Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹22.0 L
EMD Value
₹43,910
Closing Date
31 Jul 2024, 5:30 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Sukhoi Engine Division, Koraput
Sukhoi Engine Division, Koraput
PAINTING OF TEST HOUSE BUILDINGS AND UTILITY BUILDINGS OF SU-30 FACTORY.
6845
e TN NO W-01/24-25
Works
Mig Complex- Sukhoi Eng Divn-Koraput-Civil
₹0
₹43,910
31 Jul 2024
6 Apr 2024
6 Apr 2024
31 Jul 2024
Labour charges for removal, lowering the sheets from the roof and depositing them to salvage store or department store. All safety precaution shall be taken by the contractor during execution & contractor shall be responsible for safety / tradesman engaged by him etc. all complete as per specification and direction of Engineer-in-charge.
Labour charges for dismantling of concrete in ground floor and pavings of any description and in any position not otherwise specifically provided for with out causing any damage to the surrounding & disposal of the dismantled debries etc. all complete as per specification and direction of Engineer-in-charge.
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m etc all complete as per specification & direction of EIC.
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete all complete as per specification & direction of EIC.
Supplying, carrying to site all approved materials, providing and laying required thickness of controlled plain cement concrete of 1:4:8 using 40 mm and down size coarse graded hard stone aggregate for leveling course in trenches, pits and foundation, mass concrete and other similar works at all levels and heights elevations including mechanical mixing, transporting and placing at all lifts, vibrating compacting all materials, labour leads and lifts, tools and plant, machineries etc all complete as per specification & direction of EIC.
Supplying, carrying to site all approved materials, providing and laying RCC (1:1.5:3) using 20mm and down hard granite graded stone aggregates for foundation, footing, walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves including, mixing, placing of concrete consolidation, mechanical vibration, curing, neatly finishing all exposed surfaces of RCC works etc all complete as per specification & direction of EIC.
Supplying carrying to site all approved materials and placing in all positions steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete etc. all complete as per direction of Engineer in charge.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. etc all complete as per specification & direction of EIC.
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, mass concrete work etc all complete as per specification & direction of EIC.
Supplying, carrying to site all approved materials and providing structural steel including fabricating, hoisting and erecting in position Comprising of Fe-410 (Grade-250) at all elevations, levels and heights including joist, channel, angle or tee sections, fixed independently with a coat zinc chromate / red oxide primer etc (cut to ordinary lengths as indicated) etc all complete as per specification & direction of EIC.
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc all complete as per specification & direction of EIC.
Providing and fixing precoated galvanised steel sheet roofing accessories (CRIMP CURVE) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete etc all complete as per specification & direction of EIC.
Supplying, carrying to site all approved materials, providing and painting with Two coats of High gloss Synthetic Enamel Paint (Class – 1 / Grade – 1) confirming to latest edition of IS 2932 of approved make Steel surfaces at all heights neatly without brush mark. The work shall include preparation of the surfaces by using sand/ emery papers, cleaning, removal of the scales, peeled surfaces, filling the pits/ depressions, nail – holes, knots etc. by putty and applying paint by using brush/ spray to get uniform finish without any patches including erection of safe/ rigid scaffoldings, cleaning the area after painting etc all complete as per specification & direction of EIC.
Supplying, carrying to site all approved materials, providing and painting with Two or more coats of High gloss Synthetic Enamel Paint (Class – 1 / Grade – 1) confirming to latest edition of IS 2932 of approved make over an under coat of suitable shed on concrete surfaces at all heights neatly without brush mark. The work shall include preparation of the surfaces by using sand/ emery papers, cleaning, removal of the scales, peeled surfaces, filling the pits/ depressions, nail – holes, knots etc. by putty and applying paint by using brush/ spray to get uniform finish without any patches including erection of safe/ rigid scaffoldings, cleaning the area after painting etc all complete as per specification & direction of EIC.
Total
I / We hereby quote percentage above (+) or below (-) the Estimated cost
Sub Total Works Amount
ADD GST @ 18% (( IGST18%) or (CGST @ 9% +SGST@ 9%)), Whichever is applicable
GRAND TOTAL
Note : (i) : It is a percentage rate tender. Hence the tenderers are required to quote rates on percentage basis i.e. above or below the estimated cost put to tender. (ii) The quoted rates in the bill of quantities are inclusive of all types of taxes, duties levies, fees and charges etc., imposed by Central/ State Govt. and local bodies Compensation Cess, Labour Cess, Custom Duty, royalties and other levies. It shall also include all other costs including loading, un-loading, insurance, transportation, testing and Certification expenses except GST . GST at the prevailing percentage is added in the BOQ at the end.
GOODS AND SERVICE TAX (GST)
Bidder should indicate GSTIN No. (Copy of GST registration to be enclosed) and PAN No. (copy of PAN to be enclosed).
Tender will be considered/ accepted, if & only if the vendor has a valid GST Registration No
Central Tax/ State Tax/ Integrated Tax/ Union Territory tax to be quoted as per GST Law
Bidders to ensure correct applicability of Central Tax/ State Tax/ Integrated Tax/ Union Territory tax based on the Inter / Intra state movement Supply of goods and provision services or both
Bidder shall mention the SAC Code/HSN Code for goods and services in accordance with GST law in their Bid and subsequently in their tax invoice. HAL, Koraput Division shall not be responsible for any error in SAC Code/HSN Code for goods and/or services specified by supplier/contractor
The Tax Invoice for supply of Goods & Services should be raised as per the provision of GST Act & Rules and must compulsorily mention the following
a. HAL, Korpaut Division GST registration number as 21AAACH3641R1ZJ
b. Name & address of supplier / Vendor/ Contractors
c. GSTIN of Supplier / vendors / Contractors
d. Consecutive Serial Number & date of issue
e. Description of goods or services
f. Total value of supply
g. Taxable value of supply
h. Tax Rate – Central Tax & State Tax or Integrated Tax, Cess
i. Amount of Tax charged
j. Place of supply
k. Address of delivery if different from place of supply
l. Signature of authorized signatory
Reimbursement of GST to the vendor is contingent upon complying with the following condition by the service provider
i. Uploading the (invoices raised on HAL, KoraputDivision ) onward GST Return (GSTR-1) in GSTN Network portal within the statutory time period
ii. Discharging the GST tax liability to the Government.
iii. Submission of Tax Invoice to HAL, Korpaut Division.
iv. Submission of proof of payment of GST to HAL, Korpaut Division.
v. Receipt of goods / services by HAL Koraput Division.
vi. Availment of Input Tax Credit by HAL, Korpaut Division .
In case GST credit is delayed/ denied to HAL, Korpaut Division, due to non/delayed receipt of goods and/or services and/or tax invoice or expiry of timeline prescribed in GST Law for availing such ITC, or any other reason not attributable to HAL, Korpaut Division, GST amount shall be recoverable from Vendor along with interest & penalty levied/ leviable on HAL, Korpaut Division, as the case may be
In case vendor delays declaring such invoice in his return and GST credit availed by HAL, Korpaut Division is denied or reversed subsequently as per GST law, GST amount paid by HAL, Korpaut Division towards such ITC reversal as per GST law shall be recoverable from vendor/contractor along with interest & penalty levied/ leviable on HAL, Korpaut Division.
In case of discrepancy in the data uploaded by supplier in the GSTN portal or in case of any incomplete work/service, then HAL, Korpaut Division will not be able to avail the tax credit and will notify the supplier of the same. Supplier has to rectify the data discrepancy in the GSTN portal or issue credit note (details to be uploaded in GSTN portal).
For any such delay in availing of tax credit for reasons attributable to vendor (as mentioned above), interest as per the GST Act & Rules, along with penalty, if any will be deducted for the delayed period i.e. from the month of receipt till the month tax credit is availed, from the running bills.
Penalty amount so determined along with GST if applicable thereon shall be recovered from the contractor.
Any reduction in rate of Tax on any supply of goods or services or the benefit of input tax credit shall be passed on to the recipient by way of commensurate reduction in prices. Bidders have to submit declaration in their bid that they have complied with ‘Anti-profiteering clause’ under GST law.
The bidder’s quoted rates/ price should be after considering the Input Credit under GST law at their end, since GST on output (GST amount charged in Invoice) will be paid by HAL.
In case any changes in taxes and duties as per Gov. Notification (including GST), the same shall be applicable from time to time.
Quarters will be allotted to the awarded agency subject to availability & recommendation from the E-I-C/ O-I-C for which rents as applicable will be recovered from the running bills of the agency.
SCHEDULE-A
HINDUSTAN AERONAUTICS LIMITED
KORAPUT DIVISION
CENTRAL CONTRACT CELL
COMMERCIAL BID
BILL OF QUANTITIES FOR THE WORK OF "PROVISION OF SHED AT TEST HOUSE IN SED"
LINE NO : KPTCC/W/382
NAME OF THE AGENCY :
Demolishing cement concrete manually/by mechnical means including disposal of material within 50M lead as per direction EIC. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) complete as per directions of Engineer-in-charge
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all complete as per directions of Engineer-in-charge
Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge
Filling avaliable excavated (excluding rock) in treanch, plinth, sides of foundations etc.in layers not exceeding 20cm in depth.consolidating each deposited layer by ramming & watering,lead up to 50m & for all lift.complete as per direction of EIC.
Supplying and filling in plinth with sand under floors,including watering,ramming,consolidating & dressing complete as per direction of EIC.
Supplying carrying to site all approved materials, providing and laying in position cement concrete 1:4:8 ( 1 cement : 4 course sand (zone-III )derived from natural sources : 8 graded stone aggregate 40mm nominal size derived from natural sources ) etc excluding the cost of centering and shuttering - All work up to plinth level . all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials, providing and laying in position reinforced cement concrete 1:1.5:3 (1 cement : 1.5 course sand ( Zone -III ) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources ) etc excluding the cost of centering and shuttering - All work up to plinth level . all complete as per direction of Engineer in charge.
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete all complete as per direction of Engineer in charge.
Supplying carrying to site all approved materials and placing in all positions steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete etc. all complete as per direction of Engineer in charge.
Supplying, carrying to site all approved materials and plastering with 15 mm thick cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement: 4 coarse sand) etc. all complete as per direction of Engineer in charge.
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. etc. all complete as per direction of Engineer in charge.
Supplying and providing Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. all complete as per direction of Engineer in charge.
Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture etc. all complete as per direction of Engineer in charge.
Total
I / We hereby quote percentage above (+) or below (-) the Estimated cost
Sub Total Works Amount
ADD GST @ 18% (( IGST18%) or (CGST @ 9% +SGST@ 9%)), Whichever is applicable
GRAND TOTAL
Note : (i) : It is a percentage rate tender. Hence the tenderers are required to quote rates on percentage basis i.e. above or below the estimated cost put to tender. (ii) The quoted rates in the bill of quantities are inclusive of all types of taxes, duties levies, fees and charges etc., imposed by Central/ State Govt. and local bodies Compensation Cess, Labour Cess, Custom Duty, royalties and other levies. It shall also include all other costs including loading, un-loading, insurance, transportation, testing and Certification expenses except GST . GST at the prevailing percentage is added in the BOQ at the end.
GOODS AND SERVICE TAX (GST)
Bidder should indicate GSTIN No. (Copy of GST registration to be enclosed) and PAN No. (copy of PAN to be enclosed).
Tender will be considered/ accepted, if & only if the vendor has a valid GST Registration No
Central Tax/ State Tax/ Integrated Tax/ Union Territory tax to be quoted as per GST Law
Bidders to ensure correct applicability of Central Tax/ State Tax/ Integrated Tax/ Union Territory tax based on the Inter / Intra state movement Supply of goods and provision services or both
Bidder shall mention the SAC Code/HSN Code for goods and services in accordance with GST law in their Bid and subsequently in their tax invoice. HAL, Koraput Division shall not be responsible for any error in SAC Code/HSN Code for goods and/or services specified by supplier/contractor
The Tax Invoice for supply of Goods & Services should be raised as per the provision of GST Act & Rules and must compulsorily mention the following
a. HAL, Korpaut Division GST registration number as 21AAACH3641R1ZJ
b. Name & address of supplier / Vendor/ Contractors
c. GSTIN of Supplier / vendors / Contractors
d. Consecutive Serial Number & date of issue
e. Description of goods or services
f. Total value of supply
g. Taxable value of supply
h. Tax Rate – Central Tax & State Tax or Integrated Tax, Cess
i. Amount of Tax charged
j. Place of supply
k. Address of delivery if different from place of supply
l. Signature of authorized signatory
Reimbursement of GST to the vendor is contingent upon complying with the following condition by the service provider
i. Uploading the (invoices raised on HAL, KoraputDivision ) onward GST Return (GSTR-1) in GSTN Network portal within the statutory time period
ii. Discharging the GST tax liability to the Government.
iii. Submission of Tax Invoice to HAL, Korpaut Division.
iv. Submission of proof of payment of GST to HAL, Korpaut Division.
v. Receipt of goods / services by HAL Koraput Division.
vi. Availment of Input Tax Credit by HAL, Korpaut Division .
In case GST credit is delayed/ denied to HAL, Korpaut Division, due to non/delayed receipt of goods and/or services and/or tax invoice or expiry of timeline prescribed in GST Law for availing such ITC, or any other reason not attributable to HAL, Korpaut Division, GST amount shall be recoverable from Vendor along with interest & penalty levied/ leviable on HAL, Korpaut Division, as the case may be
In case vendor delays declaring such invoice in his return and GST credit availed by HAL, Korpaut Division is denied or reversed subsequently as per GST law, GST amount paid by HAL, Korpaut Division towards such ITC reversal as per GST law shall be recoverable from vendor/contractor along with interest & penalty levied/ leviable on HAL, Korpaut Division.
In case of discrepancy in the data uploaded by supplier in the GSTN portal or in case of any incomplete work/service, then HAL, Korpaut Division will not be able to avail the tax credit and will notify the supplier of the same. Supplier has to rectify the data discrepancy in the GSTN portal or issue credit note (details to be uploaded in GSTN portal).
For any such delay in availing of tax credit for reasons attributable to vendor (as mentioned above), interest as per the GST Act & Rules, along with penalty, if any will be deducted for the delayed period i.e. from the month of receipt till the month tax credit is availed, from the running bills.
Penalty amount so determined along with GST if applicable thereon shall be recovered from the contractor.
Any reduction in rate of Tax on any supply of goods or services or the benefit of input tax credit shall be passed on to the recipient by way of commensurate reduction in prices. Bidders have to submit declaration in their bid that they have complied with ‘Anti-profiteering clause’ under GST law.
The bidder’s quoted rates/ price should be after considering the Input Credit under GST law at their end, since GST on output (GST amount charged in Invoice) will be paid by HAL.
In case any changes in taxes and duties as per Gov. Notification (including GST), the same shall be applicable from time to time.
Quarters will be allotted to the awarded agency subject to availability & recommendation from the E-I-C/ O-I-C for which rents as applicable will be recovered from the running bills of the agency.
SCHEDULE-A
HINDUSTAN AERONAUTICS LIMITED
KORAPUT DIVISION
CENTRAL CONTRACT CELL
COMMERCIAL BID
BILL OF QUANTITIES FOR THE WORK OF "PAINTING OF TEST HOUSE BUILDINGS AND UTILITY BUILDINGS OF SU-30 FACTORY"
LINE NO : KPTCC/W/374-1
NAME OF THE AGENCY :
Supplying carrying to site all approved materials and painting ,finishing walls with Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/ 10 sqm) on plaster surface in all heights. The paint should provide good /enhanced dirt,fungal and wheather resistance to exterior works. The work shall include the preparation of wall surface by using sand paper, wire brush, removal of scales and peeled surface, filling the pits / depression, nail-holes by putty and painting uniformly without any patches and brush marks including erection of safe scaffolding, cleaning, washing the areas after painting etc. all complete as per specifications and directions of Engineer in charge.
Supplying, carrying to site all approved materials and providing and painting with Two or more coats of High gloss synthetic Enamel paint (class-1/ Grade-1) confirming to latest edition of IS of approved make/shade on Steel surface at all heights neatly without brush mark. The work shall include preparation of the surfaces by using sand/ emery papaers, cleaning , removal of the scales, peeled surfaces , filling the pits/ depressions, nail holes, knots etc. by putty and applying paint by using brush/ spray to get uniform finish without any patches including erection of safe/ rigid scafoldings, cleaning the area after painting etc. All complete as per specification and direction of Engineer-in Charge.
Supplying,carrying to site all approved material and applying two or more coat of white washing on wall or ceiling surface at all hights. The work includes prparation of surface i,e all loose particles and scales shall be scrapped off and holes in plaster as well as patches of less than 50 cm area shall be filled up with mortar of the same mix. The lime wash shall be prepared from fresh stone white lime (Narnaul or Dehradun quality). The lime shall be thoroughly slaked on the spot, mixed and stirred with sufficient water to make a thin cream. This shall be allowed to stand for a period of 24 hours and then shall be screened through a clean coarse cloth. 40 gm of gum dissolved in hot water, shall be added to each 10 cubic dicimetre of the cream. The approximate quantity of water to be added in making the cream will be 5 litres of water to one kg of lime. Indigo (Neel) upto 3 gm per kg of lime dissolved in water, shall then be added and stirred well. Water shall then be added at the rate of about 5 litres per kg. of lime to produce a milky solution.The work also includes cleaning / washing areas after white washing etc. all complete as per specifications and directions of Engineer-in-charge.
Supplying , carrying to site all approved materials and applying 2 coats of Wall painting with acrylic emulsion paint having VOC (Volatile Organic Compound ) content less than 50grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade at all heights using approved quality mix. The work shall include the preparation of wall surface by using sand paper, wire brush, removal of scales and peeled surface, filling the pits / depression, nail-holes by putty and painting uniformly without any patches and brush marks including erection of safe scaffolding, cleaning, washing the areas after painting etc. all complete as per specifications and directions of Engineer in charge.
Supplying, carrying to site all approved materials and providing and painting with Two or more coats of High gloss synthetic Enamel paint (class-1/ Grade-1) confirming to latest edition of IS of approved make/shade on wall surface at all heights neatly without brush mark. The work shall include preparation of the surfaces by using sand/ emery papaers, cleaning , removal of the scales, peeled surfaces , filling the pits/ depressions, nail holes, knots etc. by putty and applying paint by using brush/ spray to get uniform finish without any patches including erection of safe/ rigid scafoldings, cleaning the area after painting etc. All complete as per specification and direction of Engineer-in Charge.
Repairs to plaster With cement mortar 1:4 (1 cement : 4 fine sand) of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters . and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.
Supplying carrying to site all approved materials and applying priming coat With water thinnable cement primer on wall surface having VOC content less than 50 grams/ litre on plaster surface in all heights. including surface preparation.etc all complete as per specification and direction of EIC.
Supplying carrying to site all approved materials and applying with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works in all heights. including surface preparation.etc all complete as per specification and direction of EIC.
Total
I / We hereby quote percentage above (+) or below (-) the Estimated cost
Sub Total Works Amount
ADD GST @ 18% (( IGST18%) or (CGST @ 9% +SGST@ 9%)), Whichever is applicable
GRAND TOTAL
Note : (i) : It is a percentage rate tender. Hence the tenderers are required to quote rates on percentage basis i.e. above or below the estimated cost put to tender. (ii) The quoted rates in the bill of quantities are inclusive of all types of taxes, duties levies, fees and charges etc., imposed by Central/ State Govt. and local bodies Compensation Cess, Labour Cess, Custom Duty, royalties and other levies. It shall also include all other costs including loading, un-loading, insurance, transportation, testing and Certification expenses except GST . GST at the prevailing percentage is added in the BOQ at the end.
GOODS AND SERVICE TAX (GST)
Bidder should indicate GSTIN No. (Copy of GST registration to be enclosed) and PAN No. (copy of PAN to be enclosed).
Tender will be considered/ accepted, if & only if the vendor has a valid GST Registration No
Central Tax/ State Tax/ Integrated Tax/ Union Territory tax to be quoted as per GST Law
Bidders to ensure correct applicability of Central Tax/ State Tax/ Integrated Tax/ Union Territory tax based on the Inter / Intra state movement Supply of goods and provision services or both
Bidder shall mention the SAC Code/HSN Code for goods and services in accordance with GST law in their Bid and subsequently in their tax invoice. HAL, Koraput Division shall not be responsible for any error in SAC Code/HSN Code for goods and/or services specified by supplier/contractor
The Tax Invoice for supply of Goods & Services should be raised as per the provision of GST Act & Rules and must compulsorily mention the following
a. HAL, Korpaut Division GST registration number as 21AAACH3641R1ZJ
b. Name & address of supplier / Vendor/ Contractors
c. GSTIN of Supplier / vendors / Contractors
d. Consecutive Serial Number & date of issue
e. Description of goods or services
f. Total value of supply
g. Taxable value of supply
h. Tax Rate – Central Tax & State Tax or Integrated Tax, Cess
i. Amount of Tax charged
j. Place of supply
k. Address of delivery if different from place of supply
l. Signature of authorized signatory
Reimbursement of GST to the vendor is contingent upon complying with the following condition by the service provider
i. Uploading the (invoices raised on HAL, KoraputDivision ) onward GST Return (GSTR-1) in GSTN Network portal within the statutory time period
ii. Discharging the GST tax liability to the Government.
iii. Submission of Tax Invoice to HAL, Korpaut Division.
iv. Submission of proof of payment of GST to HAL, Korpaut Division.
v. Receipt of goods / services by HAL Koraput Division.
vi. Availment of Input Tax Credit by HAL, Korpaut Division .
In case GST credit is delayed/ denied to HAL, Korpaut Division, due to non/delayed receipt of goods and/or services and/or tax invoice or expiry of timeline prescribed in GST Law for availing such ITC, or any other reason not attributable to HAL, Korpaut Division, GST amount shall be recoverable from Vendor along with interest & penalty levied/ leviable on HAL, Korpaut Division, as the case may be
In case vendor delays declaring such invoice in his return and GST credit availed by HAL, Korpaut Division is denied or reversed subsequently as per GST law, GST amount paid by HAL, Korpaut Division towards such ITC reversal as per GST law shall be recoverable from vendor/contractor along with interest & penalty levied/ leviable on HAL, Korpaut Division.
In case of discrepancy in the data uploaded by supplier in the GSTN portal or in case of any incomplete work/service, then HAL, Korpaut Division will not be able to avail the tax credit and will notify the supplier of the same. Supplier has to rectify the data discrepancy in the GSTN portal or issue credit note (details to be uploaded in GSTN portal).
For any such delay in availing of tax credit for reasons attributable to vendor (as mentioned above), interest as per the GST Act & Rules, along with penalty, if any will be deducted for the delayed period i.e. from the month of receipt till the month tax credit is availed, from the running bills.
Penalty amount so determined along with GST if applicable thereon shall be recovered from the contractor.
Any reduction in rate of Tax on any supply of goods or services or the benefit of input tax credit shall be passed on to the recipient by way of commensurate reduction in prices. Bidders have to submit declaration in their bid that they have complied with ‘Anti-profiteering clause’ under GST law.
The bidder’s quoted rates/ price should be after considering the Input Credit under GST law at their end, since GST on output (GST amount charged in Invoice) will be paid by HAL.
In case any changes in taxes and duties as per Gov. Notification (including GST), the same shall be applicable from time to time.
Quarters will be allotted to the awarded agency subject to availability & recommendation from the E-I-C/ O-I-C for which rents as applicable will be recovered from the running bills of the agency.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
raw.json
RAW_JSON
NIT01.pdf
TENDER_DOCUMENT • 1.56 MB
NEWGCC.pdf
TENDER_DOCUMENT • 2.92 MB
AM.pdf
TENDER_DOCUMENT • 5.21 MB
381PBO.xlsm
TENDER_DOCUMENT • 0.03 MB
PERCENTAGEBOQ.pdf
TENDER_DOCUMENT • 0.22 MB
EPS.pdf
TENDER_DOCUMENT • 0.02 MB
EPS_2.pdf
TENDER_DOCUMENT • 0.02 MB
EPS_3.pdf
TENDER_DOCUMENT • 0.02 MB
UNDERTAKING-SED.pdf
TENDER_DOCUMENT • 0.04 MB
UNDERTAKING-SED_2.pdf
TENDER_DOCUMENT • 0.04 MB
UNDERTAKING-SED_3.pdf
TENDER_DOCUMENT • 0.04 MB
382PBO.xlsm
TENDER_DOCUMENT • 0.03 MB
PBO.xlsm
TENDER_DOCUMENT • 0.03 MB
UPBOQ381.pdf
TENDER_DOCUMENT • 0.23 MB
PERCENTAGEBOQ3741.pdf
TENDER_DOCUMENT • 0.23 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .