Development of Agritourism Centre near Gate No. 4 of CCS HAU, Hisar (including Public health and EI works)

Amount

Civil work 1 to 236:- Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. (HSR 4.1)

FeUing trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 30 cm girth up to and including 60 cm girth (HSR 4.3.1)

FeUing trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 60 cm girth up to and including 120 cm girth (HSR 4.3.2)

FeUing trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 120 cm girth up to and including 240 cm girth (HSR 4.3.3)

FeUing trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Above 240 cm girth (HSR 4.3.4)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Square meter on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. All kinds of soil (HSR 4.12.1)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 Square meter on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. (HSR 4.14.1)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc, not exceeding 80 metre (HSR 4.16.1.1)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc. exceeding 80 mm metre (HSR 4.16.1.2)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. (HSR 4.32)

Providing and injecting chemical emulsion for PRE-CONSTRUCTIONAL anti termite treatment and creating a chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filing junction of wall and floor, along with the external perimetre of building, expansion joints surrounding of pipes and conduit etc, complete (plinth area of the building at ground floor only shall be measured) using Chlorpyriphos/ Lindane emulsifiable concentrate of 20% (HSR 4.39)

Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of: T' or 'L' iron or pipe (HSR 5.36.1)

Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead. (HSR 5.37)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded Cubic meter stone aggregate 20 mm nominal size) (HSR 6.1.2)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:3:6 (1 Cement : 3 coarse sand (zone-Ill) : 6 graded Cubic meter stone aggregate 20 mm nominal size (HSR 6.1.4)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded Cubic meter stone aggregate 40 mm nominal size) (HSR 6.1.6)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size). (HSR 6.1.8)

Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) 40mm thick (HSR 6.8.2)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1. 7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. (HSR 6.10)

Making plinth protection 50mm thick of cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. (HSR 6.13)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: (HSR 6.14.1) 1 : 1. 5: 3 ( 1 cement : 1. 5 coarse sand (zone-Ill): 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: (HSR 6.14.2) 1 :2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size) (HSR 6.15.1)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.16)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete (HSR 6.30.1)

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and cantilevers (HSR 6.30.3)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers (HSR 6.30.5)

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts (HSR 6.30.6)

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases (HSR 6.30.7)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.complete in all respect above plinth level. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D or more (HSR 6.34.6)

Brick work with common burnt clay modular bricks of class designation 10.5 in foundation and plinth in Cement mortar 1:4 (1 cement: 4 coarse sand) (HSR 7.20.1)

Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) (HSR 7.21.1)

Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR 7.21.2)

Brick work with common burnt clay non-modular bricks of class designation 10 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR 7.22.2)

Half brick masonry with common burnt clay non-modular bricks of class designation 10.5 in foundations and plinth in: Cement mortar 1:3 (1 cement: 3 coarse sand) (HSR 7.27.1)

Half brick masonry with common burnt clay non-modular bricks of class designation 10 .5 in superstructure above plinth level up to floor IV level. Cement mortar 1 :4 ( 1 cement :4 coarse sand) (HSR 7 .28.2)

Brick work with common burnt clay machine moulded nonmodular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1 :6 (1 cement : 6 coarse sand). Above plinth level up to floor IV level (HSR 7.40.2)

Brick work with non modular fly ash bricks conforming to IS :12894, class designation 10 average compressive strength in super structure above plinth level up to floor IV level in Cement mortar 1:6 (1 cement: 6 Coarse sand) (HSR 7.47.2)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platfonns, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shade Area of slab over 0.50 Square meter (HSR 8.26.2.2)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work (HSR 8.27.2)

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per Cubic meter of earth and gobri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1: 3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay non-modular brick tile of class designation 10 (HSR 9.11.1)

Providing gola 75x75 mm in cement concrete 1: 2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase (HSR 9.17.1)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (HSR 9.18)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/Square meter (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing periMeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and30 mm long, the periMeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and periMeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of periMeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charae but excludina the cost of painting with 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I (HSR 9.46.5)

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diaMeter (HSR 9.57.2)

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382,leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend (HSR 9.58.5.2)

Re-compacting excavated soil in plinth under floors, including watering, ramming, consolidating and dressing complete (HSR 10.1.1)

Providing and laying of conglomerate floor 50mm thick cement concrete topping 1 :2:4 (HSR 10.7)

Providing and laying of 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1: 2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1 :2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. (HSR 10.12)

Providing and laying of precast terrazzo tiles 20 to 22 mm thick with graded marble chips of size up to 12 mm, laid in floors, and landings, jointed with neat cement sluny mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement:4 coarse sand) : Light shade pigment using white cement (HSR 10.26.1)

Providing and laying of precast terrazzo tiles 20 to 22 mm thick with graded marble chips of sizes up to 12 mm, in skirting and risers of steps not exceeding 30 cm in height, on 12 mm thick cement plaster 1 :3 (1 cement : 3 coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of: Light shade pigment using white cement (HSR 10.28.1)

Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand) : 25 mm thick (HSR10.37.1 )

Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (HSR 10.38)

Providing and fixing of 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1 :5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1 :2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. Red sand stone (HSR 10.41.1)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Square meter Cat Eye or equivalent. (HSR 10.50.1 )

Providing and fixing granite stone in all shades 15mm to 18 mm thick in Square meter skirting /dado/worktop/risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1 :3 and jointed with white cement slurry mixed with pigment to match the shade of Granite including labour for fixing cramps pins and dowels etc. (HSR 10.51)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ Square meter including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (HSR 10.63.2)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ Square meter including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm (HSR 10.67.2)

Providing and laying 50mm thick factory made cement concrete inter1ocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658:2006) and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. (HSR 10.75)

Providing and laying 60mm thick factory made cement concrete inter1ocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658:2006) and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. (HSR 10.76)

Cement Concrete 1 :8:16 Flooring Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth. (HSR 10.100.2)

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. (HSR 10.107)

6 mm cement plaster of mix 1 :3 (1 cement : 3 fine sand) (HSR 11.1.1)

10 mm thick cement plaster 1 :3 (1 cement: 3 fine sand) (HSR 11.4.2)

12 mm cement plaster of mix : 1 :3 (1 cement: 3 fine sand) (HSR 11.5.2)

12 mm cement plaster of mix : 1 :4 (1 cement: 4 fine sand) (HSR 11.5.3)

12 mm cement plaster of mix : 1 :6 (1 cement: 6 fine sand) (HSR 11.5.4)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1 :6 (1 cement: 6 fine sand) (HSR 11.6.2)

12 mm cement plaster finished with a floating coat of neat cement of mix : 1 :3 (1 cement: 3 fine sand) (HSR 11.11.1)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (HSR 11.60)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer (HSR 11.64.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc. (HSR 11.77)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 11.78)

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied@ 3.84 kg/10 Square meter) (HSR 11.93.1)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 litre/1 O Square meter over and including priming coat of exterior primer applied @ 2.20 kg/10 Square meter) (HSR 11.95.1)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws, excludingpanelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately} 12.7.2 Kiln seasoned and chemically treated Hollock wood 30 mm thick shutters (HSR 12.7.2.2)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Kiln seasoned and chemically treated Hollock wood (HSR 12.9.2)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Float glass panes (HSR 12.9.7.1) 4 mm thick glass pane (weight not less than 10kg/Square meter).

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws: 30 mm thick shutters with ISi marked M.S. pressed butt hinges bright finished of required size (HSR 12.32.2.1.2) Kiln seasoned and chemically treated Hollock wood

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws (HSR 12.37.1)

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISi marked nickel plated bright finished M.S. piano hinges with necessary screws. (HSR 12.37.3)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding (HSR 12.50.1)

Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete. (HSR 12.58)

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm (HSR 12.98.1)

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm (HSR 12.98.2 )

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 250x10 mm (HSR 12.99.2)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 200x10 mm (HSR 12.99.3)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 150x10 mm (HSR 12.99.4)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100x10 mm (HSR 12.99.5)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm (HSR 12.102.1)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 mm (HSR 12.102.2)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 75 mm (HSR 12.102.3)

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper (HSR 12.103.1)

Providing and fixing factory made uPVC white colour sliding glazed window up to 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ±0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x B mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 Square meter up to 2.50 Square meter). (HSR 12.134.3)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) (HSR 12.157.1.3)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass /stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) (HSR 12.157.2.3)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side (HSR 12.158.1)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/Square meter) (HSR 12.159.4)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness (HSR 12.160.1)

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc.complete as per direction of Engineer-in-Charge. Polyester powder coated minimum thickness 50 micron (HSR 12.163.3)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. (HSR 12.164)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Up to 5mm depth and 5 mm width (HSR 12.169.1)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb (HSR 13.3.1.1)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile C Fixing with adjustable lugs with split end tail to each jamb (HSR 13.3.2.1)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile E Fixing with adjustable lugs with split end tail to each jamb (HSR 13.3.3.1 )

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 5.5 mm thick glass panes (HSR 13.10.2)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (HSR 13.27)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete (HSR 13.29.1)

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (HSR 13.29.2)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (HSR 13.41)

Interlocking Concrete Block Pavement Providing and Laying 80 mm thick ISi marked lntertocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect. (HSR 17.69.2)

Extra for fixing and jointing union couplings in G.I. and W.I. pipelines 25 mm internal diameter (HSR 20.23.3)

Extra for fixing and jointing union couplings in G.I. and W.I. pipelines 32 mm internal diameter (HSR 20.23.4)

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required 11.43 cm thick wall (HSR 20.26.1)

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required 22.86 cm thick wall (HSR 20.26.2)

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works 25 mm internal diametre (HSR 20.31.3)

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works 32 mm internal diametre (HSR 20.31.4)

Making connection with the existing G.I. branch main up to 40 mm size including cutting and threading pipe etc., complete excluding cost of tee and long screw, but including cartage of material to site.(HSR 20.36)

Constructing standard drain type II drain complete consisting of concrete drain moulded and laid concrete foundation, rendered and smooth with 6mm thick rendering concrete to be of I :3:6 parts by volume of cement sand stone bajri and rendering to be 1 : 1 cement sand mortar. (HSR 21.55)

Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1 :2:4 benchingb 12mm thick cement plaster 1 :2 with a floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty C.I. inspection chamber cover and frame weight as per 1.5.1. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab) (HSR 21.84.3)

Extra for every 0.30 metre depth of Inspection chamber 600 mm x 900 mm inside (HSR 21.85.3)

Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. (HSR 21.94.3) 200mm i/d

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. (HSR 22.15)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests (HSR 22.22.1)

Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required. Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern (HSR 22.26.3)

Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required. Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern (HSR 22.26.4)

Providing and fixing white vitreous chinaware extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous chinaware cistern / PVC cistern (with brass fitting) into the wall with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. (HSR 22.33)

Providing and fixing 8 mm dia C.P.S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. (HSR 22.38)

Providing and fixing toilet paper holder C.P. brass (HSR 22.42.1)

Providing and fixing partitions for different type of urinals. Small size 680mm x 330 mm White (HSR 22.50.1.1.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes (HSR 22.86.2)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes (HSR 22.86.3)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes (HSR 22.86.4)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal outer dia Pipes (HSR 22.87.5)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 62.50 mm nominal inner dia Pipes (HSR 22.87.7)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore (HSR 22.103.3)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore (HSR 22.104.1)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (HSR 22.107.1)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore (HSR 22.108.1)

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. (HSR 22.109)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (HSR 22.181)

Providing GI pipes class B marked with IS: 1239 in 3.05 m length, their threading and welding with flanges (Heavy Duty) on both sides, jointing with nuts and bolts ( 'W make), rubber gaskets, lowering into Tube wells and testing including carriage, loading, unloading etc. complete in all respects to the satisfaction of Engineer-in- Charge. 80 mm i/d (HSR 20.54.3)

Providing and fixing Ductile Iron Double seal manhole covers and frames of 610 mm x 610 mm with locking arrangement on clear water tanks including cost of setting in Cement concrete 1 :2:4 to correct alignment and levels including carriage, loading, unloading etc. complete in all respects to the satisfaction of Engineer-in- Charge. (HSR 20.61)

Providing & fixing steel bar embedded plastic steps of size 263mm x 165mm of orange colour, confirming to specification in pump chambers, manholes etc., having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS: 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1 :2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in-charge (HSR 21.28)

Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction of Engineer-in-charge. (HSR 21.94.2) 150mm i/d

Providing M.S. foot rests including fixing in manholes with 20 x 20 x10 cm cement concrete blocks 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20 mm diameter round bar (HSR 22.198.2)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 110 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.2)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 90 mm old SWR UPVC pipe lines laid complete (HSR 22.222.2.3)

Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 4Square meterm (HSR 24.5.1.3)

Preparation of mounds of various size and shapes including supply of good earth, in layers not exceeding 20 cm in depth, breaking of clods, watering each layer, dressing etc, lead up to 50 m and lift up to 1.5 m complete as per directions (excluding cost of good earth and manure which will be supplied separately.) (HSR 26.52)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/Square meter mixed with water proofing cement compound @ 0.253 kg/Square meter (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of sluny of cement @ 1.289 kg/Square meter mixed with water proofing cement compound @ 0.670 kg/Square meter and coarse sand @ 1.289 kg/Square meter This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately). For the purpose of measurement the entire treated surface will be measured. (HSR 28.16)

Flush pointing with cement mortar 1: 3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for prefixed flat tile bricks on top of mud phaska: With F.P.S. brick tiles (HSR 30.20.1)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance i!: 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main 'T'. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick bevelled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications. (HSR 32.47.3)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, up to 90 metre depth below ground level. All types of soil 300 mm dia (HSR 33.6.1.1)

Supplying, assembling, lowering and fixing in vertical position in bore well, Unplasticised PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia (HSR 33.8.2)

Supplying, assembling, lowering and fixing in vertical position in bore well Unplasticised PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia (HSR 33.9.2)

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. (HSR 33.12)

Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (HSR 33.13)

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. (HSR 33.14)

Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. (HSR 33.15)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 150 mm dia (HSR 33.16.2)

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete 150 mm clamp (HSR 33.17.2)

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I). 150 mm dia (HSR 33.18.2)

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yieldwithout sand content (beyond permissible limit), with requiredcapacity air compressor, running the compressor for requiredtime till well is fully developed, measuring yield of well by "V''notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. (HSR 33.19)

Providing and fixing factory manufactured cement concrete 1:2:4 kerb finished smooth and of size 1’-0” x 1’-0” x 0’-6” of required shape and design fixed at ground level along with road parking, complete in all respect as directed by the Engineer-in-Charge but excluding cost of cement pointing. (NS)

Earth filling under floor/road/along with boundary wall/in open area with dune sand (tiba sand), brought from outside (any lead) in 15 cm layer including laying dressing watering ramming, consolidating, excavation, carriage, loading, unloading and compensation etc. complete. (NS)

Providing and fixing PVC wall panelling consisting of 7mm thick hollow PVC section of Cactus or any other equivalent make Super Heavy (as approved by Engineer-in-Charge) PVC U-section beading of size 25mm x 8mm x 12mm and PVC angle nosing of size 25mm x 25mm x 1.5mm of Cactus or any other equivalent make (as approved by Engineer-in-Charge) including cost of PVC gutties, screws, jointed with polyfix (instant glue), complete in all respects as per drawing or as directed by Engineer-in-Charge. (NS)

Providing and fixing 12mm thick toughened glass of AIS/Modi Guard/Saint Gobain make duly toughened by standardized plant for making the cabins of different size with required holes and cut outs in fixed partition & openable panels/leaf for fully glazed single leaf doors including fixing of glass in partitions by using 3mm to 6mm wide silicon adhesive, complete in all respects as per architectural drawing and design or instructions of Engineer-in-Charge (top portion of glass partitions shall be fixed in false ceiling by making grooves of required size & bottom of glass shall be fixed in WCP. The item of WCP shall be paid separately). (NS)

Providing and fixing fittings/accessories of DORMA make as given below. {NS} Wall Connecting Profile (WCP) suitable for 12 mm thick glass DORMA XL-C-4026-A-12mmS

Providing and fixing fittings/accessories of DORMA make as given below. {NS} Central Connector DORMA XL -C 4006A

Providing and fixing fittings/accessories of DORMA make as given below. {NS} Side Connector XL - C 4008A

Providing and fixing fittings/accessories of DORMA make as given below. {NS} Corner Connector DORMA XL - C 4007A

Providing and fixing fittings/accessories of DORMA make as given below. {NS} Quadruple Connector DORMA XL - C 4009A

Providing and fixing Glass Accessories i.e Handle of size 600x30mm of DORMA make (Model XL-C 3004) including cost of stainless steel screws etc. complete in all respect as directed by the engineer in charge. (NS)

Provding and fixing Glass Accessories i.e Glass Door Package with lock (Floor Machine of DORMA make (Model XL-C 4001) including cost of Stainless Steel screws etc compete in all respect as directed by engineer in charge. (NS)

Providing and fixing frosted film of approved make, shade and colour, fixed in position on toughened glass including making design/pattern as per architectural drawing & design, complete in all respects.(NS)

Providing and fixing of C.I Grating over rain water pipe 150mm (NS)

Boring of well 10" dia size upto 200 feet deep (suitable for 9" dia PVC pipe) with suitable boring system, complete in all respect as per directions of the Engineer-in-Charge (NS)

Providing, fixing, jointing & lowering PVC blind Pipe 9" internal dia size of 10kg/cm2 pressure in borewell, complete in all respect. Make- Prince/Supreme/Skipper/Oswal (NS)

Providing., fixing, lowering & jointing PVC slotted/perforated Pipe 9° internal dia size of 10kg/cm2 pressure (in the bore hole) of Prince/ Supreme/Skipper/Oswal make with PVC filter jali and dhaga etc. duly wraped over PVC perforated pipe, complete in all respect. (NS)

Providing and fixing PVC end cap (for 9" i/dia PVC pipe) of Prince/ Supreme/Skipper make complete in all respect. (NS)

Providing and fixing copper revitts of best quality as per required, complete in all respect. (NS)

Providing, fixing 12.5 HP capacity submersible pumping set of 3 phase, 3-stages with 3" i/dia delivery complete in all respect of KSB/LUBI/Kirloskar make. (NS)

Providing and fixing in position MS Panel Board suitable for 20 HP capacity submersible pumping set consisting of starter of suitable capacity, ampere Meter, volt Meter, indicator lamps, MCBS, connecting wires etc. of suitable in all respects. (NS) Make-Havells/L&T/Siemens

Providing and fixing base plate (Heavy duty) of required size, complete in all respect. (NS)

Development of tubewell bore for atleast 12 hours (or till develop of cavity) by using suitable engine/pump/system complete to the satisfication of the Engineer Incharge. complete in all respect. (NS)

Providing and fixing MS clamp (Heavy duty) 250 mm i/dia size suitable for 9" i/dia pipe with nuts & bolts etc., complete in all respect. (NS)

Providing and fixing of underground cable, 1 meter below G.I. covered with sand and bricks including necessary connections, digging, and refilling etc., complete in all respect. (NS) 16 Square meterm 4 core cable (Armoured) Make:- Havells/CCI etc.

Providing and fixing in position PVC specials 100 mm inner dia Head Rest bend. (NS)

Providing and fixing in postion PVC special 100 mm inner dia coupler. (NS)

Provding and laying brick bats and brick ballast. (NS)

Providing and fixing in postion V. Chinaware W.H.B. (Table Tap) (Aviator) Italian White of Hindware make of size 59.50 x 42 x 15.5, Cat No., Star whie. (NS)

Supplying and fixing of PVC floor traps (Heavy Duty) of 90 mm o/d outlet of Prince, Supreme, Skipper make complete in all respect. (NS)

Supplying and fixing of PVC floor traps (Heavy Duty) of 100 mm o/d outlet of Prince, Supreme, Skipper make complete in all respect. (NS)

Supply and fixing of CPVC Union coupling with brass internal fitting, complete in all respect. For 25 mm nominal outer dia pipes. (NS)

Supply and fixing of CPVC Union coupling with brass internal fitting, complete in all respect. For 32 mm nominal outer dia pipes. (NS)

Supply and fixing of CPVC Control/Ball valves with brass internal fitting, complete in all respect. For 25 mm nominal outer dia pipes. (NS)

Supply and fixing of CPVC Control/Ball valves with brass internal fitting, complete in all respect. For 32 mm nominal outer dia pipes. (NS)

Providing and fiixing PVC water pipe 40 mm i/dia size approximately 3 inch long (Heavy Duty) with coupler embeded in wall complete in all respect. Make:- Supreme, Skipper, Prince. (NS)

Providing and fixing looking miror 5.5 mm thick in different sizes mounted on asbestos sheet ground fixed in position by means of 4 Nos. C. P Brass screws and CP brass screws etc. complete in all respect. (NS) Make:- Saint Gobain/Modi/Aftul

Providing and fixing CP grating 5" i/dia size of best quality, complete in all respect. (NS) Make:- Supreme, Skipper, Prince

Providing and fixing of PVC elbows of following sizes of Prince/Supreme/Skipper make. (NS) (i) 110 mm o/dia (4" i/dia)

Design, Providing and fixing of Reception Counter of Size of 6 feet long x 2 feet 6 inch deep x 4 feet High consisting of 12mm thick BWR grade - II (ISI Mark) Ply-wood (Make: Century Ply/ Greenply/ Kitply) finished with 1mm thick plastic Laminate sheet of approved shade and colour (ISI Mark) and table top finished with 15 to 18 mm thick White Acrylic Corian worktops fixed on wooden surface with suitable adhesive in any pattern complete in all respect as per approved drawings ; Branding of CCS HAU AGRO TOURISM CENTER in Acrylic Cut Backlit 3-D Letters of required height as approved by Engineer in charge. (NS)

Providing and fixingi of Backdrop Curved Both side partition wall at all heights made up heavy duty Class-B MS Frame of 50mmx50mm; Upto thickness of 2mm. Including cost of cutting wheel, red oxide, fasteners, MS plate 6mm thick of size 100 mm x 100 mm, anti termite treatment, solution, nails, screws, 2mm thick tape, ; Cladding of Ply-wood of 9 mm of BWR Grade-II (ISI Mark) of approved make fixed on the Ms Frame ussing all neccessary tools & Machines; Veneer of 4mm thickness with PU Polish to be installed on the Ply base using suitable adhesives complete as per entire satisfacton of the Engineer-In-Charge. (NS)

Providing and fixing Two dimensional thematic Mural with low and high FRP relief of 6 mm Thickness of 300-450 matt finish painted as per Approved Artwork suitable for outdoor installation with limited decorative materials like glass, acrylic, metals of various types and finishes, duly finished as per Approved Artwork. The design will contain both decorative and figurative elements. The 2 dimensional thematic mural with relief shall be detailed as per concept design and produced as per approved shop drawings, sketches, artworks and suitable visual represenations to be supplied by the agency. Production may be on-site or off-site or both and shall be assembled and installed at site at locations as instructed.The mural shall adhere to all structural stability and public safety norms . Item to include all material, labour and carriage in all leads and lifts complete as per entire satisfacton of the Engineer-In-Charge. (NS)

Providing and fixing of Digital Translite with LED backlit arrangement, clip on system including printing, lamination and mounting on a polycarbonate 0.40 mm sheet fitted in box with lighting arrangement. (NS)

Supplying and fixing in position Commerical Series LED Screen 55" (Make: Samsung/Sony/LG) 16*7 of 4k Qaulity, complete. (NS)

Providing & Fixing of Heavy Duty Cast Iron VIP Bench, 3 Seater of Size : 6 feet long and seating area 1.5 feet deep of a minimum weight of 150 Kg, embedded in Cement Concrete 1:1.5:3 Blocks. With Arm Rest & Backrest. Appearance Modern; Load Capacity Minimum :200 KG, complete as sample approved by the Enginer in charge. (NS)

Providing and laying flat 1st Class machine made brick (Brick Size: 9 inch x 4 inch x 3 inch) in flooring over upto 150 mm thick bed of lean concrete 1:5:10 ( 1 cement: 5 coarse sand: 10 gradded stone aggregate) with Groove Filling of FRP 10mm-12mm wide & 12 mm Deep, complete in all respect as directed by Engineer in charge. (NS)

Providing & Fixing of Tree House (Approximately 4 meter x 3.5 meter with a height of 3 meter; variation +/- 5%) Consisting of : Tree Hut on a approximate height of 4 Meter from ground level. Installed on Support of existing trees/ Fabricated Artificial Trees of Heavy duty MS 6" Pipe of C-Class with Tubluar truss of MS Hollow section of size 65mm x 65mm of 14 Guage as per apprroved drawings with a suitable load capacity Cladded with FRP with a girth of a size artistically and structurally suitable. Accessible by MS Staircase With a tread of 300mm and Riser of 150-180 mm & a length of 1000mm of MS Sheet of 4mm thickness Epoxy Painted complete in all respect. FRP Thematic Slant Roofing (For a rural Outlook) on MS framework of Section of 50mm x 50mm ; thickness upto 2mm Including cost of cutting wheel, Epoxy Paint, fasteners, MS plate 6mm thick of size 100 mm x 100 mm, anti termite treatment, solution, nails, screws, 2mm thick tape, etc. complete in all respect as directed by Engineer-in-charge. With Wooden plank Flooring of commercial hard wood such as Hollock, Champ, Chikrasy of 25mm thickness on on a Ms Frame Structure of section 50 mmx 50mm with WPC Cladded Base with FRP coating to match thematic scheme . Epoxy coating as per Engineer-in-charge.Adequate windows & opennings, Base plate & Anchors, complete in all respect to be provided as per the approved structural drawings or as per the instruction of Engineer-In-Charge. The above work is excluding civil work related to foundation which shall be paid separately. (NS)

Food Junction Eating Area Gallery of 80 feet Dia. Roof Fabricated with MS Frame of 2"x2" Including cost of cutting wheel, Epoxy Painting, fasteners, MS plate 6mm thick of size 100 mm x 100 mm, nails, screws, 2mm thick tape, cladded with Hybrid WPC then coated with FRP Thatched Roofing (Rural Outlook) supported by Ms Columns of 6" dia with FRP Cladding complete with designing and thematic artwork with moulded formed work min 6mm thick 300-450 fibre matt including Paint work as per theme finishing with fibre putty. including seating like 04 traditional khaat, 08 traditional Mudhe of approved size and central table of 4 feet Dia made of tree stem of approved design. All surfaces to be covered with WPC with FRP Cladding complete with designing and thematic artwork with moulded formed work , complete work as per directions of engineer-in-charge. (NS)

Construction of approcah pathway consisting of cobble stones of required shape, colour and size grouted with white cement to be laid on 4 inch thich plain cement concrete 1:8:16 including brick toe wall , complete in all respect as directed by Engineer in charge. (NS)

Artwork Development : Artwork development and graphic design for large scale scenic images as per site requirement comprising of layers and cutouts wherever required. The content of the artworks shall be created as per approved concept doCubic meterent and public sentiments where necessarry. The output shall be high resolution print ready soft files and prints in 1:4 scale colour printouts for approval. Cost of print media, proof checking/ revisions, handling, carriage, taxes etc.complete in all respects and as per directions of Engineer in Charge.. Tracing of artwork may be required to be inserted in the relevant elevation in CAD where the artwork is to be utilised. Mode of measurement will be flat elevation area / open elevation area as per CAD drawings or physical measurement on 1:1 actual size bases, irrespective of layers and cutouts. Final submission of approved final artworks will be made in a commonly used open format . Only For the work of sculpture, Murals. (NS)

3-D Diorama Creating & Transcending plain décor of photo to life like 3D effect using all required materials like Hybrid WPC Cladding (12mm), FRP Cladding of 6mm thickness, MS Frame work of suitable structural requirements & finishing for the diroma as per with conceptualization, designing and approved drawings the fabrication cost of material & labour inclusive of all models as per theme/Drawings complete in all respect as approved by Engineer-In-Charge. (NS)

Interactive Kiosks,of size 2.5 feet Long x 2.5 feet deep x 3 feet High with Microprocessor controlled intelegent unit where display comes on full HD 23 inch monitor with touch of finger on screen duly fitted in a designer wooden/metalic console having a provision of CPU of Specs : 12th Gen Intel Core i5 with windows 10 Pro, 8Gb Ram DDR4, 256GB PCIe NVMe Class 35 Solid State Drive (EM) in a solid casing with all neccessary cables & wires (with keyboard). Touch Screen Size: 23" , including inbuilt UPS of Microtek/ V-Guard/Luminous make & Exide make baterries having 30 Minute backup time. Designing of interactive software for interactive Kisosk, complete the job in all respect as directed by Engineer in charge. (NS)

Providing & Fixing Showcases consisting of center/ corner showcases need to provide a study , secure enviorment as free as posible from dust , pets , pollution and heat . They must also be easy to open so that the displays can be maintained & modified with ease. High Security conservation showcase with single mechanism pull & slide door . Wall Mounted high security conservation showcase- (wooden/metallic) Table top high security conservation showcase-Lift off or Hinged canopy Made up of waterproof plywood (Duro/century/merino/green/arched/kitply etc. Laminated with teak/ sunmica or polyester powder coated Extruded profiles with 8mm clear Toughened glass of Saint Gobain, Modi or equivalent complete with Stainless Steel Fittings of 304 Grade, fixtures, LED lighting arrangemet & labour. The depth for the showcase: 1.5 feet, complete including other hardwares as per approved drawings or as per the instructions of Engineer-in-Charge. (NS)

Construction of wooden bridge of a width of 6 feet with a length as per site requirement placed on a existing structure over the proposed wetland with existing frame structural steel girders fitted with base plate, on prepared RCC foundations as per the structural drawings, joined with horizontal MS beams, finished over by wooden planks and MS (C- Class) Railing of section 65MM x65MM With base prepration to support a load of 800kg.With FRP Cladding on all surfaces, complete with designing and thematic artwork with moulded formed work min 6mm thick 300-450 fibre matt including Paint work as per theme (Make: Asian,Berger,Nerolac) finishing with fibre putty , complete in all respect as per the approved drawings or as per the directions of the Engineer-in -charge. (NS)

Providing and fixing of Life size Maniqueins of Human beings made of FRP of 4-6 mm thickness including concrete platform cladded with 15-18mm granite of any colour & quality including nosing, champering, polishing etc, complete in all respect as directed by Engineer-In-Charge. (NS)

Providing and fixing of Life size Maniqueins of Animals made of FRP of 4-6 mm thickness including concrete platform cladded with 15-18mm granite of any colour and quality including nosing, champering, polishing etc, complete in all respect as directed by Engineer-In-Charge. (NS)

Supply and insttalation of floor mounted sculpture of Bronze (Composition: 85% Copper, 5% tin, 5% zinc, 5% Lead) of 10' to 12' high Logo of CCS HAU or any indicative design approved by Engineer-In-Charge. (NS)

Construction of Mushroom Shaped Resting Sheds in mild steel structural hollow sections and mild steel wire mesh as per the design with red oxide paint finish & FRP Mushroom Themed Roofing including Suitable fittings with an outer diameter of 10ft with sitting of height 16" of dia 6ft, Height of the Structure from Natrual Ground Line shall be 12ft High. Cement Concrete sitting with 15-18mm Granite of any colour in flooring, cladding on all surfaces of seating including nosing, champering, polishing, including all related civil work etc as per approved drawings complete in all respect as per Instructions by Engineer-In-Charge. (NS)

Decorative Water Pool in a amoeba form(Size of 6m Diameter) with Artificial Water Fall out of a Fibre Sculpture placed on a 10 ft Dia Island with a height of 8ft as per approved artwork including lighting to illuminate the water fall at night time (RBG 30w Lighting with light decorder/controller with input voltage of 240v, frequency of 50hz, Ip-66, ta 45 Degrees Celsius) including all plumbing works like installation of piping, pump etc. the work also include all civil work like excvation, brick work etc the pool interior walls to be cladded with mosiac tiles (Providing, laying & fixing). Including the cost of life size fibre sculpture exhibiting REHAT with accessories with life size OX, FARMER complete as per approved drawings or as per instructions given by Engineer-In-Charge. (NS)

Providing and fixing of 20 liter Dustbins with fibre decoration based on the theme embedded in cemenct concrete blocks and two different bins for seperation of waste of approved make lile Neelkamal, Sintex etc complete as per direction of Engineer in charge. (NS)

Trompe l'oeil , hand painted on canvas with acrylic paint medium with matt finish clear protective varnish/enamel painting as per approved artwork and include packing, transportation and installation at site inclusive of all consumables, adhesives, tools etc. Mode of measurement will be elevation area.. Item to include all material, labour and carriage in all leads and lifts complete as per entire satisfacton of the EIC. (NS)

Providing, fabricating and placing Hybrid WPC cladding with 12 mm thickness of approved brand and manufacturer onto existing MS frame work / masonary wall, on to existing base at all levels including handling, carriage finishing of rear side with one coat of primer, of approved brand and providing holes as required for services etc. complete as per brief/design concept/model/prototype/drawings and as per directions of Engineer-in-Charge. The contractor shall submit fabrication drawings for art work involved based on construction drawings (that may be issued during construction period) for approval by the Engineer-in-Charge. (NS)

Wall Aquarium of size 12 feet x 2 feet x 8 feet made up Security glass of required thickness (18mm to 25mm) box with 304 grade Stainless Steel angle framing with filter, pebbles, artificial plants, air pump & wallpaper including cost of tools, labour & fixing complete in all respect as per insturctions by Engineer-In-Charge. Note: Structural stability certificate from Structural engineer will be requried. (NS)

FRP Cladding on existing surface. complete with designing and thematic artwork with moulded formed work min 6mm thick 300-450 fibre matt (Make: Benani) including Paint work as per theme (Make: Asia,Berger,Nerolac). finishing with fibre putty, complete in all respect as per Engineer-In-Charge. (NS)

Providing, fabricating and placing ply cladding with 12 mm thickness of approved brand and manufacturer onto existing MS frame work / masonary wall, on to existing base at all levels including handling, carriage finishing of rear side of ply with one coat of ply primer, antitermite treatment of approved brand and providing holes as required for services etc. complete as per brief/design concept/model/prototype/drawings and as per directions of Engineer-in-Charge. The contractor shall submit fabrication drawings for art work involved based on construction drawings (that may be issued during construction period) for approval by the Engineer-in-Charge.12 mm ply make: Kit Ply, Century, Greenply,Duro. (NS)

Providing and fixing 50 mm Thick Pink Dhaulpur stone (BANSI PAHARPUR Variety) jali made in approved design fixed with required mortar mixed with color pigment fixed with copper clamps or dowels, complete in all respect as directed by Engineer-In-Charge. (NS)

Providing & Fixing of Fountain of Length 20 ft, with a height of 20ft including 20ft novel hydra including brass crome plated nozels (Approximately 40 Nos.). The fountain will have RGB Color changing submersible lights with controller (16 Nos.). 5HP Mortor of standard make with motor controller, complete in all respect with all fitting accessories to be provided as per approved drawing or as per instructions of engineer incharge. The work is excluding all civil work. (NS)

Providing & fixing of Glass waterfall consisting of : Size 16ft X 8FT with toughned glass of 8mm thickness ( adequate Frame ) 16Ft SS tank, SS frame , SS Net cover and SS Nozel hydra (SS Grade of 304) Motor hoti 1 HP with motor controller with all fittings and accessories. RGB colour changing lights with controller, Complete in all respect as per approved drawings or as per instructions by Engineer-In-Charge. (NS)

Providing and fixing of Acrylic letters of 3 ft Height (as per approved artwork/FONT) placed on a existing podium of 2ft height of brick masonry cladded with 15-18 mm Granite of approved shade and quality by Engineer in charge at the time of execution of work. The letters will back lit LED’s placed over sun board base over and above ACP base ,SIDE EDGES(4’’) :-5 mm transparent white acrylic sheet with laser cut(using AMADA Laser cutting m/c) & 4inches manual Raising all around with details.ACRYLIC SHEETS & ITS TECHNICAL PARAMETERS:- Front: a. 5mm White imported (Mitsubishi/equivalent) acrylic cutting on laser cutting machine. b. The illumination percentage of 040 white acrylic is 51(min) c. Flexi bond make 25mm Sun board for the Round logo and back of the Letetrs. ( (sheets Cutting shall be on CNC router machine only).Acrylic letters shall have 5 mm thickness Imported white color with laser cuts , 2’’ rim right around the letters ,front and fully covered with acrylic materials. L.S 1 c letters can be in Hindi/English. NOTE: 01 Number LED Driver of Each letter will be supplied extra free of cost. (NS)

Conceptualization & creating the concept of Agro Turism Center Including Architectural drawings/Economical Structural design/drawings (of all civil strucutres ) as per IS 456 including proof checking any recognize government institute i.e NIT's / IIT's, Electrical Installation/Public Health/Sewage System/ CCTV/LAN/Horticulture/Rain Water Harvesting, roads and any other Allied Services drawings based on eco friendly, energy efficient and green building concept, Soil Investigations including testing of soil for harmful sulphates and bearing capacity, site survey, Script writing / Visualizatoin & Graphics Presentation / Shop Drawings/Electrical Drawings/Plumbing Drawings/Civil Drawings/ Topography etc. The layout plan/ orientation of civil strucutures should be got approved from the Engineer in charge of the work before the start of the work. (NS)

Electrical work 237 to 365:- Copper Wiring With Modular Switches in PVC Conduit Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group B (HSR 23.4.1.2)

Copper Wiring With Modular Switches in PVC Conduit Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group B (HSR 23.4.2.2)

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group B (HSR 23.4.4.2)

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group B (HSR 23.4.5.2)

Supply and erection of MS conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. MS Pipe of 20 mm dia (HSR 23.6.6.1)

Supply and erection of MS conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. MS Pipe of 25 mm dia (HSR 23.6.6.2)

Supply and erection of PVC conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 20 mm dia. (HSR 23.7.6.1)

Supply and erection of PVC conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. (HSR 23.7.6.2)

Supply and erection of PVC conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 40 mm dia. (HSR 23.7.6.4)

S/E of Fittings and Accessories. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect Call bell 220/230 volts musical type (HSR 23.8.1.6)

S/E of Fittings and Accessories. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect Bakelite angle/straight button holder large size. (HSR 23.8.1.12)

S/E of Fittings and Accessories. Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S. Road made into suitable suspension hook and erected in R.C.C.slab for the erection of fan complete with all labour and material required to complete the job. (HSR 23.8.4)

S/E of Fittings and Accessories. Providing and fixing GI concealed sheet metal boxes with inner and outerface plate including concealing the box in wall and fixing in position withinner plate and face plate with all labour and material required for the jobcomplete in all respects. 1 & 2 Modules (HSR 23.8.10.1)

S/E of Fittings and Accessories. Providing and fixing GI concealed sheet metal boxes with inner and outerface plate including concealing the box in wall and fixing in position withinner plate and face plate with all labour and material required for the jobcomplete in all respects. 3 Modules (HSR 23.8.10.2)

S/E of Fittings and Accessories. Providing and fixing GI concealed sheet metal boxes with inner and outerface plate including concealing the box in wall and fixing in position withinner plate and face plate with all labour and material required for the jobcomplete in all respects. 6 Modules (HSR 23.8.10.3)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch (HSR 23.8.11.1)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket (HSR 23.8.11.4)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp Socket (HSR 23.8.11.5)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. step type Fan Regulator 2 modules 300 watt (HSR 23.8.11.7)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Telephone Socket outlet modular type (HSR 23.8.11.8)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. TV Socket (HSR 23.8.11.9)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate (HSR 23.8.11.10)

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type (HSR 23.8.11.11)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work Double pole MCCB 16 to 63 Amp, 25 Ka (HSR 23.22.1.1)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the workTRIPLE POLE MCCB 16 to 100 Amp, 25 KA (HSR23.22.1.3)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the workTRIPLE POLE MCCB 200 to 250 Amp, 25 KA (HSR 23.22.1.5)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 12 way (HSR 23.22.4.3)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 16 way (HSR 23.22.4.4)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 + 12 ) (HSR 23.22.4.5)

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 8 way (8+24) (HSR 23.22.4.7)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- SP MCB 6-32 AMP (HSR 23.22.5.1)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- SPN MCB 6-32 AMP (HSR 23.22.5.3)

MCCB ,DISTRIBUTION BOARDS, MCB’s, RCCB's, CHANGE OVER etc. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- TPN MCB 40-63 AMP (HSR 23.22.5.6)

Supply and fixing Galvanised Iron flexible pipe complete with socket nipples and check nuts etc.at both ends (Upto length of one metre):- Size 20 mm dia (HSR 23.23.1.2)

Supply and fixing Galvanised Iron flexible pipe complete with socket nipples and check nuts etc.at both ends (Upto length of one metre):- Size 25 mm dia (HSR 23.23.1.3)

Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channe l and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-incharge of the work. 2 pair telephonewire (HSR 23.23.8.1)

Supplying and drawing of 1no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required (HSR 23.23.9)

EARTHING AND LIGHTINING ARRESTOR Earthing with G.I earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. as required. (HSR 24.1.1)

EARTHING AND LIGHTINING ARRESTOR Extra for using salt and char coal/coke for pipe earth electrode as required. (HSR 24.1.2)

EARTHING AND LIGHTINING ARRESTOR Earthing with G.I. earth plate 600mm x600 mmx 6 mm thick including accessories and provinding masonry enclosures with cover plate having locking arrrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required. (HSR 24.1.3)

EARTHING AND LIGHTINING ARRESTOR Extra for charcoal or coke and salt for G.I. plate earth electrode. (HSR 24.1.5)

EARTHING AND LIGHTINING ARRESTOR Supplyingandlaying25mmx3mmG.I.stripin40mmdia,GIpipeas/from earth electrode including soldering etc. asrequired. (HSR 24.1.7)

EARTHING AND LIGHTINING ARRESTOR Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connectionsetc.asrequiredwithalllabourandmaterial. (HSR 24.1.8)

EARTHING AND LIGHTINING ARRESTOR Pdg and laying earth connections from earth electrode with 4.00 mm dia G.I wire in 15 mm dia G.I. pipe from earth electrode as required. (HSR 24.1.11)

EARTHING AND LIGHTINING ARRESTOR Providing and fixing 4.00 mm dia G.I. wire on surface or in recess for loop earthing as required. (HSR 24.1.13)

LT CABLE Supply and erection of suitable compression type brass cable glands for underground Cable :- 10 sqmm to 16 sqmm cable 2 to 4 core (HSR 24.2.7.2)

LT CABLE Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50 sqmm cable 2 to 4 core (HSR 24.2.7.3)

LT CABLE Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 10 sqmm (HSR 24.2.8.3)

LT CABLE Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 16 sqmm (HSR 24.2.8.4)

LT CABLE Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm (HSR 24.2.8.5)

LT CABLE Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 50 sqmm (HSR 24.2.8.7)

LT CABLE Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 95 sqmm (HSR 24.2.8.8)

LT CABLE Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 185 sqmm (HSR 24.2.8.9)

STREET LIGHT B.S.E.N.10025 High Masts Supply, installation, testing and commissioning of 12.5 mtr. longHigh Mast manufactured from B.S.E.N. 10025 or equivalentgrade material in, 2 (two) section hot dip, galvanized inside andoutside in single dip, suitable for wind velocity as per IS 875Part-3 suitable for 6 nos. luminaire loading fully motorized(power tool) with starter & cable complete along with standardaccessories supplied by the manufacturer with 3 nos. steel wirerope double drum system and twin dome aviation light with LEDwithout foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entiresatisfaction of Engineer -in-Charge Thickness of Top and Bottom Section = 3 mm (minimum) Top Dia = 150 mm and Bottom Dia = 360mm Thickness of Galvanization - Top = 65 micron (minimum) and Bottom = 85 micron (minimum) (HSR 24.4.15.1)

S/E of mark double walled corrugated ( DWC) HDPE pipe 10 kg/sqcm, laid 0.75 Mtr. Below ground level including diging and refilling of earth including cost of suitable size socket/ cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer incharge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia (HSR 24.5.2.3)

S/E of mark double walled corrugated ( DWC) HDPE pipe 10 kg/sqcm, laid 0.75 Mtr. Below ground level including diging and refilling of earth including cost of suitable size socket/ cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer incharge of the work. DWC/HDPE pipe 90/75 mm outer dia/inner dia (HSR 24.5.2.4)

RCC FOUNDATIONS FOR HIGH MAST OCTAGONAL POLE Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 75 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for high mast octagonal poles of various heights as per following soecifications complete in all respect and as per directions of Engineer-in-Charge 12.5 m high mast pole (HSR 24.9.1)

S/E of pipe for wiring purpose including bends inspection boxes etc. where necessary and painting as required:- (xxx) S/E of PVC pipe of 6 kg. pressure, laid 1 metre below ground level including digging and refilling of the trech completing with joining with jute and cement etc. (b) PVC pipe 80 mm dia. (NS)

Supply & erection of under ground cable 1 mtr below ground level with sand & bricks complete with necessary connecitons:- (i) 10 sq mm 2 Core cable (Armoured) (NS)

(ii) 16 sq mm 2 Core cable (UnArmoured)

(iii) 16 sq mm 2 Core cable (Armoured)

(iv) 16 sq mm 4 Core cable (Armoured)

(v) 25 sq mm 4 Core cable (Armoured)

(vi) 50 sq mm 4 Core cable (Armoured)

(vii) 95 sq mm 4 Core cable (Armoured)

Supply & erection of under ground cable lose in existing pipe or trenches complete with necessary connecitons:- (i) 10 sq mm 2 Core cable (Armoured) (NS)

(ii) 16 sq mm 2 Core cable (UnArmoured)

(iii) 16 sq mm 2 Core cable (Armoured)

(iv) 16 sq mm 4 Core cable (Armoured)

(v) 25 sq mm 4 Core cable (Armoured)

(vi) 50 sq mm 4 Core cable (Armoured)

(vii) 95 sq mm 4 Core cable (Armoured)

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe. (i) ( Size 1.5 sqmm(3/0.81mm) (NS)

(ii) (Size 4 sqmm(7/0.85mm)

Supply installation testingan commissioning of wall free standing floor mounting dust & vermin proof compartmentalized cubical panel made out of 2 mm thick CRCA sheet required hardware 3 mm thick bakelite sheet providing all along the bus bar and cable alley separating switches compartment and supporting suitable channel duly painted by 2 coat of zinc/Red oxide primer followed by 2 coats of powder cating in grey or required shade after rinsing. the panle having PU/Neoprene rubber gasket of not less than 3 mm thickness separate detachable gland plate MS base channel hinged door with inter locking arrangement for equipment/ switch wear.Transparent arcylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3 mm thick for separately cable alley to BBC from switch chamber Extended solid copper bars up to cable alleys shall be provided for outgoing connection which shall be paid as extra tiems side walls and cable alley compartments shall be haiving bolted type doors with detachable extension type strcture. the panel will be complete with control wiring ( copper) and fuse protection ( only outer area on all sides shall be measured ) (NS)

Supply and fixing of copper bus bar duly tinned by means of SMC/DMC type insulator high tensile nuts and bolts spring washers fixing go same in existing panel including bending, cutting in required shape and size and insulation with colour coding heat srinkable PVC insulation complete in all respect. (NS)

S/E of AC ceiling fan capacitor type complete with shackle 5 star rating, 300mm down rod etc. (NS) i) 1200mm sweep. Make: Usha, Orient, Crompton

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod etc. (NS) i) 1400mm sweep. Make: Usha, Orient, Crompton

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod etc. (NS) i) 900mm sweep. Make: Usha, Orient, Crompton

S/E of LED Flood light of system voltage ≤ 250 W IP 66 Multiple LED with lens optics and pressure die-cast aluminium housing for effective thermal management. Total system lumen of ≤ 250 watt LED should be 31250 lumen or above in cool day light (5700K), Lumen efficacy > 110 lm/W, Power factor ≥ 0.95, CRI ≥70, Average life ≥50000 hours, complete with all acessories as required with connections. Make Havells , Bajaj , Philips. (NS)

S/E of LED tube rod < 20watt double side connections with 4 feet long housing made of CRCA sheet steel with epoxy powder coated white after phosphochromate treatment and 2 nos. lamps push fit type white polycarbonate holders and reflector made of white powder coated CRCA sheet total system lumen of 20watt LED should be >2200 or above in cool day light ( 3000K ) PF > 0.95 , CRI >80 , Avg. life >50000 hours complete with mounting bracket and accessories as required with connections Make Philphis , Havells , wipro , Bajaj ( NS )

SITC of astronomical time switch degree of protection IP 20 two module voltage 230 V AC, 50 Hz Astronomical programmable every one minute back up of 6 years 28 memory locations, current capacity 16A with 1 changeover (ICO) total 28 programmes. Ambient temperature -10 degree to +55 degree with 32 amp. contactor three phase with 32 amp. DP MCB and 25 amp. SP MCB. (NS) Make: Indo Asian,Phillips,Havells,Wipro,Bajaj etc

SITC of 9 Mtr Long Trudge M in 120 W with Six Angular bracket module each of 120W , homogeneous light distribution suitable for landscape area , led lumen output is more than 125lm/ watt with life cycle of 50000 hrs can be mounted on 9 mtr height pole. Every module is in angular shape and produce diffuse light in 120 degree complete fixture is made up of die cast aluminium and proper heat sink on every module complete fixture is weather protected and suitable for outdoor application . Fixture is with Osram / Samsung Led and PHiliphs/ meanwell / Fulham diver. Fixture dia with bracket is 1124mm. Fitting is with all the accessories required for mounting. VAT-PT-TUR-M-POST-120 Code (NS)

S/E of recessed type 42 watt full window glare free opal difffuse LED panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 5100 or above in cool day light (5600k to 6500k), Power factor >0.95, CRI (Ra) >80, LED lamp efficiency ≥140 lm/w, Average life >50000hours, complete with all accessories as required with connections.Code :- PLANO2*2PLR42WLED865S (Industrial) Make Havell's or Philiphs , Bajaj (NS)

Supply and erection of 120W LED flood light having following specification IP voltage –AC 100-265V, total power consumption – 50 W (i/c driver), Lamp Luminous efficiency - >110 lm/W, Lumens - >13200 lm, Colour-cool white, CCT - 5000-6000K, CRI-more than 70, operating tempracture = -35°C to + 50°C, IP rating luminiare - IP65, IP rating LED module - IP67, power factor = ≥0.95. Complete in all respect with the entire satisfaction of Engineer-in-Charge. (Make: Havels , Bajaj , Philiphs). (NS)

Supply of Single phase propeller type ventilating fan (Exhaust fan). No. of pole 6 sweep size 300mm 900/1400 rpm with louver complete in all respect Minimum one year gurantee/warantee. (NS) (Make: Orient/Hevells/GEC).

Supply, erection of 0.51 mm jelly filled armored telephone cable laid one mtr. below ground level including the cost of digging, bricks, rawl & laying charges, complete in all respect with the entire satisfaction of Engineer-in-charge. (Make: Delton/Finolex). (NS) 20 Pair

Supply, erection of 0.51 mm jelly filled armored telephone cable loose in existing pipe/tranches including testing & commissing charges, complete in all respect with the entire satisfaction of Engineer-in-charge. (Make: Delton/Finolex). 20 Pair (NS)

10 pair (NS)

5 pair (NS)

Supply, erection, laying and testing of D.P. including the cost of krones, base plate, 40mm dia G.I. pipe for incoming and outgoing cable and main box having locking arrangement. 20 pair DP (NS)

10 pair DP (NS)

5 pair DP (NS)

Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S. sheet fixed with rag bolts on wall or on existing pedestal/angle iron frame including bonding to earth, detachable top and bottom painting and necessary connections etc. (Copper bars duly tinned) (NS) 100 amp.4 bars of 55 cm each (cross Section 25 mm x 3 mm ), chamber over all size 60 cm x 45 cm x 18 cm

800amp.4 bars of 55 cm each (cross section 50mm x 10mm), chamber over all size 60cm x 70cm x 38cm) (NS)

Supply and erection of 3 core PVC copper insulated and sheathed circular flexible wire Size 1.50 sq mm (48/0.20 mm) (NS)

Supply, Installation and commissioning of 1 x 10 KVA UPS Each UPS of 10 KVA/8 KW should have following specifications in addition to tender requirements : True online double conversions, IGBT Rectifier & inverter based UPS. Three phases Input/ three phase output with SMF batteries Suitable for 30 Min backup on Full load (20 KVA) at 0.8 output power factor. Input voltage range 360-478V at 100% load, 220-478 V @ 50% load. Input power factor 0.99,Output THD is less than 3% for linear load. Less than 5 % for nonlinear load. Crest factor 3:1, over load 125% for 10 min, 150% for 1 min and should be able to operate continuously at 115% load on bypass mode. Battery voltage Adjustable from 384VDC to 480 VDC on site. Battery Bank sizing as 42 AH x 40 nos. X 1 String. Battery type should be Valve regulated lead-acid (VRLA) of make Exide/Panasonic/QUANTA/Rocket. Audible noise level should not exceed 63 dB (A). Parallel communication port, RS232. USB EPO and SNMP interface, BMS interface are required. EMC-IEC62040-2 safty-IEC62040 II operating temperature 0-40 deg C, relative humidity 95% Non-Condensing. No derating e to 40 Deg temp.. UPS shall have inbuilt Input Isolation Transformer. static by pass and manual by pass built in required. Third party test report through accredited lab like TUV is required for IEC 62040-3 and IP20. UPS should be provided with environment monitoring probe to measure temperature and humidity of UPS room. UPS shall have dust filter sat Air Inlet level to improve UPS reliability. LCD Display indicating all important parameters. SNMP software should be compatible to Microsoft windows XP, Windows Vista, Window 8, Window server 2003 R2, UPS software should be compatible to google chrome, Mozilla fire fox and Microsoft internet explorer. Battery rack, battery interlinks battery breaker, battery to UPS cable as required should be provided with UPS systems. (NS) Make: Elnova, Eaton, Peagasus,GE,Gutor

Pdg. And installing split type air conditioners, five star rating inverter type with copper coils 2.0 ton capacity ± 10%) fitted with super tropical DC PAM inverter -return cooled- rotary compressor operating on refrigerant R-140-A suitable for wall mounting confirming to IS: 1391 (part-2)/92 (except power consumption norms) with upto date amendments, suitable for operating on 230 volts, 50 Hz single phase A.C. supply having following specifications:- (i) Cooling coil row-3 Nos. (ii) Air Flow (CMH) -1450 cum/hr. (iii) Sound level (H/M/L)- 41/38/34/25(silent mode) (iv) Louvers swing- 3D+3D Auto etc. complete in all respect. Make:- O General /Toshiba/Mitsubishi(Heavy Industries) (Five Star rating ) Model as approved by the Engineer-in-Charge. (NS)

Pdg. & installing of automatic voltage stablizer of 5 KVA 100Up copper wound including all material required to complete the Job in all respect. Make Voltstar , Microtek (NS)

Pdg & fixing in position powder coated M.S. Stand (NS)

S/E of fancy pole 3 mtr. Long made out of cast iron base part and miled steel grooved pipe section and joined together by means of threaded joints alongwith a service window provided in the bottom part of the pole to accommodate a 6 amp. SP MCB and 30 amp. connector for mains connection. A cast aluminium embellishment shall be fitted to the grooved steel pole by grub screw fixing to enhance the decorative look of the pole. The pole shall be duly pre-treated by shot blasting process and painted in poly - urethane paint in approved colour shade having a minimum 300 salt spray hours quoting on the pole and should have minimum 90 micrones DFT. Pole Make: Twinkle, Homdec Lighting LED Specifications: LED should be ≤30 watt with cast aluminium housing diffuser translucent poly carbonate having quoting PU/Polyster LED should be ≤ 30 watt with separate driver placed integrally in luminaire housing. Driver should be of THD ≤ 10% and power factor above ≥0.95, External surge protection device of 10 KV should be provided. LED lumen should be ≥ 3600. The luminaire body shall be painted with exterior grade of poly - Urethane/polyster quoting in required colour shade. LED CCT should be 3000K ingress protection IP 65, power rating 230 Volts, AC 50 Hz.with suitable civil foundation etc. (NS) LED Make: Everlite/ MSL

Supply Installation testing & commissioning of Video Management Server of 32 CH with 8 SATA Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge (NS)

Supply Installation testing & commissioning of outdor 4*4 box including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge (NS)

Supply Installation testing & commissioning of 9 U Server Rack with all Accesserieos including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge (NS)

Supply Installation testing & commissioning of 4 U Server Rack with all Accesserieos with including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge (NS)

S/E of PVC conduit pipe ISI marked (Medium) recessed in wall/ ceiling etc. including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge 25mm dia (NS)

S/E/T/C of Cat-6A cable in existing PVC conduit /PVC channel complete in all respect including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge (NS)

Supply Installation testing & commissioning of 6TB surveillance hard disk with the 3 years free comprehensive warranty period including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : WD-PURPLE/SEGATE

Supplying, Installation,Testing & Commissioning of 43 " LED /LFDFull HD TV Resolution 1920 x 1080 ,Contrast Ratio (Typical) 4000:1,Built-in Speaker (10W + 10W), Magic Clone (to USB), Auto Source Switching & Recovery, Lamp Error Detection, Super Clear Coating, Temperature Sensor, Plug and Play (DDC2B), Pivot Display, Clock Battery, PIP/PBP, Video Wall (10x10), Image Rotation, Button Lock, HDCP Support, Smart Scheduling, Smart F/W update, Built-In MagicInfo Premium-S with Mounting Brackets/stand as per Technical Specification complete in all respect. (NS) MAKE :- Sony / Samsung / LG

Supply Installation testing & commissioning of 24 Port POE Access Switch with the 3 years free comprehensive warranty period and 24x7 direct OEM TAC Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specifications : Switch should offer Wire-Speed and Non-Blocking Switching with 24 10/100/1000 RJ45 PoE/PoE+ Ethernet ports and additional 4 SFP+ (1G/10G ) fiber based ports, Minimum 2 port Populated with 10G MMF,Access Switches should support non-blocking switching fabric capacity of minimum 88 Gbps and minimum line-rate forwarding capacity of 57 Mpps, Access switch should support minimum 16K MAC addresses and minimum 4K active VLANs, Access Switch should have stacking capability with minimum stacking bandwidth of 40Gbps and should support a minimum of 8 units in a stack. Minimum one meter Stacking cables should be included in supplied material, Access switch should support up to 8 hardware queues per port, Access Switch should support full Layer 2 features like STP, RSTP, LACP, ACL, QoS, IGMP v1/v2, Access Switch should support basic L3 features like IPv4 & IPv6 static routing, Layer 3/4 ACLs, ECMP, virtual interfaces and routed interfaces from day 1, Access Switch should be upgradable to support advance Layer 3 features like, RIPv1/v2, OSPF v2, OSPFv3, and HSRP/VRRP in future with an additional software license upgrade,Access Switch should support minimum 1K IPv4 routes, The Access Switch should support IPv6 management features like IPv6 ping, IPv6 trace route, IPv6 Telnet, IPv6 TACACS, IPv6 and IPv6 RADIUS, All Switches and Transceivers should be of same OEM make,Access switch should support minimum 4K ACL rules ACL per Switch, Access switch should support SNMP v1/v2/v3, SSH, NTP and web management, Access switch should have 1G of RAM and 2G of Flash Memory.(NS) MAKE : RUKUS/CISCO/HP (NS)

Supply Installation testing & commissioning of 48 Port Non POE Access Switch with the 3 years free comprehensive warranty period and 24x7 direct OEM TAC Support having following technical specifications :Switch architecture should be Fixed Form factor/ stackable based.Switch should have wire-speed, non-blocking and fanless designe Architecture.Switch should have minimum of 48 x 10/100/1000 Mbps RJ45 ports and additional 4 SFP+ (1G/10G ) fiber based ports, Minimum 2 port Populated with 10G MMF.Switch should have minimum of 136 Gbps or more data switching capacity and 95 Mpps or more forwarding throughput.Access Switch should have stacking capability with minimum stacking bandwidth of 40Gbps and should support a minimum of 8 units in a stack Minimum one meter Stacking cables should be included in supplied material.Switch should support min 16 K MAC addresses and min 4000 active VLANs.Switch should have full Layer 2 features like STP, RSTP, MSTP/PVST, LACP/IEEE802.3ad, ACL, QoS and IGMPv1/v2/v3.Switch should have Static Routing for IPv4 & IPv6.Access Switch should be upgradable to support advance Layer 3 features like, RIPv1/v2, OSPF v2, OSPFv3, and HSRP/VRRP in future with an additional software license upgrade.Should support 4K IGMP Groups.Should support 8 queues per port and security protocols like RADIUS, TACACS/TACACS+, AAA & SSH.Switch should be quoted with 3 years direct OEM TAC support and Next Business day hardware shipment.Proposed switch should be IPv6 logo certified, including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. MAKE : RUKUS/CISCO/HP (NS)

Supply Installation testing & commissioning of Category 6 Patch Cord 6.5 feet, including 3 years free comprehensive warranty period and cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : DLINK/AMP/R&M

Supply Installation testing & commissioning of 24Port loaded Straight Jack pannel, including 3 years free comprehensive warranty period and cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : DLINK/AMP/R&M

Supply Installation testing & commissioning of Horizontal PVC Cable Manager - 1U , including 3 years free comprehensive warranty period and cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : DLINK/AMP/R&M

Supply Installation testing & commissioning of 10GBASE-SR,SFPP MMF LC CONNECTOR with the 3 years free comprehensive warranty period and 24x7 direct OEM TAC Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : RUKUS/CISCO/HP

Supply Installation testing & commissioning of DIRECT ATTACHED SFPP ACTIVE COPPER with 10G speed, 1M with the 3 years free comprehensive warranty period and 24x7 direct OEM TAC Support including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : RUKUS/CISCO/HP

Supply Installation testing & commissioning of Video Management Recorder with 3 Year free comprehensive warranty period including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specifications : Main Processor : Intel Quad-core Processor or better, Operating System :Embedded LINUX,IP Camera Input : 64 Channel or More, Two-way Talk : 1 Channel Input, 1 Channel Output/RCA, Interface : ≥2 HDMI (up to 3840 x 2160 , Different Source), ≥1 VGA, Compression : H.265/H.264, Resolution : 12MP, 8MP, 6MP, 5MP, 4MP, 3MP, 1080P, 1.3MP, 720P etc., Bandwidth : >320Mbps,Record Mode : Manual, Schedule (Regular, MD (Motion Detection), Alarm, Analytics), Holiday, Stop, Video Detection : Motion Detection/ Video Loss and Tampering/ Multiple VCA Event, Alarm input : ≥16 Channel, Relay Output : ≥8 Channel, Search Mode : Time /Date, Alarm, MD / Smart Search, Backup Mode : USB Device/Network/eSATA Device, Network Interface : 4 RJ-45 Ports (10/100/1000Mbps), Ethernet Port : 4 Ethernet Ports Joint Working or 4 Independent 1000Mbps Ethernet Ports, Network Function : HTTP, HTTPs, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS, IP Filter, PPPoE,DDNS, FTP, Alarm Server, IP Search etc., Optical Fiber Interface : ≥2 Giga Optical Fiber Interface, User Access : ≥128 users, Smart Phone : iPhone, iPad, Android, Interoperability : ONVIF 2.4, CGI Conformant, Internal HDD : 16 SATA III Ports, Up to 8 TB capacity for each HDD, HDD Mode : Single, Raid 0/1/5/6/10, Support Global HDD Hot-spare, eSATA : 1 eSATA Port, SAS : 1 Mini SAS Port, for Storage Expansion,Front Cover : Support Hot-swap, USB : 4 USB Ports (2 USB 2.0 , 2 USB 3.0 ), RS232 : 1 Port, for PC Communication and Keyboard, RS485 : 1 Port, for PTZ Control, Power Supply,Redudant Power supply : Support, Operating Conditions : -10°C ~ +55°C, Certifications : CE,UL,FCC (NS) MAKE : DAHUA/HYUNDAI/HONEYWELL

Supply Installation testing & commissioning of 17 U Wall Mount rack with front glass door lockable, Fans 90 Cfm 230 Vac, PDU Horizontal 5Amp with 6 Schokets, Cantilever Tray-1U, Horizontal PVC Cable Manager and Hardware front panel Mtg. including 3 years free comprehensive warranty period and cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : DLINK/AMP/R&M

Supply Installation testing & commissioning of AP Management License with 3 years comprehensive warranty period including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) MAKE : RUCKUS/CISCO/ARUBA

Supply Installation testing & commissioning of 12-core Singlemode OM3 OFC including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge.(NS) (MAKE : Molex/Siemon/Dlink)

Supply Installation testing & commissioning of Single mode Fibre Patch cord including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) (MAKE : Molex/Siemon/Dlink)

Supply Installation testing & commissioning of Black, 12F, L1U, Loaded with, Splice tray, Couplers & Pigtails including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) (MAKE : Molex/Legrand/Dlink)

Supply Installation testing & commissioning of Video Management Recorder with 3 Year free comprehensive warranty period including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge having following technical specifications : Main Processor : Intel Quad-core Processor or better, Operating System :Embedded LINUX,IP Camera Input : 64 Channel or More, Two-way Talk : 1 Channel Input, 1 Channel Output/RCA, Interface : ≥2 HDMI (up to 3840 x 2160 , Different Source), ≥1 VGA, Compression : H.265/H.264, Resolution : 12MP, 8MP, 6MP, 5MP, 4MP, 3MP, 1080P, 1.3MP, 720P etc., Bandwidth : >320Mbps,Record Mode : Manual, Schedule (Regular, MD (Motion Detection), Alarm, Analytics), Holiday, Stop, Video Detection : Motion Detection/ Video Loss and Tampering/ Multiple VCA Event, Alarm input : ≥16 Channel, Relay Output : ≥8 Channel, Search Mode : Time /Date, Alarm, MD / Smart Search, Backup Mode : USB Device/Network/eSATA Device, Network Interface : 4 RJ-45 Ports (10/100/1000Mbps), Ethernet Port : 4 Ethernet Ports Joint Working or 4 Independent 1000Mbps Ethernet Ports, Network Function : HTTP, HTTPs, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS, IP Filter, PPPoE,DDNS, FTP, Alarm Server, IP Search etc., Optical Fiber Interface : ≥2 Giga Optical Fiber Interface, User Access : ≥128 users, Smart Phone : iPhone, iPad, Android, Interoperability : ONVIF 2.4, CGI Conformant, Internal HDD : 16 SATA III Ports, Up to 8 TB capacity for each HDD, HDD Mode : Single, Raid 0/1/5/6/10, Support Global HDD Hot-spare, eSATA : 1 eSATA Port, SAS : 1 Mini SAS Port, for Storage Expansion,Front Cover : Support Hot-swap, USB : 4 USB Ports (2 USB 2.0 , 2 USB 3.0 ), RS232 : 1 Port, for PC Communication and Keyboard, RS485 : 1 Port, for PTZ Control, Power Supply,Redudant Power supply : Support, Operating Conditions : -10°C ~ +55°C, Certifications : CE,UL,FCC (NS) MAKE : DAHUA/HYUNDAI/HONEYWELL

Supply Installation testing & commissioning VAK make 'Amaze' LED light in 120W. Fitting is made of CNC cut MS closed by diffuser with durable proper silicone & rubber gasket. Fitting is coated with epoxy zinc phosphate primer and niched using environmentally stable PU paint. Amaze dimension 600x600x3400mm diffuser height 1200mm with sheet metal. Different kind of CNC cut design can be done as per client drawing Light output of source is more than 100lm/ watt, CRI>70, Surge protection 4KV, Optical part of Fitting is IP65, wired with Branded OSRAM or equivalent make LED and Fulham or equivalent constant current/ voltage driver. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Fitting is IP66 complete in all aspects with all accessories except foundation bolt. including cost of petty material required to complete the work upto the entire satisfaction of Engineer In Charge. (NS) Make VAK

S/E of trenchless boring of road by HDD machine for laying required size of HDPE pipe with socket reducer for OFC cable Duct Type as per dia of cable at the end of pipe to closed the end of pipe to avoid entering of sand in pipe and all petty material required to complete the job as per entire satisfaction of the EIC. (NS)( Pipe Cost including in this item ) (NS)

S/E of 4MP WDR IR Bullet Network Camera i Audio Interface : 1/1 Channel In/out, Intelligence (IVS) : Tripwire, Intrusion, Object Abandoned/Missing , Advanced Intelligent Functions : Face Detection ,Certification : CE, FCC,UL alongwith test report of the product ,MAKE : DAHUA/PANASONIC/HONEYWELL/HYUNDAI (NS)

SRISHTI CONSTRUCTIONS