Raga Bazar Line to Yad

Amount

SUB- EXTRA WIDENING ON CURVES, PASSING PLACES REGRADIENT & BACK CUTTING ETC.

Excavation in soil in Hilly Area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth with a lift upto 1.5 m and a lead upto 20 m as per Technical Specification Clause 1603.1

Excavation in hilly area in ordinary rock not requiring blasting by mechanical means including cutting and trimming of slopes and disposal of cut material with a lift upto 1.5 m and lead upto 20 m as per Clause 1603.2.

Excavation in hilly areas in hard rock requiring blasting, by mechanical means, lift upto 1.5 m and disposal of excavated rock upto a lead of 20 m as per Clause 1603.2.

SH: SHOULDER PREPARATION

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as

GSB LAYER (200 mm thick)

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (i)For Grading I Material

WBM 3 FOR BASE COURSE ( 75 mm thick)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.By Manual means

SH: Prime Coat.

Providing and applying of prime coat with bitumen emulsion(SS-1) on prepared surface of granular base i/c clearing of base surface and spraying emulsion at the rate of 1.2-1.50 kg per sqm. using mechanical means as per technical specification clause 502 (low porosity).

SH: Tack Coat

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

SH: PMC

Providing, laying and rolling of open graded primix carpet of 20 mm thickness composed od 13.20 mm to 5.60 mm aggrigate either using penetration grade bitumen or emulsion to required line ,gradeand level to serve as wearing course on a previosly prepared base i/c mixing in a suitable plant with 80-100 KN rolling capacity finished to required level and grade to be followed by seal coat.BITUMEN S-65

SH: Seal coat

Providing, laying and rolling of seal coat to sealing voids in a bitumenous surface laid to the specified grade and cross fall using typ-A, typ-B as per tech specf.

SH: Slab Culvert 1.50 mtr. Span

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and back filling in trenches with excavated suitable materials. I. Ordinary soil (i) upto 3 m depth

Providing Concrete for plain/reinforced concrete in open foundations complete as per drawings and techanical specifications Cluse 802,803,1202&1203 (I) PCC grade M 10 (ii) Nominal mix 1:3:6

Stone masonry work in cement mortar in foundations complete as per drawing and techanical specifications Clauses 702,704,1202&1203. I. Course Rubble masonery (2nd Sort) in 1 : 4 CM (1 cement : 4 fine sand)

Stone masonry work in cement mortar for substructure complete as per drawing and techanical specifications Clauses 702,704,1202&1204. I. Course Rubble masonery (2nd Sort) in 1 : 5 CM (1 cement : 5 fine sand)

BackFilling behind abutment, wing wall and return wall complete as per drawing & techanical specification Clause 1204.3.8 (I) (Grannular Meterial)

Providing weepholes in stone masonary RCC work, wing wall etc 100 dia AC pipe extending through the full width of the structures with slope of 1(V) :20(H) towards drawing face complete as per drawing and

Plain/reinforced cement concreete in substructure as per drawing and techanical specification Clauses 802,804,805,806,807,1202 and 1204 (RCC grade M15)0'!B30

Reinforced Cement Concrete M 25 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications Clauses 800 and 1211

Supplying, fitting and placing with MS bar reinforcment (Fe 415) in substructure as per drawing and techanical specification Clauses 1002,1005,1010&1202

Gabion Structure 2 mtr. ht.

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.

Providing and laying wire created boulder structures boulder size 22.5 cm to 45 cm having 25 kg average weight for each i/c dumping/laying in S.W.G. Wire mesh of 10 cm x 10 cm (woven diagonally) 4mm dia i/c packing with small size stone spalls and carrying of boulders from a lead of 50 mtr and lift up to 1.5 mtr i/c lying properly the mesh by cutting the mouth and hoisting of wire where felt necessary as per direction of Engineer-inCharge technical specifications Clause 1301. ( Based on SDB Rural Road Chapter-14, Item No.14.2)

Item : Retaining wall - 3.00 mtr Ht.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side and bottom and back filling in trenches with excaveted suitable material. (I) Ordinary Soil (i) upto 3 m depth.

Providing concrete for plain/renforced concrete in open foundations complete as per drawing and technical specification clouse 802, 803, 1202 & 1203. I. PCC Grade M10 (ii) Normal mixed 1:3:6 (hand mixing)

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 (I) Coursed Rubble masonry ( 2nd sort ) (ii) In 1:4 cement mortar

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 (I) Coursed Rubble masonry ( 2nd sort ) (iii) In 1:5cement mortar

Back filling behind abutment, wing wall and return wall complete as per drawing and technical specification, clouse 1204.3.8. i. Granular material

Earthen Side Drain

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side

SH: C.C. DRAIN.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side. Clause 1604

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 a) Nominal mix 1:3:6

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. (I) Random Rubble masonry (i) In 1:3 cement mortar

Cement Plaster 15 mm thick 1:4 on stone masonry

Neat cement punning

SH: TRAFFIC SIGNS, MARKINGS AND OTHER ROAD APPURTENANCES

Kilometre Stone. Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

i)5th Kilometer Stone (Precast)

ii)Ordinary Kilometer Stone (Precast)

iii)200 m stone (precast)

Providing and Fixing 'Logo' of PMGSY Project. Providing and fixing of typical PMGSY Citizen informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and fixing of typical PMGSY Citizen information sign board as per MORD specifications and drawing of cast-in-situ RCC,(Size of RCC post 25cmx25cmx90cm below G.L. & 15cmx15cmx245cm above G.L.),(Size of board 2x 90cmx80cmx7.5cm, ) incl.earth work, finishing with 15mm pluster 1:4 and neat cement punning, applying priming coat, painting and lettering with appropiate colour with required shade of approved quality ready mix paint.

Retro-reflectorised Traffic Signs. Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801.

Provision and fixing of traffic signs for limited period at suitable locations in construction zone comprising of warning zone,approch transition zone,working zone and terminal transition zone with a minimum distance of 2-3 from the edge of the carriage way. the bottom edge of the lowest sign plate to be not less than 2m above the road level,fixed on600mmx699mmx6mm angle iron post, founded and installed as per approved design and drawings,removed and disposed of after completion of construction work,all as per IRC:SP:55-2001.

a. Men at work.

b. Do not enter.

c. Stop.

d. Speed limit

e. Road closed

f. Traffic sign ahead

SH: Routine Maintenance

First Year

Second Year

Third Year

Fouth Year

Fifth Year

Add GST @ 12%

RAGIA KU ENTERPRISES