Construction of side drain on Ghimana-Behbalpur app. road in Jind Distt. (Road ID 6612)

Amount

Earth work in excavation in foundations, trenches etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres. (HSR 6.6)

Cement concrete 1:8:16 with stone aggregate 40 mm Nominal sie in foundation and plinth. (HSR 10.28)

Cement concrete 1:6:12 with stone aggregate 40mm nominal size in foundation and plinth. (HSR 10.32)

Cement concrete 1:4:8 with stone aggregate 40 mm nominal size in foundation & plinth. (HSR 10.39)

Cement concrete 1:2:4 with stone aggregate 20mm nominal size in foundation and plinth.(HSR 10.41)

Cement Concrete 1:1:1/2:3 with stone aggregate 20mm nominal size in first storey upto 4 meters above plinth level. (HSR 10.60)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)].

First class brick work laid in cement sand mortar 1:4 in foundation plinth. (HSR 11.4)

Brick on edge or tile flooring laid in cement sand mortar1:4 on 75mm thick cement concrete 1:8:16 and 100mm sand filling and cement pointing 1:2 on top. (HSR 14.23)

12 mm Thick Cement Plaster 1:4 on the rough side of single or half brick wall. (HSR 15.5)

Cement pointing 1:2 deep variety on brick and tile work.(HSR 15.60)

Steel reinforcement TMT bars FE-550/EQR/FE-500 D grade or more for RCC work, where no included in the complete rate or RCC including straightening, bending, binding wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22) Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps, wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Providing, lowering, cutting, jointing and testing RCC pipe Class NP-3 as per IS 458-2003 with Spigot and Socketed joints manufactured with ISI marked Sulphate Resistance Cement as per ISI 12330 with rubber rings ISI marked, antitermite as required at site, into trenches, for all depths and laying out the same to correct alignment, gradients and levels including dressing and trimming and cutting of concrete beds and sides of trenches, if required, Jointing with rubber rings in trenches and jointing with 1:1½ cement sand mortar and with end dowels filled with 1:1½ cement sand mortar and finishing the joints at an angle of 45 degree with faces of spigot of socket joints cutting and finishing the cut surface to a uniform finish etc. as fully described in HSR item No. 29.38,29.44,29.45 & 29.46 including cartage, loading and unloading complete in all respects. (HSR 29.96-ix) 600mm dia

Narender Koshik, Contractor

The Ved Ashri Gate Pindara Ghati Coop LandC Society Ltd