4) (20 mm graded aggregate) cement concrete in roof kerbs or mud stops, rounded or chamfered on edges

Dismantling water tanks of capacity Exc 500 Ltrs but n. exc 1000Ltrs and removing to from site or to store complete all as specified and directed.

S/F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 ltr hoisted and fixed in position .

S&F 20mm bore dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule

S&F in repairs Ball brass valves, high pressure, with polythene float and flynut for 20 mm bore dia pipe complete,screwed for iron pipe or brass ferrule and fixed

S&F 15mm Gun metal,globe or gate valves,with iron wheel head,screwed both ends for iron pipe

S&F 20 mm Gun metal,globe or gate valves,with iron wheel head,screwed both ends for iron pipe

S&F in repair 15mm Gun metal,globe or gate valves,with iron wheel head,screwed both ends for iron pipe

S&F in repair 20 mm Gun metal,globe or gate valves,with iron wheel head,screwed both ends for iron pipe

Taking up or down tubes galvanized iron and connections and removing/shifting from site incl cleaning where directed complete all as specifed and directed

(a) 20 mm dia

(b) 15 mm dia

Re-fixing only tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixing new fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size complete all as specified and directed

(a) 20 mm dia

(b) 15 mm dia

S/F for tubes medium grade, galvanized with iron all fittings fixed to walls, ceiling and laid in floor of sizes complete all as specified and directed :-

(a) 20 mm dia

(b) 15 mm dia

Taking down chowkat or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4 sqm each.

Taking down chowkat or frames with shutters (without taking off shutters from the frame) but n exc. 1.5 Sqm

Taking down shutters exc 1 Sqm but n exc 2Sqm

Taking down shutters but n exc 1.00 Sqm

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints

S&F for Factory made single extruded WPC (Wood Polymer composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x100 mm double rebate comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made Make : ECHON/Sintex/Rajshree/Navaratan Note : Rate of MS hold fast/Fasteners/SS Dash fastener deemed to be included in quoted rates .

S&F 28-30 mm thick Prelaminated Flush WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded side with wood grain texture with density not less than 650 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified

S&F 28-30 mm thick Prelaminated WPC factory made 100% Sketon/Glased door (conforming as per IS-4020) made from 100% lead free single extruded on both side with wood grain texture and with density not less than 650 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified

S&F for Factory made single extruded WPC (Wood Polymer composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm double rebate comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made Make : ECHON/Sintex/Rajshree/Navaratan Note : Rate of MS hold fast/Fasteners/SS Dash fastener deemed to be included in quoted rates .

S&F 30 mm thick moulded Prelaminated both side WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on front side with wood grain texture on front and plain on back side with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50N/ mm2, modulus of elasticity 850N /MM2 and resistance to spread of flame of Class A category with property of being termite/ bore proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S. screws, all as per direction of Engineer-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately) .

Material & Labour for painting with two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces exc 10cm width or girth including preparation of wooden surfaces all as specified and directed by EIC.

S&F aluminium alloy anodised sliding door bolt 300mm long with hasp & staple (bolt type) and fixing chops of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy complete all as specified and directed

S&F 100 mm Butt hinges,medium weight cold rolled Stainless steel all as specified & directed. approved by Engineer-in-Charge

S&F 75 mm Butt hinges,medium weight cold rolled Stainless steel all as specified & directed. approved by Engineer-in-Charge

S&F stainless steel tower bolt 200 mm long complete all as specified and directed approved by Engineer-in-Charge.

S&F stainless steel tower bolt 100 mm long complete all as specified and directed approved by Engineer-in-Charge.

S&F 150 mm stainless steel handels pull type complete all as specified and directed approved by Engineer-in-Charge.

S&F 100 mm stainless steel handels pull type complete all as specified and directed approved by Engineer-in-Charge.

S&F 1st class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed

S&F aluminium floor door stoppers double legged with hard drawn steel spring fitted in floor complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises.

M&L for joint free coloured non skid ceramic tiles 7mm to 8mm thick area of each tile exc 0.06 sqm but not exceeding 0.11 sqm thick set and jointed in neat cement slurry nd pointed in coloured cement to match in floor etc complete all as specifed and directed Note : Cement mortar screed bed layer shall be measured & paid separately

M&L for coloured glazed ceramic tiles 600x300x 7-8mm thick in vertical surface, set and jointed in neat cement slurry & pointed with white or coloured cement to match

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for 15mm thick Screed bed or bedding layer in cement mortar 1:6 for laying floors finishes

M&L for 10 mm thick rendering in CM 1:4 on brick masonary or concrete rough finished surfaces as backing coat

Dismantling of stone slabs of any descripation or thickness in floors, aprons etc laid bedded & pointed in any mortar complete all as specifed and directed

S&F Machine cut kota stone slab 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specifed and directed

M&L for Kota stone slab 10-15mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with gray cement slurry with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L granite (of any type)work (table rubbed and polished)18- 20 mm thick in steps,jambs,pillars,cooking platforms and like in cement mortar 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite

M&L for hand cut cudappa stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete Note: screed bed layer measured seperately complete all as specifed and directed

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similar work

M&L for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate as in floor concrete complete all as specifed and directed

M&L Screed bed or bedding layer of cement mortar 20 mm thick for laying floors finishes in cement mortar 1:6 complete all as specifed and directed

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as directed by Engr-in-charge

M&L for preparation of new steel surfaces and applying two coat of synthetic enamel paint over one coat of red oxide primer on new steel surfaces, girth or width n exc 10cm

S&F Sheet glass ordinary quility 3 mm thick n exc 0.5sqm each pane and glazing with oil putty complete all as specifed and directed

S&F Sheet glass ordinary quaility 3 mm thick n exc 0.5sqm each pane and glazing with oil putty incl hacking out old glass from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specifed and directed

Supply & Fixing stainless steel curtain rails of 25mm dia metre stops, rollers etc all as specified and directed.

Supply & Fixing stainless steel brackets of 25mm dia metre stops, rollers , hooks with fancy knob etc all as specified and directed.

S & F CP soap dish complete all as specified and as directed by Engr-in-Charge. Make Cera Code No- F5015106CH or equivalent in Jaquar, kohlar, grohe and Roca

M&L for special treatment to sunken portion with 10 mm thick plaster in CM 1:4 with WPC liquid conplast 421 and applying one coat each of Nitoproof 100 & Nitopro 120 on plastered surface . Rendering again 10 mm thick plaster in CM 1:4 mixed with complast 421 in sunken portion of WC & CI/PVC pipes joint shall be filled/jointed with mixture of cement fine sand and nitoproof 130 and provided hole in the wall & fixed 600 mm long 20 mm dia spout light grade & 1:3:6 C2 filling , floor area of wc upto 1.5 Sqm etc complete all as specified and directed.

Repairing broken edges of RCC chajjas, roof projections, fins, facia and similar works by dismantling of loose and damaged/ disintegrated portion of edges (cross sectional area not exceeding 150 sqcm) and cement mortar 1:4 or cement concrete 1:1½:3 type A0 and chicken wire mesh with nails (to hold fresh mortar/concrete) including necessary formwork etc. and scaffolding for work upto four storied buildings and finishing the surface by white wash or cement base paint to match the surface with existing work.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed

S & F pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated of approved profile steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa AZ 150 as in roof covering/cladding to wall fixed with self tapping screws with washer complete all as specified and directed

S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa AZ150 as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

S&F rolled mild steel Joist, channel, angle, flat sections, fixed independently, without connecting plates, or M S tubular sections etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) grade Fe 290( E-165) all as directed by Engr-in-charge

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-290 (Gde E 165)

Mild steel screw bolt (Machine made ) with hexagonal or square heads at one end and screwed the other, or serewed both ends, each screwed end to be fitted with washers and one hexagonal or squqre nut, but length of bolt exc 5 cm and n exc 10 cm long and dia of bolt 5 to 10 mm complete all as specified and as directed.

Dismantling framed work timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

M&L for preparation of new steel surfaces and applying two coat of synthetic enamel paint over one coat of red oxide primer on new steel surfaces, girth or width exc 10cm complete all as specified and directed

M&L for filling of gap portion of gable wall with PCC (1:3:6) or brick in cement mortar of any height upto 150mm thickness filling with suitable arragement of shuttering & formwork all as specified and directed by EIC.(Note: Measurement shall be measured/paid in Running metre)

M&L for providing and fixing in repair Stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. , including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasterners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangemnet and its components including levelling, grouting, providing holes as required for services etc. complete all as specified.

Dismantling wall and ceiling boards( Fibre, pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified & directed.

S&F interlocking aluminium powder coated snap grid consists of main Tee runners of size 38mm x 25mm x 1.00 mm spaced 1200mm centre to centre and cross Tee of size 25mm x 25mm x1.00mm, 1200 long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mm x 600mm and provide a secondary cross Te 25mm x 25mm x 1.4mm (of length 600mm) to be interlocked of the centre of 1200mm x 600mm panel to form a grid of 600mm x 600mm and wall angle 25mm x 25mm x 1.5mm . Aluminium alloy extruded section shall be aluminium anodized ( minimum 15 micron) and shall conform to IS 733, IS 1285 and IS 737, and providing and fixing with Hangers of 4mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long size of grid 600 x 600mm with non asbestos cement pre-painted building board 4mm thick of make E board classic of M/s Everest industries Ltd or equivalent make as approved, “in ceiling fixed with screw as per manufacturer instruction” complete all as specified and directed

S&F aluminium powder coated (min thickness 50 microns) frame for doors, windows, ventilators, complete all as specifed and directed

S & F aluminium powder coated door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. all as specified complete all as specifed and directed

S&F powder coated (min thickness 50 microns) sliding window, three track shutters with sash bars, locking rails, locking arrangements including necessay joinery cleats, glazing clips, rubber packing, chowkats aluminium snap beading, screws, suitable handle etc with and including sheet glass of 4mm thick black tinted and stainless steel wire loth 0.36mm nominal dia of wire and average width of aperature 1.40mm, size of side rails, top rails , bottom rail 30x10mm and size of three track chowkat frame 90 x 30mm and thickness of aluminium member shall be 1.40mm thick complete all as specified in MES SSR, Part-I clause 10.37 complete all as specified and as directed.

S&F aluminium powder coated (min thickness 50 microns) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F for powder coated (min thickness 50 microns) aluminium ventilator shutters with frame not less than 0.45Kg/Rm, half bottom portion fixed with 4mm thick glass with fixed type shutter and top half portion lower type with 4mm thick frosted glass and outer side fixed with stainless steel wire mesh, shutters aluminium sections weighing 0.45 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary aluminium fittings etc complete all as specified and directed.

S&F Sheet glass ordinary quality 4.00 mm thick exc 0.5 sqm each pane with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specifed and directed

S&F 4.80 mm tthick black tinted glass of any size in each pane complete all as specified and directed

S & F 2 to 2.5 mm thick aluminium composite panel sheet composed of two thin massive aluminium sheet with core of plastic polythene in doors , windows and ventilators complete all as specifed and directed

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of apreature 1.40mm and fixed in aluminium windows, wooden doors etc complete all as specified.

S&F wire netting of stainless steel wire 1.4mm dia fixed with tinned tacks of stainless steel wire staples Size of mesh in 20 mm mm with CNC cutting in glazed and skeleton WPC doors/ windows complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of apreature 1.40mm of any location & height with suitable wooden beading if required and fixing arrangements etc complete all as specified & directed

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillers etc but including ashlar facings, dressed stone work and precast concrete articles

M&L for random rubble masonry, uncoursed well bonded bedded and solidly hearted built in CM 1:6 complete all as specified and directed.

M and L for brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4) complete all as specifed and directed

M &L for Keyed pointing to random or polygonal rubble, uncoursed or brought upto course on stone masonary in CM (1:4) complete all as specifed and directed

M and L for 75mm thick PCC (1:3:6) type C-2 using 40mm grade stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and as directed.

M and L for hardcore of gauge n.exc 63mm deposited, spread in layers n.exc 15 cm thick,watered and rammed to a true surface complete all as specified and as directed.

M&L 50mm thick (average) cement concrete type B-2, 1:2:4 (20mm graded aggregate) in sub base to floor.

M&L for M-35 precast cement concrete interlocking paver blocks 60mm thick rubber moulded with grey cement and pigment conforming to IS-15658-2006 as in pavement laid over 30mm thick stone dust cushion laid dry to the profile all as per manufactuerers insturctions complete all as specified and directed by the Engineer-in-Charge

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition)

S&F in repairs bib taps standared of PTMT 15mm bore dia any colour high presure screwed for iron pipe (minimum weight 90 gms) complete all as specified and directed

S and F bib taps, cast copper alloy 15mm bore, screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. (Cat No. Cera QT F2006151 or equivalent in kohlar, grohe and Roca )

S&F in repair 15mm dia brass chromium plated two way bib cock with long flange screwed down for 15 mm dia bore GI Pipe complete all as specified and directed. Make Jaguar Cat Part No: FLR 5041 N or equivalent in kohlar, grohe and Roca .

S & F 15 mm size chromium plated swan neck type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed Make Cera Cat No F2014104 or equivalent in kohlar, grohe and Roca .

S&F in repair Maze Overhead Shower 200X200mm Square Shape Single Flow (Body & Face Plate Stainless Steel with Chrome Finish) with Rubit Cleaning System including showe arm of size 400x25x25mm sq shape for wall mounted showers with flange, fixing to steel pipe or union complete all as specified Make Jaguar (Cat part No : OHS-1619 & SHA 455L400 or equivalent in kohlar, grohe and Roca

Taking down 100/75 mm dia PVC/CI sand cast soil, waste and vent pipes, in any length with or without etc in any position

S&F PVC (SWR) pipe single socketed any length with rubber ring joints fixed to wall complete all as specified & directed bore of pipe in mm complete all as specifed and directed

S&F of PVC(SWR) bends of any radius

(a) 75 mm dia

(b) 110 mm dia

S&F of PVC(SWR) branch piece,single(single Y) 110 mm dia equal or unequal

S&F of PVC(SWR) vent cowl of 75/ 110mm bore

S and F 110mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed.

S and F 75 mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed.

S&F in repair grating doom PTMT of 100mm dia complete all as specifed and directed

S&F 75 mm dia PVC(SWR) floor trap,plain with grating including jointing with solvent cement

Supply for Pipe Supporting Clamping - Single Pipe of dia 20 mm (3/4") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 100 mm (4"): Pipe Support Clamping made of: 1. Mono Bracket for 20 mm (3/4") pipe having Wall Distance 100 mm (4") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 20 mm (3/4") pipe, Wall distance 75 mm (3") - 1 Nos. 2. U Bol Rubber Sleeve mounted for 20 mm (3/4") GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Pune Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : CEPZ/2023/TD/03 and CEPZ/2024/01. Make : Shaivi or equivalent as approved by GE.

S and F in repair vitreous china water closet squating pan Orissa pattern 580 X 440mm white with integral foot rest and P/S trap complete including lime concrete bedding complete all as specified and as directed.(Make Cera Cat No S3010110) or equivalent in kohlar, grohe and Roca .

S & F Vitreous china wash down water closet (pedestal pattern) of size 520x360x390mm , snow white including plastic water closet seat, closed pattern with flat bottom , and cover and mild steel choromium plated or aluminium hinging device complete fixed. (Make Cera Cat No. S1053101 S trap or equivalent in kohlar, grohe and Roca .

S and F in repair PVC valveless, syphonic action type, flushing cistern, low level of 10 ltr capacity, SNOW white with inlet, ball valve, float and handle including brackets the exposed surfaces of brakets shall be painted with two coats of synthetic enamel paint over one coat of primer complete all as specified and as directed. (Make Cera Cat No. B1010109)

S and F vitreous china counter type oval shape wash basin, snow white, size 560 X 470x190 mm or equivalent including cutting for and pinning in for bracket and 32mm dia CP waste coupling, 32mm dia PVC waste pipe and connection to drain pipe complete all as specified and as directed.(Cat No. Cera S2030104_13)

S&F for high density polyethylene pipes of Bore 50 mm of pressure rating 6 kgf/cm2 fixed complete to walls ,ceilings or in floors

S&F Vitreous China bowl urinal flat back, size of 315X265X440 mm white (minimum),with grating and union for discharge pipe including Flush pipe of polyethylene of high density 32 mm dia complete all as specifed and directed (Make Cera Cat No S4020104 or equivalent in kohlar, grohe and Roca .

S/F PVC connections 15mm size with PTMT nuts of length 300mm.

S&F in repair stop valve, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed

S & F in repair 15 mm size chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specifed and directed

S&F 5mm thick mirrors with fixed with stainless steel bolt & nut and fixed to brick/stone masonry walls built in cement mortor etc complete all as directed.

M&L for Cutting holes into or through stone wall, cement concrete slabs, chajjas, etc. reinforced or otherwise exc 100 Sqcm to n exc 250 sqcm including packing of hole with cement concrete

M and L for reinforced cement concrete type B1 1:2:4 (20 mm graded stone aggregates) for lintels all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs also splays between floors and beams complete all as specified and as directed.

M and L mild steel TMT bars 10mm dia and over cut to length bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (anneled) not less than 0.9mm dia or securing with clips quality coinforming to IS complete all as specified and as directed.

M and L mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirupps,spacers and binders complete all as specified and as directed.

Taking down cement plaster on brick or stone wall etc including raking out joints hacking for keys scrubbing down with water etc. all as specified and directed

M&L for rendering 15mm thick in cement mortar(1:6) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing and finishing even and smooth complete all as specifed and directed

M&L for preparating newly plastered surfaces of walls/ ceilingsand applying two coats of OBD over over a thin layer of wall care putty over a coat of alkali resistant primer coat complete all as specified and directed.

M&L rendering 15 mm thick cement mortar on stone surfaces, concrete surfaces or other than fair faces of brick work in cm 1:4 finished even and fair without using extra cement using Water Proofing Compound complete all as specifed and directed

M&L for Preparation of newly plastered surfaces of any description and applying two coats of exterior acrylic weather coat emulsion paint on walls over a coat of water based primer complete all as specified and directed

M&L for rendering 05 mm thick (1:3) on fair faces of concrete surfaces incl preparation to new surfaces on ceilings finished even and smooth without using extra cement

M&L three coat of white wash including preparation of new surfaces on ceilings

M&L for preparation of new surfaces of any description by and applying three coats of white wash on undecorated surfaces of walls complete all as specified and directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for preparation of old steel surfaces and applying one coat of synthetic enamel paint on old steel surfaces, girth or width n exc 10cm

Providing precast cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) in manhole cover slab placed complete all as specified and as directed.

M&L for complete removal of old painted surfaces of walls by washing, rubbing down,stopping and applying two coat of oil bound distemper over average 1.50mm thick wall care putty over a coat of alkali resistant primer coat prepatory to distemper on walls and ceilings

M&L for complete removal of existing wall/stone surfaces including preparation (i.e. brooming down on plastered / unplastered surfaces complete) and applying two coat of Acrylic weather proof exterior paint over water based primer(Make: APEX of Asian Paint or equivalent) complete all as specified and directed.

M&L for preparation of old painted surfaces of any description by Washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of white wash on undecorated surfaces of walls/ceilings complete all as specified and directed.

Material & Labour for painting with one coat of synthetic enamel paint on old wooden/steel surfaces exc 10cm width or girth including preparation of old wooden surfaces all as specified and directed by EIC.

Taking down carefully copper/aluminium point wiring complete (light,fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting regulator, sockets main switches, DB removing materials to store and making good to disturb surfaces of wall/floors etc as specified & directed.

Point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLS type drawn through and including PVC casing and caping (ISI marked) of adequate size and its accessories with PVC boxes of adequate size, with modular cover plate with frame of adequate required modules for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLS type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metalic bodies of luminaires/ fan at other end complete all as specified and directed for the following:-

(a) One light point and one fan point controlled by one, one way swtich.

(b) One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified.

(c) All as per ser item No. 142 .02 here in before but on independent board.

(d) All as per ser item No. 142.01 here in before but one light point controlled by 2 way switches.

(e) All as per ser item No. 142.01 here in before but one bell/buzzer point controlled by one push button on the same board with other switches or independent.

(f) All as per ser item No. 142 herein before but with 2.5 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 6 pin socket outlet point including PVC cable 2.5 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to commen earth & earth terminals including Fibre insulation boards, treated on one face only of adequate size for mounting purposes.

Taking down carefully ceiling/ exhaust fan, sealing cable end dismantling blades and removing fan and blades to store for safe custody for re-fixing after completion of B/R nature work.

M&L for painting of ceiling fan and exhaust fan complete in site with synthetic enamel paint by spray painting including filling cavities with filter , one coat after cleaning of dust etc

Hanging only ceiling fan and connecting up including connecting of cable from ceiling rose to ceiling fan.

Fixing only exhaust fan and connecting up including connecting of cable from ceiling rose to exhaust fan.

Supply and fixing of switch modular type 6 Amps one way, 1 module, AC 230 Volts, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing of modular type socket 6 Amps 3 pin round socket with child safety shutter (ISI marke), AC 230 Volts, shrouded terminals, smooth plug removal and insertion complete all as specified and directed.

Supply and fixing of switch modular type 16 Amps one way, 1 module, AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing of modular type socket 6 Amps/ 16 Amp 3 pin socket with child safety shutter (ISI marke), AC 230 Volts, shrouded terminals, smooth plug removal and insertion complete all as specified and directed.

Supply and fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings with invertor LED bulb 9 watt complete all as specified and directed.

Supply and fixnt ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish. Make - Havells /Anchor / Legrand.

Supply and fixing of switch modular type bell push 6 Amps 1 module, AC 230 Volts, LED based indicator, laser marking, ISI marked complete all as specified and directed.

Supply and fixing of switch modular type 6 Amps two way, 1 module, AC 230 Volts, , ISI marked complete all as specified and directed.

Supply and fixing of modular type fan 8 step regulator, 100 watt, AC 230 Volts, 2 module, laser marking complete all as specified and directed.

Supply and fixing of LED 20 Watt inverter LED batten with rod complete with lithium ion battery with charging time 8-10 hours and backup time upto 4 hours mounted on clamp of suitable size connecting up with three core flexible copper conductor cable of suitable size from ceiling rose.

Supply and fixing of LED 10 Watt inverter LED batten with rod complete with lithium ion battery with charging time 8-10 hours and backup time upto 4 hours mounted on square box of suitable size connecting up with three core flexible copper conductor cable of suitable size from ceiling rose.

Supply and fixing of bell, AC, 230 volts, single phase complete all as specified and directed. Make -Legrand/ Havells/ Anchor.

Supply and fixing of sheet metal enclosures with plug socket single pole and neutral with two pin and earth plug and with one MCB of 20 Amps (SP) complete all as specified. Make- L&T/ ABB/ Legrand/ Schenider.

Supply and fixing of sheet metal enclosures with plug socket triple pole and earth enclosure with three pin and earth plug with socket, 415 volts complete with one MCB of 32 Amps (TP) complete all as specified. Make- L&T/ ABB/ Legrand/ Schenider.

Supply and fixing in replacement of submain wiring with four single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 10 Sqmm drawn through in and including PVC heavy duty surface casing caping including 10 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i) Four runs of cables and one run of continuous earting cable drawn in casing and caping will be measured as one length of sub main. (ii) PVC casing caping and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for sinking for boxes and making good to wall, floors etc.

Supply and fixing in replacement of submain wiring with four single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 6 Sqmm drawn through in and including PVC heavy duty surface casing caping including 6 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i) Four runs of cables and one run of continuous earting cable drawn in casing and caping will be measured as one length of sub main. (ii) PVC casing caping and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for sinking for boxes and making good to wall, floors etc.

Supply and fixing in replacement of submain wirng with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 4 Sqmm drawn through in and including PVC heavy duty surface casing caping including 4 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed.

Supply and fixing in replacement of submain wirng with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 2.5 Sqmm drawn through in and including PVC heavy duty surface casing caping including 2.5 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note for Srl item No 23 to 24 herein before :- (i) Two runs of cables and one run of continuous earting cable drawn in casing and caping will be measured as one length of sub main. (ii) PVC casing caping and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for sinking for boxes and making good to wall, floors etc.

Supply and fixing in replacement sheet metal enclosure (factory made), TPN Vertical Distribution Boards (MCCB Incomer) IP43 protection Double Door : Plain 4 way with 200 Amps rated busbar all as specified and directed.

Supply and fixing in replacement sheet metal enclosure (factory made), TPN Vertical Distribution Boards (MCCB Incomer) IP43 protection Double Door : Plain 8 way with 200 Amps rated busbar all as specified and directed.

Supply and fixing in replacement distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 415 volts, 200 Amp rated bus bar with front openable cover suitable for TP & N 4 ways all as specified & directed.

Supply and fixing in replacement distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 8 ways all as specified & directed.

Supply and fixing in replacement 3 Pole MCCB 125 Amp, 50 Hz, 415 V, with adjustable thermal & adjustable magnetic setting, breaking capacity 25 KA.

Supply and fixing in replacement MCCB 63 Amp TP, 415 volts 16KA. Make - Hager CP No HDA063U or Schnider/ Legrand.

Supply and fixing in replacement MCB FP 63 Amp, 415 Volts, 50 Hz with 10 KA.

Supply and fixing in replacement of MCB DP/SPN 6-32 Amps, 230 Volts, 50 Hz with 10 KA.

Supply and fixing in replacement of MCB SP 6-32 Amps, 230 Volts, 50 Hz with 10 KA.

Material & Labour in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion.

Supply and fixing in replacement of 35 Watt LED street light fitting luminaire, energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with bracket of adequate size complte IP66 protection and impact resistance of IK08.E68, including coneecting up with 2/3 core flexible coppper conductor cable , compete all as specified and directed by Engr-in-Charge.

Supply and fixinf in replacement of LED luminaire 600 x 600mm, 36 watt, 220 volts AC recessed/ surface type fittings, IP 20 with epoxy powder coated CRCA sheet housing with electronic driver, connector block, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Supply and fixing in replacement of LED bulkhead 10 watt 220 volts AC with high efficacy PMMA diffuser soft glare free light complete with drivers, clamps complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

sapana enterprises (BID ID -3341604)

AGRAWAL ASSOCIATES (BID ID -3343266)

M/S MANISH CONSTRUCTION CO (BID ID -3342823)

Samruddhi Construction (BID ID -3340011)

MS. G.A. CONSTRUCTION (BID ID -3342754)

SHREE KRISHNA INFRASTRUCTURE (BID ID -3340988)

M/S K.K.BINNAR (BID ID -3342755)

MUKESH CONSTRUCTION CO (BID ID -3343230)